#. DPDK PERFORMANCE TESTS
- - **Intel Xeon 2n-skx, 3n-skx testbeds**: Testpmd and L3fwd
- performance test data is not included in this report version.
- This is due to the lower performance and behaviour inconsistency
- of these systems following the upgrade of processor microcode
- packages (skx ucode 0x2000064) as part of updating Ubuntu 18.04
- LTS kernel version. Tested VPP and DPDK applications (L3fwd) are
- affected. Skx test data will be added in subsequent maintenance
- report version(s) once the issue is resolved. See
- :ref:`dpdk_known_issues`.
+ - Refactor of CSIT initialization helper scripts for DPDK testpmd
+ and l3fwd. Removing obsolete parameters from DPDK testpmd and l3fwd
+ command line.
- - **Intel Xeon 2n-clx testbeds**: DPDK performance test data is now
- included in this report, after resolving the issue of lower
- performance and behaviour inconsistency of these systems due to
- the Linux kernel driven upgrade of processor microcode packages
- to 0x500002c. The resolution is to use latest SuperMicro BIOS 3.2
- (for X11DPG-QT motherboards used) that upgrades processor
- microcode to 0x500002c, AND NOT kernel provided ucode package as
- it does put THE system into sub-optimal state.
+ - Fixed 9000B L2 packet size tests not passing for all NICs.
+ - Fixed DPDK compilation and test initialization of Mellanox NICs using
+ CONFIG_RTE_LIBRTE_MLX5_PMD=y in compile configuration.
#. DPDK RELEASE VERSION CHANGE
- |csit-release| tested |dpdk-release|, as used by |vpp-release|.
-#. TEST ENVIRONMENT
-
- - **TRex Fortville NIC Performance**: Received FVL fix from Intel
- resolving TRex low throughput issue. TRex per FVL NIC throughput
- increased from ~27 Mpps to the nominal ~37 Mpps. For detail see
- `CSIT-1503 <https://jira.fd.io/browse/CSIT-1503>`_ and `TRex-519
- <https://trex-tgn.cisco.com/youtrack/issue/trex-519>`_].
-
- - **New Intel Xeon Cascadelake Testbeds**: Added performance tests
- for 2-Node-Cascadelake (2n-clx) testbeds with x710, xxv710 and
- cx556a-edat NIC cards.
-
-..
- // Alternative Note for 1st Bullet when bad microcode Skx, Clx results are published
- - **Intel Xeon 2n-skx, 3n-skx and 2n-clx testbeds**: Testpmd and
- L3fwd performance test data is included in this report version,
- but it shows lower performance and behaviour inconsistency of
- these systems following the upgrade of processor microcode
- packages (skx ucode 0x2000064, clx ucode 0x500002c) as part of
- updating Ubuntu 18.04 LTS kernel version. Tested VPP and DPDK
- applications (L3fwd) are affected. Skx and Clx test data will be
- corrected in subsequent maintenance report version(s) once the
- issue is resolved. See :ref:`vpp_known_issues`.
-
.. _dpdk_known_issues:
Known Issues
+----+------------------------------------------+----------------------------------------------------------------------------------------------------------+
| # | JiraID | Issue Description |
+====+==========================================+==========================================================================================================+
-| 1 | `CSIT-1675 | Intel Xeon 2n-skx, 3n-skx and 2n-clx testbeds behaviour and performance became inconsistent following |
-| | <https://jira.fd.io/browse/CSIT-1675>`_ | the upgrade to the latest Ubuntu 18.04 LTS kernel version (4.15.0-72-generic) and associated microcode |
-| | | packages (skx ucode 0x2000064, clx ucode 0x500002c). VPP as well as DPDK L3fwd tests are affected. |
+| 1 | `CSIT-1701 | DPDK L3fwd tests with 9000B L2 packet size are not passing with Mellanox NICs. |
+| | <https://jira.fd.io/browse/CSIT-1701>`_ | L3fwd application does not accept parameter for increasing -mbuf-size in same way DPDK testpmd does. |
+----+------------------------------------------+----------------------------------------------------------------------------------------------------------+
Overview
========
-DPDK performance test results are reported for all three physical
-testbed types present in FD.io labs: 3-Node Xeon Haswell (3n-hsw),
-3-Node Xeon Skylake (3n-skx), 2-Node Xeon Skylake (2n-skx) and installed
-NIC models. For description of physical testbeds used for DPDK
-performance tests please refer to :ref:`tested_physical_topologies`.
