void ecore_resc_setup(struct ecore_dev *p_dev);
struct ecore_hw_init_params {
- /* tunnelling parameters */
- struct ecore_tunn_start_params *p_tunn;
+ /* Tunnelling parameters */
+ struct ecore_tunnel_info *p_tunn;
+
bool b_hw_start;
- /* interrupt mode [msix, inta, etc.] to use */
+
+ /* Interrupt mode [msix, inta, etc.] to use */
enum ecore_int_mode int_mode;
-/* npar tx switching to be used for vports configured for tx-switching */
+ /* NPAR tx switching to be used for vports configured for tx-switching
+ */
bool allow_npar_tx_switch;
- /* binary fw data pointer in binary fw file */
+
+ /* Binary fw data pointer in binary fw file */
const u8 *bin_fw_data;
- /* the OS Epoch time in seconds */
- u32 epoch;
+
+ /* Indicates whether the driver is running over a crash kernel.
+ * As part of the load request, this will be used for providing the
+ * driver role to the MFW.
+ * In case of a crash kernel over PDA - this should be set to false.
+ */
+ bool is_crash_kernel;
+
+ /* The timeout value that the MFW should use when locking the engine for
+ * the driver load process.
+ * A value of '0' means the default value, and '255' means no timeout.
+ */
+ u8 mfw_timeout_val;
+#define ECORE_LOAD_REQ_LOCK_TO_DEFAULT 0
+#define ECORE_LOAD_REQ_LOCK_TO_NONE 255
+
+ /* Avoid engine reset when first PF loads on it */
+ bool avoid_eng_reset;
};
/**
*/
void ecore_hw_start_fastpath(struct ecore_hwfn *p_hwfn);
-/**
- * @brief ecore_hw_reset -
- *
- * @param p_dev
- *
- * @return enum _ecore_status_t
- */
-enum _ecore_status_t ecore_hw_reset(struct ecore_dev *p_dev);
+enum ecore_hw_prepare_result {
+ ECORE_HW_PREPARE_SUCCESS,
+
+ /* FAILED results indicate probe has failed & cleaned up */
+ ECORE_HW_PREPARE_FAILED_ENG2,
+ ECORE_HW_PREPARE_FAILED_ME,
+ ECORE_HW_PREPARE_FAILED_MEM,
+ ECORE_HW_PREPARE_FAILED_DEV,
+ ECORE_HW_PREPARE_FAILED_NVM,
+
+ /* BAD results indicate probe is passed even though some wrongness
+ * has occurred; Trying to actually use [I.e., hw_init()] might have
+ * dire reprecautions.
+ */
+ ECORE_HW_PREPARE_BAD_IOV,
+ ECORE_HW_PREPARE_BAD_MCP,
+ ECORE_HW_PREPARE_BAD_IGU,
+};
struct ecore_hw_prepare_params {
- /* personality to initialize */
+ /* Personality to initialize */
int personality;
- /* force the driver's default resource allocation */
+
+ /* Force the driver's default resource allocation */
bool drv_resc_alloc;
- /* check the reg_fifo after any register access */
+
+ /* Check the reg_fifo after any register access */
bool chk_reg_fifo;
+
+ /* Request the MFW to initiate PF FLR */
+ bool initiate_pf_flr;
+
+ /* The OS Epoch time in seconds */
+ u32 epoch;
+
+ /* Allow prepare to pass even if some initializations are failing.
+ * If set, the `p_prepare_res' field would be set with the return,
+ * and might allow probe to pass even if there are certain issues.
+ */
+ bool b_relaxed_probe;
+ enum ecore_hw_prepare_result p_relaxed_res;
};
/**
enum ecore_chain_cnt_type cnt_type,
u32 num_elems,
osal_size_t elem_size,
- struct ecore_chain *p_chain);
+ struct ecore_chain *p_chain,
+ struct ecore_chain_ext_pbl *ext_pbl);
/**
* @brief ecore_chain_free - Free chain DMA memory
struct ecore_ptt *p_ptt,
u16 id,
bool is_vf);
-
/**
- * @brief ecore_set_rxq_coalesce - Configure coalesce parameters for an Rx queue
- * The fact that we can configure coalescing to up to 511, but on varying
- * accuracy [the bigger the value the less accurate] up to a mistake of 3usec
- * for the highest values.
- *
- * @param p_hwfn
- * @param p_ptt
- * @param coalesce - Coalesce value in micro seconds.
- * @param qid - Queue index.
- * @param qid - SB Id
- *
- * @return enum _ecore_status_t
- */
-enum _ecore_status_t ecore_set_rxq_coalesce(struct ecore_hwfn *p_hwfn,
- struct ecore_ptt *p_ptt,
- u16 coalesce, u8 qid, u16 sb_id);
-
-/**
- * @brief ecore_set_txq_coalesce - Configure coalesce parameters for a Tx queue
- * While the API allows setting coalescing per-qid, all tx queues sharing a
- * SB should be in same range [i.e., either 0-0x7f, 0x80-0xff or 0x100-0x1ff]
+ * @brief ecore_set_queue_coalesce - Configure coalesce parameters for Rx and
+ * Tx queue. The fact that we can configure coalescing to up to 511, but on
+ * varying accuracy [the bigger the value the less accurate] up to a mistake
+ * of 3usec for the highest values.
+ * While the API allows setting coalescing per-qid, all queues sharing a SB
+ * should be in same range [i.e., either 0-0x7f, 0x80-0xff or 0x100-0x1ff]
* otherwise configuration would break.
*
* @param p_hwfn
- * @param p_ptt
- * @param coalesce - Coalesce value in micro seconds.
- * @param qid - Queue index.
- * @param qid - SB Id
+ * @param rx_coal - Rx Coalesce value in micro seconds.
+ * @param tx_coal - TX Coalesce value in micro seconds.
+ * @param p_handle
*
* @return enum _ecore_status_t
- */
-enum _ecore_status_t ecore_set_txq_coalesce(struct ecore_hwfn *p_hwfn,
- struct ecore_ptt *p_ptt,
- u16 coalesce, u8 qid, u16 sb_id);
+ **/
+enum _ecore_status_t
+ecore_set_queue_coalesce(struct ecore_hwfn *p_hwfn, u16 rx_coal,
+ u16 tx_coal, void *p_handle);
#endif
Code Review / deb_dpdk.git / blobdiff