X-Git-Url: https://gerrit.fd.io/r/gitweb?p=csit.git;a=blobdiff_plain;f=tests%2Fsuites%2Fperformance%2FLong_Xconnect_Dot1q_Intel-X520-DA2.robot;h=23339d6031e7ee68f15fdb28dfeef5b4a8e88025;hp=d13c707c565dbe98d0819939fe71b6f113d815ce;hb=49e919071acc924f93baeea63537e88ffa79fa8e;hpb=f94e16167519c74707ec8b606da3f7b97c749c66 diff --git a/tests/suites/performance/Long_Xconnect_Dot1q_Intel-X520-DA2.robot b/tests/suites/performance/Long_Xconnect_Dot1q_Intel-X520-DA2.robot index d13c707c56..23339d6031 100644 --- a/tests/suites/performance/Long_Xconnect_Dot1q_Intel-X520-DA2.robot +++ b/tests/suites/performance/Long_Xconnect_Dot1q_Intel-X520-DA2.robot @@ -21,33 +21,45 @@ | Suite Teardown | 3-node Performance Suite Teardown | Test Setup | Setup all DUTs before test | Test Teardown | Run Keyword | Remove startup configuration of VPP from all DUTs -| Documentation | *Throughput search suite (based on RFC2544).* +| Documentation | *RFC2544: Pkt throughput L2XC test cases* | ... -| ... | Test suite uses 3-node topology TG - DUT1 - DUT2 - TG, with one link -| ... | between nodes. Traffic profile contain 2 L2 streams (1 stream per -| ... | direction). Packets contain Ethernet header, IPv4 header, -| ... | IP protocol=61 and random payload. Ethernet header MAC addresses are -| ... | matching MAC addresses of the TG node. DUT nodes are interconnected -| ... | with VLAN dot1q configured interfaces with VLAN 10. +| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology +| ... | with single links between nodes. +| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4. +| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 cross- +| ... | connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel. +| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop +| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop +| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage +| ... | of packets transmitted. NDR and PDR are discovered for different +| ... | Ethernet L2 frame sizes using either binary search or linear search +| ... | algorithms with configured starting rate and final step that determines +| ... | throughput measurement resolution. Test packets are generated by TG on +| ... | links to DUTs. TG traffic profile contains two L3 flow-groups +| ... | (flow-group per direction, 253 flows per flow-group) with all packets +| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static +| ... | payload. MAC addresses are matching MAC addresses of the TG node +| ... | interfaces. +| ... | *[Ref] Applicable standard specifications:* RFC2544. *** Variables *** | ${subid}= | 10 | ${tag_rewrite}= | pop-1 *** Test Cases *** -| Find NDR by using RFC2544 binary search and 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC01: 64B NDR binary search - DUT L2XC with dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate by using binary search with -| | ... | threshold 0.1Mpps. Frames from and to TG are 64B long. Tagging is -| | ... | applied between DUTs inserting 4B VLAN ID into a packet header. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_68B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -65,20 +77,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC02: 64B PDR binary search - DUT L2XC with dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate by using binary search with -| | ... | threshold 0.1Mpps. Frames from and to TG are 64B long. Tagging is -| | ... | applied between DUTs inserting 4B VLAN ID into a packet header. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_68B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -98,19 +109,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR by using RFC2544 binary search and 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC03: 1518B NDR binary search - DUT L2XC with dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate by using binary search with -| | ... | threshold 10,000pps. Frames from and to TG are 1518B long. Tagging is -| | ... | applied between DUTs inserting 4B VLAN ID into a packet header. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1522B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -128,20 +139,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC04: 1518B PDR binary search - DUT L2XC with dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate by using binary search with -| | ... | threshold 10,000pps. Frames from and to TG are 1518B long. Tagging is -| | ... | applied between DUTs inserting 4B VLAN ID into a packet header. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1522B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -161,19 +171,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR by using RFC2544 binary search and 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC05: 9000B NDR binary search - DUT L2XC with dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with non drop rate by using binary search with -| | ... | threshold 5,000pps. Frames from and to TG are 9000B long. Tagging is -| | ... | applied between DUTs inserting 4B VLAN ID into a packet header. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9004B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | And VPP interfaces in path are up @@ -190,20 +200,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR by using RFC2544 binary search and 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC06: 9000B PDR binary search - DUT L2XC with dot1q - 1thread 1core 1rxq | | [Documentation] -| | ... | Find throughput with partial drop rate by using binary search with -| | ... | threshold 5,000pps. Frames from and to TG are 9000B long. Tagging is -| | ... | applied between DUTs inserting 4B VLAN ID into a packet header. Loss -| | ... | acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 1_THREAD_NOHTT_RSS_1 | SINGLE_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9004B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '1' worker threads and rss '1' without HTT to all DUTs +| | Given Add '1' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | And VPP interfaces in path are up @@ -222,19 +231,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC07: 64B NDR binary search - DUT L2XC with dot1q - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate by using binary search -| | ... | with threshold 0.1Mpps. Frames from and to TG are 64B long. Tagging -| | ... | is applied between DUTs inserting 4B VLAN ID into a packet header. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_68B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -252,20 +261,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC08: 64B PDR binary search - DUT L2XC with dot1q - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate by using binary -| | ... | search with threshold 0.1Mpps. Frames from and to TG are 64B long. -| | ... | Tagging is applied between DUTs inserting 4B VLAN ID into a packet -| | ... | header. Loss acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_68B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -285,20 +293,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC09: 1518B NDR binary search - DUT L2XC with dot1q - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate by using binary search -| | ... | with threshold 10,000pps. Frames from and to TG are 1518B long. -| | ... | Tagging is applied between DUTs inserting 4B VLAN ID into a packet -| | ... | header. