--- /dev/null
+/*-
+ * BSD LICENSE
+ *
+ * Copyright(c) 2010-2015 Intel Corporation. All rights reserved.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Intel Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include "base/ixgbe_type.h"
+#include "base/ixgbe_82599.h"
+#include "base/ixgbe_api.h"
+#include "base/ixgbe_common.h"
+#include "base/ixgbe_phy.h"
+#include "ixgbe_bypass_defines.h"
+#include "ixgbe_bypass.h"
+
+/**
+ * ixgbe_set_fiber_fixed_speed - Set module link speed for fixed fiber
+ * @hw: pointer to hardware structure
+ * @speed: link speed to set
+ *
+ * We set the module speed differently for fixed fiber. For other
+ * multi-speed devices we don't have an error value so here if we
+ * detect an error we just log it and exit.
+ */
+static void
+ixgbe_set_fiber_fixed_speed(struct ixgbe_hw *hw, ixgbe_link_speed speed)
+{
+ s32 status;
+ u8 rs, eeprom_data;
+
+ switch (speed) {
+ case IXGBE_LINK_SPEED_10GB_FULL:
+ /* one bit mask same as setting on */
+ rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
+ break;
+ case IXGBE_LINK_SPEED_1GB_FULL:
+ rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
+ break;
+ default:
+ PMD_DRV_LOG(ERR, "Invalid fixed module speed");
+ return;
+ }
+
+ /* Set RS0 */
+ status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ &eeprom_data);
+ if (status) {
+ PMD_DRV_LOG(ERR, "Failed to read Rx Rate Select RS0");
+ goto out;
+ }
+
+ eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs;
+
+ status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ eeprom_data);
+ if (status) {
+ PMD_DRV_LOG(ERR, "Failed to write Rx Rate Select RS0");
+ goto out;
+ }
+
+ /* Set RS1 */
+ status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ &eeprom_data);
+ if (status) {
+ PMD_DRV_LOG(ERR, "Failed to read Rx Rate Select RS1");
+ goto out;
+ }
+
+ eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) & rs;
+
+ status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
+ IXGBE_I2C_EEPROM_DEV_ADDR2,
+ eeprom_data);
+ if (status) {
+ PMD_DRV_LOG(ERR, "Failed to write Rx Rate Select RS1");
+ goto out;
+ }
+out:
+ return;
+}
+
+/**
+ * ixgbe_setup_mac_link_multispeed_fixed_fiber - Set MAC link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Set the link speed in the AUTOC register and restarts link.
+ **/
+static s32
+ixgbe_setup_mac_link_multispeed_fixed_fiber(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ s32 status = IXGBE_SUCCESS;
+ ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+ ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+ u32 speedcnt = 0;
+ u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP);
+ u32 i = 0;
+ bool link_up = false;
+ bool negotiation;
+
+ PMD_INIT_FUNC_TRACE();
+
+ /* Mask off requested but non-supported speeds */
+ status = ixgbe_get_link_capabilities(hw, &link_speed, &negotiation);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ speed &= link_speed;
+
+ /*
+ * Try each speed one by one, highest priority first. We do this in
+ * software because 10gb fiber doesn't support speed autonegotiation.
+ */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
+ speedcnt++;
+ highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = ixgbe_check_link(hw, &link_speed, &link_up, false);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ if ((link_speed == IXGBE_LINK_SPEED_10GB_FULL) && link_up)
+ goto out;
+ /* Set the module link speed */
+ ixgbe_set_fiber_fixed_speed(hw, IXGBE_LINK_SPEED_10GB_FULL);
+
+ /* Set the module link speed */
+ esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5);
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg);
+ IXGBE_WRITE_FLUSH(hw);
+
+ /* Allow module to change analog characteristics (1G->10G) */
+ msec_delay(40);
+
+ status = ixgbe_setup_mac_link_82599(hw,
+ IXGBE_LINK_SPEED_10GB_FULL,
+ autoneg_wait_to_complete);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Flap the tx laser if it has not already been done */
+ ixgbe_flap_tx_laser(hw);
+
+ /*
+ * Wait for the controller to acquire link. Per IEEE 802.3ap,
+ * Section 73.10.2, we may have to wait up to 500ms if KR is
+ * attempted. 82599 uses the same timing for 10g SFI.
