FIX: remove previous QEMU build when needed to change qsz

[csit.git] / tests / vpp / perf / vm_vhost / 10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc.robot

diff --git a/tests/vpp/perf/vm_vhost/10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc.robot b/tests/vpp/perf/vm_vhost/10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc.robot
deleted file mode 100644 (file)
index 734b624..0000000
--- a/tests/vpp/perf/vm_vhost/10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc.robot
+++ /dev/null
@@ -1,658 +0,0 @@
-# Copyright (c) 2017 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/performance/performance_setup.robot
-| Library | resources.libraries.python.QemuUtils
-| ...
-| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
-| ... | NIC_Intel-X710 | ETH | L2BDMACLRN | BASE | VHOST | VM
-| ...
-| Suite Setup | Set up 3-node performance topology with DUT's NIC model
-| ... | L2 | Intel-X710
-| Suite Teardown | Tear down 3-node performance topology
-| ...
-| Test Setup | Set up performance test
-| Test Teardown | Tear down performance test with vhost and VM with dpdk-testpmd
-| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
-| ... | dut1_node=${dut1} | dut1_vm_refs=${dut1_vm_refs}
-| ... | dut2_node=${dut2} | dut2_vm_refs=${dut2_vm_refs}
-| ...
-| Documentation | *RFC2544: Pkt throughput L2BD test cases with vhost*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-
-| ... | domain and MAC learning enabled. Qemu Guest is connected to VPP via
-| ... | vhost-user interfaces. Guest is running DPDK testpmd interconnecting
-| ... | vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M
-| ... | memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores
-| ... | (1 main core and 4 cores dedicated for io), forwarding mode is set to
-| ... | io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710
-| ... | by Intel.
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using either binary search or linear search
-| ... | algorithms with configured starting rate and final step that determines
-| ... | throughput measurement resolution. Test packets are generated by TG on
-| ... | links to DUTs. TG traffic profile contains two L3 flow-groups
-| ... | (flow-group per direction, 253 flows per flow-group) with all packets
-| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static
-| ... | payload. MAC addresses are matching MAC addresses of the TG node
-| ... | interfaces.
-| ... | *[Ref] Applicable standard specifications:* RFC2544.
-
-*** Variables ***
-# X710 bandwidth limit
-| ${s_limit} | ${10000000000}
-# Socket names
-| ${bd_id1}= | 1
-| ${bd_id2}= | 2
-| ${sock1}= | /tmp/sock-1-${bd_id1}
-| ${sock2}= | /tmp/sock-1-${bd_id2}
-# Traffic profile:
-| ${traffic_profile} | trex-sl-3n-ethip4-ip4src254
-
-*** Test Cases ***
-| tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 64B | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc02-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 64B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc03-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc04-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc05-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame\
-| | ... | size using binary search start at 10GE linerate, step 5kpps.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | IMIX | 1T1C | STHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc06-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core,\
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame\
-| | ... | size using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | IMIX | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '1' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc07-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 64B | 2T2C | MTHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc08-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 64B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc09-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc10-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc11-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame\
-| | ... | size using binary search start at 10GE linerate, step 5kpps.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | IMIX | 2T2C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc12-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores,\
-| | ... | 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame\
-| | ... | size using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | IMIX | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '2' worker threads and '1' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc13-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 64B | 4T4C | MTHREAD | NDRDISC
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc14-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 64B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${64}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc15-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps.
-| | ...
-| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc16-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames\
-| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
-| | ...
-| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | ${1518}
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}
-
-| tc17-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port. [Ver] Find NDR for IMIX_v4_1 frame\
-| | ... | size using binary search start at 10GE linerate, step 5kpps.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | IMIX | 4T4C | MTHREAD | NDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find NDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold}
-
-| tc18-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
-| | [Documentation]
-| | ... | [Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores,\
-| | ... | 2 receive queues per NIC port. [Ver] Find PDR for IMIX_v4_1 frame\
-| | ... | size using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
-| | ... | IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
-| | ...
-| | [Tags] | IMIX | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
-| | ...
-| | ${framesize}= | Set Variable | IMIX_v4_1
-| | ${min_rate}= | Set Variable | ${10000}
-| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
-| | ${binary_min}= | Set Variable | ${min_rate}
-| | ${binary_max}= | Set Variable | ${max_rate}
-| | ${threshold}= | Set Variable | ${min_rate}
-| | ${dut1_vm_refs}= | Create Dictionary
-| | ${dut2_vm_refs}= | Create Dictionary
-| | Given Add '4' worker threads and '2' rxqueues in 3-node single-link circular topology
-| | And Add PCI devices to DUTs in 3-node single link topology
-| | And Add no multi seg to all DUTs
-| | And Apply startup configuration on all VPP DUTs
-| | When Initialize L2 bridge domains with Vhost-User in 3-node circular topology
-| | ... | ${bd_id1} | ${bd_id2} | ${sock1} | ${sock2}
-| | ${vm1}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut1} | ${sock1} | ${sock2} | DUT1_VM1
-| | Set To Dictionary | ${dut1_vm_refs} | DUT1_VM1 | ${vm1}
-| | ${vm2}= | And Configure guest VM with dpdk-testpmd connected via vhost-user
-| | ... | ${dut2} | ${sock1} | ${sock2} | DUT2_VM1
-| | Set To Dictionary | ${dut2_vm_refs} | DUT2_VM1 | ${vm2}
-| | Then Find PDR using binary search and pps | ${framesize} | ${binary_min}
-| | ... | ${binary_max} | ${traffic_profile}
-| | ... | ${min_rate} | ${max_rate} | ${threshold} | ${perf_pdr_loss_acceptance}
-| | ... | ${perf_pdr_loss_acceptance_type}