TB1 X710 topology file, X710 BD Long tests

Change-Id: Ib49dcd24be8e92ffb2bd1d12e3ea50cce125fb7e
Signed-off-by: Miroslav Miklus <mmiklus@cisco.com>

diff --git a/tests/perf/Long_Bridge_Domain_Intel-X710-DA2.robot b/tests/perf/Long_Bridge_Domain_Intel-X710-DA2.robot
new file mode 100644 (file)
index 0000000..70a5d85
--- /dev/null
+++ b/tests/perf/Long_Bridge_Domain_Intel-X710-DA2.robot
@@ -0,0 +1,196 @@
+# Copyright (c) 2016 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance.robot
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | PERFTEST_LONG
+| ... | NIC_Intel-X710
+| Suite Setup | 3-node Performance Suite Setup with DUT's NIC model
+| ... | L2 | Intel-X710
+| Suite Teardown | 3-node Performance Suite Teardown
+| Test Setup | Setup all DUTs before test
+| Test Teardown | Run Keywords
+| ...           | Run Keyword If Test Failed
+| ...           | Traffic should pass with no loss | 10
+| ...           | ${min_rate}pps | ${framesize} | 3-node-bridge
+| ...           | fail_on_loss=${False}
+| ...           | AND | Remove startup configuration of VPP from all DUTs
+| ...           | AND | Show vpp trace dump on all DUTs
+| Documentation | *RFC2544: Pkt throughput L2BD test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with L2 bridge-\
+| ... | domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC
+| ... | X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, 253 flows per flow-group) with all packets\
+| ... | containing Ethernet header, IPv4 header with IP protocol=61 and static\
+| ... | payload. MAC addresses are matching MAC addresses of the TG node\
+| ... | interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+#X710 bandwidth limit
+| ${s_limit} | ${10000000000}
+
+*** Keywords ***
+| L2 Bridge Domain NDR Binary Search
+| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq}
+| | # Test Variables required for test teardown
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Set Test Documentation | [Cfg] DUT runs L2BD switching config with ${wt}\
+| | Set Test Documentation | thread, ${wt} phy core, ${rxq}\ | append=True
+| | Set Test Documentation | receive queue per NIC port. | append=True
+| | Set Test Documentation | [Ver] Find NDR for ${framesize} Byte\ | append=True
+| | Set Test Documentation | frames using binary search start at\ | append=True
+| | Set Test Documentation | 10GE linerate, step ${threshold}pps. | append=True
+| | Add '${wt}' worker threads and rxqueues '${rxq}' in 3-node single-link topo
+| | Add PCI devices to DUTs from 3-node single link topology
+| | Run Keyword If | ${framesize} < ${1522} | Add No Multi Seg to all DUTs
+| | Apply startup configuration on all VPP DUTs
+| | L2 bridge domain initialized in a 3-node circular topology
+| | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | 3-node-bridge
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+
+| L2 Bridge Domain PDR Binary Search
+| | [Arguments] | ${framesize} | ${min_rate} | ${wt} | ${rxq}
+| | # Test Variables required for test teardown
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${max_rate}= | Calculate pps | ${s_limit} | ${framesize}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Set Test Documentation | [Cfg] DUT runs L2BD switching config with ${wt}\
+| | Set Test Documentation | thread, ${wt} phy core, ${rxq}\ | append=True
+| | Set Test Documentation | receive queue per NIC port. | append=True
+| | Set Test Documentation | [Ver] Find PDR for ${framesize} Byte\ | append=True
+| | Set Test Documentation | frames using binary search start at\ | append=True
+| | Set Test Documentation | 10GE linerate, step ${threshold}pps, | append=True
+| | Set Test Documentation | LT=${glob_loss_acceptance} | append=True
+| | Set Test Documentation | ${glob_loss_acceptance_type}. | append=True
+| | Add '${wt}' worker threads and rxqueues '${rxq}' in 3-node single-link topo
+| | Add PCI devices to DUTs from 3-node single link topology
+| | Run Keyword If | ${framesize} < ${1522} | Add No Multi Seg to all DUTs
+| | Apply startup configuration on all VPP DUTs
+| | L2 bridge domain initialized in a 3-node circular topology
+| | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | 3-node-bridge
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${glob_loss_acceptance} | ${glob_loss_acceptance_type}
+
+*** Test Cases ***
+| TC01: 64B NDR binary search - DUT L2BD - 1thread 1core 1rxq
+| | ... | ${64} | ${100000} | 1 | 1
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC02: 64B PDR binary search - DUT L2BD - 1thread 1core 1rxq
+| | ... | ${64} | ${100000} | 1 | 1
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC03: 1518B NDR binary search - DUT L2BD - 1thread 1core 1rxq
+| | ... | ${1518} | ${10000} | 1 | 1
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC04: 1518B PDR binary search - DUT L2BD - 1thread 1core 1rxq
+| | ... | ${1518} | ${10000} | 1 | 1
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC05: 9000B NDR binary search - DUT L2BD - 1thread 1core 1rxq
+| | ... | ${9000} | ${10000} | 1 | 1
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | NDR
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC06: 9000B PDR binary search - DUT L2BD - 1thread 1core 1rxq
+| | ... | ${9000} | ${10000} | 1 | 1
+| | [Tags] | 1_THREAD_NOHTT_RXQUEUES_1 | SINGLE_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC07: 64B NDR binary search - DUT L2BD - 2thread 2core 1rxq
+| | ... | ${64} | ${100000} | 2 | 1
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC08: 64B PDR binary search - DUT L2BD - 2thread 2core 1rxq
+| | ... | ${64} | ${100000} | 2 | 1
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC09: 1518B NDR binary search - DUT L2BD - 2thread 2core 1rxq
+| | ... | ${1518} | ${10000} | 2 | 1
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC10: 1518B PDR binary search - DUT L2BD - 2thread 2core 1rxq
+| | ... | ${1518} | ${10000} | 2 | 1
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC11: 9000B NDR binary search - DUT L2BD - 2thread 2core 1rxq
+| | ... | ${9000} | ${10000} | 2 | 1
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | NDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC12: 9000B PDR binary search - DUT L2BD - 2thread 2core 1rxq
+| | ... | ${9000} | ${10000} | 2 | 1
+| | [Tags] | 2_THREAD_NOHTT_RXQUEUES_1 | MULTI_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC13: 64B NDR binary search - DUT L2BD - 4thread 4core 2rxq
+| | ... | ${64} | ${100000} | 4 | 2
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC14: 64B PDR binary search - DUT L2BD - 4thread 4core 2rxq
+| | ... | ${64} | ${100000} | 4 | 2
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC15: 1518B NDR binary search - DUT L2BD - 4thread 4core 2rxq
+| | ... | ${1518} | ${10000} | 4 | 2
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC16: 1518B PDR binary search - DUT L2BD - 4thread 4core 2rxq
+| | ... | ${1518} | ${10000} | 4 | 2
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search
+
+| TC17: 9000B NDR binary search - DUT L2BD - 4thread 4core 2rxq
+| | ... | ${9000} | ${10000} | 4 | 2
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | NDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain NDR Binary Search
+
+| TC18: 9000B PDR binary search - DUT L2BD - 4thread 4core 2rxq
+| | ... | ${9000} | ${10000} | 4 | 2
+| | [Tags] | 4_THREAD_NOHTT_RXQUEUES_2 | MULTI_THREAD | PDR | SKIP_PATCH
+| | [Template] | L2 Bridge Domain PDR Binary Search

