New upstream version 18.08

[deb_dpdk.git] / drivers / net / bnxt / hsi_struct_def_dpdk.h

/* SPDX-License-Identifier: BSD-3-Clause
 * Copyright (c) 2014-2018 Broadcom Limited
 * All rights reserved.
 *
 * DO NOT MODIFY!!! This file is automatically generated.
 */

#ifndef _HSI_STRUCT_DEF_DPDK_H_
#define _HSI_STRUCT_DEF_DPDK_H_

/* This is the HWRM command header. */
/* hwrm_cmd_hdr (size:128b/16B) */
struct hwrm_cmd_hdr {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* This is the HWRM response header. */
/* hwrm_resp_hdr (size:64b/8B) */
struct hwrm_resp_hdr {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
} __attribute__((packed));

/*
 * TLV encapsulated message. Use the TLV type field of the
 * TLV to determine the type of message encapsulated.
 */
#define CMD_DISCR_TLV_ENCAP UINT32_C(0x8000)
#define CMD_DISCR_LAST     CMD_DISCR_TLV_ENCAP


/* HWRM request message */
#define TLV_TYPE_HWRM_REQUEST                    UINT32_C(0x1)
/* HWRM response message */
#define TLV_TYPE_HWRM_RESPONSE                   UINT32_C(0x2)
/* RoCE slow path command */
#define TLV_TYPE_ROCE_SP_COMMAND                 UINT32_C(0x3)
/* Engine CKV - The device's serial number. */
#define TLV_TYPE_ENGINE_CKV_DEVICE_SERIAL_NUMBER UINT32_C(0x8001)
/* Engine CKV - Per-function random nonce data. */
#define TLV_TYPE_ENGINE_CKV_NONCE                UINT32_C(0x8002)
/* Engine CKV - Initialization vector. */
#define TLV_TYPE_ENGINE_CKV_IV                   UINT32_C(0x8003)
/* Engine CKV - Authentication tag. */
#define TLV_TYPE_ENGINE_CKV_AUTH_TAG             UINT32_C(0x8004)
/* Engine CKV - The encrypted data. */
#define TLV_TYPE_ENGINE_CKV_CIPHERTEXT           UINT32_C(0x8005)
/* Engine CKV - Supported algorithms. */
#define TLV_TYPE_ENGINE_CKV_ALGORITHMS           UINT32_C(0x8006)
/* Engine CKV - The EC curve name and ECC public key information. */
#define TLV_TYPE_ENGINE_CKV_ECC_PUBLIC_KEY       UINT32_C(0x8007)
/* Engine CKV - The ECDSA signature. */
#define TLV_TYPE_ENGINE_CKV_ECDSA_SIGNATURE      UINT32_C(0x8008)
#define TLV_TYPE_LAST \
        TLV_TYPE_ENGINE_CKV_ECDSA_SIGNATURE


/* tlv (size:64b/8B) */
struct tlv {
        /*
         * The command discriminator is used to differentiate between various
         * types of HWRM messages. This includes legacy HWRM and RoCE slowpath
         * command messages as well as newer TLV encapsulated HWRM commands.
         *
         * For TLV encapsulated messages this field must be 0x8000.
         */
        uint16_t        cmd_discr;
        uint8_t reserved_8b;
        uint8_t flags;
        /*
         * Indicates the presence of additional TLV encapsulated data
         * follows this TLV.
         */
        #define TLV_FLAGS_MORE         UINT32_C(0x1)
        /* Last TLV in a sequence of TLVs. */
        #define TLV_FLAGS_MORE_LAST      UINT32_C(0x0)
        /* More TLVs follow this TLV. */
        #define TLV_FLAGS_MORE_NOT_LAST  UINT32_C(0x1)
        /*
         * When an HWRM receiver detects a TLV type that it does not
         * support with the TLV required flag set, the receiver must
         * reject the HWRM message with an error code indicating an
         * unsupported TLV type.
         */
        #define TLV_FLAGS_REQUIRED     UINT32_C(0x2)
        /* No */
        #define TLV_FLAGS_REQUIRED_NO    (UINT32_C(0x0) << 1)
        /* Yes */
        #define TLV_FLAGS_REQUIRED_YES   (UINT32_C(0x1) << 1)
        #define TLV_FLAGS_REQUIRED_LAST TLV_FLAGS_REQUIRED_YES
        /*
         * This field defines the TLV type value which is divided into
         * two ranges to differentiate between global and local TLV types.
