| | Vpp Route Add | ${dut1} | ${laddr_ip4} | 8 | ${tg_if1_ip4} | ${dut1_if1}
| | Vpp Route Add | ${dut2} | ${raddr_ip4} | 8 | ${tg_if2_ip4} | ${dut2_if2}
-| Initialize IPv4 forwarding in 2-node circular topology
+| Initialize IPv4 forwarding in circular topology
| | [Documentation]
-| | ... | Set UP state on VPP interfaces in path on nodes in 2-node circular
-| | ... | topology. Get the interface MAC addresses and setup ARP on all VPP
-| | ... | interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG links and
-| | ... | /30 prefix on DUT1 link.
+| | ... | Set UP state on VPP interfaces in path on nodes in 2-node / 3-node
+| | ... | circular topology. Get the interface MAC addresses and setup ARP on
+| | ... | all VPP interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG
+| | ... | links. In case of 3-node topology setup IPv4 adresses with /30 prefix
+| | ... | on DUT1-DUT2 link and set routing on both DUT nodes with prefix /24
+| | ... | and next hop of neighbour DUT interface IPv4 address.
| | ...
-| | Set interfaces in path up
-| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
-| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
-| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
-| | Add arp on dut | ${dut1} | ${dut1_if2} | 20.20.20.2 | ${tg1_if2_mac}
-| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1}
-| | ... | 10.10.10.1 | 24
-| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
-| | ... | 20.20.20.1 | 24
-
-| Initialize IPv4 forwarding in 3-node circular topology
-| | [Documentation]
-| | ... | Set UP state on VPP interfaces in path on nodes in 3-node circular
-| | ... | topology. Get the interface MAC addresses and setup ARP on all VPP
-| | ... | interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG links and
-| | ... | /30 prefix on DUT1-DUT2 link. Set routing on both DUT nodes with
-| | ... | prefix /24 and next hop of neighbour DUT interface IPv4 address.
+| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
+| | ... | Variable Should Exist | ${dut2}
| | ...
| | Set interfaces in path up
+| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
-| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
-| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
+| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
+| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
+| | ...
| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.2 | ${tg1_if1_mac}
-| | Add arp on dut | ${dut1} | ${dut1_if2} | 1.1.1.2 | ${dut2_if1_mac}
-| | Add arp on dut | ${dut2} | ${dut2_if1} | 1.1.1.1 | ${dut1_if2_mac}
-| | Add arp on dut | ${dut2} | ${dut2_if2} | 20.20.20.2 | ${tg1_if2_mac}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 1.1.1.2 | ${dut2_if1_mac}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 1.1.1.1 | ${dut1_if2_mac}
+| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2}
+| | ... | ELSE | Set Variable | ${dut1}
+| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2_if2}
+| | ... | ELSE | Set Variable | ${dut1_if2}
+| | Add arp on dut | ${dut} | ${dut_if2} | 20.20.20.2 | ${tg1_if2_mac}
+| | ...
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1}
| | ... | 10.10.10.1 | 24
-| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2}
| | ... | 1.1.1.1 | 30
-| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1}
| | ... | 1.1.1.2 | 30
-| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2}
+| | Configure IP addresses on interfaces | ${dut} | ${dut_if2}
| | ... | 20.20.20.1 | 24
-| | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 1.1.1.2 | ${dut1_if2}
-| | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut2_if1}
+| | ...
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 1.1.1.2 | ${dut1_if2}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut2_if1}
| Initialize IPv4 forwarding with scaling in 3-node circular topology
| | [Documentation]
| | | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | ${ip_net_vif2}.2
| | | ... | ${dut2-vhost-${number}-if2} | vrf=${fib_table_2}
-| Initialize IPv4 policer 2r3c-${t} in 3-node circular topology
+| Initialize IPv4 policer 2r3c-${t} in circular topology
| | [Documentation]
| | ... | Setup of 2r3c color-aware or color-blind policer with dst ip match
-| | ... | on all DUT nodes in 3-node circular topology. Policer is applied on
-| | ... | links TG - DUT1 and DUT2 - TG.
+| | ... | on all DUT nodes in 2-node / 3-node circular topology. Policer is
+| | ... | applied on links TG - DUTx.
| | ...
