--- /dev/null
+/*-
+ * BSD LICENSE
+ *
+ * Copyright(c) Broadcom Limited.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef _HSI_STRUCT_DEF_EXTERNAL_H_
+#define _HSI_STRUCT_DEF_EXTERNAL_H_
+
+/*
+ * per-context HW statistics -- chip view
+ */
+
+struct ctx_hw_stats64 {
+ uint64_t rx_ucast_pkts;
+ uint64_t rx_mcast_pkts;
+ uint64_t rx_bcast_pkts;
+ uint64_t rx_drop_pkts;
+ uint64_t rx_err_pkts;
+ uint64_t rx_ucast_bytes;
+ uint64_t rx_mcast_bytes;
+ uint64_t rx_bcast_bytes;
+
+ uint64_t tx_ucast_pkts;
+ uint64_t tx_mcast_pkts;
+ uint64_t tx_bcast_pkts;
+ uint64_t tx_drop_pkts;
+ uint64_t tx_err_pkts;
+ uint64_t tx_ucast_bytes;
+ uint64_t tx_mcast_bytes;
+ uint64_t tx_bcast_bytes;
+
+ uint64_t tpa_pkts;
+ uint64_t tpa_bytes;
+ uint64_t tpa_events;
+ uint64_t tpa_aborts;
+} ctx_hw_stats64_t;
+
+/* HW Resource Manager Specification 1.2.0 */
+#define HWRM_VERSION_MAJOR 1
+#define HWRM_VERSION_MINOR 2
+#define HWRM_VERSION_UPDATE 0
+
+/*
+ * Following is the signature for HWRM message field that indicates not
+ * applicable (All F's). Need to cast it the size of the field if needed.
+ */
+#define HWRM_NA_SIGNATURE ((uint32_t)(-1))
+#define HWRM_MAX_REQ_LEN (128) /* hwrm_func_buf_rgtr */
+#define HWRM_MAX_RESP_LEN (176) /* hwrm_func_qstats */
+#define HW_HASH_INDEX_SIZE 0x80 /* 7 bit indirection table index. */
+#define HW_HASH_KEY_SIZE 40
+#define HWRM_RESP_VALID_KEY 1 /* valid key for HWRM response */
+
+/*
+ * Request types
+ */
+#define HWRM_VER_GET (UINT32_C(0x0))
+#define HWRM_FUNC_RESET (UINT32_C(0x11))
+#define HWRM_FUNC_QCAPS (UINT32_C(0x15))
+#define HWRM_FUNC_DRV_UNRGTR (UINT32_C(0x1a))
+#define HWRM_FUNC_DRV_RGTR (UINT32_C(0x1d))
+#define HWRM_PORT_PHY_CFG (UINT32_C(0x20))
+#define HWRM_PORT_PHY_QCFG (UINT32_C(0x27))
+#define HWRM_QUEUE_QPORTCFG (UINT32_C(0x30))
+#define HWRM_VNIC_ALLOC (UINT32_C(0x40))
+#define HWRM_VNIC_FREE (UINT32_C(0x41))
+#define HWRM_VNIC_CFG (UINT32_C(0x42))
+#define HWRM_VNIC_RSS_CFG (UINT32_C(0x46))
+#define HWRM_RING_ALLOC (UINT32_C(0x50))
+#define HWRM_RING_FREE (UINT32_C(0x51))
+#define HWRM_RING_GRP_ALLOC (UINT32_C(0x60))
+#define HWRM_RING_GRP_FREE (UINT32_C(0x61))
+#define HWRM_VNIC_RSS_COS_LB_CTX_ALLOC (UINT32_C(0x70))
+#define HWRM_VNIC_RSS_COS_LB_CTX_FREE (UINT32_C(0x71))
+#define HWRM_CFA_L2_FILTER_ALLOC (UINT32_C(0x90))
+#define HWRM_CFA_L2_FILTER_FREE (UINT32_C(0x91))
+#define HWRM_CFA_L2_FILTER_CFG (UINT32_C(0x92))
+#define HWRM_CFA_L2_SET_RX_MASK (UINT32_C(0x93))
+#define HWRM_STAT_CTX_ALLOC (UINT32_C(0xb0))
+#define HWRM_STAT_CTX_FREE (UINT32_C(0xb1))
+#define HWRM_STAT_CTX_CLR_STATS (UINT32_C(0xb3))
+#define HWRM_EXEC_FWD_RESP (UINT32_C(0xd0))
+
+/* Return Codes */
+#define HWRM_ERR_CODE_INVALID_PARAMS (UINT32_C(0x2))
+#define HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED (UINT32_C(0x3))
+
+/* Short TX BD (16 bytes) */
+struct tx_bd_short {
+ /*
+ * All bits in this field must be valid on the first BD of a packet.
+ * Only the packet_end bit must be valid for the remaining BDs of a
+ * packet.
+ */
+ /* This value identifies the type of buffer descriptor. */
+ #define TX_BD_SHORT_TYPE_MASK UINT32_C(0x3f)
+ #define TX_BD_SHORT_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 16B long and is used for normal L2
+ * packet transmission.
+ */
+ #define TX_BD_SHORT_TYPE_TX_BD_SHORT (UINT32_C(0x0) << 0)
+ /*
+ * If set to 1, the packet ends with the data in the buffer pointed to
+ * by this descriptor. This flag must be valid on every BD.
+ */
+ #define TX_BD_SHORT_FLAGS_PACKET_END UINT32_C(0x40)
+ /*
+ * If set to 1, the device will not generate a completion for this
+ * transmit packet unless there is an error in it's processing. If this
+ * bit is set to 0, then the packet will be completed normally. This bit
+ * must be valid only on the first BD of a packet.
+ */
+ #define TX_BD_SHORT_FLAGS_NO_CMPL UINT32_C(0x80)
+ /*
+ * This value indicates how many 16B BD locations are consumed in the
+ * ring by this packet. A value of 1 indicates that this BD is the only
+ * BD (and that the it is a short BD). A value of 3 indicates either 3
+ * short BDs or 1 long BD and one short BD in the packet. A value of 0
+ * indicates that there are 32 BD locations in the packet (the maximum).
+ * This field is valid only on the first BD of a packet.
+ */
+ #define TX_BD_SHORT_FLAGS_BD_CNT_MASK UINT32_C(0x1f00)
+ #define TX_BD_SHORT_FLAGS_BD_CNT_SFT 8
+ /*
+ * This value is a hint for the length of the entire packet. It is used
+ * by the chip to optimize internal processing. The packet will be
+ * dropped if the hint is too short. This field is valid only on the
+ * first BD of a packet.
+ */
+ #define TX_BD_SHORT_FLAGS_LHINT_MASK UINT32_C(0x6000)
+ #define TX_BD_SHORT_FLAGS_LHINT_SFT 13
+ /* indicates packet length < 512B */
+ #define TX_BD_SHORT_FLAGS_LHINT_LT512 (UINT32_C(0x0) << 13)
+ /* indicates 512 <= packet length < 1KB */
+ #define TX_BD_SHORT_FLAGS_LHINT_LT1K (UINT32_C(0x1) << 13)
+ /* indicates 1KB <= packet length < 2KB */
+ #define TX_BD_SHORT_FLAGS_LHINT_LT2K (UINT32_C(0x2) << 13)
+ /* indicates packet length >= 2KB */
+ #define TX_BD_SHORT_FLAGS_LHINT_GTE2K (UINT32_C(0x3) << 13)
+ #define TX_BD_SHORT_FLAGS_LHINT_LAST TX_BD_SHORT_FLAGS_LHINT_GTE2K
+ /*
+ * If set to 1, the device immediately updates the Send Consumer Index
+ * after the buffer associated with this descriptor has been transferred
+ * via DMA to NIC memory from host memory. An interrupt may or may not
+ * be generated according to the state of the interrupt avoidance
+ * mechanisms. If this bit is set to 0, then the Consumer Index is only
+ * updated as soon as one of the host interrupt coalescing conditions
+ * has been met. This bit must be valid on the first BD of a packet.
+ */
+ #define TX_BD_SHORT_FLAGS_COAL_NOW UINT32_C(0x8000)
+ /*
+ * All bits in this field must be valid on the first BD of a packet.
+ * Only the packet_end bit must be valid for the remaining BDs of a
+ * packet.
+ */
+ #define TX_BD_SHORT_FLAGS_MASK UINT32_C(0xffc0)
+ #define TX_BD_SHORT_FLAGS_SFT 6
+ uint16_t flags_type;
+
+ /*
+ * This is the length of the host physical buffer this BD describes in
+ * bytes. This field must be valid on all BDs of a packet.
+ */
+ uint16_t len;
+ /*
+ * The opaque data field is pass through to the completion and can be
+ * used for any data that the driver wants to associate with the
+ * transmit BD. This field must be valid on the first BD of a packet.
+ */
+ uint32_t opaque;
+
+ /*
+ * This is the host physical address for the portion of the packet
+ * described by this TX BD. This value must be valid on all BDs of a
+ * packet.
+ */
+ uint64_t addr;
+} __attribute__((packed));
+
+/* Long TX BD (32 bytes split to 2 16-byte struct) */
+struct tx_bd_long {
+ /*
+ * All bits in this field must be valid on the first BD of a packet.
+ * Only the packet_end bit must be valid for the remaining BDs of a
+ * packet.
+ */
+ /* This value identifies the type of buffer descriptor. */
+ #define TX_BD_LONG_TYPE_MASK UINT32_C(0x3f)
+ #define TX_BD_LONG_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 32B long and is used for normal L2
+ * packet transmission.
+ */
+ #define TX_BD_LONG_TYPE_TX_BD_LONG (UINT32_C(0x10) << 0)
+ /*
+ * If set to 1, the packet ends with the data in the buffer pointed to
+ * by this descriptor. This flag must be valid on every BD.
+ */
+ #define TX_BD_LONG_FLAGS_PACKET_END UINT32_C(0x40)
+ /*
+ * If set to 1, the device will not generate a completion for this
+ * transmit packet unless there is an error in it's processing. If this
+ * bit is set to 0, then the packet will be completed normally. This bit
+ * must be valid only on the first BD of a packet.
+ */
+ #define TX_BD_LONG_FLAGS_NO_CMPL UINT32_C(0x80)
+ /*
+ * This value indicates how many 16B BD locations are consumed in the
+ * ring by this packet. A value of 1 indicates that this BD is the only
+ * BD (and that the it is a short BD). A value of 3 indicates either 3
+ * short BDs or 1 long BD and one short BD in the packet. A value of 0
+ * indicates that there are 32 BD locations in the packet (the maximum).
+ * This field is valid only on the first BD of a packet.
+ */
+ #define TX_BD_LONG_FLAGS_BD_CNT_MASK UINT32_C(0x1f00)
+ #define TX_BD_LONG_FLAGS_BD_CNT_SFT 8
+ /*
+ * This value is a hint for the length of the entire packet. It is used
+ * by the chip to optimize internal processing. The packet will be
+ * dropped if the hint is too short. This field is valid only on the
+ * first BD of a packet.
+ */
+ #define TX_BD_LONG_FLAGS_LHINT_MASK UINT32_C(0x6000)
+ #define TX_BD_LONG_FLAGS_LHINT_SFT 13
+ /* indicates packet length < 512B */
+ #define TX_BD_LONG_FLAGS_LHINT_LT512 (UINT32_C(0x0) << 13)
+ /* indicates 512 <= packet length < 1KB */
+ #define TX_BD_LONG_FLAGS_LHINT_LT1K (UINT32_C(0x1) << 13)
+ /* indicates 1KB <= packet length < 2KB */
+ #define TX_BD_LONG_FLAGS_LHINT_LT2K (UINT32_C(0x2) << 13)
+ /* indicates packet length >= 2KB */
+ #define TX_BD_LONG_FLAGS_LHINT_GTE2K (UINT32_C(0x3) << 13)
+ #define TX_BD_LONG_FLAGS_LHINT_LAST TX_BD_LONG_FLAGS_LHINT_GTE2K
+ /*
+ * If set to 1, the device immediately updates the Send Consumer Index
+ * after the buffer associated with this descriptor has been transferred
+ * via DMA to NIC memory from host memory. An interrupt may or may not
+ * be generated according to the state of the interrupt avoidance
+ * mechanisms. If this bit is set to 0, then the Consumer Index is only
+ * updated as soon as one of the host interrupt coalescing conditions
+ * has been met. This bit must be valid on the first BD of a packet.
+ */
+ #define TX_BD_LONG_FLAGS_COAL_NOW UINT32_C(0x8000)
+ /*
+ * All bits in this field must be valid on the first BD of a packet.
+ * Only the packet_end bit must be valid for the remaining BDs of a
+ * packet.
+ */
+ #define TX_BD_LONG_FLAGS_MASK UINT32_C(0xffc0)
+ #define TX_BD_LONG_FLAGS_SFT 6
+ uint16_t flags_type;
+
+ /*
+ * This is the length of the host physical buffer this BD describes in
+ * bytes. This field must be valid on all BDs of a packet.
+ */
+ uint16_t len;
+
+ /*
+ * The opaque data field is pass through to the completion and can be
+ * used for any data that the driver wants to associate with the
+ * transmit BD. This field must be valid on the first BD of a packet.
+ */
+ uint32_t opaque;
+
+ /*
+ * This is the host physical address for the portion of the packet
+ * described by this TX BD. This value must be valid on all BDs of a
+ * packet.
+ */
+ uint64_t addr;
+} __attribute__((packed));
+
+/* last 16 bytes of Long TX BD */
+
+struct tx_bd_long_hi {
+ /*
+ * All bits in this field must be valid on the first BD of a packet.
+ * Their value on other BDs of the packet will be ignored.
+ */
+ /*
+ * If set to 1, the controller replaces the TCP/UPD checksum fields of
+ * normal TCP/UPD checksum, or the inner TCP/UDP checksum field of the
+ * encapsulated TCP/UDP packets with the hardware calculated TCP/UDP
+ * checksum for the packet associated with this descriptor. This bit
+ * must be valid on the first BD of a packet.
+ */
+ #define TX_BD_LONG_LFLAGS_TCP_UDP_CHKSUM UINT32_C(0x1)
+ /*
+ * If set to 1, the controller replaces the IP checksum of the normal
+ * packets, or the inner IP checksum of the encapsulated packets with
+ * the hardware calculated IP checksum for the packet associated with
+ * this descriptor. This bit must be valid on the first BD of a packet.
