/* Hey Emacs use -*- mode: C -*- */ /* * Copyright (c) 2015-2016 Cisco and/or its affiliates. * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at: * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. */ option version = "3.0.0"; import "vnet/ip/ip_types.api"; /** \brief IPsec: Add/delete Security Policy Database @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param is_add - add SPD if non-zero, else delete @param spd_id - SPD instance id (control plane allocated) */ autoreply define ipsec_spd_add_del { u32 client_index; u32 context; u8 is_add; u32 spd_id; }; /** \brief IPsec: Add/delete SPD from interface @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param is_add - add security mode if non-zero, else delete @param sw_if_index - index of the interface @param spd_id - SPD instance id to use for lookups */ autoreply define ipsec_interface_add_del_spd { u32 client_index; u32 context; u8 is_add; u32 sw_if_index; u32 spd_id; }; enum ipsec_spd_action { /* bypass - no IPsec processing */ IPSEC_API_SPD_ACTION_BYPASS = 0, /* discard - discard packet with ICMP processing */ IPSEC_API_SPD_ACTION_DISCARD, /* resolve - send request to control plane for SA resolving */ IPSEC_API_SPD_ACTION_RESOLVE, /* protect - apply IPsec policy using following parameters */ IPSEC_API_SPD_ACTION_PROTECT, }; /** \brief IPsec: Security Policy Database entry See RFC 4301, 4.4.1.1 on how to match packet to selectors @param spd_id - SPD instance id (control plane allocated) @param priority - priority of SPD entry (non-unique value). Used to order SPD matching - higher priorities match before lower @param is_outbound - entry applies to outbound traffic if non-zero, otherwise applies to inbound traffic @param remote_address_start - start of remote address range to match @param remote_address_stop - end of remote address range to match @param local_address_start - start of local address range to match @param local_address_stop - end of local address range to match @param protocol - protocol type to match [0 means any] otherwise IANA value @param remote_port_start - start of remote port range to match ... @param remote_port_stop - end of remote port range to match [0 to 65535 means ANY, 65535 to 0 means OPAQUE] @param local_port_start - start of local port range to match ... @param local_port_stop - end of remote port range to match [0 to 65535 means ANY, 65535 to 0 means OPAQUE] @param policy - action to perform on match @param sa_id - SAD instance id (control plane allocated) */ typedef ipsec_spd_entry { u32 spd_id; i32 priority; u8 is_outbound; u32 sa_id; vl_api_ipsec_spd_action_t policy; u8 protocol; // Selector vl_api_address_t remote_address_start; vl_api_address_t remote_address_stop; vl_api_address_t local_address_start; vl_api_address_t local_address_stop; u16 remote_port_start; u16 remote_port_stop; u16 local_port_start; u16 local_port_stop; }; /** \brief IPsec: Add/delete Security Policy Database entry @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param is_add - add SPD if non-zero, else delete @param entry - Description of the entry to add/dell */ define ipsec_spd_entry_add_del { u32 client_index; u32 context; u8 is_add; vl_api_ipsec_spd_entry_t entry; }; /** \brief IPsec: Reply Add/delete Security Policy Database entry @param context - sender context, to match reply w/ request @param retval - success/fail rutrun code @param stat_index - An index for the policy in the stats segment @ /net/ipec/policy */ define ipsec_spd_entry_add_del_reply { u32 context; i32 retval; u32 stat_index; }; /** \brief Dump IPsec all SPD IDs @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request */ define ipsec_spds_dump { u32 client_index; u32 context; }; /** \brief Dump IPsec all SPD IDs response @param client_index - opaque cookie to identify the sender @param spd_id - SPD instance id (control plane allocated) @param npolicies - number of policies in SPD */ define ipsec_spds_details { u32 context; u32 spd_id; u32 npolicies; }; /** \brief Dump ipsec policy database data @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param spd_id - SPD instance id @param sa_id - SA id, optional, set to ~0 to see all policies in SPD */ define ipsec_spd_dump { u32 client_index; u32 context; u32 spd_id; u32 sa_id; }; /** \brief IPsec policy database response @param context - sender context which was passed in the request €param entry - The SPD entry. @param bytes - byte count of packets matching this policy @param packets - count of packets matching this policy */ define ipsec_spd_details { u32 context; vl_api_ipsec_spd_entry_t