+DPDK performance test results are reported for all physical testbed types
+present in FD.io labs and installed NIC models. For description of physical
+testbeds used for DPDK performance tests please refer to
+:ref:`tested_physical_topologies`.
Logical Topologies
------------------
.. code-block:: bash
- make install T=<arch>-native-linuxapp-gcc -j
+ make install T=<arch>-<machine>-linuxapp-gcc -j
Testpmd Startup Configuration
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-Testpmd startup configuration changes per test case with different
-settings for `$$CORES`, `$$RXQ` and max-pkt-len parameter if test is
+Testpmd startup configuration changes per test case with different settings for
+`$$INT`, `$$CORES`, `$$RXQ`, `$$RXD` and max-pkt-len parameter if test is
sending jumbo frames. Startup command template:
.. code-block:: bash
- testpmd -c $$CORE_MASK -n 4 -- --numa --nb-ports=2 --portmask=0x3 --nb-cores=$$CORES [--max-pkt-len=9000] --txqflags=0 --forward-mode=io --rxq=$$RXQ --txq=$$TXQ --burst=64 --rxd=1024 --txd=1024 --disable-link-check --auto-start
+ testpmd -v -l $$CORE_LIST -w $$INT1 -w $$INT2 --master-lcore 0 --in-memory -- --forward-mode=io --burst=64 --txd=$$TXD --rxd=$$RXD --txq=$$TXQ --rxq=$$RXQ --tx-offloads=0x0 --numa --auto-start --total-num-mbufs=16384 --nb-ports=2 --portmask=0x3 --disable-link-check --max-pkt-len=$$PKT_LEN [--mbuf-size=16384] --nb-cores=$$CORES
L3FWD Startup Configuration
~~~~~~~~~~~~~~~~~~~~~~~~~~~
-L3FWD startup configuration changes per test case with different
-settings for `$$CORES` and enable-jumbo parameter if test is sending
-jumbo frames. Startup command template:
+L3FWD startup configuration changes per test case with different settings for
+`$$INT`, `$$CORES` and enable-jumbo parameter if test is sending jumbo frames.
+Startup command template:
.. code-block:: bash
- l3fwd -l $$CORE_LIST -n 4 -- -P -L -p 0x3 --config='${port_config}' [--enable-jumbo --max-pkt-len=9000] --eth-dest=0,${adj_mac0} --eth-dest=1,${adj_mac1} --parse-ptype
-
+ l3fwd -v -l $$CORE_LIST -w $$INT1 -w $$INT2 --master-lcore 0 --in-memory -- --parse-ptype --eth-dest="0,${adj_mac0}" --eth-dest="1,${adj_mac1}" --config="${port_config}" [--enable-jumbo] -P -L -p 0x3
.. include:: ../introduction/test_environment_tg.rst
--- /dev/null
+Mellanox NIC
+------------
+
+Performance test results using Mellanox ConnectX5 2p100GE are reported for
+2-Node Xeon Cascade Lake physical testbed type present in FD.io labs. For
+description of physical testbeds used please refer to
+:ref:`tested_physical_topologies`.
+
+Mellanox NIC settings
+~~~~~~~~~~~~~~~~~~~~~
+
+Mellanox ConnectX5 NIC settings are following recommendations from
+[DpdkPerformanceReport]_, [MellanoxDpdkGuide]_ and [MellanoxDpdkBits]_.
