VPP_Device - add baseline tests - part I

[csit.git] / tests / vpp / device / l2xc / eth2p-ethicmp-l2xcbase-device.robot

diff --git a/tests/vpp/device/l2xc/eth2p-ethicmp-l2xcbase-device.robot b/tests/vpp/device/l2xc/eth2p-ethicmp-l2xcbase-device.robot
deleted file mode 100644 (file)
index b18ce7b..0000000
--- a/tests/vpp/device/l2xc/eth2p-ethicmp-l2xcbase-device.robot
+++ /dev/null
@@ -1,75 +0,0 @@
-# Copyright (c) 2018 Cisco and/or its affiliates.
-# Licensed under the Apache License, Version 2.0 (the "License");
-# you may not use this file except in compliance with the License.
-# You may obtain a copy of the License at:
-#
-#     http://www.apache.org/licenses/LICENSE-2.0
-#
-# Unless required by applicable law or agreed to in writing, software
-# distributed under the License is distributed on an "AS IS" BASIS,
-# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-# See the License for the specific language governing permissions and
-# limitations under the License.
-
-*** Settings ***
-| Resource | resources/libraries/robot/shared/default.robot
-| Resource | resources/libraries/robot/l2/l2_xconnect.robot
-| Resource | resources/libraries/robot/l2/l2_traffic.robot
-| Resource | resources/libraries/robot/shared/testing_path.robot
-| ...
-| Force Tags | 2_NODE_SINGLE_LINK_TOPO | DEVICETEST | HW_ENV | DCR_ENV
-| ... | L2XCFWD | ICMP
-| ...
-| Test Setup | Set up VPP device test
-| ...
-| Test Teardown | Tear down VPP device test
-| ...
-| Documentation | *L2 cross-connect test cases*
-| ...
-| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
-| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-ICMPv4 for L2 switching of\
-| ... | IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all\
-| ... | links.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 cross-connect\
-| ... | switching.
-| ... | *[Ver] TG verification:* Test ICMPv4 (or ICMPv6) Echo Request packets\
-| ... | are sent in both directions by TG on links to DUT1; on receive TG\
-| ... | verifies packets for correctness and their IPv4 (IPv6) src-addr,\
-| ... | dst-addr and MAC addresses.
-| ... | *[Ref] Applicable standard specifications: rfc792*
-
-*** Test Cases ***
-| tc01-eth2p-ethicmpv4-l2xcbase-device
-| | [Documentation]
-| | ... | [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv4.
-| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC), with both interfaces\
-| | ... | to TG.
-| | ... | [Ver] Make TG send ICMPv4 Echo Req in both directions between two of\
-| | ... | its interfaces to be switched by DUT1; verify all packets are
-| | ... | received.
-| | ...
-| | Given Configure path in 2-node circular topology
-| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']}
-| | And Set Interfaces In 2-node Circular Topology Up
-| | And Configure L2XC | ${dut_node} | ${dut_to_tg_if1} | ${dut_to_tg_if2}
-| | When All Vpp Interfaces Ready Wait | ${nodes}
-| | Then Send ICMPv4 bidirectionally and verify received packets
-| | ... | ${tg_node} | ${tg_to_dut_if1} | ${tg_to_dut_if2}
-
-| tc02-eth2p-ethicmpv6-l2xcbase-device
-| | [Documentation]
-| | ... | [Top] TG-DUT1-TG. [Enc] Eth-IPv4-ICMPv6.
-| | ... | [Cfg] On DUT1 configure L2 cross-connect (L2XC), with both interfaces\
-| | ... | to TG.
-| | ... | [Ver] Make TG send ICMPv4 Echo Req in both directions between two of\
-| | ... | its interfaces to be switched by DUT1; verify all packets are
-| | ... | received.
-| | ...
-| | Given Configure path in 2-node circular topology
-| | ... | ${nodes['TG']} | ${nodes['DUT1']} | ${nodes['TG']}
-| | And Set Interfaces In 2-node Circular Topology Up
-| | And Configure L2XC | ${dut_node} | ${dut_to_tg_if1} | ${dut_to_tg_if2}
-| | When All Vpp Interfaces Ready Wait | ${nodes}
-| | Then Send ICMPv6 bidirectionally and verify received packets
-| | ... | ${tg_node} | ${tg_to_dut_if1} | ${tg_to_dut_if2}