-::
-
- $ cat /etc/vpp/startup.conf
- unix {
- nodaemon
- log /var/log/vpp/vpp.log
- full-coredump
- cli-listen /run/vpp/cli.sock
- gid vpp
- }
-
- api-trace {
- ## This stanza controls binary API tracing. Unless there is a very strong reason,
- ## please leave this feature enabled.
- on
- ## Additional parameters:
- ##
- ## To set the number of binary API trace records in the circular buffer, configure nitems
- ##
- ## nitems <nnn>
- ##
- ## To save the api message table decode tables, configure a filename. Results in /tmp/<filename>
- ## Very handy for understanding api message changes between versions, identifying missing
- ## plugins, and so forth.
- ##
- ## save-api-table <filename>
- }
-
- api-segment {
- gid vpp
- }
-
- socksvr {
- default
- }
-
- cpu {
- ## In the VPP there is one main thread and optionally the user can create worker(s)
- ## The main thread and worker thread(s) can be pinned to CPU core(s) manually or automatically
-
- ## Manual pinning of thread(s) to CPU core(s)
-
- ## Set logical CPU core where main thread runs, if main core is not set
- ## VPP will use core 1 if available
- # main-core 1
-
- ## Set logical CPU core(s) where worker threads are running
- # corelist-workers 2-3,18-19
-
- ## Automatic pinning of thread(s) to CPU core(s)
-
- ## Sets number of CPU core(s) to be skipped (1 ... N-1)
- ## Skipped CPU core(s) are not used for pinning main thread and working thread(s).
- ## The main thread is automatically pinned to the first available CPU core and worker(s)
- ## are pinned to next free CPU core(s) after core assigned to main thread
- # skip-cores 4
-
- ## Specify a number of workers to be created
- ## Workers are pinned to N consecutive CPU cores while skipping "skip-cores" CPU core(s)
- ## and main thread's CPU core
- # workers 2
-
- ## Set scheduling policy and priority of main and worker threads
-
- ## Scheduling policy options are: other (SCHED_OTHER), batch (SCHED_BATCH)
- ## idle (SCHED_IDLE), fifo (SCHED_FIFO), rr (SCHED_RR)
- # scheduler-policy fifo
-
- ## Scheduling priority is used only for "real-time policies (fifo and rr),
- ## and has to be in the range of priorities supported for a particular policy
- # scheduler-priority 50
- }
-
- # dpdk {
- ## Change default settings for all interfaces
- # dev default {
- ## Number of receive queues, enables RSS
- ## Default is 1
- # num-rx-queues 3
-
- ## Number of transmit queues, Default is equal
- ## to number of worker threads or 1 if no workers treads
- # num-tx-queues 3
-
- ## Number of descriptors in transmit and receive rings
- ## increasing or reducing number can impact performance
- ## Default is 1024 for both rx and tx
- # num-rx-desc 512
- # num-tx-desc 512
-
- ## VLAN strip offload mode for interface
- ## Default is off
- # vlan-strip-offload on
- # }
-
- ## Whitelist specific interface by specifying PCI address
- # dev 0000:02:00.0
-
- ## Blacklist specific device type by specifying PCI vendor:device
- ## Whitelist entries take precedence
- # blacklist 8086:10fb
-
- ## Set interface name
- # dev 0000:02:00.1 {
- # name eth0
- # }
-
- ## Whitelist specific interface by specifying PCI address and in
- ## addition specify custom parameters for this interface
- # dev 0000:02:00.1 {
- # num-rx-queues 2
- # }
-
- ## Specify bonded interface and its slaves via PCI addresses
- ##
- ## Bonded interface in XOR load balance mode (mode 2) with L3 and L4 headers
- # vdev eth_bond0,mode=2,slave=0000:02:00.0,slave=0000:03:00.0,xmit_policy=l34
- # vdev eth_bond1,mode=2,slave=0000:02:00.1,slave=0000:03:00.1,xmit_policy=l34
- ##
- ## Bonded interface in Active-Back up mode (mode 1)
- # vdev eth_bond0,mode=1,slave=0000:02:00.0,slave=0000:03:00.0
- # vdev eth_bond1,mode=1,slave=0000:02:00.1,slave=0000:03:00.1
-
- ## Change UIO driver used by VPP, Options are: igb_uio, vfio-pci,
- ## uio_pci_generic or auto (default)
- # uio-driver vfio-pci
-
- ## Disable multi-segment buffers, improves performance but
- ## disables Jumbo MTU support
- # no-multi-seg
-
- ## Increase number of buffers allocated, needed only in scenarios with
- ## large number of interfaces and worker threads. Value is per CPU socket.
- ## Default is 16384
- # num-mbufs 128000
-
- ## Change hugepages allocation per-socket, needed only if there is need for
- ## larger number of mbufs. Default is 256M on each detected CPU socket
- # socket-mem 2048,2048
-
- ## Disables UDP / TCP TX checksum offload. Typically needed for use
- ## faster vector PMDs (together with no-multi-seg)
- # no-tx-checksum-offload
- # }
-
-
- # plugins {
- ## Adjusting the plugin path depending on where the VPP plugins are
- # path /ws/vpp/build-root/install-vpp-native/vpp/lib/vpp_plugins
-
- ## Disable all plugins by default and then selectively enable specific plugins
- # plugin default { disable }
- # plugin dpdk_plugin.so { enable }
- # plugin acl_plugin.so { enable }
-
- ## Enable all plugins by default and then selectively disable specific plugins
- # plugin dpdk_plugin.so { disable }
- # plugin acl_plugin.so { disable }
- # }
Code Review / csit.git / commitdiff