+ */
+ #define TX_BD_LONG_LFLAGS_IP_CHKSUM UINT32_C(0x2)
+ /*
+ * If set to 1, the controller will not append an Ethernet CRC to the
+ * end of the frame. This bit must be valid on the first BD of a packet.
+ * Packet must be 64B or longer when this flag is set. It is not useful
+ * to use this bit with any form of TX offload such as CSO or LSO. The
+ * intent is that the packet from the host already has a valid Ethernet
+ * CRC on the packet.
+ */
+ #define TX_BD_LONG_LFLAGS_NOCRC UINT32_C(0x4)
+ /*
+ * If set to 1, the device will record the time at which the packet was
+ * actually transmitted at the TX MAC. This bit must be valid on the
+ * first BD of a packet.
+ */
+ #define TX_BD_LONG_LFLAGS_STAMP UINT32_C(0x8)
+ /*
+ * If set to 1, The controller replaces the tunnel IP checksum field
+ * with hardware calculated IP checksum for the IP header of the packet
+ * associated with this descriptor. In case of VXLAN, the controller
+ * also replaces the outer header UDP checksum with hardware calculated
+ * UDP checksum for the packet associated with this descriptor.
+ */
+ #define TX_BD_LONG_LFLAGS_T_IP_CHKSUM UINT32_C(0x10)
+ /*
+ * If set to 1, the device will treat this packet with LSO(Large Send
+ * Offload) processing for both normal or encapsulated packets, which is
+ * a form of TCP segmentation. When this bit is 1, the hdr_size and mss
+ * fields must be valid. The driver doesn't need to set t_ip_chksum,
+ * ip_chksum, and tcp_udp_chksum flags since the controller will replace
+ * the appropriate checksum fields for segmented packets. When this bit
+ * is 1, the hdr_size and mss fields must be valid.
+ */
+ #define TX_BD_LONG_LFLAGS_LSO UINT32_C(0x20)
+ /*
+ * If set to zero when LSO is '1', then the IPID will be treated as a
+ * 16b number and will be wrapped if it exceeds a value of 0xffff. If
+ * set to one when LSO is '1', then the IPID will be treated as a 15b
+ * number and will be wrapped if it exceeds a value 0f 0x7fff.
+ */
+ #define TX_BD_LONG_LFLAGS_IPID_FMT UINT32_C(0x40)
+ /*
+ * If set to zero when LSO is '1', then the IPID of the tunnel IP header
+ * will not be modified during LSO operations. If set to one when LSO is
+ * '1', then the IPID of the tunnel IP header will be incremented for
+ * each subsequent segment of an LSO operation.
+ */
+ #define TX_BD_LONG_LFLAGS_T_IPID UINT32_C(0x80)
+ /*
+ * If set to '1', then the RoCE ICRC will be appended to the packet.
+ * Packet must be a valid RoCE format packet.
+ */
+ #define TX_BD_LONG_LFLAGS_ROCE_CRC UINT32_C(0x100)
+ /*
+ * If set to '1', then the FCoE CRC will be appended to the packet.
+ * Packet must be a valid FCoE format packet.
+ */
+ #define TX_BD_LONG_LFLAGS_FCOE_CRC UINT32_C(0x200)
+ uint16_t lflags;
+
+ /*
+ * When LSO is '1', this field must contain the offset of the TCP
+ * payload from the beginning of the packet in as 16b words. In case of
+ * encapsulated/tunneling packet, this field contains the offset of the
+ * inner TCP payload from beginning of the packet as 16-bit words. This
+ * value must be valid on the first BD of a packet.
+ */
+ #define TX_BD_LONG_HDR_SIZE_MASK UINT32_C(0x1ff)
+ #define TX_BD_LONG_HDR_SIZE_SFT 0
+ uint16_t hdr_size;
+
+ /*
+ * This is the MSS value that will be used to do the LSO processing. The
+ * value is the length in bytes of the TCP payload for each segment
+ * generated by the LSO operation. This value must be valid on the first
+ * BD of a packet.
+ */
+ #define TX_BD_LONG_MSS_MASK UINT32_C(0x7fff)
+ #define TX_BD_LONG_MSS_SFT 0
+ uint32_t mss;
+
+ uint16_t unused_2;
+
+ /*
+ * This value selects a CFA action to perform on the packet. Set this
+ * value to zero if no CFA action is desired. This value must be valid
+ * on the first BD of a packet.
+ */
+ uint16_t cfa_action;
+
+ /*
+ * This value is action meta-data that defines CFA edit operations that
+ * are done in addition to any action editing.
+ */
+ /* When key=1, This is the VLAN tag VID value. */
+ #define TX_BD_LONG_CFA_META_VLAN_VID_MASK UINT32_C(0xfff)
+ #define TX_BD_LONG_CFA_META_VLAN_VID_SFT 0
+ /* When key=1, This is the VLAN tag DE value. */
+ #define TX_BD_LONG_CFA_META_VLAN_DE UINT32_C(0x1000)
+ /* When key=1, This is the VLAN tag PRI value. */
+ #define TX_BD_LONG_CFA_META_VLAN_PRI_MASK UINT32_C(0xe000)
+ #define TX_BD_LONG_CFA_META_VLAN_PRI_SFT 13
+ /* When key=1, This is the VLAN tag TPID select value. */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_MASK UINT32_C(0x70000)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_SFT 16
+ /* 0x88a8 */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID88A8 (UINT32_C(0x0) << 16)
+ /* 0x8100 */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID8100 (UINT32_C(0x1) << 16)
+ /* 0x9100 */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9100 (UINT32_C(0x2) << 16)
+ /* 0x9200 */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9200 (UINT32_C(0x3) << 16)
+ /* 0x9300 */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9300 (UINT32_C(0x4) << 16)
+ /* Value programmed in CFA VLANTPID register. */
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG (UINT32_C(0x5) << 16)
+ #define TX_BD_LONG_CFA_META_VLAN_TPID_LAST \
+ TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG
+ /* When key=1, This is the VLAN tag TPID select value. */
+ #define TX_BD_LONG_CFA_META_VLAN_RESERVED_MASK UINT32_C(0xff80000)
+ #define TX_BD_LONG_CFA_META_VLAN_RESERVED_SFT 19
+ /*
+ * This field identifies the type of edit to be performed on the packet.
+ * This value must be valid on the first BD of a packet.
+ */
+ #define TX_BD_LONG_CFA_META_KEY_MASK UINT32_C(0xf0000000)
+ #define TX_BD_LONG_CFA_META_KEY_SFT 28
+ /* No editing */
+ #define TX_BD_LONG_CFA_META_KEY_NONE (UINT32_C(0x0) << 28)
+ /*
+ * - meta[17:16] - TPID select value (0 = 0x8100). - meta[15:12]
+ * - PRI/DE value. - meta[11:0] - VID value.
+ */
+ #define TX_BD_LONG_CFA_META_KEY_VLAN_TAG (UINT32_C(0x1) << 28)
+ #define TX_BD_LONG_CFA_META_KEY_LAST TX_BD_LONG_CFA_META_KEY_VLAN_TAG
+ uint32_t cfa_meta;
+} __attribute__((packed));
+
+/* RX Producer Packet BD (16 bytes) */
+struct rx_prod_pkt_bd {
+ /* This value identifies the type of buffer descriptor. */
+ #define RX_PROD_PKT_BD_TYPE_MASK UINT32_C(0x3f)
+ #define RX_PROD_PKT_BD_TYPE_SFT 0
+ /*
+ * Indicates that this BD is 16B long and is an RX Producer (ie.
+ * empty) buffer descriptor.
+ */
+ #define RX_PROD_PKT_BD_TYPE_RX_PROD_PKT (UINT32_C(0x4) << 0)
+ /*
+ * If set to 1, the packet will be placed at the address plus 2B. The 2
+ * Bytes of padding will be written as zero.
+ */
+ /*
+ * This is intended to be used when the host buffer is cache-line
+ * aligned to produce packets that are easy to parse in host memory
+ * while still allowing writes to be cache line aligned.
+ */
+ #define RX_PROD_PKT_BD_FLAGS_SOP_PAD UINT32_C(0x40)
+ /*
+ * If set to 1, the packet write will be padded out to the nearest
+ * cache-line with zero value padding.
+ */
+ /*
+ * If receive buffers start/end on cache-line boundaries, this feature
+ * will ensure that all data writes on the PCI bus start/end on cache
+ * line boundaries.
+ */
+ #define RX_PROD_PKT_BD_FLAGS_EOP_PAD UINT32_C(0x80)
+ /*
+ * This value is the number of additional buffers in the ring that
+ * describe the buffer space to be consumed for the this packet. If the
+ * value is zero, then the packet must fit within the space described by
+ * this BD. If this value is 1 or more, it indicates how many additional
+ * "buffer" BDs are in the ring immediately following this BD to be used
+ * for the same network packet. Even if the packet to be placed does not
+ * need all the additional buffers, they will be consumed anyway.
+ */
+ #define RX_PROD_PKT_BD_FLAGS_BUFFERS_MASK UINT32_C(0x300)
+ #define RX_PROD_PKT_BD_FLAGS_BUFFERS_SFT 8
+ #define RX_PROD_PKT_BD_FLAGS_MASK UINT32_C(0xffc0)
+ #define RX_PROD_PKT_BD_FLAGS_SFT 6
+ uint16_t flags_type;
+
+ /*
+ * This is the length in Bytes of the host physical buffer where data
+ * for the packet may be placed in host memory.
+ */
+ /*
+ * While this is a Byte resolution value, it is often advantageous to
+ * ensure that the buffers provided end on a host cache line.
+ */
+ uint16_t len;
+
+ /*
+ * The opaque data field is pass through to the completion and can be
+ * used for any data that the driver wants to associate with this
+ * receive buffer set.
+ */
+ uint32_t opaque;
+
+ /*
+ * This is the host physical address where data for the packet may by
+ * placed in host memory.
+ */
+ /*
+ * While this is a Byte resolution value, it is often advantageous to
+ * ensure that the buffers provide start on a host cache line.
+ */
+ uint64_t addr;
+} __attribute__((packed));
+
+/* Completion Ring Structures */
+/* Note: This structure is used by the HWRM to communicate HWRM Error. */
+/* Base Completion Record (16 bytes) */
+struct cmpl_base {
+ /* unused is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By convention,
+ * the LSB identifies the length of the record in 16B units. Even values
+ * indicate 16B records. Odd values indicate 32B records.
+ */
+ #define CMPL_BASE_TYPE_MASK UINT32_C(0x3f)
+ #define CMPL_BASE_TYPE_SFT 0
+ /* TX L2 completion: Completion of TX packet. Length = 16B */
+ #define CMPL_BASE_TYPE_TX_L2 (UINT32_C(0x0) << 0)
+ /*
+ * RX L2 completion: Completion of and L2 RX packet.
+ * Length = 32B
+ */
+ #define CMPL_BASE_TYPE_RX_L2 (UINT32_C(0x11) << 0)
+ /*
+ * RX Aggregation Buffer completion : Completion of an L2
+ * aggregation buffer in support of TPA, HDS, or Jumbo packet
+ * completion. Length = 16B
+ */
+ #define CMPL_BASE_TYPE_RX_AGG (UINT32_C(0x12) << 0)
+ /*
+ * RX L2 TPA Start Completion: Completion at the beginning of a
+ * TPA operation. Length = 32B
+ */
+ #define CMPL_BASE_TYPE_RX_TPA_START (UINT32_C(0x13) << 0)
+ /*
+ * RX L2 TPA End Completion: Completion at the end of a TPA
+ * operation. Length = 32B
+ */
+ #define CMPL_BASE_TYPE_RX_TPA_END (UINT32_C(0x15) << 0)
+ /*
+ * Statistics Ejection Completion: Completion of statistics data
+ * ejection buffer. Length = 16B
+ */
+ #define CMPL_BASE_TYPE_STAT_EJECT (UINT32_C(0x1a) << 0)
+ /* HWRM Command Completion: Completion of an HWRM command. */
+ #define CMPL_BASE_TYPE_HWRM_DONE (UINT32_C(0x20) << 0)
+ /* Forwarded HWRM Request */
+ #define CMPL_BASE_TYPE_HWRM_FWD_REQ (UINT32_C(0x22) << 0)
+ /* Forwarded HWRM Response */
+ #define CMPL_BASE_TYPE_HWRM_FWD_RESP (UINT32_C(0x24) << 0)
+ /* HWRM Asynchronous Event Information */
+ #define CMPL_BASE_TYPE_HWRM_ASYNC_EVENT (UINT32_C(0x2e) << 0)
+ /* CQ Notification */
+ #define CMPL_BASE_TYPE_CQ_NOTIFICATION (UINT32_C(0x30) << 0)
+ /* SRQ Threshold Event */
+ #define CMPL_BASE_TYPE_SRQ_EVENT (UINT32_C(0x32) << 0)
+ /* DBQ Threshold Event */
+ #define CMPL_BASE_TYPE_DBQ_EVENT (UINT32_C(0x34) << 0)
+ /* QP Async Notification */
+ #define CMPL_BASE_TYPE_QP_EVENT (UINT32_C(0x38) << 0)
+ /* Function Async Notification */
+ #define CMPL_BASE_TYPE_FUNC_EVENT (UINT32_C(0x3a) << 0)
+ uint16_t type;
+
+ uint16_t info1;
+ uint32_t info2;
+
+ /*
+ * This value is written by the NIC such that it will be different for
+ * each pass through the completion queue. The even passes will write 1.
+ * The odd passes will write 0.
+ */
+ #define CMPL_BASE_V UINT32_C(0x1)
+ /* info3 is 31 b */
+ #define CMPL_BASE_INFO3_MASK UINT32_C(0xfffffffe)
+ #define CMPL_BASE_INFO3_SFT 1
+ uint32_t info3_v;
+
+ uint32_t info4;
+} __attribute__((packed));
+
+/* TX Completion Record (16 bytes) */
+struct tx_cmpl {
+ /*
+ * This field indicates the exact type of the completion. By convention,
+ * the LSB identifies the length of the record in 16B units. Even values
+ * indicate 16B records. Odd values indicate 32B records.
+ */
+ #define TX_CMPL_TYPE_MASK UINT32_C(0x3f)
+ #define TX_CMPL_TYPE_SFT 0
+ /* TX L2 completion: Completion of TX packet. Length = 16B */
+ #define TX_CMPL_TYPE_TX_L2 (UINT32_C(0x0) << 0)
+ /*
+ * When this bit is '1', it indicates a packet that has an error of some
+ * type. Type of error is indicated in error_flags.