         * Global TLV types must be unique across all defined TLV types.
         * Local TLV types are valid only for extensions to a given
         * HWRM message and may be repeated across different HWRM message
         * types. There is a direct correlation of each HWRM message type
         * to a single global TLV type value.
         *
         * Global TLV range: `0 - (63k-1)`
         *
         * Local TLV range: `63k - (64k-1)`
         */
        uint16_t        tlv_type;
        /*
         * Length of the message data encapsulated by this TLV in bytes.
         * This length does not include the size of the TLV header itself
         * and it must be an integer multiple of 8B.
         */
        uint16_t        length;
} __attribute__((packed));

/* Input */
/* input (size:128b/16B) */
struct input {
        /*
         * This value indicates what type of request this is.  The format
         * for the rest of the command is determined by this field.
         */
        uint16_t        req_type;
        /*
         * This value indicates the what completion ring the request will
         * be optionally completed on.  If the value is -1, then no
         * CR completion will be generated.  Any other value must be a
         * valid CR ring_id value for this function.
         */
        uint16_t        cmpl_ring;
        /* This value indicates the command sequence number. */
        uint16_t        seq_id;
        /*
         * Target ID of this command.
         *
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * This is the host address where the response will be written
         * when the request is complete.  This area must be 16B aligned
         * and must be cleared to zero before the request is made.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* Output */
/* output (size:64b/8B) */
struct output {
        /*
         * Pass/Fail or error type
         *
         * Note: receiver to verify the in parameters, and fail the call
         * with an error when appropriate
         */
        uint16_t        error_code;
        /* This field returns the type of original request. */
        uint16_t        req_type;
        /* This field provides original sequence number of the command. */
        uint16_t        seq_id;
        /*
         * This field is the length of the response in bytes.  The
         * last byte of the response is a valid flag that will read
         * as '1' when the command has been completely written to
         * memory.
         */
        uint16_t        resp_len;
} __attribute__((packed));

/* Short Command Structure */
/* hwrm_short_input (size:128b/16B) */
struct hwrm_short_input {
        /*
         * This field indicates the type of request in the request buffer.
         * The format for the rest of the command (request) is determined
         * by this field.
         */
        uint16_t        req_type;
        /*
         * This field indicates a signature that is used to identify short
         * form of the command listed here. This field shall be set to
         * 17185 (0x4321).
         */
        uint16_t        signature;
        /* Signature indicating this is a short form of HWRM command */
        #define HWRM_SHORT_INPUT_SIGNATURE_SHORT_CMD UINT32_C(0x4321)
        #define HWRM_SHORT_INPUT_SIGNATURE_LAST \
                HWRM_SHORT_INPUT_SIGNATURE_SHORT_CMD
        /* Reserved for future use. */
        uint16_t        unused_0;
        /* This value indicates the length of the request. */
        uint16_t        size;
        /*
         * This is the host address where the request was written.
         * This area must be 16B aligned.
         */
        uint64_t        req_addr;
} __attribute__((packed));

/*
 * Command numbering
 * # NOTE - definitions already in hwrm_req_type, in hwrm_types.yaml
 * #        So only structure definition is provided here.
 */
/* cmd_nums (size:64b/8B) */
struct cmd_nums {
        /*
         * This version of the specification defines the commands listed in
         * the table below. The following are general implementation
         * requirements for these commands:
         *
         * # All commands listed below that are marked neither
         * reserved nor experimental shall be implemented by the HWRM.
         * # A HWRM client compliant to this specification should not use
         * commands outside of the list below.
         * # A HWRM client compliant to this specification should not use
         * command numbers marked reserved below.
         * # A command marked experimental below may not be implemented
         * by the HWRM.
         * # A command marked experimental may change in the
         * future version of the HWRM specification.
         * # A command not listed below may be implemented by the HWRM.
         * The behavior of commands that are not listed below is outside
         * the scope of this specification.
