CSIT-675: SRv6 performance tests
[csit.git] / tests / vpp / perf / srv6 / 10ge2p1x520-ethip6srhip6-ip6base-srv6enc2sids-ndrpdrdisc.robot
diff --git a/tests/vpp/perf/srv6/10ge2p1x520-ethip6srhip6-ip6base-srv6enc2sids-ndrpdrdisc.robot b/tests/vpp/perf/srv6/10ge2p1x520-ethip6srhip6-ip6base-srv6enc2sids-ndrpdrdisc.robot
new file mode 100644 (file)
index 0000000..30d84d2
--- /dev/null
@@ -0,0 +1,253 @@
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+#     http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 3_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDRDISC
+| ... | NIC_Intel-X520-DA2 | ETH | IP6FWD | FEATURE | SRv6
+| ...
+| Suite Setup | Set up 3-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X520-DA2
+| Suite Teardown | Tear down 3-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance test with SRv6 with encapsulation
+| ... | ${min_rate}pps | ${framesize} | ${traffic_profile}
+| ...
+| Documentation | *Packet throughput Segment routing over IPv6 dataplane with\
+| ... | two SIDs (SRH inserted) test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv6-SRH-IPv6 on DUT1-DUT2, Eth-IPv6\
+| ... | on TG-DUTn for IPv6 routing over SRv6.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv6\
+| ... | routing and static route, SR policy and steering policy for one\
+| ... | direction and two SR behaviours (functions) - End and End.DX6 - for\
+| ... | other direction. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic\
+| ... | by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using either binary search or linear search\
+| ... | algorithms with configured starting rate and final step that determines\
+| ... | throughput measurement resolution. Test packets are generated by TG on\
+| ... | links to DUTs. TG traffic profile contains two L3 flow-groups\
+| ... | (flow-group per direction, 253 flows per flow-group) with\
+| ... | all packets containing Ethernet header,IPv6 header with static payload.\
+| ... | MAC addresses are matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* SRv6 Network Programming -\
+| ... | draft 3.
+| ...
+
+*** Variables ***
+# X520-DA2 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# SIDs
+| ${dut1_sid1}= | 2002:1::
+| ${dut1_sid2_1}= | 2003:2::
+| ${dut1_sid2_2}= | 2003:3::
+| ${dut1_bsid}= | 2002:1::1
+| ${dut2_sid1_1}= | 2002:2::
+| ${dut2_sid1_2}= | 2002:3::
+| ${dut2_sid2}= | 2003:1::
+| ${dut2_bsid}= | 2002:2::1
+| ${sid_prefix}= | ${64}
+# IP settings
+| ${tg_if1_ip6_subnet}= | 2001:1::
+| ${tg_if2_ip6_subnet}= | 2001:2::
+| ${dst_addr_nr}= | ${1}
+| ${dut1_if1_ip6}= | 2001:1::1
+| ${dut1_if2_ip6}= | 2001:3::1
+| ${dut2_if1_ip6}= | 2001:3::2
+| ${dut2_if2_ip6}= | 2001:2::1
+| ${prefix}= | ${64}
+# outer IPv6 header + SRH with 2 SIDs: 40+40B
+| ${srv6_overhead_2sids}= | ${80}
+# Traffic profile:
+| ${traffic_profile} | trex-sl-3n-ethip6-ip6src253
+
+*** Keywords ***
+| Discover NDR or PDR for IPv6 routing over SRv6
+| | [Arguments] | ${wt} | ${rxq} | ${framesize} | ${min_rate} | ${search_type}
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate}
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | ${max_rate}= | Calculate pps | ${s_limit}
+| | ... | ${get_framesize} + ${srv6_overhead_2sids}
+| | ${binary_min}= | Set Variable | ${min_rate}
+| | ${binary_max}= | Set Variable | ${max_rate}
+| | ${threshold}= | Set Variable | ${min_rate}
+| | Given Add '${wt}' worker threads and '${rxq}' rxqueues in 3-node single-link circular topology
+| | And Add PCI devices to DUTs in 3-node single link topology
+| | ${get_framesize}= | Get Frame Size | ${framesize}
+| | And Run Keyword If | ${get_framesize} < ${1522} | Add no multi seg to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv6 forwarding over SRv6 with encapsulation with '2' x SID 'with' decapsulation in 3-node circular topology
+| | Then Run Keyword If | '${search_type}' == 'NDR'
+| | ... | Find NDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ELSE IF | '${search_type}' == 'PDR'
+| | ... | Find PDR using binary search and pps
+| | ... | ${framesize} | ${binary_min} | ${binary_max} | ${traffic_profile}
+| | ... | ${min_rate} | ${max_rate} | ${threshold}
+| | ... | ${perf_pdr_loss_acceptance} | ${perf_pdr_loss_acceptance_type}
+
+*** Test Cases ***
+| tc01-78B-1t1c-ethip6srhip6-ip6base-srv6enc2sids-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 78B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=1 | rxq=1 | framesize=${78} | min_rate=${100000} | search_type=NDR
+
+| tc02-78B-1t1c-ethip6srhip6-ip6base-srv6enc2sids-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 78B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=1 | rxq=1 | framesize=${78} | min_rate=${100000} | search_type=PDR
+
+| tc03-78B-2t2c-ethip6srhip6-ip6base-srv6enc2sids-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 78B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=2 | rxq=1 | framesize=${78} | min_rate=${100000} | search_type=NDR
+
+| tc04-78B-2t2c-ethip6srhip6-ip6base-srv6enc2sids-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 78B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=2 | rxq=1 | framesize=${78} | min_rate=${100000} | search_type=PDR
+
+| tc05-78B-4t4c-ethip6srhip6-ip6base-srv6enc2sids-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 78 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 78B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=4 | rxq=2 | framesize=${78} | min_rate=${100000} | search_type=NDR
+
+| tc06-78B-4t4c-ethip6srhip6-ip6base-srv6enc2sids-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 78 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 78B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=4 | rxq=2 | framesize=${78} | min_rate=${100000} | search_type=PDR
+
+| tc07-1518B-1t1c-ethip6srhip6-ip6base-srv6enc2sids-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR
+
+| tc08-1518B-1t1c-ethip6srhip6-ip6base-srv6enc2sids-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 1 thread, 1 phy core, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1518B | 1T1C | STHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=1 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR
+
+| tc09-1518B-2t2c-ethip6srhip6-ip6base-srv6enc2sids-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=NDR
+
+| tc10-1518B-2t2c-ethip6srhip6-ip6base-srv6enc2sids-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 2 threads, 2 phy cores, 1 receive queue per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1518B | 2T2C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=2 | rxq=1 | framesize=${1518} | min_rate=${100000} | search_type=PDR
+
+| tc11-1518B-4t4c-ethip6srhip6-ip6base-srv6enc2sids-ndrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD | NDRDISC
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=NDR
+
+| tc12-1518B-4t4c-ethip6srhip6-ip6base-srv6enc2sids-pdrdisc
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv6 over SRv6 routing config with\
+| | ... | 4 threads, 4 phy cores, 2 receive queues per NIC port.
+| | ... | [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE\
+| | ... | linerate, step 100kpps, LT=0.5%.
+| | ...
+| | [Tags] | 1518B | 4T4C | MTHREAD | PDRDISC | SKIP_PATCH
+| | ...
+| | [Template] | Discover NDR or PDR for IPv6 routing over SRv6
+| | wt=4 | rxq=2 | framesize=${1518} | min_rate=${100000} | search_type=PDR