+Specifically:
+
+- Flow Control OFF:
+ ::
+
+ $ ethtool -A $netdev rx off tx off
+
+- Change PCI MaxReadReq to 1024B for each port of each NIC:
+ ::
+
+ $ setpci -s $PORT_PCI_ADDRESS 68.w=3BCD
+
+- Set CQE COMPRESSION to "AGGRESSIVE":
+ ::
+
+ $ mlxconfig -d $PORT_PCI_ADDRESS set CQE_COMPRESSION=1
+
+Mellanox :abbr:`OFED (OpenFabrics Enterprise Distribution)` driver of version
+4.6-1.0.1.1 is installed and used to manage the NIC settings.
+
+::
+
+ $ sudo ethtool -i enp94s0f0
+ driver: mlx5_core
+ version: 4.6-1.0.1
+ firmware-version: 16.25.1020 (MT_0000000009)
+ expansion-rom-version:
+ bus-info: 0000:5e:00.0
+ supports-statistics: yes
+ supports-test: yes
+ supports-eeprom-access: no
+ supports-register-dump: no
+ supports-priv-flags: yes
+
+::
+
+ $ sudo lspci -vvvs 5e:00.0
+ 5e:00.0 Ethernet controller: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
+ Subsystem: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
+ Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
+ Latency: 0, Cache Line Size: 32 bytes
+ Interrupt: pin A routed to IRQ 37
+ NUMA node: 0
+ Region 0: Memory at 38fffe000000 (64-bit, prefetchable) [size=32M]
+ Expansion ROM at c5e00000 [disabled] [size=1M]
+ Capabilities: [60] Express (v2) Endpoint, MSI 00
+ DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
+ ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
+ DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
+ RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset-
+ MaxPayload 256 bytes, MaxReadReq 4096 bytes
+ DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
+ LnkCap: Port #0, Speed 16GT/s, Width x16, ASPM not supported, Exit Latency L0s unlimited, L1 unlimited
+ ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
+ LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
+ LnkSta: Speed 8GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
+ DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
+ LnkCtl2: Target Link Speed: 16GT/s, EnterCompliance- SpeedDis-
+ Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
+ Compliance De-emphasis: -6dB
+ LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+, EqualizationPhase1+
+ EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
+ Capabilities: [48] Vital Product Data
+ Product Name: CX556A - ConnectX-5 QSFP28
+ Read-only fields:
+ [PN] Part number: MCX556A-EDAT
+ [EC] Engineering changes: AA
+ [V2] Vendor specific: MCX556A-EDAT
+ [SN] Serial number: MT1945X00360
+ [V3] Vendor specific: f8d15ef7e701ea118000b8599ffe4aa8
+ [VA] Vendor specific: MLX:MODL=CX556A:MN=MLNX:CSKU=V2:UUID=V3:PCI=V0
+ [V0] Vendor specific: PCIeGen4 x16
+ [RV] Reserved: checksum good, 2 byte(s) reserved
+ End
+ Capabilities: [9c] MSI-X: Enable+ Count=64 Masked-
+ Vector table: BAR=0 offset=00002000
+ PBA: BAR=0 offset=00003000
+ Capabilities: [c0] Vendor Specific Information: Len=18 <?>
+ Capabilities: [40] Power Management version 3
+ Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold+)
+ Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
+ Capabilities: [100 v1] Advanced Error Reporting
+ UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
+ UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
+ UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
+ CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
+ AERCap: First Error Pointer: 04, GenCap+ CGenEn- ChkCap+ ChkEn-
+ Capabilities: [150 v1] Alternative Routing-ID Interpretation (ARI)
+ ARICap: MFVC- ACS-, Next Function: 1
+ ARICtl: MFVC- ACS-, Function Group: 0
+ Capabilities: [1c0 v1] #19
+ Capabilities: [230 v1] Access Control Services
+ ACSCap: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
+ ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
+ Capabilities: [320 v1] #27
+ Capabilities: [370 v1] #26
+ Capabilities: [420 v1] #25
+ Kernel driver in use: mlx5_core
+ Kernel modules: mlx5_core
+
+TG and SUT settings
+~~~~~~~~~~~~~~~~~~~
+
+For the TG and SUT environment settings please refer to
+:ref:`_vpp_test_environment` and :ref:`_dpdk_test_environment`.