         */
        uint16_t        req_type;
        #define HWRM_VER_GET                              UINT32_C(0x0)
        #define HWRM_FUNC_BUF_UNRGTR                      UINT32_C(0xe)
        #define HWRM_FUNC_VF_CFG                          UINT32_C(0xf)
        /* Reserved for future use. */
        #define HWRM_RESERVED1                            UINT32_C(0x10)
        #define HWRM_FUNC_RESET                           UINT32_C(0x11)
        #define HWRM_FUNC_GETFID                          UINT32_C(0x12)
        #define HWRM_FUNC_VF_ALLOC                        UINT32_C(0x13)
        #define HWRM_FUNC_VF_FREE                         UINT32_C(0x14)
        #define HWRM_FUNC_QCAPS                           UINT32_C(0x15)
        #define HWRM_FUNC_QCFG                            UINT32_C(0x16)
        #define HWRM_FUNC_CFG                             UINT32_C(0x17)
        #define HWRM_FUNC_QSTATS                          UINT32_C(0x18)
        #define HWRM_FUNC_CLR_STATS                       UINT32_C(0x19)
        #define HWRM_FUNC_DRV_UNRGTR                      UINT32_C(0x1a)
        #define HWRM_FUNC_VF_RESC_FREE                    UINT32_C(0x1b)
        #define HWRM_FUNC_VF_VNIC_IDS_QUERY               UINT32_C(0x1c)
        #define HWRM_FUNC_DRV_RGTR                        UINT32_C(0x1d)
        #define HWRM_FUNC_DRV_QVER                        UINT32_C(0x1e)
        #define HWRM_FUNC_BUF_RGTR                        UINT32_C(0x1f)
        #define HWRM_PORT_PHY_CFG                         UINT32_C(0x20)
        #define HWRM_PORT_MAC_CFG                         UINT32_C(0x21)
        /* Experimental */
        #define HWRM_PORT_TS_QUERY                        UINT32_C(0x22)
        #define HWRM_PORT_QSTATS                          UINT32_C(0x23)
        #define HWRM_PORT_LPBK_QSTATS                     UINT32_C(0x24)
        /* Experimental */
        #define HWRM_PORT_CLR_STATS                       UINT32_C(0x25)
        /* Experimental */
        #define HWRM_PORT_LPBK_CLR_STATS                  UINT32_C(0x26)
        #define HWRM_PORT_PHY_QCFG                        UINT32_C(0x27)
        #define HWRM_PORT_MAC_QCFG                        UINT32_C(0x28)
        /* Experimental */
        #define HWRM_PORT_MAC_PTP_QCFG                    UINT32_C(0x29)
        #define HWRM_PORT_PHY_QCAPS                       UINT32_C(0x2a)
        #define HWRM_PORT_PHY_I2C_WRITE                   UINT32_C(0x2b)
        #define HWRM_PORT_PHY_I2C_READ                    UINT32_C(0x2c)
        #define HWRM_PORT_LED_CFG                         UINT32_C(0x2d)
        #define HWRM_PORT_LED_QCFG                        UINT32_C(0x2e)
        #define HWRM_PORT_LED_QCAPS                       UINT32_C(0x2f)
        #define HWRM_QUEUE_QPORTCFG                       UINT32_C(0x30)
        #define HWRM_QUEUE_QCFG                           UINT32_C(0x31)
        #define HWRM_QUEUE_CFG                            UINT32_C(0x32)
        #define HWRM_FUNC_VLAN_CFG                        UINT32_C(0x33)
        #define HWRM_FUNC_VLAN_QCFG                       UINT32_C(0x34)
        #define HWRM_QUEUE_PFCENABLE_QCFG                 UINT32_C(0x35)
        #define HWRM_QUEUE_PFCENABLE_CFG                  UINT32_C(0x36)
        #define HWRM_QUEUE_PRI2COS_QCFG                   UINT32_C(0x37)
        #define HWRM_QUEUE_PRI2COS_CFG                    UINT32_C(0x38)
        #define HWRM_QUEUE_COS2BW_QCFG                    UINT32_C(0x39)
        #define HWRM_QUEUE_COS2BW_CFG                     UINT32_C(0x3a)
        /* Experimental */
        #define HWRM_QUEUE_DSCP_QCAPS                     UINT32_C(0x3b)
        /* Experimental */
        #define HWRM_QUEUE_DSCP2PRI_QCFG                  UINT32_C(0x3c)
