| | ... | using PLRsearch algorithm.
| | ... | Display results as formatted test message.
| | ... | Fail if computed lower bound is 110% of the minimal rate or less.
| | ... | using PLRsearch algorithm.
| | ... | Display results as formatted test message.
| | ... | Fail if computed lower bound is 110% of the minimal rate or less.
-| | ... | Input rates are understood as uni-directional,
-| | ... | reported result contains aggregate rates.
+| | ... | Input rates are unidirectional, in transaction per second.
+| | ... | Reported result may contain aggregate pps rates, depending on test.
| | ... | Currently, the min_rate value is hardcoded to match test teardowns.
| | ... | Call \${resetter} (if defined) to reset DUT state before each trial.
| |
| | ... | Currently, the min_rate value is hardcoded to match test teardowns.
| | ... | Call \${resetter} (if defined) to reset DUT state before each trial.
| |
| | ... | using an optimized search algorithm.
| | ... | Display findings as a formatted test message.
| | ... | Fail if a resulting lower bound has too high loss fraction.
| | ... | using an optimized search algorithm.
| | ... | Display findings as a formatted test message.
| | ... | Fail if a resulting lower bound has too high loss fraction.
-| | ... | Input rates are understood as uni-directional,
-| | ... | reported result contains aggregate rates.
+| | ... | Input rates are unidirectional, in transaction per second.
+| | ... | Reported result may contain aggregate pps rates, depending on test.
| | ... | Additional latency measurements are performed for smaller loads,
| | ... | even if latency stream is disabled in search. Their results
| | ... | are also displayed.
| | ... | Additional latency measurements are performed for smaller loads,
| | ... | even if latency stream is disabled in search. Their results
| | ... | are also displayed.
| | ... | Type: float
| | ... | - resetter - Callable to reset DUT state before each trial.
| | ... | - transaction_scale - Number of ASTF transaction (zero if unlimited).
| | ... | Type: float
| | ... | - resetter - Callable to reset DUT state before each trial.
| | ... | - transaction_scale - Number of ASTF transaction (zero if unlimited).
-| | ... | aggregate throughput using MLRsearch algorithm.
-| | ... | Input rates are understood as uni-directional.
+| | ... | throughput using MLRsearch algorithm.
+| | ... | Input and output rates are understood as uni-directional, in tps.
| | ... | Currently, the min_rate value is hardcoded to match test teardowns.
| | ... | Call \${resetter} (if defined) to reset DUT state before each trial.
| |
| | ... | Currently, the min_rate value is hardcoded to match test teardowns.
| | ... | Call \${resetter} (if defined) to reset DUT state before each trial.
| |
| | ... | Type: float
| | ... | - resetter - Callable to reset DUT state before each trial.
| | ... | - transaction_scale - Number of ASTF transaction (zero if unlimited).
| | ... | Type: float
| | ... | - resetter - Callable to reset DUT state before each trial.
| | ... | - transaction_scale - Number of ASTF transaction (zero if unlimited).
| | [Documentation]
| | ... | Send traffic at specified rate, single trial.
| | ... | Extract latency information and append it to text message.
| | [Documentation]
| | ... | Send traffic at specified rate, single trial.
| | ... | Extract latency information and append it to text message.
| | ... | If the given rate is too low, a safe value is used instead.
| | ... | Call \${resetter} (if defined) to reset DUT state before each trial.
| |
| | ... | *Arguments:*
| | ... | - message_prefix - Preface to test message addition. Type: string
| | ... | If the given rate is too low, a safe value is used instead.
| | ... | Call \${resetter} (if defined) to reset DUT state before each trial.
| |
| | ... | *Arguments:*
| | ... | - message_prefix - Preface to test message addition. Type: string
| | ... | Type: float
| | ... | - transaction_type - String identifier to determine how to count
| | ... | transactions. Default is "packet".
| | ... | Type: float
| | ... | - transaction_type - String identifier to determine how to count
| | ... | transactions. Default is "packet".