Add dot1q-l2bdbase-2vhost-[ndrpdr|mrr] perf tests for 2-node topology

[csit.git] / tests / vpp / perf / vm_vhost / 10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot

diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot b/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot
index 7a90799..4618f5d 100644 (file)
--- a/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot
+++ b/tests/vpp/perf/vm_vhost/10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-mrr.robot
@@ -30,27 +30,25 @@
 | ...
 | Test Template | Local Template
 | ...
-| Documentation | *Raw results L2BD test cases with vhost*
+| Documentation | *Raw results L2BD with vhost and IEEE 802.1Q test cases*
 | ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
 | ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. 802.1q
-| ... | tagging is applied on link between DUT1 and DUT2.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-
-| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via
-| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting
-| ... | vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M
-| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores
-| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to
-| ... | io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520
-| ... | Niantic by Intel.
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. IEEE\
+| ... | 802.1Q tagging is applied on link between DUT1 and DUT2.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\
+| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via\
+| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting\
+| ... | vhost-user interfaces, forwarding mode is set to io, rxd/txd=1024.\
+| ... | DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 254 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header\
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC\
 | ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
 
 *** Variables ***
 | ${subid}= | 10
@@ -69,8 +67,8 @@
 *** Keywords ***
 | Local Template
 | | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config.
-| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Cfg] Each DUT runs L2BD switching with VLAN and uses ${phy_cores}\
+| | ... | physical core(s) for worker threads.
 | | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
 | | ... | trial throughput test.
 | | ...
@@ -92,7 +90,7 @@
 | | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
 | | ... | ${s_limit} | ${framesize} | overhead=${overhead}
 | | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User and VLAN in a 3-node circular topology
+| | When Initialize L2 bridge domains with Vhost-User and VLAN in circular topology
 | | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2} | ${subid}
 | | ... | ${tag_rewrite}
 | | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user