+ */
+ for (i = 0; i < 5; i++) {
+ /* Wait for the link partner to also set speed */
+ msec_delay(100);
+
+ /* If we have link, just jump out */
+ status = ixgbe_check_link(hw, &link_speed,
+ &link_up, false);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+ }
+
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
+ speedcnt++;
+ if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If we already have link at this speed, just jump out */
+ status = ixgbe_check_link(hw, &link_speed, &link_up, false);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ if ((link_speed == IXGBE_LINK_SPEED_1GB_FULL) && link_up)
+ goto out;
+
+ /* Set the module link speed */
+ ixgbe_set_fiber_fixed_speed(hw, IXGBE_LINK_SPEED_1GB_FULL);
+
+ /* Allow module to change analog characteristics (10G->1G) */
+ msec_delay(40);
+
+ status = ixgbe_setup_mac_link_82599(hw,
+ IXGBE_LINK_SPEED_1GB_FULL,
+ autoneg_wait_to_complete);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Flap the tx laser if it has not already been done */
+ ixgbe_flap_tx_laser(hw);
+
+ /* Wait for the link partner to also set speed */
+ msec_delay(100);
+
+ /* If we have link, just jump out */
+ status = ixgbe_check_link(hw, &link_speed, &link_up, false);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ if (link_up)
+ goto out;
+ }
+
+ /*
+ * We didn't get link. Configure back to the highest speed we tried,
+ * (if there was more than one). We call ourselves back with just the
+ * single highest speed that the user requested.
+ */
+ if (speedcnt > 1)
+ status = ixgbe_setup_mac_link_multispeed_fixed_fiber(hw,
+ highest_link_speed, autoneg_wait_to_complete);
+
+out:
+ /* Set autoneg_advertised value based on input link speed */
+ hw->phy.autoneg_advertised = 0;
+
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
+
+ if (speed & IXGBE_LINK_SPEED_1GB_FULL)
+ hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
+
+ return status;
+}
+
+static enum ixgbe_media_type
+ixgbe_bypass_get_media_type(struct ixgbe_hw *hw)
+{
+ enum ixgbe_media_type media_type;
+
+ PMD_INIT_FUNC_TRACE();
+
+ if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) {
+ media_type = ixgbe_media_type_fiber;
+ } else {
+ media_type = ixgbe_get_media_type_82599(hw);
+ }
+ return media_type;
+}
+
+/*
+ * Wrapper around shared code (base driver) to support BYPASS nic.
+ */
+s32
+ixgbe_bypass_init_shared_code(struct ixgbe_hw *hw)
+{
+ s32 ret_val;
+
+ if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) {
+ hw->mac.type = ixgbe_mac_82599EB;
+ }
+
+ ret_val = ixgbe_init_shared_code(hw);
+ if (hw->device_id == IXGBE_DEV_ID_82599_BYPASS) {
+ hw->mac.ops.get_media_type = &ixgbe_bypass_get_media_type;
+ ixgbe_init_mac_link_ops_82599(hw);
+ }
+
+ return ret_val;
+}
+
+s32
+ixgbe_bypass_init_hw(struct ixgbe_hw *hw)
+{
+ int rc;
+
+ if ((rc = ixgbe_init_hw(hw)) == 0 &&
+ hw->device_id == IXGBE_DEV_ID_82599_BYPASS) {
+
+ hw->mac.ops.setup_link =
+ &ixgbe_setup_mac_link_multispeed_fixed_fiber;
+
+ hw->mac.ops.get_media_type = &ixgbe_bypass_get_media_type;
+
+ hw->mac.ops.disable_tx_laser = NULL;
+ hw->mac.ops.enable_tx_laser = NULL;
+ hw->mac.ops.flap_tx_laser = NULL;
+ }
+
+ return rc;
+}
Code Review / deb_dpdk.git / blobdiff