diff --git a/topologies/available/lf_testbed1.yaml b/topologies/available/lf_testbed1.yaml
index 3c3c7df..51593e7 100644 (file)
--- a/topologies/available/lf_testbed1.yaml
+++ b/topologies/available/lf_testbed1.yaml
@@ -143,19 +143,19 @@ nodes:
         pci_address: "0000:85:00.1"
         link: link7
         model: Intel-XL710
+      port7:
+        # t1-sut1-c5/p1 - 10GE port1 on Intel NIC x710 2p10GE.
+        mac_address: "3c:fd:fe:9c:ee:c4"
+        pci_address: "0000:87:00.0"
+        link: link24
+        model: Intel-X710
+      port8:
+        # t1-sut1-c5/p2 - 10GE port2 on Intel NIC x710 2p10GE.
+        mac_address: "3c:fd:fe:9c:ee:c5"
+        pci_address: "0000:87:00.1"
+        link: link9
+        model: Intel-X710
 ###TODO:links need to be identified before enabling interfaces###
-#      port7:
-#        # t1-sut1-c5/p1 - 10GE port1 on Intel NIC x710 2p10GE.
-#        mac_address: "3c:fd:fe:9c:ee:c4"
-#        pci_address: "0000:87:00.0"
-#        link: link15
-#        model: Intel-X710
-#      port8:
-#        # t1-sut1-c5/p2 - 10GE port2 on Intel NIC x710 2p10GE.
-#        mac_address: "3c:fd:fe:9c:ee:c5"
-#        pci_address: "0000:87:00.1"
-#        link: link9
-#        model: Intel-X710
 #      port9:
 #        # t1-sut1-cm/p1 - 10GE port1 on Cisco VIC 1227 2p10GE.
 #        mac_address: "00:fe:c8:e4:d0:1b"
@@ -212,19 +212,19 @@ nodes:
         pci_address: "0000:85:00.1"
         link: link23
         model: Intel-XL710
+      port7:
+        # t1-sut2-c5/p1 - 10GE port1 on Intel NIC x710 2p10GE.
+        mac_address: "3c:fd:fe:9c:ef:94"
+        pci_address: "0000:87:00.0"
+        link: link10
+        model: Intel-X710
+      port8:
+        # t1-sut2-c5/p2 - 10GE port2 on Intel NIC x710 2p10GE.
+        mac_address: "3c:fd:fe:9c:ef:95"
+        pci_address: "0000:87:00.1"
+        link: link24
+        model: Intel-X710
 ###TODO:links need to be identified before enabling interfaces###
-#      port7:
-#        # t1-sut2-c5/p1 - 10GE port1 on Intel NIC x710 2p10GE.
-#        mac_address: "3c:fd:fe:9c:ef:94"
-#        pci_address: "0000:87:00.0"
-#        link: link10
-#        model: Intel-X710
-#      port8:
-#        # t1-sut2-c5/p2 - 10GE port2 on Intel NIC x710 2p10GE.
-#        mac_address: "3c:fd:fe:9c:ef:95"
-#        pci_address: "0000:87:00.1"
-#        link: link15
-#        model: Intel-X710
 #      port9:
 #        # t1-sut2-cm/p1 - 10GE port1 on Cisco VIC 1227 2p10GE.
 #        mac_address: "00:fe:c8:e5:44:4c"