+ */
+ #define TX_CMPL_FLAGS_ERROR UINT32_C(0x40)
+ /*
+ * When this bit is '1', it indicates that the packet completed was
+ * transmitted using the push acceleration data provided by the driver.
+ * When this bit is '0', it indicates that the packet had not push
+ * acceleration data written or was executed as a normal packet even
+ * though push data was provided.
+ */
+ #define TX_CMPL_FLAGS_PUSH UINT32_C(0x80)
+ #define TX_CMPL_FLAGS_MASK UINT32_C(0xffc0)
+ #define TX_CMPL_FLAGS_SFT 6
+ uint16_t flags_type;
+
+ uint16_t unused_0;
+
+ /*
+ * This is a copy of the opaque field from the first TX BD of this
+ * transmitted packet.
+ */
+ uint32_t opaque;
+
+ /*
+ * This value is written by the NIC such that it will be different for
+ * each pass through the completion queue. The even passes will write 1.
+ * The odd passes will write 0.
+ */
+ #define TX_CMPL_V UINT32_C(0x1)
+ /*
+ * This error indicates that there was some sort of problem with the BDs
+ * for the packet.
+ */
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe)
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_SFT 1
+ /* No error */
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_NO_ERROR (UINT32_C(0x0) << 1)
+ /* Bad Format: BDs were not formatted correctly. */
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT (UINT32_C(0x2) << 1)
+ #define TX_CMPL_ERRORS_BUFFER_ERROR_LAST \
+ TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT
+ /*
+ * When this bit is '1', it indicates that the length of the packet was
+ * zero. No packet was transmitted.
+ */
+ #define TX_CMPL_ERRORS_ZERO_LENGTH_PKT UINT32_C(0x10)
+ /*
+ * When this bit is '1', it indicates that the packet was longer than
+ * the programmed limit in TDI. No packet was transmitted.
+ */
+ #define TX_CMPL_ERRORS_EXCESSIVE_BD_LENGTH UINT32_C(0x20)
+ /*
+ * When this bit is '1', it indicates that one or more of the BDs
+ * associated with this packet generated a PCI error. This probably
+ * means the address was not valid.
+ */
+ #define TX_CMPL_ERRORS_DMA_ERROR UINT32_C(0x40)
+ /*
+ * When this bit is '1', it indicates that the packet was longer than
+ * indicated by the hint. No packet was transmitted.
+ */
+ #define TX_CMPL_ERRORS_HINT_TOO_SHORT UINT32_C(0x80)
+ /*
+ * When this bit is '1', it indicates that the packet was dropped due to
+ * Poison TLP error on one or more of the TLPs in the PXP completion.
+ */
+ #define TX_CMPL_ERRORS_POISON_TLP_ERROR UINT32_C(0x100)
+ #define TX_CMPL_ERRORS_MASK UINT32_C(0xfffe)
+ #define TX_CMPL_ERRORS_SFT 1
+ uint16_t errors_v;
+
+ uint16_t unused_1;
+ uint32_t unused_2;
+} __attribute__((packed)) tx_cmpl_t, *ptx_cmpl_t;
+
+/* RX Packet Completion Record (32 bytes split to 2 16-byte struct) */
+struct rx_pkt_cmpl {
+ /*
+ * This field indicates the exact type of the completion. By convention,
+ * the LSB identifies the length of the record in 16B units. Even values
+ * indicate 16B records. Odd values indicate 32B records.
+ */
+ #define RX_PKT_CMPL_TYPE_MASK UINT32_C(0x3f)
+ #define RX_PKT_CMPL_TYPE_SFT 0
+ /*
+ * RX L2 completion: Completion of and L2 RX packet.
+ * Length = 32B
+ */
+ #define RX_PKT_CMPL_TYPE_RX_L2 (UINT32_C(0x11) << 0)
+ /*
+ * When this bit is '1', it indicates a packet that has an error of some
+ * type. Type of error is indicated in error_flags.
+ */
+ #define RX_PKT_CMPL_FLAGS_ERROR UINT32_C(0x40)
+ /* This field indicates how the packet was placed in the buffer. */
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_MASK UINT32_C(0x380)
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_SFT 7
+ /* Normal: Packet was placed using normal algorithm. */
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_NORMAL (UINT32_C(0x0) << 7)
+ /* Jumbo: Packet was placed using jumbo algorithm. */
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_JUMBO (UINT32_C(0x1) << 7)
+ /*
+ * Header/Data Separation: Packet was placed using Header/Data
+ * separation algorithm. The separation location is indicated by
+ * the itype field.
+ */
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_HDS (UINT32_C(0x2) << 7)
+ #define RX_PKT_CMPL_FLAGS_PLACEMENT_LAST \
+ RX_PKT_CMPL_FLAGS_PLACEMENT_HDS
+ /* This bit is '1' if the RSS field in this completion is valid. */
+ #define RX_PKT_CMPL_FLAGS_RSS_VALID UINT32_C(0x400)
+ /*
+ * This value indicates what the inner packet determined for the packet
+ * was.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_MASK UINT32_C(0xf000)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_SFT 12
+ /* Not Known: Indicates that the packet type was not known. */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_NOT_KNOWN (UINT32_C(0x0) << 12)
+ /*
+ * IP Packet: Indicates that the packet was an IP packet, but
+ * further classification was not possible.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_IP (UINT32_C(0x1) << 12)
+ /*
+ * TCP Packet: Indicates that the packet was IP and TCP. This
+ * indicates that the payload_offset field is valid.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_TCP (UINT32_C(0x2) << 12)
+ /*
+ * UDP Packet: Indicates that the packet was IP and UDP. This
+ * indicates that the payload_offset field is valid.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_UDP (UINT32_C(0x3) << 12)
+ /*
+ * FCoE Packet: Indicates that the packet was recognized as a
+ * FCoE. This also indicates that the payload_offset field is
+ * valid.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_FCOE (UINT32_C(0x4) << 12)
+ /*
+ * RoCE Packet: Indicates that the packet was recognized as a
+ * RoCE. This also indicates that the payload_offset field is
+ * valid.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_ROCE (UINT32_C(0x5) << 12)
+ /*
+ * ICMP Packet: Indicates that the packet was recognized as
+ * ICMP. This indicates that the payload_offset field is valid.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_ICMP (UINT32_C(0x7) << 12)
+ /*
+ * PtP packet wo/timestamp: Indicates that the packet was
+ * recognized as a PtP packet.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_WO_TIMESTAMP \
+ (UINT32_C(0x8) << 12)
+ /*
+ * PtP packet w/timestamp: Indicates that the packet was
+ * recognized as a PtP packet and that a timestamp was taken for
+ * the packet.
+ */
+ #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP (UINT32_C(0x9) << 12)
+ #define RX_PKT_CMPL_FLAGS_ITYPE_LAST \
+ RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP
+ #define RX_PKT_CMPL_FLAGS_MASK UINT32_C(0xffc0)
+ #define RX_PKT_CMPL_FLAGS_SFT 6
+ uint16_t flags_type;
+
+ /*
+ * This is the length of the data for the packet stored in the buffer(s)
+ * identified by the opaque value. This includes the packet BD and any
+ * associated buffer BDs. This does not include the the length of any
+ * data places in aggregation BDs.
+ */
+ uint16_t len;
+
+ /*
+ * This is a copy of the opaque field from the RX BD this completion
+ * corresponds to.
+ */
+ uint32_t opaque;
+
+ /*
+ * This value is written by the NIC such that it will be different for
+ * each pass through the completion queue. The even passes will write 1.
+ * The odd passes will write 0.
+ */
+ #define RX_PKT_CMPL_V1 UINT32_C(0x1)
+ /*
+ * This value is the number of aggregation buffers that follow this
+ * entry in the completion ring that are a part of this packet. If the
+ * value is zero, then the packet is completely contained in the buffer
+ * space provided for the packet in the RX ring.
+ */
+ #define RX_PKT_CMPL_AGG_BUFS_MASK UINT32_C(0x3e)
+ #define RX_PKT_CMPL_AGG_BUFS_SFT 1
+ uint8_t agg_bufs_v1;
+
+ /*
+ * This is the RSS hash type for the packet. The value is packed
+ * {tuple_extrac_op[1:0],rss_profile_id[4:0],tuple_extrac_op[2]}.
+ */
+ uint8_t rss_hash_type;
+
+ /*
+ * This value indicates the offset from the beginning of the packet
+ * where the inner payload starts. This value is valid for TCP, UDP,
+ * FCoE, and RoCE packets.
+ */
+ uint8_t payload_offset;
+
+ uint8_t unused_1;
+
+ /*
+ * This value is the RSS hash value calculated for the packet based on
+ * the mode bits and key value in the VNIC.
+ */
+ uint32_t rss_hash;
+} __attribute__((packed));
+
+/* last 16 bytes of RX Packet Completion Record */
+struct rx_pkt_cmpl_hi {
+ /*
+ * This indicates that the ip checksum was calculated for the inner
+ * packet and that the ip_cs_error field indicates if there was an
+ * error.
+ */
+ #define RX_PKT_CMPL_FLAGS2_IP_CS_CALC UINT32_C(0x1)
+ /*
+ * This indicates that the TCP, UDP or ICMP checksum was calculated for
+ * the inner packet and that the l4_cs_error field indicates if there
+ * was an error.
+ */
+ #define RX_PKT_CMPL_FLAGS2_L4_CS_CALC UINT32_C(0x2)
+ /*
+ * This indicates that the ip checksum was calculated for the tunnel
+ * header and that the t_ip_cs_error field indicates if there was an
+ * error.
+ */
+ #define RX_PKT_CMPL_FLAGS2_T_IP_CS_CALC UINT32_C(0x4)
+ /*
+ * This indicates that the UDP checksum was calculated for the tunnel
+ * packet and that the t_l4_cs_error field indicates if there was an
+ * error.
+ */
+ #define RX_PKT_CMPL_FLAGS2_T_L4_CS_CALC UINT32_C(0x8)
+ /* This value indicates what format the metadata field is. */
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_MASK UINT32_C(0xf0)
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_SFT 4
+ /* No metadata informtaion. Value is zero. */
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_NONE (UINT32_C(0x0) << 4)
+ /*
+ * The metadata field contains the VLAN tag and TPID value. -
+ * metadata[11:0] contains the vlan VID value. - metadata[12]
+ * contains the vlan DE value. - metadata[15:13] contains the
+ * vlan PRI value. - metadata[31:16] contains the vlan TPID
+ * value.
+ */
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN (UINT32_C(0x1) << 4)
+ #define RX_PKT_CMPL_FLAGS2_META_FORMAT_LAST \
+ RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN
+ /*
+ * This field indicates the IP type for the inner-most IP header. A
+ * value of '0' indicates IPv4. A value of '1' indicates IPv6. This
+ * value is only valid if itype indicates a packet with an IP header.
+ */
+ #define RX_PKT_CMPL_FLAGS2_IP_TYPE UINT32_C(0x100)
+ uint32_t flags2;
+
+ /*
+ * This is data from the CFA block as indicated by the meta_format
+ * field.
+ */
+ /* When meta_format=1, this value is the VLAN VID. */
+ #define RX_PKT_CMPL_METADATA_VID_MASK UINT32_C(0xfff)
+ #define RX_PKT_CMPL_METADATA_VID_SFT 0
+ /* When meta_format=1, this value is the VLAN DE. */
+ #define RX_PKT_CMPL_METADATA_DE UINT32_C(0x1000)
+ /* When meta_format=1, this value is the VLAN PRI. */
+ #define RX_PKT_CMPL_METADATA_PRI_MASK UINT32_C(0xe000)
+ #define RX_PKT_CMPL_METADATA_PRI_SFT 13
+ /* When meta_format=1, this value is the VLAN TPID. */
+ #define RX_PKT_CMPL_METADATA_TPID_MASK UINT32_C(0xffff0000)
+ #define RX_PKT_CMPL_METADATA_TPID_SFT 16
+ uint32_t metadata;
+
+ /*
+ * This value is written by the NIC such that it will be different for
+ * each pass through the completion queue. The even passes will write 1.
+ * The odd passes will write 0.
+ */
+ #define RX_PKT_CMPL_V2 UINT32_C(0x1)
+ /*
+ * This error indicates that there was some sort of problem with the BDs
+ * for the packet that was found after part of the packet was already
+ * placed. The packet should be treated as invalid.
+ */
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_MASK UINT32_C(0xe)
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_SFT 1
+ /* No buffer error */
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NO_BUFFER \
+ (UINT32_C(0x0) << 1)
+ /*
+ * Did Not Fit: Packet did not fit into packet buffer provided.
+ * For regular placement, this means the packet did not fit in
+ * the buffer provided. For HDS and jumbo placement, this means
+ * that the packet could not be placed into 7 physical buffers
+ * or less.
+ */
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_DID_NOT_FIT \
+ (UINT32_C(0x1) << 1)
+ /*
+ * Not On Chip: All BDs needed for the packet were not on-chip
+ * when the packet arrived.
+ */
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP \
+ (UINT32_C(0x2) << 1)
+ /* Bad Format: BDs were not formatted correctly. */
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT \
+ (UINT32_C(0x3) << 1)
+ #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_LAST \
+ RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT
+ /* This indicates that there was an error in the IP header checksum. */
+ #define RX_PKT_CMPL_ERRORS_IP_CS_ERROR UINT32_C(0x10)
+ /*
+ * This indicates that there was an error in the TCP, UDP or ICMP
+ * checksum.
+ */
+ #define RX_PKT_CMPL_ERRORS_L4_CS_ERROR UINT32_C(0x20)
+ /*
+ * This indicates that there was an error in the tunnel IP header
+ * checksum.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_IP_CS_ERROR UINT32_C(0x40)
+ /* This indicates that there was an error in the tunnel UDP checksum. */
+ #define RX_PKT_CMPL_ERRORS_T_L4_CS_ERROR UINT32_C(0x80)
+ /*
+ * This indicates that there was a CRC error on either an FCoE or RoCE
+ * packet. The itype indicates the packet type.
