Typos. A bunch of typos I've been collecting.

[vpp.git] / test / test_mpls.py

diff --git a/test/test_mpls.py b/test/test_mpls.py
index 09e4752..8d5d5ab 100644 (file)
--- a/test/test_mpls.py
+++ b/test/test_mpls.py
@@ -452,7 +452,7 @@ class TestMPLS(VppTestCase):
         self.verify_capture_ip4(self.pg0, rx, tx)
 
         #
-        # disposed packets have an invalid IPv4 checkusm
+        # disposed packets have an invalid IPv4 checksum
         #
         tx = self.create_stream_labelled_ip4(self.pg0, [VppMplsLabel(33)],
                                              dst_ip=self.pg0.remote_ip4,
@@ -1281,7 +1281,7 @@ class TestMPLS(VppTestCase):
         self.send_and_assert_no_replies(self.pg0, tx, "RPF-ID drop none")
 
         #
-        # set the RPF-ID of the enrtry to match the input packet's
+        # set the RPF-ID of the entry to match the input packet's
         #
         route_232_1_1_1.update_rpf_id(55)
 
@@ -1291,7 +1291,7 @@ class TestMPLS(VppTestCase):
         self.verify_capture_ip4(self.pg1, rx, tx)
 
         #
-        # disposed packets have an invalid IPv4 checkusm
+        # disposed packets have an invalid IPv4 checksum
         #
         tx = self.create_stream_labelled_ip4(self.pg0, [VppMplsLabel(34)],
                                              dst_ip="232.1.1.1", n=65,
@@ -1351,7 +1351,7 @@ class TestMPLS(VppTestCase):
         self.send_and_assert_no_replies(self.pg0, tx, "RPF Miss")
 
         #
-        # set the RPF-ID of the enrtry to match the input packet's
+        # set the RPF-ID of the entry to match the input packet's
         #
         route_ff.update_rpf_id(55)
 
@@ -1371,7 +1371,7 @@ class TestMPLS(VppTestCase):
         self.verify_capture_ip6_icmp(self.pg0, rx, tx)
 
         #
-        # set the RPF-ID of the enrtry to not match the input packet's
+        # set the RPF-ID of the entry to not match the input packet's
         #
         route_ff.update_rpf_id(56)
         tx = self.create_stream_labelled_ip6(self.pg0,
@@ -1392,7 +1392,7 @@ class TestMPLSDisabled(VppTestCase):
         self.tbl = VppMplsTable(self, 0)
         self.tbl.add_vpp_config()
 
-        # PG0 is MPLS enalbed
+        # PG0 is MPLS enabled
         self.pg0.admin_up()
         self.pg0.config_ip4()
         self.pg0.resolve_arp()
@@ -1573,7 +1573,7 @@ class TestMPLSPIC(VppTestCase):
         rx0 = self.pg0._get_capture(1)
         rx1 = self.pg1._get_capture(1)
 
-        # not testig the LB hashing algorithm so we're not concerned
+        # not testing the LB hashing algorithm so we're not concerned
         # with the split ratio, just as long as neither is 0
         self.assertNotEqual(0, len(rx0))
         self.assertNotEqual(0, len(rx1))
@@ -1581,7 +1581,7 @@ class TestMPLSPIC(VppTestCase):
         #
         # use a test CLI command to stop the FIB walk process, this
         # will prevent the FIB converging the VPN routes and thus allow
-        # us to probe the interim (psot-fail, pre-converge) state
+        # us to probe the interim (post-fail, pre-converge) state
         #
         self.vapi.ppcli("test fib-walk-process disable")
 
@@ -1681,7 +1681,7 @@ class TestMPLSPIC(VppTestCase):
         #
         # use a test CLI command to stop the FIB walk process, this
         # will prevent the FIB converging the VPN routes and thus allow
-        # us to probe the interim (psot-fail, pre-converge) state
+        # us to probe the interim (post-fail, pre-converge) state
         #
         self.vapi.ppcli("test fib-walk-process disable")
 
@@ -1781,7 +1781,7 @@ class TestMPLSPIC(VppTestCase):
         #
         # use a test CLI command to stop the FIB walk process, this
         # will prevent the FIB converging the VPN routes and thus allow
-        # us to probe the interim (psot-fail, pre-converge) state
+        # us to probe the interim (post-fail, pre-converge) state
         #
         self.vapi.ppcli("test fib-walk-process disable")
 
@@ -1937,7 +1937,7 @@ class TestMPLSL2(VppTestCase):
         self.assertEqual(rx0[0][Ether].src, payload[Ether].src)
 
         #
-        # Inject a packet from the custoer/L2 side
+        # Inject a packet from the customer/L2 side
         #
         tx1 = pcore[MPLS].payload * 65
         rx1 = self.send_and_expect(self.pg1, tx1, self.pg0)