        /* Experimental */
        #define HWRM_QUEUE_DSCP2PRI_CFG                   UINT32_C(0x3d)
        #define HWRM_VNIC_ALLOC                           UINT32_C(0x40)
        #define HWRM_VNIC_FREE                            UINT32_C(0x41)
        #define HWRM_VNIC_CFG                             UINT32_C(0x42)
        #define HWRM_VNIC_QCFG                            UINT32_C(0x43)
        #define HWRM_VNIC_TPA_CFG                         UINT32_C(0x44)
        /* Experimental */
        #define HWRM_VNIC_TPA_QCFG                        UINT32_C(0x45)
        #define HWRM_VNIC_RSS_CFG                         UINT32_C(0x46)
        #define HWRM_VNIC_RSS_QCFG                        UINT32_C(0x47)
        #define HWRM_VNIC_PLCMODES_CFG                    UINT32_C(0x48)
        #define HWRM_VNIC_PLCMODES_QCFG                   UINT32_C(0x49)
        #define HWRM_VNIC_QCAPS                           UINT32_C(0x4a)
        #define HWRM_RING_ALLOC                           UINT32_C(0x50)
        #define HWRM_RING_FREE                            UINT32_C(0x51)
        #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS        UINT32_C(0x52)
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS     UINT32_C(0x53)
        #define HWRM_RING_RESET                           UINT32_C(0x5e)
        #define HWRM_RING_GRP_ALLOC                       UINT32_C(0x60)
        #define HWRM_RING_GRP_FREE                        UINT32_C(0x61)
        /* Reserved for future use. */
        #define HWRM_RESERVED5                            UINT32_C(0x64)
        /* Reserved for future use. */
        #define HWRM_RESERVED6                            UINT32_C(0x65)
        #define HWRM_VNIC_RSS_COS_LB_CTX_ALLOC            UINT32_C(0x70)
        #define HWRM_VNIC_RSS_COS_LB_CTX_FREE             UINT32_C(0x71)
        #define HWRM_CFA_L2_FILTER_ALLOC                  UINT32_C(0x90)
        #define HWRM_CFA_L2_FILTER_FREE                   UINT32_C(0x91)
        #define HWRM_CFA_L2_FILTER_CFG                    UINT32_C(0x92)
        #define HWRM_CFA_L2_SET_RX_MASK                   UINT32_C(0x93)
        #define HWRM_CFA_VLAN_ANTISPOOF_CFG               UINT32_C(0x94)
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC              UINT32_C(0x95)
        #define HWRM_CFA_TUNNEL_FILTER_FREE               UINT32_C(0x96)
        /* Experimental */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC               UINT32_C(0x97)
        /* Experimental */
        #define HWRM_CFA_ENCAP_RECORD_FREE                UINT32_C(0x98)
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC              UINT32_C(0x99)
        #define HWRM_CFA_NTUPLE_FILTER_FREE               UINT32_C(0x9a)
        #define HWRM_CFA_NTUPLE_FILTER_CFG                UINT32_C(0x9b)
        /* Experimental */
        #define HWRM_CFA_EM_FLOW_ALLOC                    UINT32_C(0x9c)
        /* Experimental */
        #define HWRM_CFA_EM_FLOW_FREE                     UINT32_C(0x9d)
        /* Experimental */
        #define HWRM_CFA_EM_FLOW_CFG                      UINT32_C(0x9e)
        #define HWRM_TUNNEL_DST_PORT_QUERY                UINT32_C(0xa0)
        #define HWRM_TUNNEL_DST_PORT_ALLOC                UINT32_C(0xa1)
        #define HWRM_TUNNEL_DST_PORT_FREE                 UINT32_C(0xa2)
        #define HWRM_STAT_CTX_ALLOC                       UINT32_C(0xb0)
        #define HWRM_STAT_CTX_FREE                        UINT32_C(0xb1)
        #define HWRM_STAT_CTX_QUERY                       UINT32_C(0xb2)
        #define HWRM_STAT_CTX_CLR_STATS                   UINT32_C(0xb3)
        #define HWRM_PORT_QSTATS_EXT                      UINT32_C(0xb4)