| | ${dscp}= | DSCP AF22
| | Policer Set Name | policer1
| | Policer Classify Set Interface | ${dut1_if1}
| | Policer Classify Set Match IP | 20.20.20.2 | ${False}
| | Policer Set Configuration
-| | Policer Set Node | ${dut2}
-| | Policer Classify Set Interface | ${dut2_if2}
+| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
+| | ... | Variable Should Exist | ${dut2}
+| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2}
+| | ... | ELSE | Set Variable | ${dut1}
+| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2_if2}
+| | ... | ELSE | Set Variable | ${dut1_if2}
+| | Run Keyword Unless | '${dut2_status}' == 'PASS'
+| | ... | Policer Set Name | policer2
+| | Policer Set Node | ${dut}
+| | Policer Classify Set Interface | ${dut_if2}
| | Policer Classify Set Match IP | 10.10.10.2 | ${False}
| | Policer Set Configuration
| | Configure L2XC | ${dut2} | ${dut2_if1} | ${dut2_if2}
| | Configure IPv4 ACLs | ${dut1} | ${dut1_if1} | ${dut1_if2}
-| Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | [Documentation]
-| | ... | Set UP state on VPP interfaces in path on nodes in 3-node circular
-| | ... | topology. Get the interface MAC addresses and setup ARP on all VPP
-| | ... | interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG links and
-| | ... | /30 prefix on DUT1-DUT2 link. Set routing on both DUT nodes with
-| | ... | prefix /24 and next hops of neighbour DUT interface IPv4 address.
+| | ... | Set UP state on VPP interfaces in path on nodes in 2-node / 3-node
+| | ... | circular topology. Get the interface MAC addresses and setup ARP on
+| | ... | all VPP interfaces. Setup IPv4 addresses with /24 prefix on DUT-TG
+| | ... | links. In case of 3-node topology setup IPv4 adresses with /30 prefix
+| | ... | on DUT1-DUT2 link and set routing on both DUT nodes with prefix /24
+| | ... | and next hop of neighbour DUT interface IPv4 address.
| | ... | Apply required ACL rules to DUT1 interfaces.
| | ...
| | ... | *Arguments:*
| | ... | in 3-node circular topology \|
| | ...
| | ... | _NOTE:_ This KW uses following test case variables:
+| | ... | - ${tg} - TG node.
| | ... | - ${dut1} - DUT1 node.
| | ... | - ${dut2} - DUT2 node.
-| | ... | - ${dut1_if1} - DUT1 interface towards TG.
-| | ... | - ${dut1_if2} - DUT1 interface towards DUT2.
-| | ... | - ${dut2_if1} - DUT2 interface towards DUT1.
-| | ... | - ${dut2_if2} - DUT2 interface towards TG.
+| | ... | - ${tg_if1} - TG interface 1 towards DUT1.
+| | ... | - ${tg_if2} - TG interface 2 towards DUT2 (3-node topo) or DUT1
+| | ... | (2-node topo).
+| | ... | - ${dut1_if1} - DUT1 interface 1 towards TG.
+| | ... | - ${dut1_if2} - DUT1 interface 2 towards DUT2 (3-node topo) or TG
+| | ... | (2-node topo).
+| | ... | - ${dut2_if1} - DUT2 interface 1 towards DUT1.
+| | ... | - ${dut2_if2} - DUT2 interface 2 towards TG.
+| | ...
+| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
+| | ... | Variable Should Exist | ${dut2}
+| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2}
+| | ... | ELSE | Set Variable | ${dut1}
+| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2_if2}
+| | ... | ELSE | Set Variable | ${dut1_if2}
| | ...
| | Set interfaces in path up
+| | ...
| | ${tg1_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg1_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
-| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
-| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
+| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
+| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
+| | ...
| | :FOR | ${number} | IN RANGE | 2 | ${ip_nr}+2
| | | Add arp on dut | ${dut1} | ${dut1_if1} | 10.10.10.${number}
| | | ... | ${tg1_if1_mac}
-| | | Add arp on dut | ${dut2} | ${dut2_if2} | 20.20.20.${number}
+| | | Add arp on dut | ${dut} | ${dut_if2} | 20.20.20.${number}
| | | ... | ${tg1_if2_mac}
-| | Add arp on dut | ${dut1} | ${dut1_if2} | 1.1.1.2 | ${dut2_if1_mac}
-| | Add arp on dut | ${dut2} | ${dut2_if1} | 1.1.1.1 | ${dut1_if2_mac}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 1.1.1.2 | ${dut2_if1_mac}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 1.1.1.1 | ${dut1_if2_mac}
+| | ...
| | Configure IP addresses on interfaces
| | ... | ${dut1} | ${dut1_if1} | 10.10.10.1 | 24
+| | ... | ${dut} | ${dut_if2} | 20.20.20.1 | 24
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Configure IP addresses on interfaces
| | ... | ${dut1} | ${dut1_if2} | 1.1.1.1 | 30
| | ... | ${dut2} | ${dut2_if1} | 1.1.1.2 | 30
-| | ... | ${dut2} | ${dut2_if2} | 20.20.20.1 | 24
-| | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 1.1.1.2 | ${dut1_if2}
-| | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut2_if1}
+| | ...
