--- /dev/null
+.. BSD LICENSE
+ Copyright (c) 2016 Solarflare Communications Inc.
+ All rights reserved.
+
+ This software was jointly developed between OKTET Labs (under contract
+ for Solarflare) and Solarflare Communications, Inc.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions are met:
+
+ 1. Redistributions of source code must retain the above copyright notice,
+ this list of conditions and the following disclaimer.
+ 2. Redistributions in binary form must reproduce the above copyright notice,
+ this list of conditions and the following disclaimer in the documentation
+ and/or other materials provided with the distribution.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
+ THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
+ PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
+ CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
+ EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
+ PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
+ OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
+ OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
+ EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+
+Solarflare libefx-based Poll Mode Driver
+========================================
+
+The SFC EFX PMD (**librte_pmd_sfc_efx**) provides poll mode driver support
+for **Solarflare SFN7xxx and SFN8xxx** family of 10/40 Gbps adapters.
+SFC EFX PMD has support for the latest Linux and FreeBSD operating systems.
+
+More information can be found at `Solarflare Communications website
+<http://solarflare.com>`_.
+
+
+Features
+--------
+
+SFC EFX PMD has support for:
+
+- Multiple transmit and receive queues
+
+- Link state information including link status change interrupt
+
+- IPv4/IPv6 TCP/UDP transmit checksum offload
+
+- Port hardware statistics
+
+- Extended statistics (see Solarflare Server Adapter User's Guide for
+ the statistics description)
+
+- Basic flow control
+
+- MTU update
+
+- Jumbo frames up to 9K
+
+- Promiscuous mode
+
+- Allmulticast mode
+
+- TCP segmentation offload (TSO)
+
+- Multicast MAC filter
+
+- IPv4/IPv6 TCP/UDP receive checksum offload
+
+- Received packet type information
+
+- Receive side scaling (RSS)
+
+- RSS hash
+
+- Scattered Rx DMA for packet that are larger that a single Rx descriptor
+
+- Deferred receive and transmit queue start
+
+- Transmit VLAN insertion (if running firmware variant supports it)
+
+- Flow API
+
+
+Non-supported Features
+----------------------
+
+The features not yet supported include:
+
+- Receive queue interupts
+
+- Priority-based flow control
+
+- Loopback
+
+- Configurable RX CRC stripping (always stripped)
+
+- Header split on receive
+
+- VLAN filtering
+
+- VLAN stripping
+
+- LRO
+
+
+Limitations
+-----------
+
+Due to requirements on receive buffer alignment and usage of the receive
+buffer for the auxiliary packet information provided by the NIC up to
+extra 269 (14 bytes prefix plus up to 255 bytes for end padding) bytes may be
+required in the receive buffer.
+It should be taken into account when mbuf pool for receive is created.
+
+
+Flow API support
+----------------
+
+Supported attributes:
+
+- Ingress
+
+Supported pattern items:
+
+- VOID
+
+- ETH (exact match of source/destination addresses, individual/group match
+ of destination address, EtherType)
+
+- VLAN (exact match of VID, double-tagging is supported)
+
+- IPV4 (exact match of source/destination addresses,
+ IP transport protocol)
+
+- IPV6 (exact match of source/destination addresses,
+ IP transport protocol)
+
+- TCP (exact match of source/destination ports)
+
+- UDP (exact match of source/destination ports)
+
+Supported actions:
+
+- VOID
+
+- QUEUE
+
+Validating flow rules depends on the firmware variant.
+
+Ethernet destinaton individual/group match
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Ethernet item supports I/G matching, if only the corresponding bit is set
+in the mask of destination address. If destinaton address in the spec is
+multicast, it matches all multicast (and broadcast) packets, oherwise it
+matches unicast packets that are not filtered by other flow rules.