+ */
+ #define RX_PKT_CMPL_ERRORS_CRC_ERROR UINT32_C(0x100)
+ /*
+ * This indicates that there was an error in the tunnel portion of the
+ * packet when this field is non-zero.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_MASK UINT32_C(0xe00)
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_SFT 9
+ /*
+ * No additional error occurred on the tunnel portion of the
+ * packet of the packet does not have a tunnel.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_NO_ERROR (UINT32_C(0x0) << 9)
+ /*
+ * Indicates that IP header version does not match expectation
+ * from L2 Ethertype for IPv4 and IPv6 in the tunnel header.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_VERSION \
+ (UINT32_C(0x1) << 9)
+ /*
+ * Indicates that header length is out of range in the tunnel
+ * header. Valid for IPv4.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_HDR_LEN \
+ (UINT32_C(0x2) << 9)
+ /*
+ * Indicates that the physical packet is shorter than that
+ * claimed by the PPPoE header length for a tunnel PPPoE packet.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_TUNNEL_TOTAL_ERROR \
+ (UINT32_C(0x3) << 9)
+ /*
+ * Indicates that physical packet is shorter than that claimed
+ * by the tunnel l3 header length. Valid for IPv4, or IPv6
+ * tunnel packet packets.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_IP_TOTAL_ERROR \
+ (UINT32_C(0x4) << 9)
+ /*
+ * Indicates that the physical packet is shorter than that
+ * claimed by the tunnel UDP header length for a tunnel UDP
+ * packet that is not fragmented.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_UDP_TOTAL_ERROR \
+ (UINT32_C(0x5) << 9)
+ /*
+ * indicates that the IPv4 TTL or IPv6 hop limit check have
+ * failed (e.g. TTL = 0) in the tunnel header. Valid for IPv4,
+ * and IPv6.
+ */
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL \
+ (UINT32_C(0x6) << 9)
+ #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_LAST \
+ RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL
+ /*
+ * This indicates that there was an error in the inner portion of the
+ * packet when this field is non-zero.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_MASK UINT32_C(0xf000)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_SFT 12
+ /*
+ * No additional error occurred on the tunnel portion of the
+ * packet of the packet does not have a tunnel.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_NO_ERROR (UINT32_C(0x0) << 12)
+ /*
+ * Indicates that IP header version does not match expectation
+ * from L2 Ethertype for IPv4 and IPv6 or that option other than
+ * VFT was parsed on FCoE packet.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_VERSION \
+ (UINT32_C(0x1) << 12)
+ /*
+ * indicates that header length is out of range. Valid for IPv4
+ * and RoCE
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_HDR_LEN \
+ (UINT32_C(0x2) << 12)
+ /*
+ * indicates that the IPv4 TTL or IPv6 hop limit check have
+ * failed (e.g. TTL = 0). Valid for IPv4, and IPv6
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_TTL (UINT32_C(0x3) << 12)
+ /*
+ * Indicates that physical packet is shorter than that claimed
+ * by the l3 header length. Valid for IPv4, IPv6 packet or RoCE
+ * packets.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_IP_TOTAL_ERROR \
+ (UINT32_C(0x4) << 12)
+ /*
+ * Indicates that the physical packet is shorter than that
+ * claimed by the UDP header length for a UDP packet that is not
+ * fragmented.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_UDP_TOTAL_ERROR \
+ (UINT32_C(0x5) << 12)
+ /*
+ * Indicates that TCP header length > IP payload. Valid for TCP
+ * packets only.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN \
+ (UINT32_C(0x6) << 12)
+ /* Indicates that TCP header length < 5. Valid for TCP. */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN_TOO_SMALL \
+ (UINT32_C(0x7) << 12)
+ /*
+ * Indicates that TCP option headers result in a TCP header size
+ * that does not match data offset in TCP header. Valid for TCP.
+ */
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN \
+ (UINT32_C(0x8) << 12)
+ #define RX_PKT_CMPL_ERRORS_PKT_ERROR_LAST \
+ RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN
+ #define RX_PKT_CMPL_ERRORS_MASK UINT32_C(0xfffe)
+ #define RX_PKT_CMPL_ERRORS_SFT 1
+ uint16_t errors_v2;
+
+ /*
+ * This field identifies the CFA action rule that was used for this
+ * packet.
+ */
+ uint16_t cfa_code;
+
+ /*
+ * This value holds the reordering sequence number for the packet. If
+ * the reordering sequence is not valid, then this value is zero. The
+ * reordering domain for the packet is in the bottom 8 to 10b of the
+ * rss_hash value. The bottom 20b of this value contain the ordering
+ * domain value for the packet.
+ */
+ #define RX_PKT_CMPL_REORDER_MASK UINT32_C(0xffffff)
+ #define RX_PKT_CMPL_REORDER_SFT 0
+ uint32_t reorder;
+} __attribute__((packed));
+
+/* HWRM Forwarded Request (16 bytes) */
+struct hwrm_fwd_req_cmpl {
+ /* Length of forwarded request in bytes. */
+ /*
+ * This field indicates the exact type of the completion. By convention,
+ * the LSB identifies the length of the record in 16B units. Even values
+ * indicate 16B records. Odd values indicate 32B records.
+ */
+ #define HWRM_FWD_REQ_CMPL_TYPE_MASK UINT32_C(0x3f)
+ #define HWRM_FWD_REQ_CMPL_TYPE_SFT 0
+ /* Forwarded HWRM Request */
+ #define HWRM_FWD_REQ_CMPL_TYPE_HWRM_FWD_REQ (UINT32_C(0x22) << 0)
+ /* Length of forwarded request in bytes. */
+ #define HWRM_FWD_REQ_CMPL_REQ_LEN_MASK UINT32_C(0xffc0)
+ #define HWRM_FWD_REQ_CMPL_REQ_LEN_SFT 6
+ uint16_t req_len_type;
+
+ /*
+ * Source ID of this request. Typically used in forwarding requests and
+ * responses. 0x0 - 0xFFF8 - Used for function ids 0xFFF8 - 0xFFFE -
+ * Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t source_id;
+
+ uint32_t unused_0;
+
+ /* Address of forwarded request. */
+ /*
+ * This value is written by the NIC such that it will be different for
+ * each pass through the completion queue. The even passes will write 1.
+ * The odd passes will write 0.
+ */
+ #define HWRM_FWD_REQ_CMPL_V UINT32_C(0x1)
+ /* Address of forwarded request. */
+ #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_MASK UINT32_C(0xfffffffe)
+ #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_SFT 1
+ uint64_t req_buf_addr_v;
+} __attribute__((packed));
+
+/* HWRM Asynchronous Event Completion Record (16 bytes) */
+struct hwrm_async_event_cmpl {
+ /*
+ * This field indicates the exact type of the completion. By convention,
+ * the LSB identifies the length of the record in 16B units. Even values
+ * indicate 16B records. Odd values indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_MASK UINT32_C(0x3f)
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT \
+ (UINT32_C(0x2e) << 0)
+ uint16_t type;
+
+ /* Identifiers of events. */
+ /* Link status changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_STATUS_CHANGE \
+ (UINT32_C(0x0) << 0)
+ /* Link MTU changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_MTU_CHANGE \
+ (UINT32_C(0x1) << 0)
+ /* Link speed changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CHANGE \
+ (UINT32_C(0x2) << 0)
+ /* DCB Configuration changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DCB_CONFIG_CHANGE \
+ (UINT32_C(0x3) << 0)
+ /* Port connection not allowed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_CONN_NOT_ALLOWED \
+ (UINT32_C(0x4) << 0)
+ /* Link speed configuration was not allowed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \
+ (UINT32_C(0x5) << 0)
+ /* Function driver unloaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_UNLOAD \
+ (UINT32_C(0x10) << 0)
+ /* Function driver loaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_LOAD \
+ (UINT32_C(0x11) << 0)
+ /* PF driver unloaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_UNLOAD \
+ (UINT32_C(0x20) << 0)
+ /* PF driver loaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_LOAD \
+ (UINT32_C(0x21) << 0)
+ /* VF Function Level Reset (FLR) */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_FLR (UINT32_C(0x30) << 0)
+ /* VF MAC Address Change */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_MAC_ADDR_CHANGE \
+ (UINT32_C(0x31) << 0)
+ /* PF-VF communication channel status change. */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \
+ (UINT32_C(0x32) << 0)
+ /* HWRM Error */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR \
+ (UINT32_C(0xff) << 0)
+ uint16_t event_id;
+
+ /* Event specific data */
+ uint32_t event_data2;
+
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be different for
+ * each pass through the completion queue. The even passes will write 1.
+ * The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_V UINT32_C(0x1)
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_MASK UINT32_C(0xfe)
+ #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_SFT 1
+ uint8_t opaque_v;
+
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint8_t timestamp_lo;
+
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+
+ /* Event specific data */
+ uint32_t event_data1;
+} __attribute__((packed));
+
+/*
+ * Note: The Hardware Resource Manager (HWRM) manages various hardware resources
+ * inside the chip. The HWRM is implemented in firmware, and runs on embedded
+ * processors inside the chip. This firmware is vital part of the chip's
+ * hardware. The chip can not be used by driver without it.
+ */
+
+/* Input (16 bytes) */
+struct input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+} __attribute__((packed));
+
+/* Output (8 bytes) */
+struct output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_alloc */
+/*
+ * A filter is used to identify traffic that contains a matching set of
+ * parameters like unicast or broadcast MAC address or a VLAN tag amongst
+ * other things which then allows the ASIC to direct the incoming traffic
+ * to an appropriate VNIC or Rx ring.
+ */
+
+/* Input (96 bytes) */
+struct hwrm_cfa_l2_filter_alloc_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both TX and RX
+ * paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH \
+ UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX \
+ (UINT32_C(0x0) << 0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX \
+ (UINT32_C(0x1) << 0)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates the applicability to the loopback
+ * path.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP \
+ UINT32_C(0x4)
+ /*
+ * If this flag is set, all t_l2_* fields are invalid and they should
+ * not be specified. If this flag is set, then l2_* fields refer to
+ * fields of outermost L2 header.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST \
+ UINT32_C(0x8)
+ uint32_t flags;
+
+ /* This bit must be '1' for the l2_addr field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \
+ UINT32_C(0x1)
+ /* This bit must be '1' for the l2_addr_mask field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK \
+ UINT32_C(0x2)
+ /* This bit must be '1' for the l2_ovlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN \
+ UINT32_C(0x4)
+ /* This bit must be '1' for the l2_ovlan_mask field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK \
+ UINT32_C(0x8)
+ /* This bit must be '1' for the l2_ivlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the l2_ivlan_mask field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK \
+ UINT32_C(0x20)
+ /* This bit must be '1' for the t_l2_addr field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the t_l2_addr_mask field to be configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK \
+ UINT32_C(0x80)
+ /* This bit must be '1' for the t_l2_ovlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the t_l2_ovlan_mask field to be configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the t_l2_ivlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the t_l2_ivlan_mask field to be configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK \
+ UINT32_C(0x800)
+ /* This bit must be '1' for the src_type field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE \
+ UINT32_C(0x1000)
+ /* This bit must be '1' for the src_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID \
+ UINT32_C(0x2000)
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x4000)
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x10000)
+ uint32_t enables;
+
+ /*
+ * This value sets the match value for the L2 MAC address. Destination
+ * MAC address for RX path. Source MAC address for TX path.
+ */
+ uint8_t l2_addr[6];
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+
+ /*
+ * This value sets the mask value for the L2 address. A value of 0 will
+ * mask the corresponding bit from compare.
+ */
+ uint8_t l2_addr_mask[6];
+
+ /* This value sets VLAN ID value for outer VLAN. */
+ uint16_t l2_ovlan;
+
+ /*
+ * This value sets the mask value for the ovlan id. A value of 0 will
+ * mask the corresponding bit from compare.
+ */
+ uint16_t l2_ovlan_mask;
+
+ /* This value sets VLAN ID value for inner VLAN. */
+ uint16_t l2_ivlan;
+
+ /*
+ * This value sets the mask value for the ivlan id. A value of 0 will
+ * mask the corresponding bit from compare.
+ */
+ uint16_t l2_ivlan_mask;
+
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This value sets the match value for the tunnel L2 MAC address.
+ * Destination MAC address for RX path. Source MAC address for TX path.
+ */
+ uint8_t t_l2_addr[6];
+
+ uint8_t unused_4;
+ uint8_t unused_5;
+
+ /*
+ * This value sets the mask value for the tunnel L2 address. A value of
+ * 0 will mask the corresponding bit from compare.
+ */
+ uint8_t t_l2_addr_mask[6];
+
+ /* This value sets VLAN ID value for tunnel outer VLAN. */
+ uint16_t t_l2_ovlan;
+
+ /*
+ * This value sets the mask value for the tunnel ovlan id. A value of 0
+ * will mask the corresponding bit from compare.
+ */
+ uint16_t t_l2_ovlan_mask;
+
+ /* This value sets VLAN ID value for tunnel inner VLAN. */
+ uint16_t t_l2_ivlan;
+
+ /*
+ * This value sets the mask value for the tunnel ivlan id. A value of 0
+ * will mask the corresponding bit from compare.
+ */
+ uint16_t t_l2_ivlan_mask;
+
+ /* This value identifies the type of source of the packet. */
+ /* Network port */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT \
+ (UINT32_C(0x0) << 0)
+ /* Physical function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF \
+ (UINT32_C(0x1) << 0)
+ /* Virtual function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF \
+ (UINT32_C(0x2) << 0)
+ /* Virtual NIC of a function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC \
+ (UINT32_C(0x3) << 0)
+ /* Embedded processor for CFA management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG \
+ (UINT32_C(0x4) << 0)
+ /* Embedded processor for OOB management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE \
+ (UINT32_C(0x5) << 0)
+ /* Embedded processor for RoCE */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO \
+ (UINT32_C(0x6) << 0)
+ /* Embedded processor for network proxy functions */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG \
+ (UINT32_C(0x7) << 0)
+ uint8_t src_type;
+
+ uint8_t unused_6;
+ /*
+ * This value is the id of the source. For a network port, it represents
+ * port_id. For a physical function, it represents fid. For a virtual
+ * function, it represents vf_id. For a vnic, it represents vnic_id. For
+ * embedded processors, this id is not valid. Notes: 1. The function ID
+ * is implied if it src_id is not provided for a src_type that is either
+ */
+ uint32_t src_id;
+
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ (UINT32_C(0x0) << 0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Network Virtualization Generic Routing Encapsulation (NVGRE)
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ (UINT32_C(0x2) << 0)
+ /*
+ * Generic Routing Encapsulation (GRE) inside Ethernet payload
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ (UINT32_C(0x3) << 0)
+ /* IP in IP */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ (UINT32_C(0x4) << 0)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ (UINT32_C(0x5) << 0)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ (UINT32_C(0x6) << 0)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ (UINT32_C(0x7) << 0)
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP datagram
+ * payload
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ (UINT32_C(0x8) << 0)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ (UINT32_C(0xff) << 0)
+ uint8_t tunnel_type;
+
+ uint8_t unused_7;
+
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint16_t dst_id;
+
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint16_t mirror_vnic_id;
+
+ /*
+ * This hint is provided to help in placing the filter in the filter
+ * table.
