Remove lbdpdk perf tests

[csit.git] / tests / vpp / perf / l2 / 2n1l-25ge2p1xxv710-eth-l2bdbasemaclrn-mrr.robot

diff --git a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-eth-l2bdbasemaclrn-mrr.robot b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-eth-l2bdbasemaclrn-mrr.robot
index c30879f..4e43db4 100644 (file)
--- a/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-eth-l2bdbasemaclrn-mrr.robot
+++ b/tests/vpp/perf/l2/2n1l-25ge2p1xxv710-eth-l2bdbasemaclrn-mrr.robot
@@ -30,34 +30,33 @@
 | ...
 | Documentation | *Raw results L2BD test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
 | ... | with single links between nodes.
 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge-domain
-| ... | and MAC learning enabled. DUT1 tested with 2p25GE NIC
-| ... | XVX710 by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge-domain\
+| ... | and MAC learning enabled. DUT1 tested with 2p25GE NIC XVX710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
 | ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
 # XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
-| ${s_24.5G} | ${24500000000}
+| ${s_24.5G}= | ${24500000000}
 # XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
-| ${s_18.75Mpps} | ${18750000}
+| ${s_18.75Mpps}= | ${18750000}
 # Traffic profile:
 | ${traffic_profile}= | trex-sl-2n-ethip4-ip4src254
 
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2 switching config.\
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Cfg] DUT runs L2BD switching config and uses ${phy_cores} physical\
+| | ... | core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize} frames using single\
 | | ... | trial throughput test.
 | | ...
@@ -73,10 +72,8 @@
 | | And Add PCI devices to all DUTs
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
-| | And Add DPDK dev default RXD to all DUTs | 2048
-| | And Add DPDK dev default TXD to all DUTs | 2048
 | | And Apply startup configuration on all VPP DUTs
-| | And Initialize L2 bridge domain in 2-node circular topology
+| | And Initialize L2 bridge domain in circular topology
 | | Then Traffic should pass with maximum rate
 | | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}