New upstream version 18.11-rc1

[deb_dpdk.git] / drivers / net / qede / base / ecore_l2_api.h

diff --git a/drivers/net/qede/base/ecore_l2_api.h b/drivers/net/qede/base/ecore_l2_api.h
index 575b9e3..004fb61 100644 (file)
--- a/drivers/net/qede/base/ecore_l2_api.h
+++ b/drivers/net/qede/base/ecore_l2_api.h
@@ -137,6 +137,16 @@ struct ecore_filter_accept_flags {
 #define ECORE_ACCEPT_MCAST_MATCHED     0x08
 #define ECORE_ACCEPT_MCAST_UNMATCHED   0x10
 #define ECORE_ACCEPT_BCAST             0x20
+#define ECORE_ACCEPT_ANY_VNI           0x40
+};
+
+enum ecore_filter_config_mode {
+       ECORE_FILTER_CONFIG_MODE_DISABLE,
+       ECORE_FILTER_CONFIG_MODE_5_TUPLE,
+       ECORE_FILTER_CONFIG_MODE_L4_PORT,
+       ECORE_FILTER_CONFIG_MODE_IP_DEST,
+       ECORE_FILTER_CONFIG_MODE_TUNN_TYPE,
+       ECORE_FILTER_CONFIG_MODE_IP_SRC,
 };
 
 struct ecore_arfs_config_params {
@@ -144,7 +154,7 @@ struct ecore_arfs_config_params {
        bool udp;
        bool ipv4;
        bool ipv6;
-       bool arfs_enable;       /* Enable or disable arfs mode */
+       enum ecore_filter_config_mode mode;
 };
 
 /* Add / remove / move / remove-all unicast MAC-VLAN filters.
@@ -337,7 +347,10 @@ struct ecore_sp_vport_update_params {
        /* MTU change - notice this requires the vport to be disabled.
         * If non-zero, value would be used.
         */
-       u16 mtu;
+       u16                     mtu;
+       u8                      update_ctl_frame_check;
+       u8                      mac_chk_en;
+       u8                      ethtype_chk_en;
 };
 
 /**
@@ -460,4 +473,28 @@ ecore_configure_rfs_ntuple_filter(struct ecore_hwfn *p_hwfn,
                                  dma_addr_t p_addr, u16 length,
                                  u16 qid, u8 vport_id,
                                  bool b_is_add);
+
+/**
+ * @brief - ecore_update_eth_rss_ind_table_entry
+ *
+ * This function being used to update RSS indirection table entry to FW RAM
+ * instead of using the SP vport update ramrod with rss params.
+ *
+ * Notice:
+ * This function supports only one outstanding command per engine. Ecore
+ * clients which use this function should call ecore_mcp_ind_table_lock() prior
+ * to it and ecore_mcp_ind_table_unlock() after it.
+ *
+ * @params p_hwfn
+ * @params vport_id
+ * @params ind_table_index
+ * @params ind_table_value
+ *
+ * @return enum _ecore_status_t
+ */
+enum _ecore_status_t
+ecore_update_eth_rss_ind_table_entry(struct ecore_hwfn *p_hwfn,
+                                    u8 vport_id,
+                                    u8 ind_table_index,
+                                    u16 ind_table_value);
 #endif