entry; }; /* * @brief Support cryptographic algorithms */ enum ipsec_crypto_alg { IPSEC_API_CRYPTO_ALG_NONE = 0, IPSEC_API_CRYPTO_ALG_AES_CBC_128, IPSEC_API_CRYPTO_ALG_AES_CBC_192, IPSEC_API_CRYPTO_ALG_AES_CBC_256, IPSEC_API_CRYPTO_ALG_AES_CTR_128, IPSEC_API_CRYPTO_ALG_AES_CTR_192, IPSEC_API_CRYPTO_ALG_AES_CTR_256, IPSEC_API_CRYPTO_ALG_AES_GCM_128, IPSEC_API_CRYPTO_ALG_AES_GCM_192, IPSEC_API_CRYPTO_ALG_AES_GCM_256, IPSEC_API_CRYPTO_ALG_DES_CBC, IPSEC_API_CRYPTO_ALG_3DES_CBC, }; /* * @brief Supported Integrity Algorithms */ enum ipsec_integ_alg { IPSEC_API_INTEG_ALG_NONE = 0, /* RFC2403 */ IPSEC_API_INTEG_ALG_MD5_96, /* RFC2404 */ IPSEC_API_INTEG_ALG_SHA1_96, /* draft-ietf-ipsec-ciph-sha-256-00 */ IPSEC_API_INTEG_ALG_SHA_256_96, /* RFC4868 */ IPSEC_API_INTEG_ALG_SHA_256_128, /* RFC4868 */ IPSEC_API_INTEG_ALG_SHA_384_192, /* RFC4868 */ IPSEC_API_INTEG_ALG_SHA_512_256, }; enum ipsec_sad_flags { IPSEC_API_SAD_FLAG_NONE = 0, /* Enable extended sequence numbers */ IPSEC_API_SAD_FLAG_USE_ESN = 0x01, /* Enable Anti-replay */ IPSEC_API_SAD_FLAG_USE_ANTI_REPLAY = 0x02, /* IPsec tunnel mode if non-zero, else transport mode */ IPSEC_API_SAD_FLAG_IS_TUNNEL = 0x04, /* IPsec tunnel mode is IPv6 if non-zero, * else IPv4 tunnel only valid if is_tunnel is non-zero */ IPSEC_API_SAD_FLAG_IS_TUNNEL_V6 = 0x08, /* enable UDP encapsulation for NAT traversal */ IPSEC_API_SAD_FLAG_UDP_ENCAP = 0x10, }; enum ipsec_proto { IPSEC_API_PROTO_ESP, IPSEC_API_PROTO_AH, }; typedef key { /* the length of the key */ u8 length; /* The data for the key */ u8 data[128]; }; /** \brief IPsec: Security Association Database entry @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param is_add - add SAD entry if non-zero, else delete @param sad_id - sad id @param spi - security parameter index @param protocol - 0 = AH, 1 = ESP @param crypto_algorithm - a supported crypto algorithm @param crypto_key - crypto keying material @param integrity_algorithm - one of the supported algorithms @param integrity_key - integrity keying material @param tunnel_src_address - IPsec tunnel source address IPv6 if is_tunnel_ipv6 is non-zero, else IPv4. Only valid if is_tunnel is non-zero @param tunnel_dst_address - IPsec tunnel destination address IPv6 if is_tunnel_ipv6 is non-zero, else IPv4. Only valid if is_tunnel is non-zero @param tx_table_id - the FIB id used for encapsulated packets @param salt - for use with counter mode ciphers */ typedef ipsec_sad_entry { u32 sad_id; u32 spi; vl_api_ipsec_proto_t protocol; vl_api_ipsec_crypto_alg_t crypto_algorithm; vl_api_key_t crypto_key; vl_api_ipsec_integ_alg_t integrity_algorithm; vl_api_key_t integrity_key; vl_api_ipsec_sad_flags_t flags; vl_api_address_t tunnel_src; vl_api_address_t tunnel_dst; u32 tx_table_id; u32 salt; }; /** \brief IPsec: Add/delete Security Association Database entry @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param entry - Entry to add or delete */ define ipsec_sad_entry_add_del { u32 client_index; u32 context; u8 is_add; vl_api_ipsec_sad_entry_t entry; }; define ipsec_sad_entry_add_del_reply { u32 context; i32 retval; u32 stat_index; }; /** \brief IPsec: Get SPD interfaces @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param spd_index - SPD index @param spd_index_valid - if 1 spd_index is used to filter spd_index's, if 0 no filtering is done */ define ipsec_spd_interface_dump { u32 client_index; u32 context; u32 spd_index; u8 spd_index_valid; }; /** \brief IPsec: SPD interface response @param context - sender context which was passed in the request @param spd_index - SPD index @param sw_if_index - index of the interface */ define ipsec_spd_interface_details { u32 context; u32 spd_index; u32 sw_if_index; }; /** \brief Add or delete IPsec tunnel interface @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param is_add - add IPsec tunnel interface if nonzero, else delete @param is_ip6 - tunnel v6 or v4 @param esn - enable extended sequence numbers if nonzero, else disable @param anti_replay - enable anti replay check if nonzero, else disable @param local_ip - local IP address @param remote_ip - IP address of remote IPsec peer @param local_spi - SPI of outbound IPsec SA @param remote_spi - SPI of inbound IPsec SA @param crypto_alg - encryption algorithm ID @param local_crypto_key_len - length of local crypto key in bytes @param local_crypto_key - crypto key for outbound IPsec SA @param remote_crypto_key_len - length of remote crypto key in bytes @param remote_crypto_key - crypto key for inbound IPsec SA @param integ_alg - integrity algorithm ID @param local_integ_key_len - length