Support suite tags in autogen
[csit.git] / tests / vpp / device / vm_vhost / l2xc / eth2p-ethipv4-l2xcbase-eth-2vhost-1vm-dev.robot
1 # Copyright (c) 2019 Cisco and/or its affiliates.
2 # Licensed under the Apache License, Version 2.0 (the "License");
3 # you may not use this file except in compliance with the License.
4 # You may obtain a copy of the License at:
5 #
6 #     http://www.apache.org/licenses/LICENSE-2.0
7 #
8 # Unless required by applicable law or agreed to in writing, software
9 # distributed under the License is distributed on an "AS IS" BASIS,
10 # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
11 # See the License for the specific language governing permissions and
12 # limitations under the License.
13
14 *** Settings ***
15 | Resource | resources/libraries/robot/shared/default.robot
16 |
17 | Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV | SCAPY
18 | ... | NIC_Virtual | ETH | L2XCFWD | BASE | VHOST | 1VM | DRV_VFIO_PCI
19 | ... | ethipv4-l2xcbase-eth-2vhost-1vm
20 |
21 | Suite Setup | Setup suite single link | scapy
22 | Test Setup | Setup test
23 | Test Teardown | Tear down test | packet_trace | vhost
24 |
25 | Test Template | Local Template
26 |
27 | Documentation | *L2 cross-connect test cases with vhost user interface*
28 |
29 | ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology with \
30 | ... | VM and single links between nodes.
31 | ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for L2 switching of IPv4.
32 | ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect \
33 | ... | (L2XC) switching. Qemu Guest is connected to VPP via vhost-user \
34 | ... | interfaces. Guest is configured with VPP l2 cross-connect \
35 | ... | interconnecting vhost-user interfaces.
36 | ... | *[Ver] TG verification:* Test IPv4 packets with IP protocol=61 are \
37 | ... | sent in both directions by TG on links to DUT1 via VM; on receive TG \
38 | ... | verifies packets for correctness and their IPv4 src-addr, dst-addr \
39 | ... | and MAC addresses.
40 | ... | *[Ref] Applicable standard specifications:* RFC792
41
42 *** Variables ***
43 | @{plugins_to_enable}= | dpdk_plugin.so
44 | ${crypto_type}= | ${None}
45 | ${nic_name}= | virtual
46 | ${nic_driver}= | vfio-pci
47 | ${overhead}= | ${0}
48 | ${nf_chains}= | ${1}
49 | ${nf_nodes}= | ${1}
50 | ${nf_dtc} | ${1}
51 | ${nf_dtcr} | ${1}
52
53 *** Keywords ***
54 | Local Template
55 | | [Documentation]
56 | | ... | [Top] TG=DUT=VM. [Enc] Eth-IPv4. [Cfg] On DUT configure \
57 | | ... | two L2 cross-connects (L2XC), each with one untagged interface \
58 | | ... | to TG and untagged i/f to local VM over vhost-user. [Ver] Make \
59 | | ... | TG send IPv4 packets in both directions between two of its \
60 | | ... | i/fs to be switched by DUT to and from VM; verify all packets \
61 | | ... | are received. [Ref]
62 | |
63 | | ... | *Arguments:*
64 | | ... | - frame_size - Framesize in Bytes in integer. Type: integer
65 | | ... | - phy_cores - Number of physical cores. Type: integer
66 | | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
67 | |
68 | | [Arguments] | ${frame_size} | ${phy_cores} | ${rxq}=${None}
69 | |
70 | | Set Test Variable | \${frame_size}
71 | |
72 | | Given Set Max Rate And Jumbo
73 | | And Add worker threads to all DUTs | ${phy_cores} | ${rxq}
74 | | And Pre-initialize layer driver | ${nic_driver}
75 | | And Apply startup configuration on all VPP DUTs | with_trace=${True}
76 | | When Initialize layer driver | ${nic_driver}
77 | | And Initialize layer interface
78 | | And Initialize L2 xconnect with Vhost-User | nf_nodes=${nf_nodes}
79 | | And Configure chains of NFs connected via vhost-user
80 | | ... | nf_chains=${nf_chains} | nf_nodes=${nf_nodes} | vnf=vpp_chain_l2xc
81 | | ... | pinning=${False}
82 | | Then Send IPv4 bidirectionally and verify received packets | ${tg}
83 | | ... | ${tg_if1} | ${tg_if2}
84
85 *** Test Cases ***
86 | tc01-64B-ethipv4-l2xcbase-eth-2vhost-1vm-dev
87 | | [Tags] | 64B
88 | | frame_size=${64} | phy_cores=${0}