+
+Links
+~~~~~
+
+.. [DpdkPerformanceReport] `DPDK 19.11 performance report <http://static.dpdk.org/doc/perf/DPDK_19_11_Mellanox_NIC_performance_report.pdf>`
+.. [MellanoxDpdkGuide] `Mellanox DPDK guide <https://www.mellanox.com/related-docs/prod_software/MLNX_DPDK_Quick_Start_Guide_v16.11_3.0.pdf>`
+.. [MellanoxDpdkBits] `Mellanox DPDK bits <https://community.mellanox.com/s/article/mellanox-dpdk>`
Usage
~~~~~
-`TRex traffic generator <https://trex-tgn.cisco.com>`_ is used for all
-CSIT performance tests. TRex stateless mode is used to measure NDR and
-PDR throughputs using MLRsearch and to measure maximum transer rate
-in MRR tests.
+`TRex traffic generator <https://trex-tgn.cisco.com>`_ is used for majority of
+CSIT performance tests. TRex stateless mode is used to measure NDR and PDR
+throughputs using MLRsearch and to measure maximum transfer rate in MRR tests.
TRex is installed and run on the TG compute node. The typical procedure is:
-- If the TRex is not already installed on TG, it is installed in the
- suite setup phase - see `TRex installation`_.
- TRex configuration is set in its configuration file
::
- /etc/trex_cfg.yaml
+ $ sudo -E -S sh -c 'cat << EOF > /etc/trex_cfg.yaml
+ - version: 2
+ c: 15
+ limit_memory: 8192
+ interfaces: ["${pci1}","${pci2}"]
+ port_info:
+ - dest_mac: [${dest_mac1}]
+ src_mac: [${src_mac1}]
+ - dest_mac: [${dest_mac2}]
+ src_mac: [${src_mac2}]
+ platform :
+ master_thread_id: 0
+ latency_thread_id: 16
+ dual_if:
+ - socket: 0
+ threads: [1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15]
+ EOF'
-- TRex is started in the background mode
+- TRex is started in the interactive mode as a background service
::
- $ sh -c 'cd <t-rex-install-dir>/scripts/ && sudo nohup ./t-rex-64 -i --prefix $(hostname) --hdrh --no-scapy-server > /tmp/trex.log 2>&1 &' > /dev/null
+ $ sh -c 'cd <t-rex-install-dir>/scripts/ && \
+ sudo nohup ./t-rex-64 -i --prefix $(hostname) --hdrh --no-scapy-server \
+ > /tmp/trex.log 2>&1 &' > /dev/null
- There are traffic streams dynamically prepared for each test, based on traffic
- profiles. The traffic is sent and the statistics obtained using
+ profiles. The traffic is sent and the statistics obtained using API
:command:`trex.stl.api.STLClient`.
Measuring Packet Loss
If measurement of latency is requested, two more packet streams are
created (one for each direction) with TRex flow_stats parameter set to
STLFlowLatencyStats. In that case, returned statistics will also include
-min/avg/max latency values and encoded HDRHstogram data.
+min/avg/max latency values and encoded HDRHistogram data.
#. NIC-1: x710-DA4 4p10GE Intel.
#. NIC-2: xxv710-DA2 2p25GE Intel.
-#. NIC-3: cx556a-edat ConnectX5 2p100GE Mellanox. (Only testbed t27, t28)
+#. NIC-3: cx556a-edat ConnectX5 2p100GE Mellanox.
