X-Git-Url: https://gerrit.fd.io/r/gitweb?p=csit.git;a=blobdiff_plain;f=tests%2Fsuites%2Fhoneycomb%2F1%20-%20interface_management.robot;fp=tests%2Fsuites%2Fhoneycomb%2F1%20-%20interface_management.robot;h=50eaa4edeb6db32a818486e13982baef0c5929eb;hp=0000000000000000000000000000000000000000;hb=b19bcf36d9d9be1a771495547335fcfc7b3e446b;hpb=56873a866fc17056e467fe7cafb2c987181f209a

diff --git a/tests/suites/honeycomb/1 - interface_management.robot b/tests/suites/honeycomb/1 - interface_management.robot
new file mode 100644
index 0000000000..50eaa4edeb
--- /dev/null
+++ b/tests/suites/honeycomb/1 - interface_management.robot	
@@ -0,0 +1,100 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Variables ***
+# Node and interface to run tests on.
+| ${node}= | ${nodes['DUT1']}
+| ${interface}= | ${node['interfaces'].values()[0]['name']}
+# Configuration which will be set and verified during tests.
+| @{ipv4_address}= | 192.168.0.2 | 255.255.255.0
+| @{ipv4_neighbor}= | 192.168.0.3 | 08:00:27:c0:5d:37
+| &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=9000
+| @{ipv6_address}= | 10::10 | 64
+| @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37
+| &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=9000
+| ... | dup-addr-detect-transmits=5
+| &{ethernet}= | mtu=9000
+| &{routing}= | vrf-id=27
+| &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=1000
+| ... | encap-vrf-id=1000
+
+*** Settings ***
+| Resource | resources/libraries/robot/default.robot
+| Resource | resources/libraries/robot/honeycomb/honeycomb.robot
+| Resource | resources/libraries/robot/honeycomb/interfaces.robot
+| Suite Setup | Run keywords | Setup all DUTs before test | AND
+| ... | Setup Honeycomb service on DUTs | ${node}
+| Documentation | *Honeycomb interface management test suite.*
+| ...
+| ... | Test suite uses the first interface of the first DUT node.
+
+*** Test Cases ***
+| Honeycomb configures and reads interface state
+| | [Documentation] | Check if Honeycomb API can modify the admin state of\
+| | ... | VPP interfaces.
+| | [Tags] | honeycomb_sanity
+| | Given Interface state is | ${node} | ${interface} | down
+| | When Honeycomb sets interface state | ${node} | ${interface} | up
+| | Then Interface state from Honeycomb should be
+| | ... | ${node} | ${interface} | up
+| | And Interface state from VAT should be | ${node} | ${interface} | up
+| | When Honeycomb sets interface state | ${node} | ${interface} | down
+| | Then Interface state from Honeycomb should be
+| | ... | ${node} | ${interface} | down
+| | And Interface state from VAT should be | ${node} | ${interface} | down
+
+| Honeycomb modifies interface configuration - ipv4
+| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4.
+| | [Tags] | honeycomb_sanity
+| | When Honeycomb sets interface ipv4 configuration
+| | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor}
+| | ... | ${ipv4_settings}
+| | Then IPv4 config from Honeycomb should be
+| | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor}
+| | ... | ${ipv4_settings}
+| | And IPv4 config from VAT should be
+| | ... | ${node} | ${interface} | @{ipv4_address}
+
+| Honeycomb modifies interface configuration - ipv6
+| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6.
+| | [Tags] | honeycomb_sanity
+| | When Honeycomb sets interface ipv6 configuration
+| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
+| | ... | ${ipv6_settings}
+| | Then IPv6 config from Honeycomb should be
+| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
+| | ... | ${ipv6_settings}
+| | And IPv6 config from VAT should be
+| | ... | ${node} | ${interface} | @{ipv6_address}
+
+| Honeycomb modifies interface configuration - ethernet,routing
+| | [Documentation] | Check if Honeycomb API can configure interface ethernet\
+| | ... | and routing settings.
+| | [Tags] | honeycomb_sanity
+| | When Honeycomb sets interface ethernet and routing configuration
+| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
+| | Then Interface ethernet and routing configuration from Honeycomb should be
+| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
+| | And Interface ethernet and routing configuration from VAT should be
+| | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']}
+
+| Honeycomb modifies interface configuration - VxLAN
+| | [Documentation] | Check if Honeycomb API can configure interface VxLAN \
+| | ... | settings.
+| | [Tags] | honeycomb_sanity
+| | When Honeycomb sets interface VxLAN configuration
+| | ... | ${node} | ${interface} | &{vxlan_settings}
+| | Then VxLAN configuration from Honeycomb should be
+| | ... | ${node} | ${interface} | &{vxlan_settings}
+| | And VxLAN configuration from VAT should be
+| | ... | ${node} | ${interface} | &{vxlan_settings}