+
+
+Supported NICs
+--------------
+
+- Solarflare Flareon [Ultra] Server Adapters:
+
+ - Solarflare SFN8522 Dual Port SFP+ Server Adapter
+
+ - Solarflare SFN8542 Dual Port QSFP+ Server Adapter
+
+ - Solarflare SFN7002F Dual Port SFP+ Server Adapter
+
+ - Solarflare SFN7004F Quad Port SFP+ Server Adapter
+
+ - Solarflare SFN7042Q Dual Port QSFP+ Server Adapter
+
+ - Solarflare SFN7122F Dual Port SFP+ Server Adapter
+
+ - Solarflare SFN7124F Quad Port SFP+ Server Adapter
+
+ - Solarflare SFN7142Q Dual Port QSFP+ Server Adapter
+
+ - Solarflare SFN7322F Precision Time Synchronization Server Adapter
+
+
+Prerequisites
+-------------
+
+- Requires firmware version:
+
+ - SFN7xxx: **4.7.1.1001** or higher
+
+ - SFN8xxx: **6.0.2.1004** or higher
+
+Visit `Solarflare Support Downloads <https://support.solarflare.com>`_ to get
+Solarflare Utilities (either Linux or FreeBSD) with the latest firmware.
+Follow instructions from Solarflare Server Adapter User's Guide to
+update firmware and configure the adapter.
+
+
+Pre-Installation Configuration
+------------------------------
+
+
+Config File Options
+~~~~~~~~~~~~~~~~~~~
+
+The following options can be modified in the ``.config`` file.
+Please note that enabling debugging options may affect system performance.
+
+- ``CONFIG_RTE_LIBRTE_SFC_EFX_PMD`` (default **y**)
+
+ Enable compilation of Solarflare libefx-based poll-mode driver.
+
+- ``CONFIG_RTE_LIBRTE_SFC_EFX_DEBUG`` (default **n**)
+
+ Enable compilation of the extra run-time consistency checks.
+
+
+Per-Device Parameters
+~~~~~~~~~~~~~~~~~~~~~
+
+The following per-device parameters can be passed via EAL PCI device
+whitelist option like "-w 02:00.0,arg1=value1,...".
+
+Case-insensitive 1/y/yes/on or 0/n/no/off may be used to specify
+boolean parameters value.
+
+- ``rx_datapath`` [auto|efx|ef10] (default **auto**)
+
+ Choose receive datapath implementation.
+ **auto** allows the driver itself to make a choice based on firmware
+ features available and required by the datapath implementation.
+ **efx** chooses libefx-based datapath which supports Rx scatter.
+ **ef10** chooses EF10 (SFN7xxx, SFN8xxx) native datapath which is
+ more efficient than libefx-based and provides richer packet type
+ classification, but lacks Rx scatter support.
+
+- ``tx_datapath`` [auto|efx|ef10|ef10_simple] (default **auto**)
+
+ Choose transmit datapath implementation.
+ **auto** allows the driver itself to make a choice based on firmware
+ features available and required by the datapath implementation.
+ **efx** chooses libefx-based datapath which supports VLAN insertion
+ (full-feature firmware variant only), TSO and multi-segment mbufs.
+ **ef10** chooses EF10 (SFN7xxx, SFN8xxx) native datapath which is
+ more efficient than libefx-based but has no VLAN insertion and TSO
+ support yet.
+ **ef10_simple** chooses EF10 (SFN7xxx, SFN8xxx) native datapath which
+ is even more faster then **ef10** but does not support multi-segment
+ mbufs.
+
+- ``perf_profile`` [auto|throughput|low-latency] (default **throughput**)
+
+ Choose hardware tunning to be optimized for either throughput or
+ low-latency.
+ **auto** allows NIC firmware to make a choice based on
+ installed licences and firmware variant configured using **sfboot**.
+
+- ``debug_init`` [bool] (default **n**)
+
+ Enable extra logging during device intialization and startup.
+
+- ``mcdi_logging`` [bool] (default **n**)
+
+ Enable extra logging of the communication with the NIC's management CPU.
+ The logging is done using RTE_LOG() with INFO level and PMD type.
+ The format is consumed by the Solarflare netlogdecode cross-platform tool.
+
+- ``stats_update_period_ms`` [long] (default **1000**)
+
+ Adjust period in milliseconds to update port hardware statistics.
+ The accepted range is 0 to 65535. The value of **0** may be used
+ to disable periodic statistics update. One should note that it's
+ only possible to set an arbitrary value on SFN8xxx provided that
+ firmware version is 6.2.1.1033 or higher, otherwise any positive
+ value will select a fixed update period of **1000** milliseconds
Code Review / deb_dpdk.git / blobdiff