        #define HWRM_FW_RESET                             UINT32_C(0xc0)
        #define HWRM_FW_QSTATUS                           UINT32_C(0xc1)
        /* Experimental */
        #define HWRM_FW_SET_TIME                          UINT32_C(0xc8)
        /* Experimental */
        #define HWRM_FW_GET_TIME                          UINT32_C(0xc9)
        /* Experimental */
        #define HWRM_FW_SET_STRUCTURED_DATA               UINT32_C(0xca)
        /* Experimental */
        #define HWRM_FW_GET_STRUCTURED_DATA               UINT32_C(0xcb)
        /* Experimental */
        #define HWRM_FW_IPC_MAILBOX                       UINT32_C(0xcc)
        #define HWRM_EXEC_FWD_RESP                        UINT32_C(0xd0)
        #define HWRM_REJECT_FWD_RESP                      UINT32_C(0xd1)
        #define HWRM_FWD_RESP                             UINT32_C(0xd2)
        #define HWRM_FWD_ASYNC_EVENT_CMPL                 UINT32_C(0xd3)
        #define HWRM_OEM_CMD                              UINT32_C(0xd4)
        #define HWRM_TEMP_MONITOR_QUERY                   UINT32_C(0xe0)
        #define HWRM_WOL_FILTER_ALLOC                     UINT32_C(0xf0)
        #define HWRM_WOL_FILTER_FREE                      UINT32_C(0xf1)
        #define HWRM_WOL_FILTER_QCFG                      UINT32_C(0xf2)
        #define HWRM_WOL_REASON_QCFG                      UINT32_C(0xf3)
        /* Experimental */
        #define HWRM_CFA_METER_PROFILE_ALLOC              UINT32_C(0xf5)
        /* Experimental */
        #define HWRM_CFA_METER_PROFILE_FREE               UINT32_C(0xf6)
        /* Experimental */
        #define HWRM_CFA_METER_PROFILE_CFG                UINT32_C(0xf7)
        /* Experimental */
        #define HWRM_CFA_METER_INSTANCE_ALLOC             UINT32_C(0xf8)
        /* Experimental */
        #define HWRM_CFA_METER_INSTANCE_FREE              UINT32_C(0xf9)
        /* Experimental */
        #define HWRM_CFA_VFR_ALLOC                        UINT32_C(0xfd)
        /* Experimental */
        #define HWRM_CFA_VFR_FREE                         UINT32_C(0xfe)
        /* Experimental */
        #define HWRM_CFA_VF_PAIR_ALLOC                    UINT32_C(0x100)
        /* Experimental */
        #define HWRM_CFA_VF_PAIR_FREE                     UINT32_C(0x101)
        /* Experimental */
        #define HWRM_CFA_VF_PAIR_INFO                     UINT32_C(0x102)
        /* Experimental */
        #define HWRM_CFA_FLOW_ALLOC                       UINT32_C(0x103)
        /* Experimental */
        #define HWRM_CFA_FLOW_FREE                        UINT32_C(0x104)
        /* Experimental */
        #define HWRM_CFA_FLOW_FLUSH                       UINT32_C(0x105)
        /* Experimental */
        #define HWRM_CFA_FLOW_STATS                       UINT32_C(0x106)
        /* Experimental */
        #define HWRM_CFA_FLOW_INFO                        UINT32_C(0x107)
        /* Experimental */
        #define HWRM_CFA_DECAP_FILTER_ALLOC               UINT32_C(0x108)
        /* Experimental */
        #define HWRM_CFA_DECAP_FILTER_FREE                UINT32_C(0x109)
        #define HWRM_CFA_VLAN_ANTISPOOF_QCFG              UINT32_C(0x10a)
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC       UINT32_C(0x10b)
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE        UINT32_C(0x10c)
        /* Experimental */
        #define HWRM_CFA_PAIR_ALLOC                       UINT32_C(0x10d)
        /* Experimental */
        #define HWRM_CFA_PAIR_FREE                        UINT32_C(0x10e)
        /* Experimental */
        #define HWRM_CFA_PAIR_INFO                        UINT32_C(0x10f)
        /* Experimental */
        #define HWRM_FW_IPC_MSG                           UINT32_C(0x110)