#. NIC-4: empty, future expansion.
#. NIC-5: empty, future expansion.
#. NIC-6: empty, future expansion.
#. NIC-1: x710-DA4 4p10GE Intel.
#. NIC-2: xxv710-DA2 2p25GE Intel.
-#. NIC-3: cx556a-edat ConnectX5 2p100GE Mellanox. (Only testbed t27, t28)
+#. NIC-3: cx556a-edat ConnectX5 2p100GE Mellanox.
#. NIC-4: empty, future expansion.
#. NIC-5: empty, future expansion.
#. NIC-6: x710-DA4 4p10GE Intel. (For self-tests.)
#. NIC-1: x710-DA4 4p10GE Intel.
#. NIC-2: xxv710-DA2 2p25GE Intel.
-#. NIC-3: cx556a-edat ConnectX5 2p100GE Mellanox. (Not used yet.)
+#. NIC-3: empty, future expansion.
#. NIC-4: empty, future expansion.
#. NIC-5: empty, future expansion.
#. NIC-6: empty, future expansion.
#. NIC-1: x710-DA4 4p10GE Intel.
#. NIC-2: xxv710-DA2 2p25GE Intel.
-#. NIC-3: cx556a-edat ConnectX5 2p100GE Mellanox. (Not used yet.)
+#. NIC-3: empty, future expansion.
#. NIC-4: empty, future expansion.
#. NIC-5: empty, future expansion.
#. NIC-6: x710-DA4 4p10GE Intel. (For self-tests.)
Below a subset of the running configuration:
-1. Ubuntu 18.04.x LTS
+1. Ubuntu 18.04.2 LTS
::
$ lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
- Description: Ubuntu 18.04.3 LTS
+ Description: Ubuntu 18.04.2 LTS
Release: 18.04
Codename: bionic
Hugepages Configuration
~~~~~~~~~~~~~~~~~~~~~~~
-Huge pages are namaged via sysctl configuration located in
+Huge pages are managed via sysctl configuration located in
`/etc/sysctl.d/90-csit.conf` on each testbed. Default huge page size is 2M.
The exact amount of huge pages depends on testbed. All the values are defined
in `Ansible inventory - hosts` files.
DPDK v19.05
-TG Build Script Used
-~~~~~~~~~~~~~~~~~~~~
+TG Installation
+~~~~~~~~~~~~~~~
-`TRex installation`_
+T-Rex installation is managed via Ansible role.
TG Startup Configuration
~~~~~~~~~~~~~~~~~~~~~~~~
::
- $ cat /etc/trex_cfg.yaml
- - version : 2
- interfaces : ["0000:0d:00.0","0000:0d:00.1"]
- port_info :
- - dest_mac : [0x3c,0xfd,0xfe,0x9c,0xee,0xf5]
- src_mac : [0x3c,0xfd,0xfe,0x9c,0xee,0xf4]
- - dest_mac : [0x3c,0xfd,0xfe,0x9c,0xee,0xf4]
- src_mac : [0x3c,0xfd,0xfe,0x9c,0xee,0xf5]
+ $ sudo -E -S sh -c 'cat << EOF > /etc/trex_cfg.yaml
+ - version: 2
+ c: 15
+ limit_memory: 8192
+ interfaces: ["${pci1}","${pci2}"]
+ port_info:
+ - dest_mac: [${dest_mac1}]
+ src_mac: [${src_mac1}]
+ - dest_mac: [${dest_mac2}]
+ src_mac: [${src_mac2}]
+ platform :
+ master_thread_id: 0
+ latency_thread_id: 16
+ dual_if:
+ - socket: 0
+ threads: [1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15]
+ EOF'
TG Startup Command
~~~~~~~~~~~~~~~~~~
::
- $ sh -c 'cd <t-rex-install-dir>/scripts/ && sudo nohup ./t-rex-64 -i -c 7 --prefix $(hostname) --hdrh > /tmp/trex.log 2>&1 &'> /dev/null
+ $ sh -c 'cd <t-rex-install-dir>/scripts/ && \
