#include "ixgbe_phy.h"
STATIC s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed);
-static s32 ixgbe_acquire_swfw_sync_X550a(struct ixgbe_hw *, u32 mask);
-static void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *, u32 mask);
+STATIC s32 ixgbe_acquire_swfw_sync_X550a(struct ixgbe_hw *, u32 mask);
+STATIC void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *, u32 mask);
/**
* ixgbe_init_ops_X550 - Inits func ptrs and MAC type
IXGBE_WRITE_FLUSH(hw);
}
+/**
+ * ixgbe_read_phy_reg_mdi_22 - Read from a clause 22 PHY register without lock
+ * @hw: pointer to hardware structure
+ * @reg_addr: 32 bit address of PHY register to read
+ * @dev_type: always unused
+ * @phy_data: Pointer to read data from PHY register
+ */
+STATIC s32 ixgbe_read_phy_reg_mdi_22(struct ixgbe_hw *hw, u32 reg_addr,
+ u32 dev_type, u16 *phy_data)
+{
+ u32 i, data, command;
+ UNREFERENCED_1PARAMETER(dev_type);
+
+ /* Setup and write the read command */
+ command = (reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
+ (reg_addr << IXGBE_MSCA_DEV_TYPE_SHIFT) |
+ (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ IXGBE_MSCA_OLD_PROTOCOL | IXGBE_MSCA_READ |
+ IXGBE_MSCA_MDI_COMMAND;
+
+ IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
+
+ /* Check every 10 usec to see if the access completed.
+ * The MDI Command bit will clear when the operation is
+ * complete
+ */
+ for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) {
+ usec_delay(10);
+
+ command = IXGBE_READ_REG(hw, IXGBE_MSCA);
+ if (!(command & IXGBE_MSCA_MDI_COMMAND))
+ break;
+ }
+
+ if (command & IXGBE_MSCA_MDI_COMMAND) {
+ ERROR_REPORT1(IXGBE_ERROR_POLLING,
+ "PHY read command did not complete.\n");
+ return IXGBE_ERR_PHY;
+ }
+
+ /* Read operation is complete. Get the data from MSRWD */
+ data = IXGBE_READ_REG(hw, IXGBE_MSRWD);
+ data >>= IXGBE_MSRWD_READ_DATA_SHIFT;
+ *phy_data = (u16)data;
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_write_phy_reg_mdi_22 - Write to a clause 22 PHY register without lock
+ * @hw: pointer to hardware structure
+ * @reg_addr: 32 bit PHY register to write
+ * @dev_type: always unused
+ * @phy_data: Data to write to the PHY register
+ */
+STATIC s32 ixgbe_write_phy_reg_mdi_22(struct ixgbe_hw *hw, u32 reg_addr,
+ u32 dev_type, u16 phy_data)
+{
+ u32 i, command;
+ UNREFERENCED_1PARAMETER(dev_type);
+
+ /* Put the data in the MDI single read and write data register*/
+ IXGBE_WRITE_REG(hw, IXGBE_MSRWD, (u32)phy_data);
+
+ /* Setup and write the write command */
+ command = (reg_addr << IXGBE_MSCA_NP_ADDR_SHIFT) |
+ (reg_addr << IXGBE_MSCA_DEV_TYPE_SHIFT) |
+ (hw->phy.addr << IXGBE_MSCA_PHY_ADDR_SHIFT) |
+ IXGBE_MSCA_OLD_PROTOCOL | IXGBE_MSCA_WRITE |
+ IXGBE_MSCA_MDI_COMMAND;
+
+ IXGBE_WRITE_REG(hw, IXGBE_MSCA, command);
+
+ /* Check every 10 usec to see if the access completed.
+ * The MDI Command bit will clear when the operation is
+ * complete
+ */
+ for (i = 0; i < IXGBE_MDIO_COMMAND_TIMEOUT; i++) {
+ usec_delay(10);
+
+ command = IXGBE_READ_REG(hw, IXGBE_MSCA);
+ if (!(command & IXGBE_MSCA_MDI_COMMAND))
+ break;
+ }
+
+ if (command & IXGBE_MSCA_MDI_COMMAND) {
+ ERROR_REPORT1(IXGBE_ERROR_POLLING,
+ "PHY write cmd didn't complete\n");
+ return IXGBE_ERR_PHY;
+ }
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_identify_phy_1g - Get 1g PHY type based on device id
+ * @hw: pointer to hardware structure
+ *
+ * Returns error code
+ */
+STATIC s32 ixgbe_identify_phy_1g(struct ixgbe_hw *hw)
+{
+ u32 swfw_mask = hw->phy.phy_semaphore_mask;
+ u16 phy_id_high;
+ u16 phy_id_low;
+ s32 rc;
+
+ rc = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask);
+ if (rc)
+ return rc;
+
+ rc = ixgbe_read_phy_reg_mdi_22(hw, IXGBE_MDIO_PHY_ID_HIGH, 0,
+ &phy_id_high);
+ if (rc)
+ goto rel_out;
+
+ rc = ixgbe_read_phy_reg_mdi_22(hw, IXGBE_MDIO_PHY_ID_LOW, 0,
+ &phy_id_low);
+ if (rc)
+ goto rel_out;
+
+ hw->phy.id = (u32)phy_id_high << 16;
+ hw->phy.id |= phy_id_low & IXGBE_PHY_REVISION_MASK;
+ hw->phy.revision = (u32)phy_id_low & ~IXGBE_PHY_REVISION_MASK;
+
+rel_out:
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+
+ return rc;
+}
+
/**
* ixgbe_identify_phy_x550em - Get PHY type based on device id
* @hw: pointer to hardware structure
{
switch (hw->device_id) {
case IXGBE_DEV_ID_X550EM_A_SFP:
- hw->phy.phy_semaphore_mask = IXGBE_GSSR_TOKEN_SM;
+ hw->phy.ops.read_reg = ixgbe_read_phy_reg_x550a;
+ hw->phy.ops.write_reg = ixgbe_write_phy_reg_x550a;
if (hw->bus.lan_id)
hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM;
else
break;
case IXGBE_DEV_ID_X550EM_X_1G_T:
case IXGBE_DEV_ID_X550EM_X_10G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T:
- case IXGBE_DEV_ID_X550EM_A_1G_T_L:
case IXGBE_DEV_ID_X550EM_A_10G_T:
return ixgbe_identify_phy_generic(hw);
+ case IXGBE_DEV_ID_X550EM_A_1G_T:
+ case IXGBE_DEV_ID_X550EM_A_1G_T_L:
+ hw->phy.ops.read_reg = ixgbe_read_phy_reg_x550a;
+ hw->phy.ops.write_reg = ixgbe_write_phy_reg_x550a;
+ if (hw->bus.lan_id)
+ hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM;
+ else
+ hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY0_SM;
+ return ixgbe_identify_phy_1g(hw);
default:
break;
}
*
* Returns an error code on error.