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut1} | 20.20.20.0 | 24 | 1.1.1.2 | ${dut1_if2}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut2} | 10.10.10.0 | 24 | 1.1.1.1 | ${dut2_if1}
+| | ...
| | Configure IPv4 ACLs | ${dut1} | ${dut1_if1} | ${dut1_if2}
| Configure MACIP ACLs
| | Add arp on dut | ${dut2} | ${dut2_if1} | ${dut1_dut2_ip4_address}
| | ... | ${dut1_if2_mac}
-| Initialize NAT44 in 3-node circular topology
-| | [Documentation] | Initialization of 3-node topology with NAT44 between DUTs:
+| Initialize NAT44 in circular topology
+| | [Documentation] | Initialization of 2-node / 3-node topology with NAT44
+| | ... | between DUTs:
| | ... | - set interfaces up
| | ... | - set IP addresses
| | ... | - set ARP
| | ... | - create routes
| | ... | - set NAT44 - only on DUT1
| | ...
+| | ${dut2_status} | ${value}= | Run Keyword And Ignore Error
+| | ... | Variable Should Exist | ${dut2}
+| | ...
| | Set interfaces in path up
| | ...
| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if1} | 10.0.0.1 | 20
-| | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 11.0.0.1 | 20
-| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 11.0.0.2 | 20
-| | Configure IP addresses on interfaces | ${dut2} | ${dut2_if2} | 12.0.0.1 | 20
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Configure IP addresses on interfaces | ${dut1} | ${dut1_if2} | 11.0.0.1 | 20
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Configure IP addresses on interfaces | ${dut2} | ${dut2_if1} | 11.0.0.2 | 20
+| | ${dut}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2}
+| | ... | ELSE | Set Variable | ${dut1}
+| | ${dut_if2}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Set Variable | ${dut2_if2}
+| | ... | ELSE | Set Variable | ${dut1_if2}
+| | Configure IP addresses on interfaces | ${dut} | ${dut_if2} | 12.0.0.1 | 20
| | ...
| | ${tg_if1_mac}= | Get Interface MAC | ${tg} | ${tg_if1}
| | ${tg_if2_mac}= | Get Interface MAC | ${tg} | ${tg_if2}
-| | ${dut1_if2_mac}= | Get Interface MAC | ${dut1} | ${dut1_if2}
-| | ${dut2_if1_mac}= | Get Interface MAC | ${dut2} | ${dut2_if1}
+| | ${dut1_if2_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Get Interface MAC | ${dut1} | ${dut1_if2}
+| | ${dut2_if1_mac}= | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Get Interface MAC | ${dut2} | ${dut2_if1}
| | ...
| | Add arp on dut | ${dut1} | ${dut1_if1} | 10.0.0.2 | ${tg_if1_mac}
-| | Add arp on dut | ${dut1} | ${dut1_if2} | 11.0.0.2 | ${dut2_if1_mac}
-| | Add arp on dut | ${dut2} | ${dut2_if1} | 11.0.0.1 | ${dut1_if2_mac}
-| | Add arp on dut | ${dut2} | ${dut2_if2} | 12.0.0.2 | ${tg_if2_mac}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Add arp on dut | ${dut1} | ${dut1_if2} | 11.0.0.2 | ${dut2_if1_mac}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Add arp on dut | ${dut2} | ${dut2_if1} | 11.0.0.1 | ${dut1_if2_mac}
+| | Add arp on dut | ${dut} | ${dut_if2} | 12.0.0.2 | ${tg_if2_mac}
| | ...
-| | Vpp Route Add | ${dut1} | 12.0.0.2 | 32 | 11.0.0.2 | ${dut1_if2}
| | Vpp Route Add | ${dut1} | 20.0.0.0 | 18 | 10.0.0.2 | ${dut1_if1}
-| | Vpp Route Add | ${dut2} | 12.0.0.0 | 24 | 12.0.0.2 | ${dut2_if2}
-| | Vpp Route Add | ${dut2} | 200.0.0.0 | 30 | 11.0.0.1 | ${dut2_if1}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut1} | 12.0.0.2 | 32 | 11.0.0.2 | ${dut1_if2}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut2} | 12.0.0.0 | 24 | 12.0.0.2 | ${dut2_if2}
+| | Run Keyword If | '${dut2_status}' == 'PASS'
+| | ... | Vpp Route Add | ${dut2} | 200.0.0.0 | 30 | 11.0.0.1 | ${dut2_if1}
| | ...
| | Configure inside and outside interfaces
| | ... | ${dut1} | ${dut1_if1} | ${dut1_if2}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+"""Stream profile for T-rex traffic generator.
+
+Stream profile:
+ - Two streams sent in directions 0 --> 1 and 1 --> 0 at the same time.