+ */
+ /* No preference */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
+ (UINT32_C(0x0) << 0)
+ /* Above the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER \
+ (UINT32_C(0x1) << 0)
+ /* Below the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER \
+ (UINT32_C(0x2) << 0)
+ /* As high as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX \
+ (UINT32_C(0x3) << 0)
+ /* As low as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN \
+ (UINT32_C(0x4) << 0)
+ uint8_t pri_hint;
+
+ uint8_t unused_8;
+ uint32_t unused_9;
+
+ /*
+ * This is the ID of the filter that goes along with the pri_hint. This
+ * field is valid only for the following values. 1 - Above the given
+ * filter 2 - Below the given filter
+ */
+ uint64_t l2_filter_id_hint;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_cfa_l2_filter_alloc_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+
+ /*
+ * This is the ID of the flow associated with this filter. This value
+ * shall be used to match and associate the flow identifier returned in
+ * completion records. A value of 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint32_t flow_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_free */
+/*
+ * Description: Free a L2 filter. The HWRM shall free all associated filter
+ * resources with the L2 filter.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_cfa_l2_filter_free_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_filter_free_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_set_rx_mask */
+/* Description: This command will set rx mask of the function. */
+
+/* Input (40 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* VNIC ID */
+ uint32_t vnic_id;
+
+ /* Reserved for future use. */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_RESERVED UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is requested to accept multi-cast
+ * packets specified by the multicast addr table.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST UINT32_C(0x2)
+ /*
+ * When this bit is '1', the function is requested to accept all multi-
+ * cast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST UINT32_C(0x4)
+ /*
+ * When this bit is '1', the function is requested to accept broadcast
+ * packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST UINT32_C(0x8)
+ /*
+ * When this bit is '1', the function is requested to be put in the
+ * promiscuous mode. The HWRM should accept any function to set up
+ * promiscuous mode. The HWRM shall follow the semantics below for the
+ * promiscuous mode support. # When partitioning is not enabled on a
+ * port (i.e. single PF on the port), then the PF shall be allowed to be
+ * in the promiscuous mode. When the PF is in the promiscuous mode, then
+ * it shall receive all host bound traffic on that port. # When
+ * partitioning is enabled on a port (i.e. multiple PFs per port) and a
+ * PF on that port is in the promiscuous mode, then the PF receives all
+ * traffic within that partition as identified by a unique identifier
+ * for the PF (e.g. S-Tag). If a unique outer VLAN for the PF is
+ * specified, then the setting of promiscuous mode on that PF shall
+ * result in the PF receiving all host bound traffic with matching outer
+ * VLAN. # A VF shall can be set in the promiscuous mode. In the
+ * promiscuous mode, the VF does not receive any traffic unless a unique
+ * outer VLAN for the VF is specified. If a unique outer VLAN for the VF
+ * is specified, then the setting of promiscuous mode on that VF shall
+ * result in the VF receiving all host bound traffic with the matching
+ * outer VLAN. # The HWRM shall allow the setting of promiscuous mode on
+ * a function independently from the promiscuous mode settings on other
+ * functions.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS UINT32_C(0x10)
+ /*
+ * If this flag is set, the corresponding RX filters shall be set up to
+ * cover multicast/broadcast filters for the outermost Layer 2
+ * destination MAC address field.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST UINT32_C(0x20)
+ uint32_t mask;
+
+ /* This is the address for mcast address tbl. */
+ uint64_t mc_tbl_addr;
+
+ /*
+ * This value indicates how many entries in mc_tbl are valid. Each entry
+ * is 6 bytes.
+ */
+ uint32_t num_mc_entries;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_exec_fwd_resp */
+/*
+ * Description: This command is used to send an encapsulated request to the
+ * HWRM. This command instructs the HWRM to execute the request and forward the
+ * response of the encapsulated request to the location specified in the
+ * original request that is encapsulated. The target id of this command shall be
+ * set to 0xFFFF (HWRM). The response location in this command shall be used to
+ * acknowledge the receipt of the encapsulated request and forwarding of the
+ * response.
+ */
+
+/* Input (128 bytes) */
+struct hwrm_exec_fwd_resp_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * This is an encapsulated request. This request should be executed by
+ * the HWRM and the response should be provided in the response buffer
+ * inside the encapsulated request.
+ */
+ uint32_t encap_request[26];
+
+ /*
+ * This value indicates the target id of the response to the
+ * encapsulated request. 0x0 - 0xFFF8 - Used for function ids 0xFFF8 -
+ * 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t encap_resp_target_id;
+
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_exec_fwd_resp_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_func_qcaps */
+/*
+ * Description: This command returns capabilities of a function. The input FID
+ * value is used to indicate what function is being queried. This allows a
+ * physical function driver to query virtual functions that are children of the
+ * physical function. The output FID value is needed to configure Rings and
+ * MSI-X vectors so their DMA operations appear correctly on the PCI bus.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_func_qcaps_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * Function ID of the function that is being queried. 0xFF... (All Fs)
+ * if the query is for the requesting function.
+ */
+ uint16_t fid;
+
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (80 bytes) */
+struct hwrm_func_qcaps_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /*
+ * FID value. This value is used to identify operations on the PCI bus
+ * as belonging to a particular PCI function.
+ */
+ uint16_t fid;
+
+ /*
+ * Port ID of port that this function is associated with. Valid only for
+ * the PF. 0xFF... (All Fs) if this function is not associated with any
+ * port. 0xFF... (All Fs) if this function is called from a VF.
+ */
+ uint16_t port_id;
+
+ /* If 1, then Push mode is supported on this function. */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED UINT32_C(0x1)
+ /*
+ * If 1, then the global MSI-X auto-masking is enabled for the device.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING \
+ UINT32_C(0x2)
+ /*
+ * If 1, then the Precision Time Protocol (PTP) processing is supported
+ * on this function. The HWRM should enable PTP on only a single
+ * Physical Function (PF) per port.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED UINT32_C(0x4)
+ uint32_t flags;
+
+ /*
+ * This value is current MAC address configured for this function. A
+ * value of 00-00-00-00-00-00 indicates no MAC address is currently
+ * configured.
+ */
+ uint8_t perm_mac_address[6];
+
+ /*
+ * The maximum number of RSS/COS contexts that can be allocated to the
+ * function.
+ */
+ uint16_t max_rsscos_ctx;
+
+ /*
+ * The maximum number of completion rings that can be allocated to the
+ * function.
+ */
+ uint16_t max_cmpl_rings;
+
+ /*
+ * The maximum number of transmit rings that can be allocated to the
+ * function.
+ */
+ uint16_t max_tx_rings;
+
+ /*
+ * The maximum number of receive rings that can be allocated to the
+ * function.
+ */
+ uint16_t max_rx_rings;
+
+ /*
+ * The maximum number of L2 contexts that can be allocated to the
+ * function.
+ */
+ uint16_t max_l2_ctxs;
+
+ /* The maximum number of VNICs that can be allocated to the function. */
+ uint16_t max_vnics;
+
+ /*
+ * The identifier for the first VF enabled on a PF. This is valid only
+ * on the PF with SR-IOV enabled. 0xFF... (All Fs) if this command is
+ * called on a PF with SR-IOV disabled or on a VF.
+ */
+ uint16_t first_vf_id;
+
+ /*
+ * The maximum number of VFs that can be allocated to the function. This
+ * is valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if this
+ * command is called on a PF with SR-IOV disabled or on a VF.
+ */
+ uint16_t max_vfs;
+
+ /*
+ * The maximum number of statistic contexts that can be allocated to the
+ * function.
+ */
+ uint16_t max_stat_ctx;
+
+ /*
+ * The maximum number of Encapsulation records that can be offloaded by
+ * this function.
+ */
+ uint32_t max_encap_records;
+
+ /*
+ * The maximum number of decapsulation records that can be offloaded by
+ * this function.
+ */
+ uint32_t max_decap_records;
+
+ /*
+ * The maximum number of Exact Match (EM) flows that can be offloaded by
+ * this function on the TX side.
+ */
+ uint32_t max_tx_em_flows;
+
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be offloaded
+ * by this function on the TX side.
+ */
+ uint32_t max_tx_wm_flows;
+
+ /*
+ * The maximum number of Exact Match (EM) flows that can be offloaded by
+ * this function on the RX side.
+ */
+ uint32_t max_rx_em_flows;
+
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be offloaded
+ * by this function on the RX side.
+ */
+ uint32_t max_rx_wm_flows;
+
+ /*
+ * The maximum number of multicast filters that can be supported by this
+ * function on the RX side.
+ */
+ uint32_t max_mcast_filters;
+
+ /*
+ * The maximum value of flow_id that can be supported in completion
+ * records.
+ */
+ uint32_t max_flow_id;
+
+ /*
+ * The maximum number of HW ring groups that can be supported on this
+ * function.
+ */
+ uint32_t max_hw_ring_grps;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_func_reset */
+/*
+ * Description: This command resets a hardware function (PCIe function) and
+ * frees any resources used by the function. This command shall be initiated by
+ * the driver after an FLR has occurred to prepare the function for re-use. This
+ * command may also be initiated by a driver prior to doing it's own
+ * configuration. This command puts the function into the reset state. In the
+ * reset state, global and port related features of the chip are not available.
+ */
+/*
+ * Note: This command will reset a function that has already been disabled or
+ * idled. The command returns all the resources owned by the function so a new
+ * driver may allocate and configure resources normally.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_func_reset_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* This bit must be '1' for the vf_id_valid field to be configured. */
+ #define HWRM_FUNC_RESET_INPUT_ENABLES_VF_ID_VALID \
+ UINT32_C(0x1)
+ uint32_t enables;
+
+ /*
+ * The ID of the VF that this PF is trying to reset. Only the parent PF
+ * shall be allowed to reset a child VF. A parent PF driver shall use
+ * this field only when a specific child VF is requested to be reset.
+ */
+ uint16_t vf_id;
+
+ /* This value indicates the level of a function reset. */
+ /*
+ * Reset the caller function and its children VFs (if any). If
+ * no children functions exist, then reset the caller function
+ * only.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETALL \
+ (UINT32_C(0x0) << 0)
+ /* Reset the caller function only */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETME \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Reset all children VFs of the caller function driver if the
+ * caller is a PF driver. It is an error to specify this level
+ * by a VF driver. It is an error to specify this level by a PF
+ * driver with no children VFs.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETCHILDREN \
+ (UINT32_C(0x2) << 0)
+ /*
+ * Reset a specific VF of the caller function driver if the
+ * caller is the parent PF driver. It is an error to specify
+ * this level by a VF driver. It is an error to specify this
+ * level by a PF driver that is not the parent of the VF that is
+ * being requested to reset.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF \
+ (UINT32_C(0x3) << 0)
+ uint8_t func_reset_level;
+
+ uint8_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_reset_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_port_phy_cfg */
+/*
+ * Description: This command configures the PHY device for the port. It allows
+ * setting of the most generic settings for the PHY. The HWRM shall complete
+ * this command as soon as PHY settings are configured. They may not be applied
+ * when the command response is provided. A VF driver shall not be allowed to
+ * configure PHY using this command. In a network partition mode, a PF driver
+ * shall not be allowed to configure PHY using this command.
+ */
+
+/* Input (56 bytes) */
+struct hwrm_port_phy_cfg_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is set to '1', the PHY for the port shall be reset. #
+ * If this bit is set to 1, then the HWRM shall reset the PHY after
+ * applying PHY configuration changes specified in this command. # In
+ * order to guarantee that PHY configuration changes specified in this
+ * command take effect, the HWRM client should set this flag to 1. # If
+ * this bit is not set to 1, then the HWRM may reset the PHY depending
+ * on the current PHY configuration and settings specified in this
+ * command.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', the link shall be forced to be taken
+ * down. # When this bit is set to '1", all other command input settings
+ * related to the link speed shall be ignored. Once the link state is
+ * forced down, it can be explicitly cleared from that state by setting
+ * this flag to '0'. # If this flag is set to '0', then the link shall
+ * be cleared from forced down state if the link is in forced down
+ * state. There may be conditions (e.g. out-of-band or sideband
+ * configuration changes for the link) outside the scope of the HWRM
+ * implementation that may clear forced down link state.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DOWN UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', the link shall be forced to the
+ * force_link_speed value. When this bit is set to '1', the HWRM client
+ * should not enable any of the auto negotiation related fields
+ * represented by auto_XXX fields in this command. When this bit is set
+ * to '1' and the HWRM client has enabled a auto_XXX field in this
+ * command, then the HWRM shall ignore the enabled auto_XXX field. When
+ * this bit is set to zero, the link shall be allowed to autoneg.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', the auto-negotiation process shall be
+ * restarted on the link.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE) is
+ * requested to be enabled on this link. If EEE is not supported on this
+ * port, then this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE) is
+ * requested to be disabled on this link. If EEE is not supported on
+ * this port, then this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE UINT32_C(0x20)
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link, then TX
+ * LPI is requested to be enabled on the link. If EEE is not supported
+ * on this port, then this flag shall be ignored by the HWRM. If EEE is
+ * disabled on this port, then this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI UINT32_C(0x40)
+ uint32_t flags;
+
+ /* This bit must be '1' for the auto_mode field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE UINT32_C(0x1)
+ /* This bit must be '1' for the auto_duplex field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX UINT32_C(0x2)
+ /* This bit must be '1' for the auto_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the auto_link_speed field to be configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the auto_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the wirespeed field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIRESPEED UINT32_C(0x20)
+ /* This bit must be '1' for the lpbk field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK UINT32_C(0x40)
+ /* This bit must be '1' for the preemphasis field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS UINT32_C(0x80)
+ /* This bit must be '1' for the force_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the eee_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the tx_lpi_timer field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER UINT32_C(0x400)
+ uint32_t enables;
+
+ /* Port ID of port that is to be configured. */
+ uint16_t port_id;
+
+ /*
+ * This is the speed that will be used if the force bit is '1'. If
+ * unsupported speed is selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t force_link_speed;
+
+ /*
+ * This value is used to identify what autoneg mode is used when the
+ * link speed is not being forced.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No speeds are selected.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE (UINT32_C(0x0) << 0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Select only the auto_link_speed speed for autoneg mode. This
+ * mode has been DEPRECATED. An HWRM client should not use this
+ * mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED \
+ (UINT32_C(0x2) << 0)
+ /*
+ * Select the auto_link_speed or any speed below that speed for
+ * autoneg. This mode has been DEPRECATED. An HWRM client should
+ * not use this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW \
+ (UINT32_C(0x3) << 0)
+ /*
+ * Select the speeds based on the corresponding link speed mask
+ * value that is provided.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK \
+ (UINT32_C(0x4) << 0)
+ uint8_t auto_mode;
+
+ /*
+ * This is the duplex setting that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below".