**/
-static s32 ixgbe_read_i2c_combined_generic(struct ixgbe_hw *hw, u8 addr,
+STATIC s32 ixgbe_read_i2c_combined_generic(struct ixgbe_hw *hw, u8 addr,
u16 reg, u16 *val)
{
return ixgbe_read_i2c_combined_generic_int(hw, addr, reg, val, true);
*
* Returns an error code on error.
**/
-static s32
+STATIC s32
ixgbe_read_i2c_combined_generic_unlocked(struct ixgbe_hw *hw, u8 addr,
u16 reg, u16 *val)
{
*
* Returns an error code on error.
**/
-static s32 ixgbe_write_i2c_combined_generic(struct ixgbe_hw *hw,
+STATIC s32 ixgbe_write_i2c_combined_generic(struct ixgbe_hw *hw,
u8 addr, u16 reg, u16 val)
{
return ixgbe_write_i2c_combined_generic_int(hw, addr, reg, val, true);
*
* Returns an error code on error.
**/
-static s32
+STATIC s32
ixgbe_write_i2c_combined_generic_unlocked(struct ixgbe_hw *hw,
u8 addr, u16 reg, u16 val)
{
link->addr = IXGBE_CS4227;
}
if (hw->mac.type == ixgbe_mac_X550EM_a) {
- mac->ops.read_iosf_sb_reg = ixgbe_read_iosf_sb_reg_x550a;
- mac->ops.write_iosf_sb_reg = ixgbe_write_iosf_sb_reg_x550a;
+ mac->ops.read_iosf_sb_reg = ixgbe_read_iosf_sb_reg_x550;
+ mac->ops.write_iosf_sb_reg = ixgbe_write_iosf_sb_reg_x550;
mac->ops.acquire_swfw_sync = ixgbe_acquire_swfw_sync_X550a;
mac->ops.release_swfw_sync = ixgbe_release_swfw_sync_X550a;
}
if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper)
mac->ops.setup_fc = ixgbe_setup_fc_generic;
+ else if (hw->mac.type == ixgbe_mac_X550EM_a) {
+ mac->ops.setup_fc = ixgbe_setup_fc_x550a;
+ mac->ops.fc_autoneg = ixgbe_fc_autoneg_x550a;
+ }
else
mac->ops.setup_fc = ixgbe_setup_fc_X550em;
-
- if (hw->device_id != IXGBE_DEV_ID_X550EM_X_KR)
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_X_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR_L:
+ break;
+ default:
mac->ops.setup_eee = NULL;
+ }
/* PHY */
phy->ops.init = ixgbe_init_phy_ops_X550em;
return IXGBE_SUCCESS;
}
+/**
+ * ixgbe_enable_eee_x550 - Enable EEE support
+ * @hw: pointer to hardware structure
+ */
+STATIC s32 ixgbe_enable_eee_x550(struct ixgbe_hw *hw)
+{
+ u16 autoneg_eee_reg;
+ u32 link_reg;
+ s32 status;
+
+ if (hw->mac.type == ixgbe_mac_X550) {
+ /* Advertise EEE capability */
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_eee_reg);
+
+ autoneg_eee_reg |= (IXGBE_AUTO_NEG_10GBASE_EEE_ADVT |
+ IXGBE_AUTO_NEG_1000BASE_EEE_ADVT |
+ IXGBE_AUTO_NEG_100BASE_EEE_ADVT);
+
+ hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ autoneg_eee_reg);
+ return IXGBE_SUCCESS;
+ }
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_X_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR_L:
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
+ IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX;
+
+ /* Don't advertise FEC capability when EEE enabled. */
+ link_reg &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
+
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ break;
+ default:
+ break;
+ }
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_disable_eee_x550 - Disable EEE support
+ * @hw: pointer to hardware structure
+ */
+STATIC s32 ixgbe_disable_eee_x550(struct ixgbe_hw *hw)
+{
+ u16 autoneg_eee_reg;
+ u32 link_reg;
+ s32 status;
+
+ if (hw->mac.type == ixgbe_mac_X550) {
+ /* Disable advertised EEE capability */
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_eee_reg);
+
+ autoneg_eee_reg &= ~(IXGBE_AUTO_NEG_10GBASE_EEE_ADVT |
+ IXGBE_AUTO_NEG_1000BASE_EEE_ADVT |
+ IXGBE_AUTO_NEG_100BASE_EEE_ADVT);
+
+ hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ autoneg_eee_reg);
+ return IXGBE_SUCCESS;
+ }
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_X_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR_L:
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ link_reg &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
+ IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX);
+
+ /* Advertise FEC capability when EEE is disabled. */
+ link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
+
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ break;
+ default:
+ break;
+ }
+
+ return IXGBE_SUCCESS;
+}
+
/**
* ixgbe_setup_eee_X550 - Enable/disable EEE support
* @hw: pointer to the HW structure
**/
s32 ixgbe_setup_eee_X550(struct ixgbe_hw *hw, bool enable_eee)
{
- u32 eeer;
- u16 autoneg_eee_reg;
- u32 link_reg;
