1 # Copyright (c) 2020 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
6 # http://www.apache.org/licenses/LICENSE-2.0
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
15 | Resource | resources/libraries/robot/shared/default.robot
17 | Variables | resources/test_data/lisp/lisp.py
19 | Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY
20 | ... | NIC_Virtual | IP4FWD | LISPGPE_IP6o4 | DRV_VFIO_PCI
21 | ... | RXQ_SIZE_0 | TXQ_SIZE_0
22 | ... | ethip4lispgpe-ip6base
24 | Suite Setup | Setup suite single link | scapy
25 | Test Setup | Setup test
26 | Test Teardown | Tear down test | packet_trace
28 | Test Template | Local Template
30 | Documentation | *ip4-lispgpe-ip6 encapsulation test cases*
32 | ... | *[Top] Network Topologies:* TG(if1)-DUT1-TG(if2) 2-node\
33 | ... | circular topology with single links between nodes.
34 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4-LISPGPE-IPv6-ICMPv6\
35 | ... | on DUT1-TG(if2),Eth-IPv6-ICMPv6 on TG-DUTn for IPv6\
36 | ... | routing over LISPoIPv4 tunnel.
37 | ... | *[Cfg] DUT configuration:* DUT1 and TG(if2) are configured\
38 | ... | with IPv6 routing and static routes. LISPoIPv4 tunnel is\
39 | ... | configured between DUT1 and TG(if2).
40 | ... | *[Ver] TG verification:* Test ICMPv6 Echo Request packets\
41 | ... | are sent in if1 by TG on links to DUT1; on receive\
42 | ... | TG verifies packets for correctness and their IPv6 src-addr,\
43 | ... | dst-addr and MAC addresses.
44 | ... | *[Ref] Applicable standard specifications:* RFC6830.
47 | @{plugins_to_enable}= | dpdk_plugin.so
48 | ${crypto_type}= | ${None}
49 | ${nic_name}= | virtual
50 | ${nic_driver}= | vfio-pci
51 | ${nic_rxq_size}= | 0
52 | ${nic_txq_size}= | 0
53 | ${overhead}= | ${54}
60 | | ... | [Cfg] On DUT1 configure LISPGPE\
62 | | ... | *Arguments:*
63 | | ... | - frame_size - Framesize in Bytes in integer. Type: integer
64 | | ... | - phy_cores - Number of physical cores. Type: integer
65 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
67 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
69 | | Set Test Variable | \${frame_size}
71 | | Given Set Max Rate And Jumbo
72 | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
73 | | And Pre-initialize layer driver | ${nic_driver}
74 | | And Apply startup configuration on all VPP DUTs | with_trace=${True}
75 | | When Initialize layer driver | ${nic_driver}
76 | | And Initialize layer interface
77 | | And Configure topology for IPv6 LISPoIP4 testing
78 | | And Vpp All RA Suppress Link Layer | ${nodes}
79 | | And Configure LISP in 2-node circular topology
80 | | ... | ${dut1} | ${dut1_if2} | ${NONE}
81 | | ... | ${duts_locator_set} | ${dut1_ip6o4_eid}
82 | | ... | ${dut1_ip6o4_static_adjacency} | ${is_gpe}
83 | | Then Send packet and verify LISPoTunnel encap
84 | | ... | ${tg} | ${tg_if1_ip6} | ${dst_ip6}
85 | | ... | ${tg_if1} | ${tg_if1_mac} | ${dut1_if1_mac}
86 | | ... | ${tg_if2} | ${dut1_if2_mac} | ${tg_if2_mac}
87 | | ... | ${src_rloc4} | ${dst_rloc4} | ${ot_mode}
90 | tc01-62B-ethip4lispgpe-ip6base-dev
92 | | frame_size=${62} | phy_cores=${0}