- SR-IOV VF
- Hot plug
- IEEE1588/802.1AS timestamping
+- VF Daemon (VFD) - EXPERIMENTAL
Prerequisites
Toggle the use of Vector PMD instead of normal RX/TX path.
To enable vPMD for RX, bulk allocation for Rx must be allowed.
-- ``CONFIG_RTE_LIBRTE_I40E_RX_OLFLAGS_ENABLE`` (default ``y``)
-
- Toggle to enable RX ``olflags``.
- This is only meaningful when Vector PMD is used.
-
- ``CONFIG_RTE_LIBRTE_I40E_16BYTE_RX_DESC`` (default ``n``)
Toggle to use a 16-byte RX descriptor, by default the RX descriptor is 32 byte.
Interrupt Throttling interval.
-Driver Compilation
-~~~~~~~~~~~~~~~~~~
-
-To compile the I40E PMD see :ref:`Getting Started Guide for Linux <linux_gsg>` or
-:ref:`Getting Started Guide for FreeBSD <freebsd_gsg>` depending on your platform.
-
-
-Linux
------
-
-
-Running testpmd
-~~~~~~~~~~~~~~~
-
-This section demonstrates how to launch ``testpmd`` with Intel XL710/X710
-devices managed by ``librte_pmd_i40e`` in the Linux operating system.
-
-#. Load ``igb_uio`` or ``vfio-pci`` driver:
-
- .. code-block:: console
-
- modprobe uio
- insmod ./x86_64-native-linuxapp-gcc/kmod/igb_uio.ko
-
- or
-
- .. code-block:: console
-
- modprobe vfio-pci
-
-#. Bind the XL710/X710 adapters to ``igb_uio`` or ``vfio-pci`` loaded in the previous step:
-
- .. code-block:: console
-
- ./tools/dpdk-devbind.py --bind igb_uio 0000:83:00.0
-
- Or setup VFIO permissions for regular users and then bind to ``vfio-pci``:
-
- .. code-block:: console
-
- ./tools/dpdk-devbind.py --bind vfio-pci 0000:83:00.0
-
-#. Start ``testpmd`` with basic parameters:
-
- .. code-block:: console
-
- ./x86_64-native-linuxapp-gcc/app/testpmd -c 0xf -n 4 -w 83:00.0 -- -i
-
- Example output:
-
- .. code-block:: console
-
- ...
- EAL: PCI device 0000:83:00.0 on NUMA socket 1
- EAL: probe driver: 8086:1572 rte_i40e_pmd
- EAL: PCI memory mapped at 0x7f7f80000000
- EAL: PCI memory mapped at 0x7f7f80800000
- PMD: eth_i40e_dev_init(): FW 5.0 API 1.5 NVM 05.00.02 eetrack 8000208a
- Interactive-mode selected
- Configuring Port 0 (socket 0)
- ...
-
- PMD: i40e_dev_rx_queue_setup(): Rx Burst Bulk Alloc Preconditions are
- satisfied.Rx Burst Bulk Alloc function will be used on port=0, queue=0.
-
- ...
- Port 0: 68:05:CA:26:85:84
- Checking link statuses...
- Port 0 Link Up - speed 10000 Mbps - full-duplex
- Done
+Driver compilation and testing
+------------------------------
- testpmd>
+Refer to the document :ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`
+for details.
SR-IOV: Prerequisites and sample Application Notes
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+--------------------------------------------------
#. Load the kernel module:
#. Assign VF to VM, and bring up the VM.
Please see the documentation for the *I40E/IXGBE/IGB Virtual Function Driver*.
+#. Running testpmd:
+
+ Follow instructions available in the document
+ :ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`
+ to run testpmd.
+
+ Example output:
+
+ .. code-block:: console
+
+ ...
+ EAL: PCI device 0000:83:00.0 on NUMA socket 1
+ EAL: probe driver: 8086:1572 rte_i40e_pmd
+ EAL: PCI memory mapped at 0x7f7f80000000
+ EAL: PCI memory mapped at 0x7f7f80800000
+ PMD: eth_i40e_dev_init(): FW 5.0 API 1.5 NVM 05.00.02 eetrack 8000208a
+ Interactive-mode selected
+ Configuring Port 0 (socket 0)
+ ...
+
+ PMD: i40e_dev_rx_queue_setup(): Rx Burst Bulk Alloc Preconditions are
+ satisfied.Rx Burst Bulk Alloc function will be used on port=0, queue=0.
+
+ ...
+ Port 0: 68:05:CA:26:85:84
+ Checking link statuses...
+ Port 0 Link Up - speed 10000 Mbps - full-duplex
+ Done
+
+ testpmd>
+
Sample Application Notes
------------------------
.. code-block:: console
- ./app/testpmd -c ffff -n 4 -- -i --forward-mode=mac
+ ./app/testpmd -l 0-15 -n 4 -- -i --forward-mode=mac
...
testpmd> set promisc 0 off
.. code-block:: console
- ./app/testpmd -c ffff -n 4 -- -i --disable-rss --pkt-filter-mode=perfect \
+ ./app/testpmd -l 0-15 -n 4 -- -i --disable-rss --pkt-filter-mode=perfect \
--rxq=8 --txq=8 --nb-cores=8 --nb-ports=1
Add a rule to direct ``ipv4-udp`` packet whose ``dst_ip=2.2.2.5, src_ip=2.2.2.3, src_port=32, dst_port=32`` to queue 1:
is to say, user should keep ``CONFIG_RTE_LIBRTE_I40E_16BYTE_RX_DESC=n`` in
config file.
-Link down with i40e kernel driver after DPDK application exist
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+Link down with i40e kernel driver after DPDK application exit
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
After DPDK application quit, and the device is bound back to Linux i40e
kernel driver, the link cannot be up after ``ifconfig <dev> up``.
Due to the FW limitation, PF can receive packets with Ethertype 0x88A8
only when floating VEB is disabled.
+
+Incorrect Rx statistics when packet is oversize
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+When a packet is over maximum frame size, the packet is dropped.
+However the Rx statistics, when calling `rte_eth_stats_get` incorrectly
+shows it as received.
+
+VF & TC max bandwidth setting
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The per VF max bandwidth and per TC max bandwidth cannot be enabled in parallel.
+The dehavior is different when handling per VF and per TC max bandwidth setting.
+When enabling per VF max bandwidth, SW will check if per TC max bandwidth is
+enabled. If so, return failure.
+When enabling per TC max bandwidth, SW will check if per VF max bandwidth
+is enabled. If so, disable per VF max bandwidth and continue with per TC max
+bandwidth setting.
+
+TC TX scheduling mode setting
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+There're 2 TX scheduling modes for TCs, round robin and strict priority mode.
+If a TC is set to strict priority mode, it can consume unlimited bandwidth.
+It means if APP has set the max bandwidth for that TC, it comes to no
+effect.
+It's suggested to set the strict priority mode for a TC that is latency
+sensitive but no consuming much bandwidth.
Code Review / deb_dpdk.git / blobdiff