+ */
+ /* Half Duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF \
+ (UINT32_C(0x0) << 0)
+ /* Full duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL \
+ (UINT32_C(0x1) << 0)
+ /* Both Half and Full dupex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH \
+ (UINT32_C(0x2) << 0)
+ uint8_t auto_duplex;
+
+ /*
+ * This value is used to configure the pause that will be used for
+ * autonegotiation. Add text on the usage of auto_pause and force_pause.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When the
+ * auto_mode is not set to none and this flag is set to 1, then the
+ * auto_pause bits on this port are being advertised and autoneg pause
+ * results are being interpreted. # When the auto_mode is not set to
+ * none and this flag is set to 0, the pause is forced as indicated in
+ * force_pause, and also advertised as auto_pause bits, but the autoneg
+ * results are not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is set to
+ * 1, auto_pause bits should be ignored and should be set to 0.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
+ uint8_t auto_pause;
+
+ uint8_t unused_0;
+
+ /*
+ * This is the speed that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below". If an unsupported speed is selected,
+ * an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t auto_link_speed;
+
+ /*
+ * This is a mask of link speeds that will be used if autoneg_mode is
+ * "mask". If unsupported speed is enabled an error will be generated.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint16_t auto_link_speed_mask;
+
+ /* This value controls the wirespeed feature. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_OFF (UINT32_C(0x0) << 0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_ON (UINT32_C(0x1) << 0)
+ uint8_t wirespeed;
+
+ /* This value controls the loopback setting for the PHY. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE (UINT32_C(0x0) << 0)
+ /*
+ * The HW will be configured with local loopback such that host
+ * data is sent back to the host without modification.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL (UINT32_C(0x1) << 0)
+ /*
+ * The HW will be configured with remote loopback such that port
+ * logic will send packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE (UINT32_C(0x2) << 0)
+ uint8_t lpbk;
+
+ /*
+ * This value is used to configure the pause that will be used for force
+ * mode.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX UINT32_C(0x2)
+ uint8_t force_pause;
+
+ uint8_t unused_1;
+
+ /*
+ * This value controls the pre-emphasis to be used for the link. Driver
+ * should not set this value (use enable.preemphasis = 0) unless driver
+ * is sure of setting. Normally HWRM FW will determine proper pre-
+ * emphasis.
+ */
+ uint32_t preemphasis;
+
+ /*
+ * Setting for link speed mask that is used to advertise speeds during
+ * autonegotiation when EEE is enabled. This field is valid only when
+ * EEE is enabled. The speeds specified in this field shall be a subset
+ * of speeds specified in auto_link_speed_mask. If EEE is enabled,then
+ * at least one speed shall be provided in this mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t eee_link_speed_mask;
+
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * Reuested setting of TX LPI timer in microseconds. This field is valid
+ * only when EEE is enabled and TX LPI is enabled.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK \
+ UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
+ uint32_t tx_lpi_timer;
+
+ uint32_t unused_4;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_phy_cfg_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_port_phy_qcfg */
+/* Description: This command queries the PHY configuration for the port. */
+/* Input (24 bytes) */
+
+struct hwrm_port_phy_qcfg_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* Port ID of port that is to be queried. */
+ uint16_t port_id;
+
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (96 bytes) */
+struct hwrm_port_phy_qcfg_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* This value indicates the current link status. */
+ /* There is no link or cable detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK (UINT32_C(0x0) << 0)
+ /* There is no link, but a cable has been detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL (UINT32_C(0x1) << 0)
+ /* There is a link. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK (UINT32_C(0x2) << 0)
+ uint8_t link;
+
+ uint8_t unused_0;
+
+ /* This value indicates the current link speed of the connection. */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t link_speed;
+
+ /* This value is indicates the duplex of the current connection. */
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_HALF (UINT32_C(0x0) << 0)
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_FULL (UINT32_C(0x1) << 0)
+ uint8_t duplex;
+
+ /*
+ * This value is used to indicate the current pause configuration. When
+ * autoneg is enabled, this value represents the autoneg results of
+ * pause configuration.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX UINT32_C(0x2)
+ uint8_t pause;
+
+ /*
+ * The supported speeds for the port. This is a bit mask. For each speed
+ * that is supported, the corrresponding bit will be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB \
+ UINT32_C(0x2000)
+ uint16_t support_speeds;
+
+ /*
+ * Current setting of forced link speed. When the link speed is not
+ * being forced, this value shall be set to 0.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t force_link_speed;
+
+ /* Current setting of auto negotiation mode. */
+ /*
+ * Disable autoneg or autoneg disabled. No speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE \
+ (UINT32_C(0x0) << 0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Select only the auto_link_speed speed for autoneg mode. This
+ * mode has been DEPRECATED. An HWRM client should not use this
+ * mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED \
+ (UINT32_C(0x2) << 0)
+ /*
+ * Select the auto_link_speed or any speed below that speed for
+ * autoneg. This mode has been DEPRECATED. An HWRM client should
+ * not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW \
+ (UINT32_C(0x3) << 0)
+ /*
+ * Select the speeds based on the corresponding link speed mask
+ * value that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK \
+ (UINT32_C(0x4) << 0)
+ uint8_t auto_mode;
+
+ /*
+ * Current setting of pause autonegotiation. Move autoneg_pause flag
+ * here.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When the
+ * auto_mode is not set to none and this flag is set to 1, then the
+ * auto_pause bits on this port are being advertised and autoneg pause
+ * results are being interpreted. # When the auto_mode is not set to
+ * none and this flag is set to 0, the pause is forced as indicated in
+ * force_pause, and also advertised as auto_pause bits, but the autoneg
+ * results are not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is set to
+ * 1, auto_pause bits should be ignored and should be set to 0.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE \
+ UINT32_C(0x4)
+ uint8_t auto_pause;
+
+ /*
+ * Current setting for auto_link_speed. This field is only valid when
+ * auto_mode is set to "one_speed" or "one_or_below".
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB \
+ (UINT32_C(0x1) << 0)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB \
+ (UINT32_C(0xa) << 0)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB \
+ (UINT32_C(0x14) << 0)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB \
+ (UINT32_C(0x19) << 0)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB \
+ (UINT32_C(0x64) << 0)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB \
+ (UINT32_C(0xc8) << 0)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB \
+ (UINT32_C(0xfa) << 0)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB \
+ (UINT32_C(0x190) << 0)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB \
+ (UINT32_C(0x1f4) << 0)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB \
+ (UINT32_C(0x3e8) << 0)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB \
+ (UINT32_C(0xffff) << 0)
+ uint16_t auto_link_speed;
+
+ /*
+ * Current setting for auto_link_speed_mask that is used to advertise
+ * speeds during autonegotiation. This field is only valid when
+ * auto_mode is set to "mask". The speeds specified in this field shall
+ * be a subset of supported speeds on this port.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint16_t auto_link_speed_mask;
+
+ /* Current setting for wirespeed. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_OFF (UINT32_C(0x0) << 0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_ON (UINT32_C(0x1) << 0)
+ uint8_t wirespeed;
+
+ /* Current setting for loopback. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE (UINT32_C(0x0) << 0)
+ /*
+ * The HW will be configured with local loopback such that host
+ * data is sent back to the host without modification.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL (UINT32_C(0x1) << 0)
+ /*
+ * The HW will be configured with remote loopback such that port
+ * logic will send packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE (UINT32_C(0x2) << 0)
+ uint8_t lpbk;
+
+ /*
+ * Current setting of forced pause. When the pause configuration is not
+ * being forced, then this value shall be set to 0.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX \
+ UINT32_C(0x2)
+ uint8_t force_pause;
+
+ /*
+ * This value indicates the current status of the optics module on this
+ * port.
+ */
+ /* Module is inserted and accepted */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE \
+ (UINT32_C(0x0) << 0)
+ /* Module is rejected and transmit side Laser is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX \
+ (UINT32_C(0x1) << 0)
+ /* Module mismatch warning. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG \
+ (UINT32_C(0x2) << 0)
+ /* Module is rejected and powered down. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN \
+ (UINT32_C(0x3) << 0)
+ /* Module is not inserted. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED \
+ (UINT32_C(0x4) << 0)
+ /* Module status is not applicable. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE \
+ (UINT32_C(0xff) << 0)
+ uint8_t module_status;
+
+ /* Current setting for preemphasis. */
+ uint32_t preemphasis;
+
+ /* This field represents the major version of the PHY. */
+ uint8_t phy_maj;
+
+ /* This field represents the minor version of the PHY. */
+ uint8_t phy_min;
+
+ /* This field represents the build version of the PHY. */
+ uint8_t phy_bld;
+
+ /* This value represents a PHY type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 0)
+ /* BASE-CR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR \
+ (UINT32_C(0x1) << 0)
+ /* BASE-KR4 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 \
+ (UINT32_C(0x2) << 0)
+ /* BASE-LR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR \
+ (UINT32_C(0x3) << 0)
+ /* BASE-SR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR \
+ (UINT32_C(0x4) << 0)
+ /* BASE-KR2 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 \
+ (UINT32_C(0x5) << 0)
+ /* BASE-KX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX \
+ (UINT32_C(0x6) << 0)
+ /* BASE-KR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR \
+ (UINT32_C(0x7) << 0)
+ /* BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET \
+ (UINT32_C(0x8) << 0)
+ /* EEE capable BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE \
+ (UINT32_C(0x9) << 0)
+ /* SGMII connected external PHY */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY \
+ (UINT32_C(0xa) << 0)
+ uint8_t phy_type;
+
+ /* This value represents a media type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 0)
+ /* Twisted Pair */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP (UINT32_C(0x1) << 0)
+ /* Direct Attached Copper */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC \
+ (UINT32_C(0x2) << 0)
+ /* Fiber */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE \
+ (UINT32_C(0x3) << 0)
+ uint8_t media_type;
+
+ /* This value represents a transceiver type. */
+ /* PHY and MAC are in the same package */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL \
+ (UINT32_C(0x1) << 0)
+ /* PHY and MAC are in different packages */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL \
+ (UINT32_C(0x2) << 0)
+ uint8_t xcvr_pkg_type;
+
+ /*
+ * This field represents flags related to EEE configuration. These EEE
+ * configuration flags are valid only when the auto_mode is not set to
+ * none (in other words autonegotiation is enabled).
+ */
+ /* This field represents PHY address. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK UINT32_C(0x1f)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT 0
+ /*
+ * When set to 1, Energy Efficient Ethernet (EEE) mode is enabled.
+ * Speeds for autoneg with EEE mode enabled are based on
+ * eee_link_speed_mask.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED \
+ UINT32_C(0x20)
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this flag
+ * shall be ignored. # If eee_enabled is set to 1 and this flag is set
+ * to 1, then Energy Efficient Ethernet (EEE) mode is enabled and in
+ * use. # If eee_enabled is set to 1 and this flag is set to 0, then
+ * Energy Efficient Ethernet (EEE) mode is enabled but is currently not
+ * in use.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE \
+ UINT32_C(0x40)
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this flag
+ * shall be ignored. # If eee_enabled is set to 1 and this flag is set
+ * to 1, then Energy Efficient Ethernet (EEE) mode is enabled and TX LPI
+ * is enabled. # If eee_enabled is set to 1 and this flag is set to 0,
+ * then Energy Efficient Ethernet (EEE) mode is enabled but TX LPI is
+ * disabled.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI \
+ UINT32_C(0x80)
+ /*
+ * This field represents flags related to EEE configuration. These EEE
+ * configuration flags are valid only when the auto_mode is not set to
+ * none (in other words autonegotiation is enabled).
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK \
+ UINT32_C(0xe0)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT 5
+ uint8_t eee_config_phy_addr;
+
+ /* Reserved field, set to 0 */
+ /*
+ * When set to 1, the parallel detection is used to determine the speed
+ * of the link partner. Parallel detection is used when a
+ * autonegotiation capable device is connected to a link parter that is
+ * not capable of autonegotiation.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT \
+ UINT32_C(0x1)
+ /* Reserved field, set to 0 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK UINT32_C(0xfe)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1
+ uint8_t parallel_detect;
+
+ /*
+ * The advertised speeds for the port by the link partner. Each
+ * advertised speed will be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \
+ UINT32_C(0x2000)
+ uint16_t link_partner_adv_speeds;
+
+ /*
+ * The advertised autoneg for the port by the link partner. This field
+ * is deprecated and should be set to 0.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \
+ (UINT32_C(0x0) << 0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS\
+ (UINT32_C(0x1) << 0)
+ /*
+ * Select only the auto_link_speed speed for autoneg mode. This
+ * mode has been DEPRECATED. An HWRM client should not use this
+ * mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
+ (UINT32_C(0x2) << 0)
+ /*
+ * Select the auto_link_speed or any speed below that speed for
+ * autoneg. This mode has been DEPRECATED. An HWRM client should
+ * not use this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
+ (UINT32_C(0x3) << 0)
+ /*
+ * Select the speeds based on the corresponding link speed mask
+ * value that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK\
+ (UINT32_C(0x4) << 0)
+ uint8_t link_partner_adv_auto_mode;
+
+ /* The advertised pause settings on the port by the link partner. */
+ /*
+ * When this bit is '1', Generation of tx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is supported.
+ * Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
+ UINT32_C(0x2)
+ uint8_t link_partner_adv_pause;
+
+ /*
+ * Current setting for link speed mask that is used to advertise speeds
+ * during autonegotiation when EEE is enabled. This field is valid only
+ * when eee_enabled flags is set to 1. The speeds specified in this
+ * field shall be a subset of speeds specified in auto_link_speed_mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t adv_eee_link_speed_mask;
+
+ /*
+ * Current setting for link speed mask that is advertised by the link
+ * partner when EEE is enabled. This field is valid only when
+ * eee_enabled flags is set to 1.
