+++ /dev/null
-# Copyright (c) 2020 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-# http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/shared/default.robot
-|
-| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
-| ... | NIC_Intel-X710 | DOT1Q | L2BDMACLRN | BASE | DRV_VFIO_PCI
-| ... | RXQ_SIZE_0 | TXQ_SIZE_0 | GBP
-| ... | dot1q-l2bdbasemaclrn-gbp
-|
-| Suite Setup | Setup suite topology interfaces | performance
-| Suite Teardown | Tear down suite | performance
-| Test Setup | Setup test | performance
-| Test Teardown | Tear down test | performance
-|
-| Test Template | Local template
-|
-| Documentation | *RFC2544: Pkt throughput L2BD with IEEE 802.1Q and GBP test
-| ... | cases*
-|
-| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Dot1q-IPv4 for L2 switching of IPv4. \
-| ... | IEEE 802.1Q tagging is applied on both links TG-DUT1 .
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with:\
-| ... | 2 VLAN subinterfaces (VID 100 and 200),\
-| ... | 1 L2 BD with the 2 VLAN subinterfaces and a BVI,\
-| ... | 1 GBP L3 RD,\
-| ... | 1 GBP L2 BD with the L2 BD,\
-| ... | 1 GBP EPG EPG-1 with sclass 100, the GBP L2 BD and L3 RD,\
-| ... | 2 GBP external EP in EPG-1,\
-| ... | 2 external subnets with sclass 200 and 300,\
-| ... | Contracts allowing full communications between the 2 external subnets.\
-| ... | DUT1 tested with ${nic_name} with VF enabled.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
-| ... | Rate) with zero packet loss tolerance and throughput PDR (Partial Drop\
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
-| ... | of packets transmitted. NDR and PDR are discovered for different\
-| ... | Ethernet L2 frame sizes using MLRsearch library.\
-| ... | Test packets are generated by TG on\
-| ... | links to DUT. TG traffic profile contains two L3 flow-groups\
-| ... | (flow-group per direction, 254 flows per flow-group) with all packets\
-| ... | containing Ethernet header including IEEE 802.1Q tagging, IPv4 header\
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
-| ... | addresses of the TG node interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-| @{plugins_to_enable}= | dpdk_plugin.so | gbp_plugin.so | acl_plugin.so
-| ${crypto_type}= | ${None}
-| ${nic_name}= | Intel-X710
-| ${nic_driver}= | vfio-pci
-| ${nic_rxq_size}= | 0
-| ${nic_txq_size}= | 0
-| ${nic_pfs}= | 2
-| ${nic_vfs}= | 0
-| ${osi_layer}= | L2
-| ${overhead}= | ${4}
-# Traffic profile:
-| ${traffic_profile}= | trex-stl-dot1qip4-vlan1ip4src254ip4dst254-bvi
-
-*** Keywords ***
-| Local template
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD with VLAN and GBP config with ${phy_cores}\
-| | ... | physical core(s) for worker threads.
-| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
-| |
-| | ... | *Arguments:*
-| | ... | - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1).
-| | ... | Type: integer, string
-| | ... | - phy_cores - Number of physical cores. Type: integer
-| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
-| |
-| | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
-| |
-| | Set Test Variable | \${frame_size}
-| |
-| | Given Set Max Rate And Jumbo
-| | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
-| | And Pre-initialize layer driver | ${nic_driver}
-| | And Apply Startup configuration on all VPP DUTs
-| | When Initialize layer driver | ${nic_driver}
-| | And Initialize layer interface
-| | And Initialize layer dot1q
-| | And Initialize GBP routing domains
-| | Then Find NDR and PDR intervals using optimized search
-
-*** Test Cases ***
-| 64B-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 64B | 1C
-| | frame_size=${64} | phy_cores=${1}
-
-| 64B-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 64B | 2C
-| | frame_size=${64} | phy_cores=${2}
-
-| 64B-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 64B | 4C
-| | frame_size=${64} | phy_cores=${4}
-
-| 1518B-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 1518B | 1C
-| | frame_size=${1518} | phy_cores=${1}
-
-| 1518B-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 1518B | 2C
-| | frame_size=${1518} | phy_cores=${2}
-
-| 1518B-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 1518B | 4C
-| | frame_size=${1518} | phy_cores=${4}
-
-| 9000B-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 9000B | 1C
-| | frame_size=${9000} | phy_cores=${1}
-
-| 9000B-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 9000B | 2C
-| | frame_size=${9000} | phy_cores=${2}
-
-| 9000B-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | 9000B | 4C
-| | frame_size=${9000} | phy_cores=${4}
-
-| IMIX-1c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | IMIX | 1C
-| | frame_size=IMIX_v4_1 | phy_cores=${1}
-
-| IMIX-2c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | IMIX | 2C
-| | frame_size=IMIX_v4_1 | phy_cores=${2}
-
-| IMIX-4c-dot1q-l2bdbasemaclrn-gbp-ndrpdr
-| | [Tags] | IMIX | 4C
-| | frame_size=IMIX_v4_1 | phy_cores=${4}
Code Review / csit.git / blobdiff