+ - Packet: ETH / IP / UDP
+ - Direction 0 --> 1:
+ - Source IP address range: 10.10.10.2 - 10.10.10.11
+ - Destination IP address range: 20.20.20.2 - 20.20.20.11
+ - Source UDP port range: 1001 - 2000
+ - Destination UDP port range: 2001 - 3000
+ - Direction 1 --> 0:
+ - Source IP address range: 20.20.20.2 - 20.20.20.11
+ - Destination IP address range: 10.10.10.2 - 10.10.10.11
+ - Source UDP port range: 2001 - 3000
+ - Destination UDP port range: 1001 - 2000
+"""
+
+from trex_stl_lib.api import *
+from profile_trex_stateless_base_class import TrafficStreamsBaseClass
+
+
+class TrafficStreams(TrafficStreamsBaseClass):
+ """Stream profile."""
+
+ def __init__(self):
+ """Initialization and setting of streams' parameters."""
+
+ super(TrafficStreamsBaseClass, self).__init__()
+
+ # IPs used in packet headers.
+ self.p1_src_start_ip = '10.10.10.2'
+ self.p1_src_end_ip = '10.10.10.11'
+ self.p1_dst_start_ip = '20.20.20.2'
+ self.p1_dst_end_ip = '20.20.20.11'
+
+ self.p2_src_start_ip = '20.20.20.2'
+ self.p2_src_end_ip = '20.20.20.11'
+ self.p2_dst_start_ip = '10.10.10.2'
+ self.p2_dst_end_ip = '10.10.10.11'
+
+ # UDP ports used in packet headers.
+ self.p1_src_start_udp_port = 1001
+ self.p1_src_end_udp_port = 2000
+ self.p1_dst_start_udp_port = 2001
+ self.p1_dst_end_udp_port = 3000
+
+ self.p2_src_start_udp_port = 2001
+ self.p2_src_end_udp_port = 3000
+ self.p2_dst_start_udp_port = 1001
+ self.p2_dst_end_udp_port = 2000
+
+ def define_packets(self):
+ """Defines the packets to be sent from the traffic generator.
+
+ Packet definition: | ETH | IP | UDP |
+
+ :returns: Packets to be sent from the traffic generator.
+ :rtype: tuple
+ """
+
+ # Direction 0 --> 1
+ base_pkt_a = (Ether() /
+ IP(src=self.p1_src_start_ip,
+ dst=self.p1_dst_start_ip,
+ proto=17) /
+ UDP(sport=self.p1_src_start_udp_port,
+ dport=self.p1_dst_start_udp_port))
+ # Direction 1 --> 0
+ base_pkt_b = (Ether() /
+ IP(src=self.p2_src_start_ip,
+ dst=self.p2_dst_start_ip,
+ proto=17) /
+ UDP(sport=self.p2_src_start_udp_port,
+ dport=self.p2_dst_start_udp_port))
+
+ # Direction 0 --> 1
+ vm1 = STLScVmRaw([
+ STLVmTupleGen(ip_min=self.p1_src_start_ip,
+ ip_max=self.p1_src_end_ip,
+ port_min=self.p1_src_start_udp_port,
+ port_max=self.p1_src_end_udp_port,
+ name="tuple1_src"),
+ STLVmTupleGen(ip_min=self.p1_dst_start_ip,
+ ip_max=self.p1_dst_end_ip,
+ port_min=self.p1_dst_start_udp_port,
+ port_max=self.p1_dst_end_udp_port,
+ name="tuple1_dst"),
+ STLVmWrFlowVar(fv_name="tuple1_src.ip", pkt_offset="IP.src"),
+ STLVmWrFlowVar(fv_name="tuple1_dst.ip", pkt_offset="IP.dst"),
+ STLVmFixIpv4(offset="IP"),
+ STLVmWrFlowVar(fv_name="tuple1_src.port", pkt_offset="UDP.sport"),
+ STLVmWrFlowVar(fv_name="tuple1_dst.port", pkt_offset="UDP.dport")
+ ])
+ # Direction 0 --> 1
+ vm2 = STLScVmRaw([
+ STLVmTupleGen(ip_min=self.p2_src_start_ip,
+ ip_max=self.p2_src_end_ip,
+ port_min=self.p2_src_start_udp_port,
+ port_max=self.p2_src_end_udp_port,
+ name="tuple2_src"),
+ STLVmTupleGen(ip_min=self.p2_dst_start_ip,
+ ip_max=self.p2_dst_end_ip,
+ port_min=self.p2_dst_start_udp_port,
+ port_max=self.p2_dst_end_udp_port,
+ name="tuple2_dst"),
+ STLVmWrFlowVar(fv_name="tuple2_src.ip", pkt_offset="IP.src"),
+ STLVmWrFlowVar(fv_name="tuple2_dst.ip", pkt_offset="IP.dst"),
+ STLVmFixIpv4(offset="IP"),
+ STLVmWrFlowVar(fv_name="tuple2_src.port", pkt_offset="UDP.sport"),
+ STLVmWrFlowVar(fv_name="tuple2_dst.port", pkt_offset="UDP.dport")
+ ])
+
+ return base_pkt_a, base_pkt_b, vm1, vm2
+
+
+def register():
+ """Register this traffic profile to T-rex.