s32 status;
+ u32 eeer;
DEBUGFUNC("ixgbe_setup_eee_X550");
if (enable_eee) {
eeer |= (IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN);
- if (hw->mac.type == ixgbe_mac_X550) {
- /* Advertise EEE capability */
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_eee_reg);
-
- autoneg_eee_reg |= (IXGBE_AUTO_NEG_10GBASE_EEE_ADVT |
- IXGBE_AUTO_NEG_1000BASE_EEE_ADVT |
- IXGBE_AUTO_NEG_100BASE_EEE_ADVT);
-
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_eee_reg);
- } else if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR) {
- /* Not supported on first revision of X550EM_x. */
- if ((hw->mac.type == ixgbe_mac_X550EM_x) &&
- !(IXGBE_FUSES0_REV_MASK &
- IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0))))
- return IXGBE_SUCCESS;
-
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
-
- link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
- IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX;
-
- /* Don't advertise FEC capability when EEE enabled. */
- link_reg &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
-
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
- }
+ /* Not supported on first revision of X550EM_x. */
+ if ((hw->mac.type == ixgbe_mac_X550EM_x) &&
+ !(IXGBE_FUSES0_REV_MASK &
+ IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0))))
+ return IXGBE_SUCCESS;
+ status = ixgbe_enable_eee_x550(hw);
+ if (status)
+ return status;
} else {
eeer &= ~(IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN);
- if (hw->mac.type == ixgbe_mac_X550) {
- /* Disable advertised EEE capability */
- hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_eee_reg);
-
- autoneg_eee_reg &= ~(IXGBE_AUTO_NEG_10GBASE_EEE_ADVT |
- IXGBE_AUTO_NEG_1000BASE_EEE_ADVT |
- IXGBE_AUTO_NEG_100BASE_EEE_ADVT);
-
- hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT,
- IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_eee_reg);
- } else if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR) {
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
-
- link_reg &= ~(IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR |
- IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX);
-
- /* Advertise FEC capability when EEE is disabled. */
- link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC;
-
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg);
- if (status != IXGBE_SUCCESS)
- return status;
- }
+ status = ixgbe_disable_eee_x550(hw);
+ if (status)
+ return status;
}
IXGBE_WRITE_REG(hw, IXGBE_EEER, eeer);
token_cmd.hdr.cmd = FW_PHY_TOKEN_REQ_CMD;
token_cmd.hdr.buf_len = FW_PHY_TOKEN_REQ_LEN;
token_cmd.hdr.cmd_or_resp.cmd_resv = 0;
+ token_cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
token_cmd.port_number = hw->bus.lan_id;
token_cmd.command_type = FW_PHY_TOKEN_REQ;
token_cmd.pad = 0;
token_cmd.hdr.cmd = FW_PHY_TOKEN_REQ_CMD;
token_cmd.hdr.buf_len = FW_PHY_TOKEN_REQ_LEN;
token_cmd.hdr.cmd_or_resp.cmd_resv = 0;
+ token_cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
token_cmd.port_number = hw->bus.lan_id;
token_cmd.command_type = FW_PHY_TOKEN_REL;
token_cmd.pad = 0;
return status;
if (token_cmd.hdr.cmd_or_resp.ret_status == FW_PHY_TOKEN_OK)
return IXGBE_SUCCESS;
+
+ DEBUGOUT("Put PHY Token host interface command failed");
return IXGBE_ERR_FW_RESP_INVALID;
}
* @data: Data to write to the register
**/
s32 ixgbe_write_iosf_sb_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
- u32 device_type, u32 data)
+ u32 device_type, u32 data)
{
struct ixgbe_hic_internal_phy_req write_cmd;
s32 status;
UNREFERENCED_1PARAMETER(device_type);
+ memset(&write_cmd, 0, sizeof(write_cmd));
write_cmd.hdr.cmd = FW_INT_PHY_REQ_CMD;
write_cmd.hdr.buf_len = FW_INT_PHY_REQ_LEN;
+ write_cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
write_cmd.port_number = hw->bus.lan_id;
write_cmd.command_type = FW_INT_PHY_REQ_WRITE;
- write_cmd.address = (u16)reg_addr;
- write_cmd.rsv1 = 0;
- write_cmd.write_data = data;
- write_cmd.pad = 0;
+ write_cmd.address = IXGBE_CPU_TO_BE16(reg_addr);
+ write_cmd.write_data = IXGBE_CPU_TO_LE32(data);
status = ixgbe_host_interface_command(hw, (u32 *)&write_cmd,
- sizeof(write_cmd), IXGBE_HI_COMMAND_TIMEOUT, false);
+ sizeof(write_cmd),
+ IXGBE_HI_COMMAND_TIMEOUT, false);
return status;
}
* @data: Pointer to read data from the register