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO        UINT32_C(0x111)
        /* Engine CKV - Ping the device and SRT firmware to get the public key. */
        #define HWRM_ENGINE_CKV_HELLO                     UINT32_C(0x12d)
        /* Engine CKV - Get the current allocation status of keys provisioned in the key vault. */
        #define HWRM_ENGINE_CKV_STATUS                    UINT32_C(0x12e)
        /* Engine CKV - Add a new CKEK used to encrypt keys. */
        #define HWRM_ENGINE_CKV_CKEK_ADD                  UINT32_C(0x12f)
        /* Engine CKV - Delete a previously added CKEK. */
        #define HWRM_ENGINE_CKV_CKEK_DELETE               UINT32_C(0x130)
        /* Engine CKV - Add a new key to the key vault. */
        #define HWRM_ENGINE_CKV_KEY_ADD                   UINT32_C(0x131)
        /* Engine CKV - Delete a key from the key vault. */
        #define HWRM_ENGINE_CKV_KEY_DELETE                UINT32_C(0x132)
        /* Engine CKV - Delete all keys from the key vault. */
        #define HWRM_ENGINE_CKV_FLUSH                     UINT32_C(0x133)
        /* Engine CKV - Get random data. */
        #define HWRM_ENGINE_CKV_RNG_GET                   UINT32_C(0x134)
        /* Engine CKV - Generate and encrypt a new AES key. */
        #define HWRM_ENGINE_CKV_KEY_GEN                   UINT32_C(0x135)
        /* Engine - Query the available queue groups configuration. */
        #define HWRM_ENGINE_QG_CONFIG_QUERY               UINT32_C(0x13c)
        /* Engine - Query the queue groups assigned to a function. */
        #define HWRM_ENGINE_QG_QUERY                      UINT32_C(0x13d)
        /* Engine - Query the available queue group meter profile configuration. */
        #define HWRM_ENGINE_QG_METER_PROFILE_CONFIG_QUERY UINT32_C(0x13e)
        /* Engine - Query the configuration of a queue group meter profile. */
        #define HWRM_ENGINE_QG_METER_PROFILE_QUERY        UINT32_C(0x13f)
        /* Engine - Allocate a queue group meter profile. */
        #define HWRM_ENGINE_QG_METER_PROFILE_ALLOC        UINT32_C(0x140)
        /* Engine - Free a queue group meter profile. */
        #define HWRM_ENGINE_QG_METER_PROFILE_FREE         UINT32_C(0x141)
        /* Engine - Query the meters assigned to a queue group. */
        #define HWRM_ENGINE_QG_METER_QUERY                UINT32_C(0x142)
        /* Engine - Bind a queue group meter profile to a queue group. */
        #define HWRM_ENGINE_QG_METER_BIND                 UINT32_C(0x143)
        /* Engine - Unbind a queue group meter profile from a queue group. */
        #define HWRM_ENGINE_QG_METER_UNBIND               UINT32_C(0x144)
        /* Engine - Bind a queue group to a function. */
        #define HWRM_ENGINE_QG_FUNC_BIND                  UINT32_C(0x145)
        /* Engine - Query the scheduling group configuration. */
        #define HWRM_ENGINE_SG_CONFIG_QUERY               UINT32_C(0x146)
        /* Engine - Query the queue groups assigned to a scheduling group. */
        #define HWRM_ENGINE_SG_QUERY                      UINT32_C(0x147)
        /* Engine - Query the configuration of a scheduling group's meter profiles. */
        #define HWRM_ENGINE_SG_METER_QUERY                UINT32_C(0x148)
        /* Engine - Configure a scheduling group's meter profiles. */
        #define HWRM_ENGINE_SG_METER_CONFIG               UINT32_C(0x149)
        /* Engine - Bind a queue group to a scheduling group. */
        #define HWRM_ENGINE_SG_QG_BIND                    UINT32_C(0x14a)
        /* Engine - Unbind a queue group from its scheduling group. */
        #define HWRM_ENGINE_QG_SG_UNBIND                  UINT32_C(0x14b)
        /* Engine - Query the Engine configuration. */
