-------------------------
CSIT Honeycomb functional tests are executed on virtualized topologies created
-using Virtual Internet Routing Lab (VIRL) simulation platform contributed by
-Cisco. VIRL runs on physical baremetal servers hosted by LF FD.io project. All
-tests are executed in two node logical test topology - Traffic Generator (TG)
-node and Systems Under Test (SUT1) node connected in a loop. Logical test
-topology is shown in the figure below.
-
-::
+using :abbr:`VIRL (Virtual Internet Routing Lab)` simulation platform
+contributed by Cisco. VIRL runs on physical baremetal servers hosted by LF FD.io
+project. All tests are executed in two node logical test topology - Traffic
+Generator (TG) node and Systems Under Test (SUT1) node connected in a loop.
+Logical test topology is shown in the figure below.::
+------------------------+
| |
- **Basic interface management** - CRUD for interface state,
- ipv4/ipv6 address, ipv4 neighbor, MTU value.
- - Test case count: 7
+ - Test case count: 14
- **L2BD** - CRUD for L2 Bridge-Domain, interface assignment.
- Create up to two bridge domains with all implemented functions turned on.
- (flooding, unknown-unicast flooding, forwarding, learning, arp-termination)
- Toggle interface state separately for super-interface and sub-interface.
- Configure IP address and bridge domain assignment on sub-interface.
- Configure VLAN tag rewrite on sub-interface.
- - Test case count: 17
+ - Test case count: 24
- **ACL** - CRD for low-level classifiers: table and session management,
- interface assignment.
- Configure up to 2 classify tables.
- Test case count: 9
- **PBB** - CRD for provider backbone bridge sub-interface.
- Configure, modify and remove a PBB sub-interface over a physical interface.
- - Test case count: 9
+ - Test case count: 8
- **NSH_SFC** - CRD for NSH maps and entries, using NSH_SFC plugin.
- Configure up to 2 NSH entries.
- Configure up to 2 NSH maps.
- Configure and delete Lisp mapping as local and remote.
- Configure and delete Lisp adjacency mapping
- Configure and delete Lisp map resolver, proxy ITR.
- - Test case count: 11
+ - Test case count: 18
+- **LISP GPE** - CRUD for LISP GPE mappings.
+ - Toggle Lisp GPE feature status.
+ - Configure Lisp GPE mappings.
+ - Traffic test verifying encapsulation.
+ - Test case count: 12
- **NAT** - CRD for NAT entries, interface assignment.
- Configure and delete up to two NAT entries.
- Assign NAT entries to a physical interface.
- Configure SPAN port mirroring on a physical interface, mirroring
- up to 2 interfaces.
- Remove SPAN configuration from interfaces.
- - Test case count: 3
+ - Test case count: 14
- **ACL-PLUGIN** - CRD for high-level classifier
- MAC + IP address classification.
- IPv4, IPv6 address classification.
- Configure blackhole route.
- IPv4 and IPv6 variants.
- Test case count: 6
+- **Policer** - CRD for traffic policing feature.
+ - Configure Policing rules.
+ - Assign to interface.
+ - Test case count: 6
+- **Border Gateway Protocol** - CRUD and functional tests for BGP.
+ - Configure peers and routes
+ - Check interactions with another BGP peer.
+ - Test case count: 9
- **Honeycomb Infractructure** - configuration persistence,
- Netconf notifications for interface events,
- Netconf negative tests aimed at specific issues
+ - Netconf/Restconf northbound over IPv6
-Total 158 Honeycomb tests in the CSIT |release|.
+Total 217 Honeycomb functional tests in the CSIT |release|.
Operational data in Honeycomb should mirror configuration data at all times.
Because of this, test cases follow this general pattern:
#. modify configuration of the feature using restconf.
#. verify changes to operational data using restconf.
#. verify changes using VPP API dump, OR
-#. send a packet to VPP node and observe behaviour to verify configuration
+#. send a packet to VPP node and observe behaviour to verify configuration.
Test cases involving network interfaces utilize the first two interfaces on
the DUT node.
#. **Physical port to physical port - a.k.a. NIC-to-NIC, Phy-to-Phy, P2P**
- - *eth2p-ethip4-ip4base-func.robot* => 2 ports of Ethernet, IPv4 baseline
- routed forwarding, functional tests.
+ - *eth2p-ethip4-ip4base-func.robot* => 2 ports of Ethernet, IPv4 baseline
+ routed forwarding, functional tests.
#. **Physical port to VM (or VM chain) to physical port - a.k.a. NIC2VM2NIC,
P2V2P, NIC2VMchain2NIC, P2V2V2P**
- - *eth2p-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-func.robot* => 2 ports of
- Ethernet, IPv4 VXLAN Ethernet, L2 bridge-domain switching to/from two vhost
- interfaces and one VM, functional tests.
+ - *eth2p-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-func.robot* => 2 ports of
+ Ethernet, IPv4 VXLAN Ethernet, L2 bridge-domain switching to/from two vhost
+ interfaces and one VM, functional tests.