**/
s32 ixgbe_read_iosf_sb_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
- u32 device_type, u32 *data)
+ u32 device_type, u32 *data)
{
- struct ixgbe_hic_internal_phy_req read_cmd;
+ union {
+ struct ixgbe_hic_internal_phy_req cmd;
+ struct ixgbe_hic_internal_phy_resp rsp;
+ } hic;
s32 status;
UNREFERENCED_1PARAMETER(device_type);
- read_cmd.hdr.cmd = FW_INT_PHY_REQ_CMD;
- read_cmd.hdr.buf_len = FW_INT_PHY_REQ_LEN;
- read_cmd.port_number = hw->bus.lan_id;
- read_cmd.command_type = FW_INT_PHY_REQ_READ;
- read_cmd.address = (u16)reg_addr;
- read_cmd.rsv1 = 0;
- read_cmd.write_data = 0;
- read_cmd.pad = 0;
+ memset(&hic, 0, sizeof(hic));
+ hic.cmd.hdr.cmd = FW_INT_PHY_REQ_CMD;
+ hic.cmd.hdr.buf_len = FW_INT_PHY_REQ_LEN;
+ hic.cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
+ hic.cmd.port_number = hw->bus.lan_id;
+ hic.cmd.command_type = FW_INT_PHY_REQ_READ;
+ hic.cmd.address = IXGBE_CPU_TO_BE16(reg_addr);
- status = ixgbe_host_interface_command(hw, (u32 *)&read_cmd,
- sizeof(read_cmd), IXGBE_HI_COMMAND_TIMEOUT, true);
+ status = ixgbe_host_interface_command(hw, (u32 *)&hic.cmd,
+ sizeof(hic.cmd),
+ IXGBE_HI_COMMAND_TIMEOUT, true);
/* Extract the register value from the response. */
- *data = ((struct ixgbe_hic_internal_phy_resp *)&read_cmd)->read_data;
+ *data = IXGBE_LE32_TO_CPU(hic.rsp.read_data);
return status;
}
break;
case IXGBE_DEV_ID_X550EM_X_1G_T:
case IXGBE_DEV_ID_X550EM_X_10G_T:
+ case IXGBE_DEV_ID_X550EM_A_10G_T:
+ media_type = ixgbe_media_type_copper;
+ break;
+ case IXGBE_DEV_ID_X550EM_A_SGMII:
+ case IXGBE_DEV_ID_X550EM_A_SGMII_L:
+ media_type = ixgbe_media_type_backplane;
+ hw->phy.type = ixgbe_phy_sgmii;
+ break;
case IXGBE_DEV_ID_X550EM_A_1G_T:
case IXGBE_DEV_ID_X550EM_A_1G_T_L:
- case IXGBE_DEV_ID_X550EM_A_10G_T:
media_type = ixgbe_media_type_copper;
+ hw->phy.type = ixgbe_phy_m88;
break;
default:
media_type = ixgbe_media_type_unknown;
return IXGBE_SUCCESS;
}
+/**
+ * ixgbe_setup_sgmii - Set up link for sgmii
+ * @hw: pointer to hardware structure
+ */
+STATIC s32 ixgbe_setup_sgmii(struct ixgbe_hw *hw, ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ u32 lval, sval;
+ s32 rc;
+ UNREFERENCED_2PARAMETER(speed, autoneg_wait_to_complete);
+
+ rc = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &lval);
+ if (rc)
+ return rc;
+
+ lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+ lval &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
+ lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_SGMII_EN;
+ lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CLAUSE_37_EN;
+ lval |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G;
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, lval);
+ if (rc)
+ return rc;
+
+ rc = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_SGMII_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &sval);
+ if (rc)
+ return rc;
+
+ sval |= IXGBE_KRM_SGMII_CTRL_MAC_TAR_FORCE_10_D;
+ sval |= IXGBE_KRM_SGMII_CTRL_MAC_TAR_FORCE_100_D;
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_SGMII_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, sval);
+ if (rc)
+ return rc;
+
+ lval |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
+ rc = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, lval);
+
+ return rc;
+}
+
/**
* ixgbe_init_mac_link_ops_X550em - init mac link function pointers
* @hw: pointer to hardware structure
DEBUGFUNC("ixgbe_init_mac_link_ops_X550em");
- switch (hw->mac.ops.get_media_type(hw)) {
- case ixgbe_media_type_fiber:
+ switch (hw->mac.ops.get_media_type(hw)) {
+ case ixgbe_media_type_fiber:
/* CS4227 does not support autoneg, so disable the laser control
* functions for SFP+ fiber
*/
mac->ops.enable_tx_laser = NULL;
mac->ops.flap_tx_laser = NULL;
mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber;
- mac->ops.setup_mac_link = ixgbe_setup_mac_link_sfp_x550em;
mac->ops.set_rate_select_speed =
ixgbe_set_soft_rate_select_speed;
+ if ((hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP_N) ||
+ (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP))
+ mac->ops.setup_mac_link =
+ ixgbe_setup_mac_link_sfp_x550a;
+ else
+ mac->ops.setup_mac_link =
+ ixgbe_setup_mac_link_sfp_x550em;
break;
case ixgbe_media_type_copper:
mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em;
mac->ops.check_link = ixgbe_check_link_t_X550em;
break;
+ case ixgbe_media_type_backplane:
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_SGMII_L)
+ mac->ops.setup_link = ixgbe_setup_sgmii;
+ break;
default:
break;
- }
+ }
}
/**
else
*speed = IXGBE_LINK_SPEED_10GB_FULL;
} else {
- *speed = IXGBE_LINK_SPEED_10GB_FULL |
- IXGBE_LINK_SPEED_1GB_FULL;
+ switch (hw->phy.type) {
+ case ixgbe_phy_m88:
+ *speed = IXGBE_LINK_SPEED_100_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ case ixgbe_phy_sgmii:
+ *speed = IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ default:
+ *speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ }
*autoneg = true;
}
s32 status;
u32 reg_val;
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status)
return status;
/* Restart auto-negotiation. */
reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
return status;
}
+/**
+ * ixgbe_set_master_slave_mode - Set up PHY for master/slave mode
+ * @hw: pointer to hardware structure
+ *
+ * Must be called while holding the PHY semaphore and token
+ */
+STATIC s32 ixgbe_set_master_slave_mode(struct ixgbe_hw *hw)
+{
+ u16 phy_data;
+ s32 rc;
+
+ /* Resolve master/slave mode */
+ rc = ixgbe_read_phy_reg_mdi_22(hw, IXGBE_M88E1500_1000T_CTRL, 0,
+ &phy_data);
+ if (rc)
+ return rc;
+
+ /* load defaults for future use */
+ if (phy_data & IXGBE_M88E1500_1000T_CTRL_MS_ENABLE) {
+ if (phy_data & IXGBE_M88E1500_1000T_CTRL_MS_VALUE)
+ hw->phy.original_ms_type = ixgbe_ms_force_master;
+ else
+ hw->phy.original_ms_type = ixgbe_ms_force_slave;
+ } else {
+ hw->phy.original_ms_type = ixgbe_ms_auto;
+ }
+
+ switch (hw->phy.ms_type) {
+ case ixgbe_ms_force_master:
+ phy_data |= IXGBE_M88E1500_1000T_CTRL_MS_ENABLE;
+ phy_data |= IXGBE_M88E1500_1000T_CTRL_MS_VALUE;
+ break;
+ case ixgbe_ms_force_slave:
+ phy_data |= IXGBE_M88E1500_1000T_CTRL_MS_ENABLE;
+ phy_data &= ~IXGBE_M88E1500_1000T_CTRL_MS_VALUE;
+ break;
+ case ixgbe_ms_auto:
+ phy_data &= ~IXGBE_M88E1500_1000T_CTRL_MS_ENABLE;
+ break;
+ default:
+ break;
+ }
+
+ return ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_1000T_CTRL, 0,
+ phy_data);
+}
+
+/**
+ * ixgbe_reset_phy_m88_nolock - Reset m88 PHY without locking
+ * @hw: pointer to hardware structure
+ *
+ * Must be called while holding the PHY semaphore and token
+ */
+STATIC s32 ixgbe_reset_phy_m88_nolock(struct ixgbe_hw *hw)
+{
+ s32 rc;
+
+ rc = ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1);
+ if (rc)
+ return rc;
+
+ rc = ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_FIBER_CTRL, 0,
+ IXGBE_M88E1500_FIBER_CTRL_RESET |
+ IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL |
+ IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB);
+ if (rc)
+ goto res_out;
+
+ rc = ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 18);
+ if (rc)
+ goto res_out;
+
+ rc = ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_GEN_CTRL, 0,
+ IXGBE_M88E1500_GEN_CTRL_RESET |
+ IXGBE_M88E1500_GEN_CTRL_SGMII_COPPER);
+ if (rc)
+ goto res_out;
+
+ rc = ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
+ if (rc)
+ goto res_out;
+
+ rc = ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_COPPER_CTRL, 0,
+ IXGBE_M88E1500_COPPER_CTRL_RESET |
+ IXGBE_M88E1500_COPPER_CTRL_AN_EN |
+ IXGBE_M88E1500_COPPER_CTRL_RESTART_AN |
+ IXGBE_M88E1500_COPPER_CTRL_FULL_DUPLEX |
+ IXGBE_M88E1500_COPPER_CTRL_SPEED_MSB);
+
+res_out:
+ ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
+ return rc;
+}
+
+/**
+ * ixgbe_reset_phy_m88 - Reset m88 PHY
+ * @hw: pointer to hardware structure
+ */
+STATIC s32 ixgbe_reset_phy_m88(struct ixgbe_hw *hw)
+{
+ u32 swfw_mask = hw->phy.phy_semaphore_mask;
+ s32 rc;
+
+ if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw))
+ return IXGBE_SUCCESS;
+
+ rc = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask);
+ if (rc)
+ return rc;
+
+ rc = ixgbe_reset_phy_m88_nolock(hw);
+
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+ return rc;
+}
+
+/**
+ * ixgbe_setup_m88 - setup m88 PHY
+ * @hw: pointer to hardware structure
+ */
+STATIC s32 ixgbe_setup_m88(struct ixgbe_hw *hw)
+{
+ u32 swfw_mask = hw->phy.phy_semaphore_mask;
+ struct ixgbe_phy_info *phy = &hw->phy;
+ u16 phy_data;
+ s32 rc;
+