+
+ Do not change this function.
+
+ :return: Traffic streams.
+ :rtype: Object
+ """
+ return TrafficStreams()
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+"""Stream profile for T-rex traffic generator.
+
+Stream profile:
+ - Two streams sent in directions 0 --> 1 and 1 --> 0 at the same time.
+ - Packet: ETH / IP / UDP
+ - Direction 0 --> 1:
+ - Source IP address range: 20.0.0.0
+ - Destination IP address range: 12.0.0.2
+ - Source UDP port range: 1024
+ - Destination UDP port range: 1024
+ - Direction 1 --> 0:
+ - Source IP address range: 12.0.0.2
+ - Destination IP address range: 200.0.0.0
+ - Source UDP port range: 1024
+ - Destination UDP port range: 1028
+"""
+
+from trex_stl_lib.api import *
+from profile_trex_stateless_base_class import TrafficStreamsBaseClass
+
+
+class TrafficStreams(TrafficStreamsBaseClass):
+ """Stream profile."""
+
+ def __init__(self):
+ """Initialization and setting of streams' parameters."""
+
+ super(TrafficStreamsBaseClass, self).__init__()
+
+ # IPs used in packet headers.
+ self.p1_src_ip = '20.0.0.0'
+ self.p1_dst_ip = '12.0.0.2'
+
+ self.p2_src_ip = '12.0.0.2'
+ self.p2_dst_ip = '200.0.0.0'
+
+ # UDP ports used in packet headers.
+ self.p1_src_udp_port = 1024
+ self.p1_dst_udp_port = 1024
+
+ self.p2_src_udp_port = 1024
+ self.p2_dst_udp_port = 1028
+
+ def define_packets(self):
+ """Defines the packets to be sent from the traffic generator.
+
+ Packet definition: | ETH | IP | UDP |
+
+ :returns: Packets to be sent from the traffic generator.
+ :rtype: tuple
+ """
+
+ # Direction 0 --> 1
+ base_pkt_a = (Ether() /
+ IP(src=self.p1_src_ip, dst=self.p1_dst_ip, proto=17) /
+ UDP(sport=self.p1_src_udp_port,
+ dport=self.p1_dst_udp_port))
+ # Direction 1 --> 0
+ base_pkt_b = (Ether() /
+ IP(src=self.p2_src_ip, dst=self.p2_dst_ip, proto=17) /
+ UDP(sport=self.p2_src_udp_port,
+ dport=self.p2_dst_udp_port))
+
+ return base_pkt_a, base_pkt_b, None, None
+
+
+def register():
+ """Register this traffic profile to T-rex.
+
+ Do not change this function.
+
+ :return: Traffic streams.
+ :rtype: Object
+ """
+ return TrafficStreams()
- Direction 1 --> 0:
- Source IP address range: 20.20.20.2 - 20.20.20.101
- Destination IP address range: 10.10.10.2 - 10.10.10.101
- - Source UDP port range: 2001-3000
+ - Source UDP port range: 2001 - 3000
- Destination UDP port range: 1001 - 2000
"""
- Direction 1 --> 0:
- Source IP address range: 20.20.20.2 - 20.20.20.11
- Destination IP address range: 10.10.10.2 - 10.10.10.11
- - Source UDP port range: 2001-3000
+ - Source UDP port range: 2001 - 3000
- Destination UDP port range: 1001 - 2000
"""
- Direction 1 --> 0:
- Source IP address range: 20.20.20.2 - 20.20.20.11
- Destination IP address range: 10.10.10.2 - 10.10.10.11
- - Source UDP port range: 2001-2010
+ - Source UDP port range: 2001 - 2010
- Destination UDP port range: 1001 - 1010
"""
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | And Add Fib Table | ${dut1} | 1
| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 |Â vrf=1 | local=${TRUE}
| | And Add Fib Table | ${dut2} | 1
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | And Add Fib Table | ${dut1} | 1
| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 |Â vrf=1 | local=${TRUE}
| | And Add Fib Table | ${dut2} | 1
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
| | ... | ${dut1} | ip4 | dst
| | And Vpp Configures Classify Session L3
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
| | ... | ${dut1} | ip4 | dst
| | And Vpp Configures Classify Session L3
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
-| | And Initialize IPv4 policer 2r3c-'ca' in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
-| | And Initialize IPv4 policer 2r3c-'ca' in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
-| ... | matching MAC addresses of the TG node interfaces.ble standard specifications:* RFC2544.