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1522B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -316,20 +323,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC10: 1518B PDR binary search - DUT L2XC with dot1q - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate by using binary -| | ... | search with threshold 10,000pps. Frames from and to TG are 1518B long. -| | ... | Tagging is applied between DUTs inserting 4B VLAN ID into a packet -| | ... | header. Loss acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1522B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -349,20 +355,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 2 cores and rss 1 by using RFC2544 binary search and 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC11: 9000B NDR binary search - DUT L2XC with dot1q - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with non drop rate by using binary search -| | ... | with threshold 5,000pps. Frames from and to TG are 9000B long. -| | ... | Tagging is applied between DUTs inserting 4B VLAN ID into a packet -| | ... | header. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9004B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | And VPP interfaces in path are up @@ -379,20 +384,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 2 cores and rss 1 by using RFC2544 binary search and 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC12: 9000B PDR binary search - DUT L2XC with dot1q - 2threads 2cores 1rxq | | [Documentation] -| | ... | Find throughput on 2 cores with partial drop rate by using binary -| | ... | search with threshold 5,000pps. Frames from and to TG are 9000B long. -| | ... | Tagging is applied between DUTs inserting 4B VLAN ID into a packet -| | ... | header. Loss acceptance is set to 0.5 percent of transmitted packets. -| | [Tags] | 2_THREAD_NOHTT_RSS_1 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, \ +| | ... | 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9004B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '2' worker threads and rss '1' without HTT to all DUTs +| | Given Add '2' worker threads and rxqueues '1' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | And VPP interfaces in path are up @@ -411,20 +415,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC13: 64B NDR binary search - DUT L2XC with dot1q - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate by using -| | ... | binary search with threshold 0.1Mpps. Frames from and to TG are 64B -| | ... | long. Tagging is applied between DUTs inserting 4B VLAN ID into a -| | ... | packet header. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_68B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -442,21 +445,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 64B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC14: 64B PDR binary search - DUT L2XC with dot1q - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate by using -| | ... | binary search with threshold 0.1Mpps. Frames from and to TG are 64B -| | ... | long. Tagging is applied between DUTs inserting 4B VLAN ID into a -| | ... | packet header. Loss acceptance is set to 0.5 percent of transmitted -| | ... | packets. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 64 Byte frames +| | ... | using binary search start at 10GE linerate, step 100kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 64 | | ${min_rate}= | Set Variable | 100000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_68B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -476,20 +477,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC15: 1518B NDR binary search - DUT L2XC with dot1q - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate by using -| | ... | binary search with threshold 10,000pps. Frames from and to TG are -| | ... | 1518B long. Tagging is applied between DUTs inserting 4B VLAN ID into -| | ... | a packet header. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1522B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -507,21 +507,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 1518B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC16: 1518B PDR binary search - DUT L2XC with dot1q - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate by using -| | ... | binary search with threshold 10,000pps. Frames from and to TG are -| | ... | 1518B long. Tagging is applied between DUTs inserting 4B VLAN ID into -| | ... | a packet header. Loss acceptance is set to 0.5 percent of transmitted -| | ... | packets. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 1518 Byte frames +| | ... | using binary search start at 10GE linerate, step 10kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 1518 | | ${min_rate}= | Set Variable | 10000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_1522B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Add No Multi Seg to all DUTs | | And Apply startup configuration on all VPP DUTs @@ -541,20 +539,19 @@ | | ... | ${glob_loss_acceptance} | | ... | ${glob_loss_acceptance_type} -| Find NDR with 4 cores and rss 2 by using RFC2544 binary search and 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC17: 9000B NDR binary search - DUT L2XC with dot1q - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with non drop rate by using -| | ... | binary search with threshold 5,000pps. Frames from and to TG are -| | ... | 9000B long. Tagging is applied between DUTs inserting 4B VLAN ID into -| | ... | a packet header. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | NDR +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find NDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9004B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | And VPP interfaces in path are up @@ -571,21 +568,19 @@ | | ... | ${min_rate} | ${max_rate} | | ... | ${threshold} -| Find PDR with 4 cores and rss 2 by using RFC2544 binary search and 9000B frames through VLAN dot1q sub-interfaces inter-connected using L2 cross connect in 3-node topology +| TC18: 9000B PDR binary search - DUT L2XC with dot1q - 4threads 4cores 2rxq | | [Documentation] -| | ... | Find throughput on 4 cores and rss 2 with partial drop rate by using -| | ... | binary search with threshold 5,000pps. Frames from and to TG are -| | ... | 9000B long. Tagging is applied between DUTs inserting 4B VLAN ID into -| | ... | a packet header. Loss acceptance is set to 0.5 percent of transmitted -| | ... | packets. -| | [Tags] | 4_THREAD_NOHTT_RSS_2 | MULTI_THREAD | PDR +| | ... | [Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, \ +| | ... | 2 receive queues per NIC port. [Ver] Find PDR for 9000 Byte frames +| | ... | using binary search start at 10GE linerate, step 5kpps, LT=0.5%. +| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | | ${framesize}= | Set Variable | 9000 | | ${min_rate}= | Set Variable | 5000 | | ${max_rate}= | Set Variable | ${10Ge_linerate_pps_9004B} | | ${binary_min}= | Set Variable | ${min_rate} | | ${binary_max}= | Set Variable | ${max_rate} | | ${threshold}= | Set Variable | ${min_rate} -| | Given Add '4' worker threads and rss '2' without HTT to all DUTs +| | Given Add '4' worker threads and rxqueues '2' without HTT to all DUTs | | And Add all PCI devices to all DUTs | | And Apply startup configuration on all VPP DUTs | | And VPP interfaces in path are up