+ if (phy->reset_disable || ixgbe_check_reset_blocked(hw))
+ return IXGBE_SUCCESS;
+
+ rc = hw->mac.ops.acquire_swfw_sync(hw, swfw_mask);
+ if (rc)
+ return rc;
+
+ rc = ixgbe_read_phy_reg_mdi_22(hw, IXGBE_M88E1500_PHY_SPEC_CTRL, 0,
+ &phy_data);
+ if (rc)
+ goto rel_out;
+
+ /* Enable downshift and setting it to X6 */
+ phy_data &= ~IXGBE_M88E1500_PSCR_DOWNSHIFT_ENABLE;
+ phy_data |= IXGBE_M88E1500_PSCR_DOWNSHIFT_6X;
+ phy_data |= IXGBE_M88E1500_PSCR_DOWNSHIFT_ENABLE;
+ rc = ixgbe_write_phy_reg_mdi_22(hw,
+ IXGBE_M88E1500_PHY_SPEC_CTRL, 0,
+ phy_data);
+ if (rc)
+ goto rel_out;
+
+ ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
+
+ /* Commit the changes */
+ rc = ixgbe_reset_phy_m88_nolock(hw);
+ if (rc) {
+ DEBUGOUT("Error committing the PHY changes\n");
+ goto rel_out;
+ }
+
+ rc = ixgbe_set_master_slave_mode(hw);
+
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+ return rc;
+
+rel_out:
+ ixgbe_write_phy_reg_mdi_22(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0);
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+ return rc;
+}
+
+/**
+ * ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register
+ * @hw: pointer to hardware structure
+ *
+ * Read NW_MNG_IF_SEL register and save field values, and check for valid field
+ * values.
+ **/
+STATIC s32 ixgbe_read_mng_if_sel_x550em(struct ixgbe_hw *hw)
+{
+ /* Save NW management interface connected on board. This is used
+ * to determine internal PHY mode.
+ */
+ hw->phy.nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
+
+ /* If X552 (X550EM_a) and MDIO is connected to external PHY, then set
+ * PHY address. This register field was has only been used for X552.
+ */
+ if (hw->mac.type == ixgbe_mac_X550EM_a &&
+ hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_MDIO_ACT) {
+ hw->phy.addr = (hw->phy.nw_mng_if_sel &
+ IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD) >>
+ IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD_SHIFT;
+ }
+
+ return IXGBE_SUCCESS;
+}
+
/**
* ixgbe_init_phy_ops_X550em - PHY/SFP specific init
* @hw: pointer to hardware structure
hw->mac.ops.set_lan_id(hw);
+ ixgbe_read_mng_if_sel_x550em(hw);
+
if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) {
phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM;
ixgbe_setup_mux_ctl(hw);
-
- /* Save NW management interface connected on board. This is used
- * to determine internal PHY mode.
- */
- phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
phy->ops.identify_sfp = ixgbe_identify_sfp_module_X550em;
}
phy->ops.write_reg = ixgbe_write_phy_reg_x550em;
break;
case ixgbe_phy_x550em_ext_t:
- /* Save NW management interface connected on board. This is used
- * to determine internal PHY mode
- */
- phy->nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL);
-
/* If internal link mode is XFI, then setup iXFI internal link,
* else setup KR now.
*/
phy->ops.handle_lasi = ixgbe_handle_lasi_ext_t_x550em;
phy->ops.reset = ixgbe_reset_phy_t_X550em;
break;
+ case ixgbe_phy_sgmii:
+ phy->ops.setup_link = NULL;
+ break;
+ case ixgbe_phy_m88:
+ phy->ops.setup_link = ixgbe_setup_m88;
+ phy->ops.read_reg_mdi = ixgbe_read_phy_reg_mdi_22;
+ phy->ops.write_reg_mdi = ixgbe_write_phy_reg_mdi_22;
+ phy->ops.reset = ixgbe_reset_phy_m88;
+ break;
default:
break;
}
* ixgbe_set_mdio_speed - Set MDIO clock speed
* @hw: pointer to hardware structure
*/
-static void ixgbe_set_mdio_speed(struct ixgbe_hw *hw)
+STATIC void ixgbe_set_mdio_speed(struct ixgbe_hw *hw)
{
u32 hlreg0;
switch (hw->device_id) {
case IXGBE_DEV_ID_X550EM_X_10G_T:
+ case IXGBE_DEV_ID_X550EM_A_SGMII:
+ case IXGBE_DEV_ID_X550EM_A_SGMII_L:
case IXGBE_DEV_ID_X550EM_A_1G_T:
case IXGBE_DEV_ID_X550EM_A_1G_T_L:
case IXGBE_DEV_ID_X550EM_A_10G_T:
* ixgbe_setup_kr_x550em - Configure the KR PHY.
* @hw: pointer to hardware structure
*
- * Configures the integrated KR PHY.
+ * Configures the integrated KR PHY for X550EM_x.
**/
s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
{
+ if (hw->mac.type != ixgbe_mac_X550EM_x)
+ return IXGBE_SUCCESS;
+
return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);
}
return ret_val;
}
+/**
+ * ixgbe_setup_mac_link_sfp_x550a - Setup internal PHY for SFP
+ * @hw: pointer to hardware structure
+ *
+ * Configure the the integrated PHY for SFP support.