+ sudo nohup ./t-rex-64 -i --prefix $(hostname) --hdrh --no-scapy-server \
+ > /tmp/trex.log 2>&1 &' > /dev/null
TG API Driver
~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~~~~
VPP startup configuration vary per test case, with different settings
-for `$$CORELIST_WORKERS`, `$$NUM_RX_QUEUES`, `$$UIO_DRIVER`, `$$NUM-
-MBUFS` and `$$NO_MULTI_SEG` parameter. Default template is provided
-below:
+for `$$CORELIST_WORKERS`, `$$NUM_RX_QUEUES`, `$$UIO_DRIVER`, and
+`$$NO_MULTI_SEG` parameter. List of plugins to enable is driven by test
+requirements. Default template is provided below:
::
statseg
{
size 4G
+ per-node-counters on
}
unix
{
cli-listen /run/vpp/cli.sock
log /tmp/vpe.log
nodaemon
+ full-coredump
}
socksvr {
socket-name /run/vpp/api.sock
{
disable
}
- plugin dpdk_plugin.so
+ plugin <$$test_requirement>_plugin.so
{
enable
}
corelist-workers $$CORELIST_WORKERS
main-core 1
}
+ buffers
+ {
+ buffers-per-numa 215040
+ }
+
+ # Below: in case of dpdk based drivers (vfio-pci) only
dpdk
{
- num-mbufs $$NUM-MBUFS
uio-driver $$UIO_DRIVER
$$NO_MULTI_SEG
log-level debug
.. _pdf version of this report: https://docs.fd.io/csit/{release}/report/_static/archive/csit_{release}.{report_week}.pdf
.. _tag documentation rst file: https://git.fd.io/csit/tree/docs/tag_documentation.rst?h={release}
-.. _TRex installation: https://git.fd.io/csit/tree/resources/tools/trex/trex_installer.sh?h={release}
.. _TRex driver: https://git.fd.io/csit/tree/resources/tools/trex/trex_stateless_profile.py?h={release}
.. _CSIT DPDK Performance Tests Documentation: https://docs.fd.io/csit/{release}/doc/tests.dpdk.perf.html
.. _CSIT VPP Performance Tests Documentation: https://docs.fd.io/csit/{release}/doc/tests.vpp.perf.html
.. _FD.io VPP compile job: https://jenkins.fd.io/view/vpp/job/vpp-merge-{srelease}-ubuntu1804/
.. _CSIT Testbed Setup: https://git.fd.io/csit/tree/resources/tools/testbed-setup/README.md?h={release}
.. _VPP startup.conf: https://git.fd.io/vpp/tree/src/vpp/conf/startup.conf?h=stable/{srelease}&id={vpp_release_commit_id}
-""".format(release=u'rls2001',
+""".format(release=u'rls2005',
report_week=report_week,
- prev_release=u'rls1908',
- srelease=u'2001',
- csitrelease=u'2001',
- csit_prev_release=u'1908',
- vpprelease=u'20.01',
- vpp_prev_release=u'19.08',
- dpdkrelease=u'19.08',
- dpdk_prev_release=u'19.05',
- sdpdkrelease=u'1908',
+ prev_release=u'rls2001',
+ srelease=u'2005',
+ csitrelease=u'2005',
+ csit_prev_release=u'2001',
+ vpprelease=u'20.05',
+ vpp_prev_release=u'20.01',
+ dpdkrelease=u'20.02',
+ dpdk_prev_release=u'19.08',
+ sdpdkrelease=u'2002',
trex_version=u'v2.73',
vpp_release_commit_id=u'fce396738f865293f0a023bc7f172086f81da456')
Code Review / csit.git / commitdiff