-.. BSD LICENSE
- Copyright(c) 2017 Intel Corporation. All rights reserved.
-
- Redistribution and use in source and binary forms, with or without
- modification, are permitted provided that the following conditions
- are met:
-
- * Redistributions of source code must retain the above copyright
- notice, this list of conditions and the following disclaimer.
- * Redistributions in binary form must reproduce the above copyright
- notice, this list of conditions and the following disclaimer in
- the documentation and/or other materials provided with the
- distribution.
- * Neither the name of Intel Corporation nor the names of its
- contributors may be used to endorse or promote products derived
- from this software without specific prior written permission.
-
- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+.. SPDX-License-Identifier: BSD-3-Clause
+ Copyright(c) 2017 Intel Corporation.
+ Copyright(c) 2018 Arm Limited.
Event Device Library
====================
This section will introduce the reader to the eventdev API, showing how to
create and configure an eventdev and use it for a two-stage atomic pipeline
-with a single core for TX. The diagram below shows the final state of the
-application after this walk-through:
+with one core each for RX and TX. RX and TX cores are shown here for
+illustration, refer to Eventdev Adapter documentation for further details.
+The diagram below shows the final state of the application after this
+walk-through:
.. _figure_eventdev-usage1:
.nb_atomic_flows = 1024,
.nb_atomic_order_sequences = 1024,
};
+ struct rte_event_queue_conf single_link_conf = {
+ .event_queue_cfg = RTE_EVENT_QUEUE_CFG_SINGLE_LINK,
+ };
int dev_id = 0;
- int queue_id = 0;
- int err = rte_event_queue_setup(dev_id, queue_id, &atomic_conf);
+ int atomic_q_1 = 0;
+ int atomic_q_2 = 1;
+ int single_link_q = 2;
+ int err = rte_event_queue_setup(dev_id, atomic_q_1, &atomic_conf);
+ int err = rte_event_queue_setup(dev_id, atomic_q_2, &atomic_conf);
+ int err = rte_event_queue_setup(dev_id, single_link_q, &single_link_conf);
-The remainder of this walk-through assumes that the queues are configured as
-follows:
+As shown above, queue IDs are as follows:
* id 0, atomic queue #1
* id 1, atomic queue #2
* id 2, single-link queue
+These queues are used for the remainder of this walk-through.
+
Setting up Ports
~~~~~~~~~~~~~~~~
-Once queues are set up successfully, create the ports as required. Each port
-should be set up with its corresponding port_conf type, worker for worker cores,
-rx and tx for the RX and TX cores:
+Once queues are set up successfully, create the ports as required.
.. code-block:: c
.new_event_threshold = 4096,
};
int dev_id = 0;
- int port_id = 0;
- int err = rte_event_port_setup(dev_id, port_id, &CORE_FUNCTION_conf);
+ int rx_port_id = 0;
+ int err = rte_event_port_setup(dev_id, rx_port_id, &rx_conf);
+
+ for(int worker_port_id = 1; worker_port_id <= 4; worker_port_id++) {
+ int err = rte_event_port_setup(dev_id, worker_port_id, &worker_conf);
+ }
-It is now assumed that:
+ int tx_port_id = 5;
+ int err = rte_event_port_setup(dev_id, tx_port_id, &tx_conf);
+
+As shown above:
* port 0: RX core
* ports 1,2,3,4: Workers
* port 5: TX core
+These ports are used for the remainder of this walk-through.
+
Linking Queues and Ports
~~~~~~~~~~~~~~~~~~~~~~~~
.. code-block:: c
- uint8_t port_id = 0;
+ uint8_t rx_port_id = 0;
+ uint8_t tx_port_id = 5;
uint8_t atomic_qs[] = {0, 1};
uint8_t single_link_q = 2;
- uint8_t tx_port_id = 5;
uin8t_t priority = RTE_EVENT_DEV_PRIORITY_NORMAL;
- for(int i = 0; i < 4; i++) {
- int worker_port = i + 1;
- int links_made = rte_event_port_link(dev_id, worker_port, atomic_qs, NULL, 2);
+ for(int worker_port_id = 1; worker_port_id <= 4; worker_port_id++) {
+ int links_made = rte_event_port_link(dev_id, worker_port_id, atomic_qs, NULL, 2);
}
int links_made = rte_event_port_link(dev_id, tx_port_id, &single_link_q, &priority, 1);
ev[i].flow_id = mbufs[i]->hash.rss;
ev[i].op = RTE_EVENT_OP_NEW;
ev[i].sched_type = RTE_SCHED_TYPE_ATOMIC;
- ev[i].queue_id = 0;
+ ev[i].queue_id = atomic_q_1;
ev[i].event_type = RTE_EVENT_TYPE_ETHDEV;
ev[i].sub_event_type = 0;
ev[i].priority = RTE_EVENT_DEV_PRIORITY_NORMAL;
ev[i].mbuf = mbufs[i];
}
- const int nb_tx = rte_event_enqueue_burst(dev_id, port_id, ev, nb_rx);
+ const int nb_tx = rte_event_enqueue_burst(dev_id, rx_port_id, ev, nb_rx);
if (nb_tx != nb_rx) {
for(i = nb_tx; i < nb_rx; i++)
rte_pktmbuf_free(mbufs[i]);
events[i].queue_id++;
}
- uint16_t nb_tx = rte_event_enqueue_burst(dev_id, port_id, events, nb_rx);
+ uint16_t nb_tx = rte_event_enqueue_burst(dev_id, worker_port_id, events, nb_rx);
Egress of Events
Code Review / deb_dpdk.git / blobdiff