+ **/
+s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ s32 ret_val;
+ u16 reg_phy_ext;
+ bool setup_linear = false;
+ u32 reg_slice, reg_phy_int, slice_offset;
+
+ UNREFERENCED_1PARAMETER(autoneg_wait_to_complete);
+
+ /* Check if SFP module is supported and linear */
+ ret_val = ixgbe_supported_sfp_modules_X550em(hw, &setup_linear);
+
+ /* If no SFP module present, then return success. Return success since
+ * SFP not present error is not excepted in the setup MAC link flow.
+ */
+ if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT)
+ return IXGBE_SUCCESS;
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP_N) {
+ /* Configure internal PHY for native SFI */
+ ret_val = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_8(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_phy_int);
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ if (setup_linear) {
+ reg_phy_int &= ~IXGBE_KRM_AN_CNTL_8_LIMITING;
+ reg_phy_int |= IXGBE_KRM_AN_CNTL_8_LINEAR;
+ } else {
+ reg_phy_int |= IXGBE_KRM_AN_CNTL_8_LIMITING;
+ reg_phy_int &= ~IXGBE_KRM_AN_CNTL_8_LINEAR;
+ }
+
+ ret_val = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_8(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_phy_int);
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ /* Setup XFI/SFI internal link. */
+ ret_val = ixgbe_setup_ixfi_x550em(hw, &speed);
+ } else {
+ /* Configure internal PHY for KR/KX. */
+ ixgbe_setup_kr_speed_x550em(hw, speed);
+
+ if (hw->phy.addr == 0x0 || hw->phy.addr == 0xFFFF) {
+ /* Find Address */
+ DEBUGOUT("Invalid NW_MNG_IF_SEL.MDIO_PHY_ADD value\n");
+ return IXGBE_ERR_PHY_ADDR_INVALID;
+ }
+
+ /* Get external PHY device id */
+ ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_GLOBAL_ID_MSB,
+ IXGBE_MDIO_ZERO_DEV_TYPE, ®_phy_ext);
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ /* When configuring quad port CS4223, the MAC instance is part
+ * of the slice offset.
+ */
+ if (reg_phy_ext == IXGBE_CS4223_PHY_ID)
+ slice_offset = (hw->bus.lan_id +
+ (hw->bus.instance_id << 1)) << 12;
+ else
+ slice_offset = hw->bus.lan_id << 12;
+
+ /* Configure CS4227/CS4223 LINE side to proper mode. */
+ reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + slice_offset;
+ if (setup_linear)
+ reg_phy_ext = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
+ else
+ reg_phy_ext = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
+ ret_val = hw->phy.ops.write_reg(hw, reg_slice,
+ IXGBE_MDIO_ZERO_DEV_TYPE, reg_phy_ext);
+ }
+ return ret_val;
+}
+
/**
* ixgbe_setup_ixfi_x550em_x - MAC specific iXFI configuration
* @hw: pointer to hardware structure
u32 reg_val;
/* Disable AN and force speed to 10G Serial. */
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G;
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
if (status != IXGBE_SUCCESS)
return status;
/* Set near-end loopback clocks. */
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_32B;
reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_KRPCS;
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
if (status != IXGBE_SUCCESS)
return status;
/* Set loopback enable. */
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val |= IXGBE_KRM_PMD_DFX_BURNIN_TX_RX_KR_LB_MASK;
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
if (status != IXGBE_SUCCESS)
return status;
/* Training bypass. */
- status = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (status != IXGBE_SUCCESS)
return status;
reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_PROTOCOL_BYPASS;
- status = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
return status;
}
goto out;
}
- if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR) {
- ret_val = ixgbe_read_iosf_sb_reg_x550(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_X_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR_L:
+ ret_val = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
if (ret_val != IXGBE_SUCCESS)
goto out;
reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
- IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
if (pause)
reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
if (asm_dir)
reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
- ret_val = ixgbe_write_iosf_sb_reg_x550(hw,
- IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
- IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ ret_val = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
/* This device does not fully support AN. */
hw->fc.disable_fc_autoneg = true;
+ break;
+ default:
+ break;
}
out:
return ret_val;
}
+/**
+ * ixgbe_fc_autoneg_x550a - Enable flow control IEEE clause 37
+ * @hw: pointer to hardware structure
+ *
+ * Enable flow control according to IEEE clause 37.
+ **/
+void ixgbe_fc_autoneg_x550a(struct ixgbe_hw *hw)
+{
+ u32 link_s1, lp_an_page_low, an_cntl_1;
+ s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ ixgbe_link_speed speed;
+ bool link_up;
+
+ /* AN should have completed when the cable was plugged in.
+ * Look for reasons to bail out. Bail out if:
+ * - FC autoneg is disabled, or if
+ * - link is not up.
