.. BSD LICENSE
Copyright 2012-2015 6WIND S.A.
+ Copyright 2015 Mellanox
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
Features
--------
+- Multi arch support: x86_64 and POWER8.
- RSS, also known as RCA, is supported. In this mode the number of
configured RX queues must be a power of two.
- VLAN filtering is supported.
- Inner L3/L4 (IP, TCP and UDP) TX/RX checksum offloading and validation.
- Outer L3 (IP) TX/RX checksum offloading and validation for VXLAN frames.
- Secondary process TX is supported.
+- RX interrupts.
Limitations
-----------
adds additional run-time checks and debugging messages at the cost of
lower performance.
+- ``CONFIG_RTE_LIBRTE_MLX4_DEBUG_BROKEN_VERBS`` (default **n**)
+
+ Mellanox OFED versions earlier than 4.2 may return false errors from
+ Verbs object destruction APIs after the device is plugged out.
+ Enabling this option replaces assertion checks that cause the program
+ to abort with harmless debugging messages as a workaround.
+ Relevant only when CONFIG_RTE_LIBRTE_MLX4_DEBUG is enabled.
+
- ``CONFIG_RTE_LIBRTE_MLX4_SGE_WR_N`` (default **4**)
Number of scatter/gather elements (SGEs) per work request (WR). Lowering
Currently supported by DPDK:
-- Mellanox OFED **4.0-2.0.0.0**.
-- Firmware version **2.40.7000**.
-- Supported architectures: **x86_64** and **POWER8**.
+- Mellanox OFED **4.1**.
+- Firmware version **2.36.5000** and above.
Getting Mellanox OFED
~~~~~~~~~~~~~~~~~~~~~
* Mellanox(R) ConnectX(R)-3 Pro 40G MCX354A-FCC_Ax (2*40G)
+Quick Start Guide
+-----------------
+
+1. Download latest Mellanox OFED. For more info check the `prerequisites`_.
+
+2. Install the required libraries and kernel modules either by installing
+ only the required set, or by installing the entire Mellanox OFED:
+
+ For bare metal use:
+
+ .. code-block:: console
+
+ ./mlnxofedinstall
+
+ For SR-IOV hypervisors use:
+
+ .. code-block:: console
+
+ ./mlnxofedinstall --enable-sriov -hypervisor
+
+ For SR-IOV virtual machine use:
+
+ .. code-block:: console
+
+ ./mlnxofedinstall --guest
+
+3. Verify the firmware is the correct one:
+
+ .. code-block:: console
+
+ ibv_devinfo
+
+4. Set all ports links to Ethernet, follow instructions on the screen:
+
+ .. code-block:: console
+
+ connectx_port_config
+
+ Or in the manual way:
+
+ .. code-block:: console
+
+ PCI=<NIC PCI address>
+ echo eth > "/sys/bus/pci/devices/$PCI/mlx4_port0"
+ echo eth > "/sys/bus/pci/devices/$PCI/mlx4_port1"
+
+5. In case of bare metal or hypervisor, configure optimized steering mode
+ by adding the following line to ``/etc/modprobe.d/mlx4_core.conf``:
+
+ .. code-block:: console
+
+ options mlx4_core log_num_mgm_entry_size=-7
+
+ .. note::
+
+ If VLAN filtering is used, set log_num_mgm_entry_size=-1.
+ Performance degradation can occur on this case.
+
+6. Restart the driver:
+
+ .. code-block:: console
+
+ /etc/init.d/openibd restart
+
+ or:
+
+ .. code-block:: console
+
+ service openibd restart
+
+7. Compile DPDK and you are ready to go. See instructions on
+ :ref:`Development Kit Build System <Development_Kit_Build_System>`
+
+Performance tuning
+------------------
+
+1. Verify the optimized steering mode is configured:
+
+ .. code-block:: console
+
+ cat /sys/module/mlx4_core/parameters/log_num_mgm_entry_size
+
+2. Use environment variable MLX4_INLINE_RECV_SIZE=64 to get maximum
+ performance for 64B messages.
+
+3. Use the CPU near local NUMA node to which the PCIe adapter is connected,
+ for better performance. For VMs, verify that the right CPU
+ and NUMA node are pinned according to the above. Run:
+
+ .. code-block:: console
+
+ lstopo-no-graphics
+
+ to identify the NUMA node to which the PCIe adapter is connected.
+
+4. If more than one adapter is used, and root complex capabilities allow
+ to put both adapters on the same NUMA node without PCI bandwidth degradation,
+ it is recommended to locate both adapters on the same NUMA node.
+ This in order to forward packets from one to the other without
+ NUMA performance penalty.
+
+5. Disable pause frames:
+
+ .. code-block:: console
+
+ ethtool -A <netdev> rx off tx off
+
+6. Verify IO non-posted prefetch is disabled by default. This can be checked
+ via the BIOS configuration. Please contact you server provider for more
+ information about the settings.
+
+.. note::
+
+ On some machines, depends on the machine integrator, it is beneficial
+ to set the PCI max read request parameter to 1K. This can be
+ done in the following way:
+
+ To query the read request size use:
+
+ .. code-block:: console
+
+ setpci -s <NIC PCI address> 68.w
+
+ If the output is different than 3XXX, set it by:
+
+ .. code-block:: console
+
+ setpci -s <NIC PCI address> 68.w=3XXX
+
+ The XXX can be different on different systems. Make sure to configure
+ according to the setpci output.
+
Usage example
-------------
Code Review / deb_dpdk.git / blobdiff