+ */
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t link_partner_adv_eee_link_speed_mask;
+
+ /* This value represents transceiver identifier type. */
+ /*
+ * Current setting of TX LPI timer in microseconds. This field is valid
+ * only when_eee_enabled flag is set to 1 and tx_lpi_enabled is set to
+ * 1.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK \
+ UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
+ /* This value represents transceiver identifier type. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT \
+ 24
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 24)
+ /* SFP/SFP+/SFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
+ (UINT32_C(0x3) << 24)
+ /* QSFP */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
+ (UINT32_C(0xc) << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
+ (UINT32_C(0xd) << 24)
+ /* QSFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
+ (UINT32_C(0x11) << 24)
+ uint32_t xcvr_identifier_type_tx_lpi_timer;
+
+ uint32_t unused_1;
+
+ /*
+ * Up to 16 bytes of null padded ASCII string representing PHY vendor.
+ * If the string is set to null, then the vendor name is not available.
+ */
+ char phy_vendor_name[16];
+
+ /*
+ * Up to 16 bytes of null padded ASCII string that identifies vendor
+ * specific part number of the PHY. If the string is set to null, then
+ * the vendor specific part number is not available.
+ */
+ char phy_vendor_partnumber[16];
+
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_ver_get */
+/*
+ * Description: This function is called by a driver to determine the HWRM
+ * interface version supported by the HWRM firmware, the version of HWRM
+ * firmware implementation, the name of HWRM firmware, the versions of other
+ * embedded firmwares, and the names of other embedded firmwares, etc. Any
+ * interface or firmware version with major = 0, minor = 0, and update = 0 shall
+ * be considered an invalid version.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_ver_get_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * This field represents the major version of HWRM interface
+ * specification supported by the driver HWRM implementation. The
+ * interface major version is intended to change only when non backward
+ * compatible changes are made to the HWRM interface specification.
+ */
+ uint8_t hwrm_intf_maj;
+
+ /*
+ * This field represents the minor version of HWRM interface
+ * specification supported by the driver HWRM implementation. A change
+ * in interface minor version is used to reflect significant backward
+ * compatible modification to HWRM interface specification. This can be
+ * due to addition or removal of functionality. HWRM interface
+ * specifications with the same major version but different minor
+ * versions are compatible.
+ */
+ uint8_t hwrm_intf_min;
+
+ /*
+ * This field represents the update version of HWRM interface
+ * specification supported by the driver HWRM implementation. The
+ * interface update version is used to reflect minor changes or bug
+ * fixes to a released HWRM interface specification.
+ */
+ uint8_t hwrm_intf_upd;
+
+ uint8_t unused_0[5];
+} __attribute__((packed));
+
+/* Output (128 bytes) */
+struct hwrm_ver_get_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /*
+ * This field represents the major version of HWRM interface
+ * specification supported by the HWRM implementation. The interface
+ * major version is intended to change only when non backward compatible
+ * changes are made to the HWRM interface specification. A HWRM
+ * implementation that is compliant with this specification shall
+ * provide value of 1 in this field.
+ */
+ uint8_t hwrm_intf_maj;
+
+ /*
+ * This field represents the minor version of HWRM interface
+ * specification supported by the HWRM implementation. A change in
+ * interface minor version is used to reflect significant backward
+ * compatible modification to HWRM interface specification. This can be
+ * due to addition or removal of functionality. HWRM interface
+ * specifications with the same major version but different minor
+ * versions are compatible. A HWRM implementation that is compliant with
+ * this specification shall provide value of 0 in this field.
+ */
+ uint8_t hwrm_intf_min;
+
+ /*
+ * This field represents the update version of HWRM interface
+ * specification supported by the HWRM implementation. The interface
+ * update version is used to reflect minor changes or bug fixes to a
+ * released HWRM interface specification. A HWRM implementation that is
+ * compliant with this specification shall provide value of 1 in this
+ * field.
+ */
+ uint8_t hwrm_intf_upd;
+
+ uint8_t hwrm_intf_rsvd;
+
+ /*
+ * This field represents the major version of HWRM firmware. A change in
+ * firmware major version represents a major firmware release.
+ */
+ uint8_t hwrm_fw_maj;
+
+ /*
+ * This field represents the minor version of HWRM firmware. A change in
+ * firmware minor version represents significant firmware functionality
+ * changes.
+ */
+ uint8_t hwrm_fw_min;
+
+ /*
+ * This field represents the build version of HWRM firmware. A change in
+ * firmware build version represents bug fixes to a released firmware.
+ */
+ uint8_t hwrm_fw_bld;
+
+ /*
+ * This field is a reserved field. This field can be used to represent
+ * firmware branches or customer specific releases tied to a specific
+ * (major,minor,update) version of the HWRM firmware.
+ */
+ uint8_t hwrm_fw_rsvd;
+
+ /*
+ * This field represents the major version of mgmt firmware. A change in
+ * major version represents a major release.
+ */
+ uint8_t mgmt_fw_maj;
+
+ /*
+ * This field represents the minor version of mgmt firmware. A change in
+ * minor version represents significant functionality changes.
+ */
+ uint8_t mgmt_fw_min;
+
+ /*
+ * This field represents the build version of mgmt firmware. A change in
+ * update version represents bug fixes.
+ */
+ uint8_t mgmt_fw_bld;
+
+ /*
+ * This field is a reserved field. This field can be used to represent
+ * firmware branches or customer specific releases tied to a specific
+ * (major,minor,update) version
+ */
+ uint8_t mgmt_fw_rsvd;
+
+ /*
+ * This field represents the major version of network control firmware.
+ * A change in major version represents a major release.
+ */
+ uint8_t netctrl_fw_maj;
+
+ /*
+ * This field represents the minor version of network control firmware.
+ * A change in minor version represents significant functionality
+ * changes.
+ */
+ uint8_t netctrl_fw_min;
+
+ /*
+ * This field represents the build version of network control firmware.
+ * A change in update version represents bug fixes.
+ */
+ uint8_t netctrl_fw_bld;
+
+ /*
+ * This field is a reserved field. This field can be used to represent
+ * firmware branches or customer specific releases tied to a specific
+ * (major,minor,update) version
+ */
+ uint8_t netctrl_fw_rsvd;
+
+ /*
+ * This field is reserved for future use. The responder should set it to
+ * 0. The requester should ignore this field.
+ */
+ uint32_t reserved1;
+
+ /*
+ * This field represents the major version of RoCE firmware. A change in
+ * major version represents a major release.
+ */
+ uint8_t roce_fw_maj;
+
+ /*
+ * This field represents the minor version of RoCE firmware. A change in
+ * minor version represents significant functionality changes.
+ */
+ uint8_t roce_fw_min;
+
+ /*
+ * This field represents the build version of RoCE firmware. A change in
+ * update version represents bug fixes.
+ */
+ uint8_t roce_fw_bld;
+
+ /*
+ * This field is a reserved field. This field can be used to represent
+ * firmware branches or customer specific releases tied to a specific
+ * (major,minor,update) version
+ */
+ uint8_t roce_fw_rsvd;
+
+ /*
+ * This field represents the name of HWRM FW (ASCII chars without NULL
+ * at the end).
+ */
+ char hwrm_fw_name[16];
+
+ /*
+ * This field represents the name of mgmt FW (ASCII chars without NULL
+ * at the end).
+ */
+ char mgmt_fw_name[16];
+
+ /*
+ * This field represents the name of network control firmware (ASCII
+ * chars without NULL at the end).
+ */
+ char netctrl_fw_name[16];
+
+ /*
+ * This field is reserved for future use. The responder should set it to
+ * 0. The requester should ignore this field.
+ */
+ uint32_t reserved2[4];
+
+ /*
+ * This field represents the name of RoCE FW (ASCII chars without NULL
+ * at the end).
+ */
+ char roce_fw_name[16];
+
+ /* This field returns the chip number. */
+ uint16_t chip_num;
+
+ /* This field returns the revision of chip. */
+ uint8_t chip_rev;
+
+ /* This field returns the chip metal number. */
+ uint8_t chip_metal;
+
+ /* This field returns the bond id of the chip. */
+ uint8_t chip_bond_id;
+
+ /*
+ * This value indicates the type of platform used for chip
+ * implementation.
+ */
+ /* ASIC */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_ASIC \
+ (UINT32_C(0x0) << 0)
+ /* FPGA platform of the chip. */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_FPGA \
+ (UINT32_C(0x1) << 0)
+ /* Palladium platform of the chip. */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM \
+ (UINT32_C(0x2) << 0)
+ uint8_t chip_platform_type;
+
+ /*
+ * This field returns the maximum value of request window that is
+ * supported by the HWRM. The request window is mapped into device
+ * address space using MMIO.
+ */
+ uint16_t max_req_win_len;
+
+ /*
+ * This field returns the maximum value of response buffer in bytes. If
+ * a request specifies the response buffer length that is greater than
+ * this value, then the HWRM should fail it. The value of this field
+ * shall be 4KB or more.
+ */
+ uint16_t max_resp_len;
+
+ /*
+ * This field returns the default request timeout value in milliseconds.
+ */
+ uint16_t def_req_timeout;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_queue_qportcfg */
+/*
+ * Description: This function is called by a driver to query queue configuration
+ * of a port. # The HWRM shall at least advertise one queue with lossy service
+ * profile. # The driver shall use this command to query queue ids before
+ * configuring or using any queues. # If a service profile is not set for a
+ * queue, then the driver shall not use that queue without configuring a service
+ * profile for it. # If the driver is not allowed to configure service profiles,
+ * then the driver shall only use queues for which service profiles are pre-
+ * configured.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_queue_qportcfg_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both TX and RX
+ * paths of the chip.
+ */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH \
+ UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX \
+ (UINT32_C(0x0) << 0)
+ /* rx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX \
+ (UINT32_C(0x1) << 0)
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX
+ uint32_t flags;
+
+ /*
+ * Port ID of port for which the queue configuration is being queried.
+ * This field is only required when sent by IPC.
+ */
+ uint16_t port_id;
+
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* hwrm_ring_alloc */
+/*
+ * Description: This command allocates and does basic preparation for a ring.
+ */
+
+/* Input (80 bytes) */
+struct hwrm_ring_alloc_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* This bit must be '1' for the Reserved1 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED1 UINT32_C(0x1)
+ /* This bit must be '1' for the Reserved2 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED2 UINT32_C(0x2)
+ /* This bit must be '1' for the Reserved3 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED3 UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the stat_ctx_id_valid field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID UINT32_C(0x8)
+ /* This bit must be '1' for the Reserved4 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED4 UINT32_C(0x10)
+ /* This bit must be '1' for the max_bw_valid field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID UINT32_C(0x20)
+ uint32_t enables;
+
+ /* Ring Type. */
+ /* Completion Ring (CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_CMPL (UINT32_C(0x0) << 0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX (UINT32_C(0x1) << 0)
+ /* RX Ring (RR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX (UINT32_C(0x2) << 0)
+ uint8_t ring_type;
+
+ uint8_t unused_0;
+ uint16_t unused_1;
+
+ /* This value is a pointer to the page table for the Ring. */
+ uint64_t page_tbl_addr;
+
+ /* First Byte Offset of the first entry in the first page. */
+ uint32_t fbo;
+
+ /*
+ * Actual page size in 2^page_size. The supported range is increments in
+ * powers of 2 from 16 bytes to 1GB. - 4 = 16 B Page size is 16 B. - 12
+ * = 4 KB Page size is 4 KB. - 13 = 8 KB Page size is 8 KB. - 16 = 64 KB
+ * Page size is 64 KB. - 22 = 2 MB Page size is 2 MB. - 23 = 4 MB Page
+ * size is 4 MB. - 31 = 1 GB Page size is 1 GB.
+ */
+ uint8_t page_size;
+
+ /*
+ * This value indicates the depth of page table. For this version of the
+ * specification, value other than 0 or 1 shall be considered as an
+ * invalid value. When the page_tbl_depth = 0, then it is treated as a
+ * special case with the following. 1. FBO and page size fields are not
+ * valid. 2. page_tbl_addr is the physical address of the first element
+ * of the ring.
+ */
+ uint8_t page_tbl_depth;
+
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * Number of 16B units in the ring. Minimum size for a ring is 16 16B
+ * entries.
+ */
+ uint32_t length;
+
+ /*
+ * Logical ring number for the ring to be allocated. This value
+ * determines the position in the doorbell area where the update to the
+ * ring will be made. For completion rings, this value is also the MSI-X
+ * vector number for the function the completion ring is associated
+ * with.
+ */
+ uint16_t logical_id;
+
+ /*
+ * This field is used only when ring_type is a TX ring. This value
+ * indicates what completion ring the TX ring is associated with.
+ */
+ uint16_t cmpl_ring_id;
+
+ /*
+ * This field is used only when ring_type is a TX ring. This value
+ * indicates what CoS queue the TX ring is associated with.
+ */
+ uint16_t queue_id;
+
+ uint8_t unused_4;
+ uint8_t unused_5;
+
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t reserved1;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint16_t reserved2;
+
+ uint8_t unused_6;
+ uint8_t unused_7;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t reserved3;
+
+ /*
+ * This field is used only when ring_type is a TX ring. This input
+ * indicates what statistics context this ring should be associated
+ * with.
+ */
+ uint32_t stat_ctx_id;
+
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t reserved4;
+
+ /*
+ * This field is used only when ring_type is a TX ring. Maximum BW
+ * allocated to this TX ring in Mbps. The HWRM will translate this value
+ * into byte counter and time interval used for this ring inside the
+ * device.
+ */
+ uint32_t max_bw;
+
+ /*
+ * This field is used only when ring_type is a Completion ring. This
+ * value indicates what interrupt mode should be used on this completion
+ * ring. Note: In the legacy interrupt mode, no more than 16 completion
+ * rings are allowed.
+ */
+ /* Legacy INTA */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY (UINT32_C(0x0) << 0)
+ /* Reserved */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD (UINT32_C(0x1) << 0)
+ /* MSI-X */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX (UINT32_C(0x2) << 0)
+ /* No Interrupt - Polled mode */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL (UINT32_C(0x3) << 0)
+ uint8_t int_mode;
+
+ uint8_t unused_8[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+
+struct hwrm_ring_alloc_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* Physical number of ring allocated. */
+ uint16_t ring_id;
+
+ /* Logical number of ring allocated. */
+ uint16_t logical_ring_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_ring_free */
+/*
+ * Description: This command is used to free a ring and associated resources.