+ */
+ if (hw->fc.disable_fc_autoneg) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "Flow control autoneg is disabled");
+ goto out;
+ }
+
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ if (!link_up) {
+ ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down");
+ goto out;
+ }
+
+ /* Check at auto-negotiation has completed */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_S1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1);
+
+ if (status != IXGBE_SUCCESS ||
+ (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ goto out;
+ }
+
+ /* Read the 10g AN autoc and LP ability registers and resolve
+ * local flow control settings accordingly
+ */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl_1);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ goto out;
+ }
+
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LP_BASE_PAGE_HIGH(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &lp_an_page_low);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ goto out;
+ }
+
+ status = ixgbe_negotiate_fc(hw, an_cntl_1, lp_an_page_low,
+ IXGBE_KRM_AN_CNTL_1_SYM_PAUSE,
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE,
+ IXGBE_KRM_LP_BASE_PAGE_HIGH_SYM_PAUSE,
+ IXGBE_KRM_LP_BASE_PAGE_HIGH_ASM_PAUSE);
+
+out:
+ if (status == IXGBE_SUCCESS) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
+}
+
+/**
+ * ixgbe_setup_fc_x550em - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ **/
+s32 ixgbe_setup_fc_x550a(struct ixgbe_hw *hw)
+{
+ s32 status = IXGBE_SUCCESS;
+ u32 an_cntl, link_ctrl = 0;
+
+ DEBUGFUNC("ixgbe_setup_fc_x550em");
+
+ /* Validate the requested mode */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ return IXGBE_ERR_INVALID_LINK_SETTINGS;
+ }
+
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /* Set up the 1G and 10G flow control advertisement registers so the
+ * HW will be able to do FC autoneg once the cable is plugged in. If
+ * we link at 10G, the 1G advertisement is harmless and vice versa.
+ */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ return status;
+ }
+
+ /* The possible values of fc.requested_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: Invalid.
+ */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ an_cntl &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /* Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ an_cntl |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ an_cntl &= ~IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
+ break;
+ case ixgbe_fc_rx_pause:
+ /* Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE, as such we fall
+ * through to the fc_full statement. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ an_cntl |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ break;
+ default:
+ ERROR_REPORT1(IXGBE_ERROR_ARGUMENT,
+ "Flow control param set incorrectly\n");
+ return IXGBE_ERR_CONFIG;
+ }
+
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl);
+
+ /* Restart auto-negotiation. */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_ctrl);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ return status;
+ }
+
+ link_ctrl |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, link_ctrl);
+
+ return status;
+}
+
/**
* ixgbe_set_mux - Set mux for port 1 access with CS4227
* @hw: pointer to hardware structure
*
* Acquires the SWFW semaphore and get the shared phy token as needed
*/
-static s32 ixgbe_acquire_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask)
+STATIC s32 ixgbe_acquire_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask)
{
u32 hmask = mask & ~IXGBE_GSSR_TOKEN_SM;
int retries = FW_PHY_TOKEN_RETRIES;
DEBUGFUNC("ixgbe_acquire_swfw_sync_X550a");
while (--retries) {
+ status = IXGBE_SUCCESS;
if (hmask)
status = ixgbe_acquire_swfw_sync_X540(hw, hmask);
if (status)
- break;
+ return status;
if (!(mask & IXGBE_GSSR_TOKEN_SM))
- break;
+ return IXGBE_SUCCESS;
+
status = ixgbe_get_phy_token(hw);
- if (status != IXGBE_ERR_TOKEN_RETRY)
- break;
+ if (status == IXGBE_SUCCESS)
+ return IXGBE_SUCCESS;
+
if (hmask)
ixgbe_release_swfw_sync_X540(hw, hmask);
+ if (status != IXGBE_ERR_TOKEN_RETRY)
+ return status;
msec_delay(FW_PHY_TOKEN_DELAY);
}
*
* Releases the SWFW semaphore and puts the shared phy token as needed
*/
-static void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask)
+STATIC void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask)
{
u32 hmask = mask & ~IXGBE_GSSR_TOKEN_SM;
ixgbe_release_swfw_sync_X540(hw, hmask);
}
+/**
+ * ixgbe_read_phy_reg_x550a - Reads specified PHY register
+ * @hw: pointer to hardware structure
+ * @reg_addr: 32 bit address of PHY register to read
+ * @phy_data: Pointer to read data from PHY register
+ *
+ * Reads a value from a specified PHY register using the SWFW lock and PHY
+ * Token. The PHY Token is needed since the MDIO is shared between to MAC
+ * instances.
+ **/
+s32 ixgbe_read_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
+ u32 device_type, u16 *phy_data)
+{
+ s32 status;
+ u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
+
+ DEBUGFUNC("ixgbe_read_phy_reg_x550a");
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, mask))
+ return IXGBE_ERR_SWFW_SYNC;
+
+ status = hw->phy.ops.read_reg_mdi(hw, reg_addr, device_type, phy_data);
+
+ hw->mac.ops.release_swfw_sync(hw, mask);
+
+ return status;
+}
+
+/**
+ * ixgbe_write_phy_reg_x550a - Writes specified PHY register
+ * @hw: pointer to hardware structure
+ * @reg_addr: 32 bit PHY register to write
+ * @device_type: 5 bit device type
+ * @phy_data: Data to write to the PHY register
+ *
+ * Writes a value to specified PHY register using the SWFW lock and PHY Token.
+ * The PHY Token is needed since the MDIO is shared between to MAC instances.
+ **/
+s32 ixgbe_write_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
+ u32 device_type, u16 phy_data)
+{
+ s32 status;
+ u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
+
+ DEBUGFUNC("ixgbe_write_phy_reg_x550a");
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, mask) == IXGBE_SUCCESS) {
+ status = ixgbe_write_phy_reg_mdi(hw, reg_addr, device_type,
+ phy_data);
+ hw->mac.ops.release_swfw_sync(hw, mask);
+ } else {
+ status = IXGBE_ERR_SWFW_SYNC;
+ }
+
+ return status;
+}
+
/**
* ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt
* @hw: pointer to hardware structure
Code Review / deb_dpdk.git / blobdiff