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
# X520-DA2 bandwidth limit
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 100
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
| ... | applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
-| ... | with 2p10GE NIC X520 Niantic by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}
-| ... | flows per flow-group) with all packets containing Ethernet header, IPv4
-| ... | header with IP protocol=61 and static payload. MAC addresses are
+| ... | with 2p10GE NIC X520 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | And Add Fib Table | ${dut1} | 1
| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 |Â vrf=1 | local=${TRUE}
| | And Add Fib Table | ${dut2} | 1
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | And Add Fib Table | ${dut1} | 1
| | And Vpp Route Add | ${dut1} | 10.10.10.0 | 24 |Â vrf=1 | local=${TRUE}
| | And Add Fib Table | ${dut2} | 1
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
| | ... | ${dut1} | ip4 | dst
| | And Vpp Configures Classify Session L3
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | ${table_idx} | ${skip_n} | ${match_n}= | And Vpp Creates Classify Table L3
| | ... | ${dut1} | ip4 | dst
| | And Vpp Configures Classify Session L3
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
-| | And Initialize IPv4 policer 2r3c-'ca' in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
-| | And Initialize IPv4 policer 2r3c-'ca' in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
-| ... | at line rate and reports total received/sent packets over trial period.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| ...
| ... | *[Top] Network Topologies:* TG-DUT1-DUT2-TG 3-node circular topology\
| ... | with single links between nodes.
-| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for L2 switching of IPv4.
-| ... | *[Cfg] DUT configuration:* DUT1 is configured with L2 bridge domain\
-| ... | and MAC learning enabled. DUT2 is configured with L2 cross-connects.\
-| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
-| ... | DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.\
-| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
-| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
-| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
-| ... | of packets transmitted. NDR and PDR are discovered for different
-| ... | Ethernet L2 frame sizes using MLRsearch library.
-| ... | Test packets are generated by TG on links to DUTs. TG traffic profile
-| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
-| ... | flow-group) with all packets containing Ethernet header, IPv4 header
-| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
-| ... | addresses of the TG node interfaces.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 and DUT2 are configured with IPv4\
+| ... | routing and one static IPv4 /24 route entries. Required ACL rules are\
+| ... | applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested\
+| ... | with 2p10GE NIC X710 Niantic by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUTs. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
| ... | *[Ref] Applicable standard specifications:* RFC2544.
*** Variables ***
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
| | ${ip_nr}= | Set Variable | 10
-| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in 3-node circular topology
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ... | ${s_limit} | ${framesize}
| | And Add NAT to all DUTs
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize NAT44 in 3-node circular topology
+| | When Initialize NAT44 in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Policer
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | IP4FWD | BASE | POLICE_MARK
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 policer test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | two IPv4 ARP entries and policer with 2R3C color-aware configuration.\
+| ... | Policer is applied on links TG - DUT1. DUT1 is tested with 2p10GE\
+| ... | NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv6 header\
+| ... | and generated payload. MAC addresses are matching MAC addresses\
+| ... | of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${cir}= | ${100}
+| ${eir}= | ${150}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${cb} | ${framesize}
+| | Set Test Variable | ${eb} | ${framesize}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Policer
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | IP4FWD | BASE | DOT1Q
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-X710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 policer test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and\
+| ... | two IPv4 ARP entries and policer with 2R3C color-aware configuration.\
+| ... | Policer is applied on links TG - DUT1. DUT1 is tested with 2p10GE\
+| ... | NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per\
+| ... | flow-group) with all packets containing Ethernet header, IPv6 header\
+| ... | and generated payload. MAC addresses are matching MAC addresses\
+| ... | of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+| ${cir}= | ${100}
+| ${eir}= | ${150}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | Set Test Variable | ${cb} | ${framesize}
+| | Set Test Variable | ${eb} | ${framesize}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 2-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_limit} | ${framesize}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 2-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | BASE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and
+| ... | one static IPv4 /18 route entries.
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 1 flow per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-1u1p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-X710 | ETH | IP4FWD | FEATURE | NAT44 | BASE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-X710
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and
+| ... | one static IPv4 /18 route entries.
+| ... | DUT1 is tested with 2p10GE NIC X710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 1 flow per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# X710 bandwidth limit
+| ${s_limit}= | ${10000000000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-1u1p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_limit} | ${framesize}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Policer
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | IP4FWD | BASE | POLICE_MARK
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 policer test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and
+| ... | two IPv4 ARP entries and policer with 2R3C color-aware configuration.
+| ... | Policer is applied on links TG - DUT1. DUT1 is tested with 2p25GE
+| ... | NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate tests TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv6 header
+| ... | and generated payload. MAC addresses are matching MAC addresses
+| ... | of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+| ${cir}= | ${100}
+| ${eir}= | ${150}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${cb} | ${framesize}
+| | Set Test Variable | ${eb} | ${framesize}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ipolicemarkbase-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Library | resources.libraries.python.Policer
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | IP4FWD | BASE | DOT1Q
+| ...