+ */
+/* Input (24 bytes) */
+
+struct hwrm_ring_free_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* Ring Type. */
+ /* Completion Ring (CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_CMPL (UINT32_C(0x0) << 0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_TX (UINT32_C(0x1) << 0)
+ /* RX Ring (RR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_RX (UINT32_C(0x2) << 0)
+ uint8_t ring_type;
+
+ uint8_t unused_0;
+
+ /* Physical number of ring allocated. */
+ uint16_t ring_id;
+
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_free_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_ring_grp_alloc */
+/*
+ * Description: This API allocates and does basic preparation for a ring group.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_ring_grp_alloc_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* This value identifies the CR associated with the ring group. */
+ uint16_t cr;
+
+ /* This value identifies the main RR associated with the ring group. */
+ uint16_t rr;
+
+ /*
+ * This value identifies the aggregation RR associated with the ring
+ * group. If this value is 0xFF... (All Fs), then no Aggregation ring
+ * will be set.
+ */
+ uint16_t ar;
+
+ /*
+ * This value identifies the statistics context associated with the ring
+ * group.
+ */
+ uint16_t sc;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_grp_alloc_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /*
+ * This is the ring group ID value. Use this value to program the
+ * default ring group for the VNIC or as table entries in an RSS/COS
+ * context.
+ */
+ uint32_t ring_group_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_ring_grp_free */
+/*
+ * Description: This API frees a ring group and associated resources. # If a
+ * ring in the ring group is reset or free, then the associated rings in the
+ * ring group shall also be reset/free using hwrm_ring_free. # A function driver
+ * shall always use hwrm_ring_grp_free after freeing all rings in a group. # As
+ * a part of executing this command, the HWRM shall reset all associated ring
+ * group resources.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_ring_grp_free_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* This is the ring group ID value. */
+ uint32_t ring_group_id;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_grp_free_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_alloc */
+/*
+ * Description: This command allocates and does basic preparation for a stat
+ * context.
+ */
+
+/* Input (32 bytes) */
+struct hwrm_stat_ctx_alloc_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* This is the address for statistic block. */
+ uint64_t stats_dma_addr;
+
+ /*
+ * The statistic block update period in ms. e.g. 250ms, 500ms, 750ms,
+ * 1000ms.
+ */
+ uint32_t update_period_ms;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_alloc_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* This is the statistics context ID value. */
+ uint32_t stat_ctx_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_clr_stats */
+/* Description: This command clears statistics of a context. */
+
+/* Input (24 bytes) */
+struct hwrm_stat_ctx_clr_stats_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* ID of the statistics context that is being queried. */
+ uint32_t stat_ctx_id;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_clr_stats_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_free */
+/* Description: This command is used to free a stat context. */
+/* Input (24 bytes) */
+
+struct hwrm_stat_ctx_free_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* ID of the statistics context that is being queried. */
+ uint32_t stat_ctx_id;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+
+struct hwrm_stat_ctx_free_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* This is the statistics context ID value. */
+ uint32_t stat_ctx_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_vnic_alloc */
+/*
+ * Description: This VNIC is a resource in the RX side of the chip that is used
+ * to represent a virtual host "interface". # At the time of VNIC allocation or
+ * configuration, the function can specify whether it wants the requested VNIC
+ * to be the default VNIC for the function or not. # If a function requests
+ * allocation of a VNIC for the first time and a VNIC is successfully allocated
+ * by the HWRM, then the HWRM shall make the allocated VNIC as the default VNIC
+ * for that function. # The default VNIC shall be used for the default action
+ * for a partition or function. # For each VNIC allocated on a function, a
+ * mapping on the RX side to map the allocated VNIC to source virtual interface
+ * shall be performed by the HWRM. This should be hidden to the function driver
+ * requesting the VNIC allocation. This enables broadcast/multicast replication
+ * with source knockout. # If multicast replication with source knockout is
+ * enabled, then the internal VNIC to SVIF mapping data structures shall be
+ * programmed at the time of VNIC allocation.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_vnic_alloc_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is '1', this VNIC is requested to be the default VNIC
+ * for this function.
+ */
+ #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ uint32_t flags;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_alloc_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_vnic_cfg */
+/* Description: Configure the RX VNIC structure. */
+
+/* Input (40 bytes) */
+struct hwrm_vnic_cfg_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is '1', the VNIC is requested to be the default VNIC
+ * for the function.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is being configured to strip VLAN in
+ * the RX path. If set to '0', then VLAN stripping is disabled on this
+ * VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is being configured to buffer receive
+ * packets in the hardware until the host posts new receive buffers. If
+ * set to '0', then bd_stall is being configured to be disabled on this
+ * VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is being configured to receive both
+ * RoCE and non-RoCE traffic. If set to '0', then this VNIC is not
+ * configured to be operating in dual VNIC mode.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is requested to be configured
+ * to receive only RoCE traffic. If this flag is set to '0', then this
+ * flag shall be ignored by the HWRM. If roce_dual_vnic_mode flag is set
+ * to '1', then the HWRM client shall not set this flag to '1'.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
+ uint32_t flags;
+
+ /* This bit must be '1' for the dflt_ring_grp field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP UINT32_C(0x1)
+ /* This bit must be '1' for the rss_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE UINT32_C(0x2)
+ /* This bit must be '1' for the cos_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE UINT32_C(0x4)
+ /* This bit must be '1' for the lb_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE UINT32_C(0x8)
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU UINT32_C(0x10)
+ uint32_t enables;
+
+ /* Logical vnic ID */
+ uint16_t vnic_id;
+
+ /*
+ * Default Completion ring for the VNIC. This ring will be chosen if
+ * packet does not match any RSS rules and if there is no COS rule.
+ */
+ uint16_t dflt_ring_grp;
+
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if there is no
+ * RSS rule.
+ */
+ uint16_t rss_rule;
+
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if there is no
+ * COS rule.
+ */
+ uint16_t cos_rule;
+
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All Fs) if
+ * there is no LB rule.
+ */
+ uint16_t lb_rule;
+
+ /*
+ * The maximum receive unit of the vnic. Each vnic is associated with a
+ * function. The vnic mru value overwrites the mru setting of the
+ * associated function. The HWRM shall make sure that vnic mru does not
+ * exceed the mru of the port the function is associated with.
+ */
+ uint16_t mru;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_cfg_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_vnic_free */
+/*
+ * Description: Free a VNIC resource. Idle any resources associated with the
+ * VNIC as well as the VNIC. Reset and release all resources associated with the
+ * VNIC.
+ */
+
+/* Input (24 bytes) */
+struct hwrm_vnic_free_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_free_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cfg */
+/* Description: This function is used to enable RSS configuration. */
+
+/* Input (48 bytes) */
+struct hwrm_vnic_rss_cfg_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is '1', the RSS hash shall be computed over source and
+ * destination IPv4 addresses of IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 UINT32_C(0x1)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination ports of
+ * TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination ports of
+ * UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over source and
+ * destination IPv4 addresses of IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination ports of
+ * TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination ports of
+ * UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20)
+ uint32_t hash_type;
+
+ uint32_t unused_0;
+
+ /* This is the address for rss ring group table */
+ uint64_t ring_grp_tbl_addr;
+
+ /* This is the address for rss hash key table */
+ uint64_t hash_key_tbl_addr;
+
+ /* Index to the rss indirection table. */
+ uint16_t rss_ctx_idx;
+
+ uint16_t unused_1[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cfg_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* Input (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint16_t rss_cos_lb_ctx_id;
+
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cos_lb_ctx_free */
+/* Description: This function can be used to free COS/Load Balance context. */
+/* Input (24 bytes) */
+
+struct hwrm_vnic_rss_cos_lb_ctx_free_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint16_t rss_cos_lb_ctx_id;
+
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_queue_qportcfg_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ /* The maximum number of queues that can be configured. */
+ uint8_t max_configurable_queues;
+
+ /* The maximum number of lossless queues that can be configured. */
+ uint8_t max_configurable_lossless_queues;
+
+ /*
+ * 0 - Not allowed. Non-zero - Allowed. If this value is non-zero, then
+ * the HWRM shall allow the host SW driver to configure queues using
+ * hwrm_queue_cfg.
+ */
+ uint8_t queue_cfg_allowed;
+
+ /*
+ * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then
+ * the HWRM shall allow the host SW driver to configure queue buffers
+ * using hwrm_queue_buffers_cfg.
+ */
+ uint8_t queue_buffers_cfg_allowed;
+
+ /*
+ * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then
+ * the HWRM shall allow the host SW driver to configure PFC using
+ * hwrm_queue_pfcenable_cfg.
+ */
+ uint8_t queue_pfcenable_cfg_allowed;
+
+ /*
+ * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then
+ * the HWRM shall allow the host SW driver to configure Priority to CoS
+ * mapping using hwrm_queue_pri2cos_cfg.
+ */
+ uint8_t queue_pri2cos_cfg_allowed;
+
+ /*
+ * 0 - Not allowed. Non-zero - Allowed If this value is non-zero, then
+ * the HWRM shall allow the host SW driver to configure CoS Bandwidth
+ * configuration using hwrm_queue_cos2bw_cfg.
+ */
+ uint8_t queue_cos2bw_cfg_allowed;
+
+ /* ID of CoS Queue 0. FF - Invalid id */
+ uint8_t queue_id0;
+
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id0_service_profile;
+
+ /* ID of CoS Queue 1. FF - Invalid id */
+ uint8_t queue_id1;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id1_service_profile;
+
+ /* ID of CoS Queue 2. FF - Invalid id */
+ uint8_t queue_id2;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id2_service_profile;
+
+ /* ID of CoS Queue 3. FF - Invalid id */
+ uint8_t queue_id3;
+
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id3_service_profile;
+
+ /* ID of CoS Queue 4. FF - Invalid id */
+ uint8_t queue_id4;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id4_service_profile;
+
+ /* ID of CoS Queue 5. FF - Invalid id */
+ uint8_t queue_id5;
+
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id5_service_profile;
+
+ /* ID of CoS Queue 6. FF - Invalid id */
+ uint8_t queue_id6_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id6;
+
+ /* ID of CoS Queue 7. FF - Invalid id */
+ uint8_t queue_id7;
+
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \
+ (UINT32_C(0x0) << 0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Set to 0xFF... (All Fs) if there is no service profile
+ * specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
+ (UINT32_C(0xff) << 0)
+ uint8_t queue_id7_service_profile;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_func_drv_rgtr */
+/*
+ * Description: This command is used by the function driver to register its
+ * information with the HWRM. A function driver shall implement this command. A
+ * function driver shall use this command during the driver initialization right
+ * after the HWRM version discovery and default ring resources allocation.
+ */
+
+/* Input (80 bytes) */
+struct hwrm_func_drv_rgtr_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is '1', the function driver is requesting all requests
+ * from its children VF drivers to be forwarded to itself. This flag can
+ * only be set by the PF driver. If a VF driver sets this flag, it
+ * should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is requesting none of the requests
+ * from its children VF drivers to be forwarded to itself. This flag can
+ * only be set by the PF driver. If a VF driver sets this flag, it
+ * should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE UINT32_C(0x2)
+ uint32_t flags;
+
+ /* This bit must be '1' for the os_type field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE UINT32_C(0x1)
+ /* This bit must be '1' for the ver field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER UINT32_C(0x2)
+ /* This bit must be '1' for the timestamp field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP UINT32_C(0x4)
+ /* This bit must be '1' for the vf_req_fwd field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_REQ_FWD UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the async_event_fwd field to be configured.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD \
+ UINT32_C(0x10)
+ uint32_t enables;
+
+ /* This value indicates the type of OS. */
+ /* Unknown */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 0)
+ /* Other OS not listed below. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER \
+ (UINT32_C(0x1) << 0)
+ /* MSDOS OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS \
+ (UINT32_C(0xe) << 0)
+ /* Windows OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS \
+ (UINT32_C(0x12) << 0)
+ /* Solaris OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS \
+ (UINT32_C(0x1d) << 0)
+ /* Linux OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX \
+ (UINT32_C(0x24) << 0)
+ /* FreeBSD OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD \
+ (UINT32_C(0x2a) << 0)
+ /* VMware ESXi OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI \
+ (UINT32_C(0x68) << 0)
+ /* Microsoft Windows 8 64-bit OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864 \
+ (UINT32_C(0x73) << 0)
+ /* Microsoft Windows Server 2012 R2 OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 \
+ (UINT32_C(0x74) << 0)
+ uint16_t os_type;
+
+ /* This is the major version of the driver. */
+ uint8_t ver_maj;
+
+ /* This is the minor version of the driver. */
+ uint8_t ver_min;
+
+ /* This is the update version of the driver. */
+ uint8_t ver_upd;
+
+ uint8_t unused_0;
+ uint16_t unused_1;
+
+ /*
+ * This is a 32-bit timestamp provided by the driver for keep alive. The
+ * timestamp is in multiples of 1ms.
+ */
+ uint32_t timestamp;
+
+ uint32_t unused_2;
+
+ /*
+ * This is a 256-bit bit mask provided by the PF driver for letting the
+ * HWRM know what commands issued by the VF driver to the HWRM should be
+ * forwarded to the PF driver. Nth bit refers to the Nth req_type.
+ * Setting Nth bit to 1 indicates that requests from the VF driver with
+ * req_type equal to N shall be forwarded to the parent PF driver. This
+ * field is not valid for the VF driver.
+ */
+ uint32_t vf_req_fwd[8];
+
+ /*
+ * This is a 256-bit bit mask provided by the function driver (PF or VF
+ * driver) to indicate the list of asynchronous event completions to be
+ * forwarded. Nth bit refers to the Nth event_id. Setting Nth bit to 1
+ * by the function driver shall result in the HWRM forwarding
+ * asynchronous event completion with event_id equal to N. If all bits
+ * are set to 0 (value of 0), then the HWRM shall not forward any
+ * asynchronous event completion to this function driver.
+ */
+ uint32_t async_event_fwd[8];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+
+struct hwrm_func_drv_rgtr_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_func_drv_unrgtr */
+/*
+ * Description: This command is used by the function driver to un register with
+ * the HWRM. A function driver shall implement this command. A function driver
+ * shall use this command during the driver unloading.
+ */
+/* Input (24 bytes) */
+
+struct hwrm_func_drv_unrgtr_input {
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t req_type;
+
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t cmpl_ring;
+
+ /* This value indicates the command sequence number. */
+ uint16_t seq_id;
+
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint64_t resp_addr;
+
+ /*
+ * When this bit is '1', the function driver is notifying the HWRM to
+ * prepare for the shutdown.
+ */
+ #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN \
+ UINT32_C(0x1)
+ uint32_t flags;
+
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_unrgtr_output {
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t error_code;
+
+ /* This field returns the type of original request. */
+ uint16_t req_type;
+
+ /* This field provides original sequence number of the command. */
+ uint16_t seq_id;
+
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint16_t resp_len;
+
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+#endif
Code Review / deb_dpdk.git / blobdiff