Add Honeycomb bridge domain management tests

[csit.git] / tests / suites / honeycomb / interface_management.robot

diff --git a/tests/suites/honeycomb/interface_management.robot b/tests/suites/honeycomb/interface_management.robot
deleted file mode 100644 (file)
index 3408b52..0000000
--- a/tests/suites/honeycomb/interface_management.robot
+++ /dev/null
@@ -1,101 +0,0 @@
-# Copyright (c) 2016 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Variables ***
-# Node and interface to run tests on.
-| ${node}= | ${nodes['DUT1']}
-| ${interface}= | ${node['interfaces'].values()[0]['name']}
-# Configuration which will be set and verified during tests.
-| @{ipv4_address}= | 192.168.0.2 | 255.255.255.0
-| @{ipv4_neighbor}= | 192.168.0.3 | 08:00:27:c0:5d:37
-| &{ipv4_settings}= | enabled=${True} | forwarding=${True} | mtu=9000
-| @{ipv6_address}= | 10::10 | 64
-| @{ipv6_neighbor}= | 10::11 | 08:00:27:c0:5d:37
-| &{ipv6_settings}= | enabled=${True} | forwarding=${True} | mtu=9000
-| ... | dup-addr-detect-transmits=5
-| &{ethernet}= | mtu=9000
-| &{routing}= | vrf-id=27
-| &{vxlan_settings}= | src=10.0.1.20 | dst=10.0.3.20 | vni=1000
-| ... | encap-vrf-id=1000
-
-*** Settings ***
-| Resource | resources/libraries/robot/default.robot
-| Resource | resources/libraries/robot/honeycomb/honeycomb.robot
-| Resource | resources/libraries/robot/honeycomb/interfaces.robot
-| Suite Setup | Run keywords | Setup all DUTs before test | AND
-| ... | Setup Honeycomb service on DUTs | ${node}
-| Suite Teardown | Stop Honeycomb service on DUTs | ${node}
-| Documentation | *Honeycomb interface management test suite.*
-| ...
-| ... | Test suite uses the first interface of the first DUT node.
-
-*** Test Cases ***
-| Honeycomb configures and reads interface state
-| | [Documentation] | Check if Honeycomb API can modify the admin state of\
-| | ... | VPP interfaces.
-| | [Tags] | honeycomb_sanity
-| | Given Interface state is | ${node} | ${interface} | down
-| | When Honeycomb sets interface state | ${node} | ${interface} | up
-| | Then Interface state from Honeycomb should be
-| | ... | ${node} | ${interface} | up
-| | And Interface state from VAT should be | ${node} | ${interface} | up
-| | When Honeycomb sets interface state | ${node} | ${interface} | down
-| | Then Interface state from Honeycomb should be
-| | ... | ${node} | ${interface} | down
-| | And Interface state from VAT should be | ${node} | ${interface} | down
-
-| Honeycomb modifies interface configuration - ipv4
-| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv4.
-| | [Tags] | honeycomb_sanity
-| | When Honeycomb sets interface ipv4 configuration
-| | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor}
-| | ... | ${ipv4_settings}
-| | Then IPv4 config from Honeycomb should be
-| | ... | ${node} | ${interface} | @{ipv4_address} | @{ipv4_neighbor}
-| | ... | ${ipv4_settings}
-| | And IPv4 config from VAT should be
-| | ... | ${node} | ${interface} | @{ipv4_address}
-
-| Honeycomb modifies interface configuration - ipv6
-| | [Documentation] | Check if Honeycomb API can configure interfaces for ipv6.
-| | [Tags] | honeycomb_sanity
-| | When Honeycomb sets interface ipv6 configuration
-| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
-| | ... | ${ipv6_settings}
-| | Then IPv6 config from Honeycomb should be
-| | ... | ${node} | ${interface} | @{ipv6_address} | @{ipv6_neighbor}
-| | ... | ${ipv6_settings}
-| | And IPv6 config from VAT should be
-| | ... | ${node} | ${interface} | @{ipv6_address}
-
-| Honeycomb modifies interface configuration - ethernet,routing
-| | [Documentation] | Check if Honeycomb API can configure interface ethernet\
-| | ... | and routing settings.
-| | [Tags] | honeycomb_sanity
-| | When Honeycomb sets interface ethernet and routing configuration
-| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
-| | Then Interface ethernet and routing configuration from Honeycomb should be
-| | ... | ${node} | ${interface} | ${ethernet} | ${routing}
-| | And Interface ethernet and routing configuration from VAT should be
-| | ... | ${node} | ${interface} | ${ethernet['mtu']} | ${routing['vrf-id']}
-
-| Honeycomb modifies interface configuration - VxLAN
-| | [Documentation] | Check if Honeycomb API can configure interface VxLAN \
-| | ... | settings.
-| | [Tags] | honeycomb_sanity
-| | When Honeycomb sets interface VxLAN configuration
-| | ... | ${node} | ${interface} | &{vxlan_settings}
-| | Then VxLAN configuration from Honeycomb should be
-| | ... | ${node} | ${interface} | &{vxlan_settings}
-| | And VxLAN configuration from VAT should be
-| | ... | ${node} | ${interface} | &{vxlan_settings}