+| Suite Setup | Set up 2-node performance topology with DUT's NIC model
+| ... | L3 | Intel-XXV710
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 policer test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4 for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and
+| ... | two IPv4 ARP entries and policer with 2R3C color-aware configuration.
+| ... | Policer is applied on links TG - DUT1. DUT1 is tested with 2p25GE
+| ... | NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 253 flows per
+| ... | flow-group) with all packets containing Ethernet header, IPv6 header
+| ... | and generated payload. MAC addresses are matching MAC addresses
+| ... | of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544, RFC2698.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+| ${cir}= | ${100}
+| ${eir}= | ${150}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4-ip4src253
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | Set Test Variable | ${cb} | ${framesize}
+| | Set Test Variable | ${eb} | ${framesize}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize IPv4 forwarding in circular topology
+| | And Initialize IPv4 policer 2r3c-'ca' in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4-ip4base-ipolicemarkbase-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
| | ...
| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
| | And Add PCI devices to all DUTs
-| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 2-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 2-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sf-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sl-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL1 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 1
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATEFUL
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit+reflect
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic\
+| ... | at line rate and reports total received/sent packets over trial period.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sl-10kflows-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | ACL | ACL_STATELESS
+| ... | IACL | ACL50 | 10k_FLOWS
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with ACL
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput IPv4 test cases with ACL*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology\
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing.\
+| ... | Required ACL rules are applied to input paths of both DUT1 intefaces.\
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop\
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop\
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage\
+| ... | of packets transmitted. NDR and PDR are discovered for different\
+| ... | Ethernet L2 frame sizes using MLRsearch library.\
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile\
+| ... | contains two L3 flow-groups (flow-group per direction, ${flows_per_dir}\
+| ... | flows per flow-group) with all packets containing Ethernet header, IPv4\
+| ... | header with IP protocol=61 and static payload. MAC addresses are\
+| ... | matching MAC addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+
+# ACL test setup
+| ${acl_action}= | permit
+| ${acl_apply_type}= | input
+| ${no_hit_aces_number}= | 50
+| ${flows_per_dir}= | 10k
+
+# starting points for non-hitting ACLs
+| ${src_ip_start}= | 30.30.30.1
+| ${dst_ip_start}= | 40.40.40.1
+| ${ip_step}= | ${1}
+| ${sport_start}= | ${1000}
+| ${dport_start}= | ${1000}
+| ${port_step}= | ${1}
+| ${trex_stream1_subnet}= | 10.10.10.0/24
+| ${trex_stream2_subnet}= | 20.20.20.0/24
+
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-10u1000p-conc
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Apply startup configuration on all VPP DUTs
+| | ${ip_nr}= | Set Variable | 10
+| | When Initialize IPv4 routing for '${ip_nr}' addresses with IPv4 ACLs on DUT1 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | MRR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | NAT44 | BASE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance mrr test
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *Raw results NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and
+| ... | one static IPv4 /18 route entries.
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* In MaxReceivedRate test TG sends traffic
+| ... | at line rate and reports total received/sent packets over trial period.
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 1 flow per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-1u1p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure MaxReceivedRate for ${framesize}B frames using single\
+| | ... | trial throughput test.
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Traffic should pass with maximum rate
+| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-nat44-mrr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
--- /dev/null
+# Copyright (c) 2018 Cisco and/or its affiliates.
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at:
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+*** Settings ***
+| Resource | resources/libraries/robot/performance/performance_setup.robot
+| Resource | resources/libraries/robot/ip/nat.robot
+| Resource | resources/libraries/robot/shared/traffic.robot
+| ...
+| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
+| ... | NIC_Intel-XXV710 | ETH | IP4FWD | FEATURE | NAT44 | BASE
+| ...
+| Suite Setup | Run Keywords
+| ... | Set up 2-node performance topology with DUT's NIC model | L3
+| ... | Intel-XXV710
+| ... | AND | Set up performance test suite with NAT
+| Suite Teardown | Tear down 2-node performance topology
+| ...
+| Test Setup | Set up performance test
+| ...
+| Test Teardown | Tear down performance discovery test | ${min_rate}pps
+| ... | ${framesize} | ${traffic_profile}
+| ...
+| Test Template | Local Template
+| ...
+| Documentation | *RFC2544: Pkt throughput NAT44 performance test cases*
+| ...
+| ... | *[Top] Network Topologies:* TG-DUT1-TG 2-node circular topology
+| ... | with single links between nodes.
+| ... | *[Enc] Packet Encapsulations:* Eth-IPv4-UDP for IPv4 routing.