of local integrity key in bytes @param local_integ_key - integrity key for outbound IPsec SA @param remote_integ_key_len - length of remote integrity key in bytes @param remote_integ_key - integrity key for inbound IPsec SA @param renumber - intf display name uses a specified instance if != 0 @param show_instance - instance to display for intf if renumber is set @param udp_encap - enable UDP encapsulation for NAT traversal @param tx_table_id - the FIB id used after packet encap @param salt - for use with counter mode ciphers */ define ipsec_tunnel_if_add_del { u32 client_index; u32 context; u8 is_add; u8 esn; u8 anti_replay; vl_api_address_t local_ip; vl_api_address_t remote_ip; u32 local_spi; u32 remote_spi; u8 crypto_alg; u8 local_crypto_key_len; u8 local_crypto_key[128]; u8 remote_crypto_key_len; u8 remote_crypto_key[128]; u8 integ_alg; u8 local_integ_key_len; u8 local_integ_key[128]; u8 remote_integ_key_len; u8 remote_integ_key[128]; u8 renumber; u32 show_instance; u8 udp_encap; u32 tx_table_id; u32 salt; }; /** \brief Add/delete IPsec tunnel interface response @param context - sender context, to match reply w/ request @param retval - return status @param sw_if_index - sw_if_index of new interface (for successful add) */ define ipsec_tunnel_if_add_del_reply { u32 context; i32 retval; u32 sw_if_index; }; /** \brief Dump IPsec security association @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param sa_id - optional ID of an SA to dump, if ~0 dump all SAs in SAD */ define ipsec_sa_dump { u32 client_index; u32 context; u32 sa_id; }; /** \brief IPsec security association database response @param context - sender context which was passed in the request @param sa_id - SA ID, policy-based SAs >=0, tunnel interface SAs = 0 @param sw_if_index - sw_if_index of tunnel interface, policy-based SAs = ~0 @param spi - security parameter index @param protocol - IPsec protocol (value from ipsec_protocol_t) @param crypto_alg - crypto algorithm (value from ipsec_crypto_alg_t) @param crypto_key_len - length of crypto_key in bytes @param crypto_key - crypto keying material @param integ_alg - integrity algorithm (value from ipsec_integ_alg_t) @param integ_key_len - length of integ_key in bytes @param integ_key - integrity keying material @param use_esn - using extended sequence numbers when non-zero @param use_anti_replay - using anti-replay window when non-zero @param is_tunnel - IPsec tunnel mode when non-zero, else transport mode @param is_tunnel_ipv6 - If using tunnel mode, endpoints are IPv6 @param tunnel_src_addr - Tunnel source address if using tunnel mode @param tunnel_dst_addr - Tunnel destination address is using tunnel mode @param salt - 4 byte salt @param seq - current sequence number for outbound @param seq_hi - high 32 bits of ESN for outbound @param last_seq - highest sequence number received inbound @param last_seq_hi - high 32 bits of highest ESN received inbound @param replay_window - bit map of seq nums received relative to last_seq if using anti-replay @param total_data_size - total bytes sent or received @param udp_encap - 1 if UDP encap enabled, 0 otherwise */ define ipsec_sa_details { u32 context; vl_api_ipsec_sad_entry_t entry; u32 sw_if_index; u32 salt; u64 seq_outbound; u64 last_seq_inbound; u64 replay_window; u64 total_data_size; }; /** \brief Set new SA on IPsec interface @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param sw_if_index - index of tunnel interface @param sa_id - ID of SA to use @param is_outbound - 1 if outbound (local) SA, 0 if inbound (remote) */ autoreply define ipsec_tunnel_if_set_sa { u32 client_index; u32 context; u32 sw_if_index; u32 sa_id; u8 is_outbound; }; /** \brief Dump IPsec backends @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request */ define ipsec_backend_dump { u32 client_index; u32 context; }; /** \brief IPsec backend details @param name - name of the backend @param protocol - IPsec protocol (value from ipsec_protocol_t) @param index - backend index @param active - set to 1 if the backend is active, otherwise 0 */ define ipsec_backend_details { u32 context; u8 name[128]; vl_api_ipsec_proto_t protocol; u8 index; u8 active; }; /** \brief Select IPsec backend @param client_index - opaque cookie to identify the sender @param context - sender context, to match reply w/ request @param protocol - IPsec protocol (value from ipsec_protocol_t) @param index - backend index */ autoreply define ipsec_select_backend { u32 client_index; u32 context; vl_api_ipsec_proto_t protocol; u8 index; }; /* * Local Variables: * eval: (c-set-style "gnu") * End: */