+| ... | *[Cfg] DUT configuration:* DUT1 is configured with IPv4 routing and
+| ... | one static IPv4 /18 route entries.
+| ... | DUT1 is tested with 2p25GE NIC XXV710 by Intel.
+| ... | *[Ver] TG verification:* TG finds and reports throughput NDR (Non Drop
+| ... | Rate) with zero packet loss tolerance or throughput PDR (Partial Drop
+| ... | Rate) with non-zero packet loss tolerance (LT) expressed in percentage
+| ... | of packets transmitted. NDR and PDR are discovered for different
+| ... | Ethernet L2 frame sizes using MLRsearch library.
+| ... | Test packets are generated by TG on links to DUT1. TG traffic profile
+| ... | contains two L3 flow-groups (flow-group per direction, 1 flow per
+| ... | flow-group) with all packets containing Ethernet header, IPv4 header
+| ... | with IP protocol=61 and static payload. MAC addresses are matching MAC
+| ... | addresses of the TG node interfaces.
+| ... | *[Ref] Applicable standard specifications:* RFC2544.
+
+*** Variables ***
+# XXV710-DA2 bandwidth limit ~49Gbps/2=24.5Gbps
+| ${s_24.5G} | ${24500000000}
+# XXV710-DA2 Mpps limit 37.5Mpps/2=18.75Mpps
+| ${s_18.75Mpps} | ${18750000}
+# Traffic profile:
+| ${traffic_profile}= | trex-sl-2n-ethip4udp-1u1p
+
+*** Keywords ***
+| Local Template
+| | ...
+| | [Documentation]
+| | ... | [Cfg] DUT runs IPv4 routing config.
+| | ... | Each DUT uses ${phy_cores} physical core(s) for worker threads.
+| | ... | [Ver] Measure NDR and PDR values using MLRsearch algorithm.\
+| | ...
+| | ... | *Arguments:*
+| | ... | - framesize - Framesize in Bytes in integer or string (IMIX_v4_1).
+| | ... | Type: integer, string
+| | ... | - phy_cores - Number of physical cores. Type: integer
+| | ... | - rxq - Number of RX queues, default value: ${None}. Type: integer
+| | ...
+| | [Arguments] | ${framesize} | ${phy_cores} | ${rxq}=${None}
+| | ...
+| | Set Test Variable | ${framesize}
+| | Set Test Variable | ${min_rate} | ${10000}
+| | ...
+| | Given Add worker threads and rxqueues to all DUTs | ${phy_cores} | ${rxq}
+| | And Add PCI devices to all DUTs
+| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo And Handle Multi Seg
+| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
+| | And Add NAT to all DUTs
+| | And Apply startup configuration on all VPP DUTs
+| | When Initialize NAT44 in circular topology
+| | Then Find NDR and PDR intervals using optimized search
+| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
+
+*** Test Cases ***
+| tc01-64B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 1C
+| | framesize=${64} | phy_cores=${1}
+
+| tc02-64B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 2C
+| | framesize=${64} | phy_cores=${2}
+
+| tc03-64B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 64B | 4C
+| | framesize=${64} | phy_cores=${4}
+
+| tc04-1518B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 1C
+| | framesize=${1518} | phy_cores=${1}
+
+| tc05-1518B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 2C
+| | framesize=${1518} | phy_cores=${2}
+
+| tc06-1518B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 1518B | 4C
+| | framesize=${1518} | phy_cores=${4}
+
+| tc07-9000B-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 1C
+| | framesize=${9000} | phy_cores=${1}
+
+| tc08-9000B-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 2C
+| | framesize=${9000} | phy_cores=${2}
+
+| tc09-9000B-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | 9000B | 4C
+| | framesize=${9000} | phy_cores=${4}
+
+| tc10-IMIX-1c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 1C
+| | framesize=IMIX_v4_1 | phy_cores=${1}
+
+| tc11-IMIX-2c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 2C
+| | framesize=IMIX_v4_1 | phy_cores=${2}
+
+| tc12-IMIX-4c-ethip4udp-ip4base-nat44-ndrpdr
+| | [Tags] | IMIX | 4C
+| | framesize=IMIX_v4_1 | phy_cores=${4}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo
| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Traffic should pass with maximum rate
| | ... | ${max_rate}pps | ${framesize} | ${traffic_profile}
| | ${max_rate} | ${jumbo} = | Get Max Rate And Jumbo
| | ... | ${s_24.5G} | ${framesize} | pps_limit=${s_18.75Mpps}
| | And Apply startup configuration on all VPP DUTs
-| | When Initialize IPv4 forwarding in 3-node circular topology
+| | When Initialize IPv4 forwarding in circular topology
| | Then Find NDR and PDR intervals using optimized search
| | ... | ${framesize} | ${traffic_profile} | ${min_rate} | ${max_rate}
Code Review / csit.git / commitdiff