        #define HWRM_ENGINE_CONFIG_QUERY                  UINT32_C(0x154)
        /* Engine - Configure the statistics accumulator for an Engine. */
        #define HWRM_ENGINE_STATS_CONFIG                  UINT32_C(0x155)
        /* Engine - Clear the statistics accumulator for an Engine. */
        #define HWRM_ENGINE_STATS_CLEAR                   UINT32_C(0x156)
        /* Engine - Query the statistics accumulator for an Engine. */
        #define HWRM_ENGINE_STATS_QUERY                   UINT32_C(0x157)
        /* Engine - Allocate an Engine RQ. */
        #define HWRM_ENGINE_RQ_ALLOC                      UINT32_C(0x15e)
        /* Engine - Free an Engine RQ. */
        #define HWRM_ENGINE_RQ_FREE                       UINT32_C(0x15f)
        /* Engine - Allocate an Engine CQ. */
        #define HWRM_ENGINE_CQ_ALLOC                      UINT32_C(0x160)
        /* Engine - Free an Engine CQ. */
        #define HWRM_ENGINE_CQ_FREE                       UINT32_C(0x161)
        /* Engine - Allocate an NQ. */
        #define HWRM_ENGINE_NQ_ALLOC                      UINT32_C(0x162)
        /* Engine - Free an NQ. */
        #define HWRM_ENGINE_NQ_FREE                       UINT32_C(0x163)
        /* Engine - Set the on-die RQE credit update location. */
        #define HWRM_ENGINE_ON_DIE_RQE_CREDITS            UINT32_C(0x164)
        /* Experimental */
        #define HWRM_FUNC_RESOURCE_QCAPS                  UINT32_C(0x190)
        /* Experimental */
        #define HWRM_FUNC_VF_RESOURCE_CFG                 UINT32_C(0x191)
        /* Experimental */
        #define HWRM_FUNC_BACKING_STORE_QCAPS             UINT32_C(0x192)
        /* Experimental */
        #define HWRM_FUNC_BACKING_STORE_CFG               UINT32_C(0x193)
        /* Experimental */
        #define HWRM_FUNC_BACKING_STORE_QCFG              UINT32_C(0x194)
        /* Experimental */
        #define HWRM_SELFTEST_QLIST                       UINT32_C(0x200)
        /* Experimental */
        #define HWRM_SELFTEST_EXEC                        UINT32_C(0x201)
        /* Experimental */
        #define HWRM_SELFTEST_IRQ                         UINT32_C(0x202)
        /* Experimental */
        #define HWRM_SELFTEST_RETRIEVE_SERDES_DATA        UINT32_C(0x203)
        /* Experimental */
        #define HWRM_PCIE_QSTATS                          UINT32_C(0x204)
        /* Experimental */
        #define HWRM_DBG_READ_DIRECT                      UINT32_C(0xff10)
        /* Experimental */
        #define HWRM_DBG_READ_INDIRECT                    UINT32_C(0xff11)
        /* Experimental */
        #define HWRM_DBG_WRITE_DIRECT                     UINT32_C(0xff12)
        /* Experimental */
        #define HWRM_DBG_WRITE_INDIRECT                   UINT32_C(0xff13)
        #define HWRM_DBG_DUMP                             UINT32_C(0xff14)
        /* Experimental */
        #define HWRM_DBG_ERASE_NVM                        UINT32_C(0xff15)
        /* Experimental */
        #define HWRM_DBG_CFG                              UINT32_C(0xff16)
        /* Experimental */
        #define HWRM_DBG_COREDUMP_LIST                    UINT32_C(0xff17)
        /* Experimental */
        #define HWRM_DBG_COREDUMP_INITIATE                UINT32_C(0xff18)
        /* Experimental */
        #define HWRM_DBG_COREDUMP_RETRIEVE                UINT32_C(0xff19)
        /*  */
        #define HWRM_DBG_I2C_CMD                          UINT32_C(0xff1b)
        /* Experimental */
        #define HWRM_NVM_FACTORY_DEFAULTS                 UINT32_C(0xffee)
        #define HWRM_NVM_VALIDATE_OPTION                  UINT32_C(0xffef)
        #define HWRM_NVM_FLUSH                            UINT32_C(0xfff0)
        #define HWRM_NVM_GET_VARIABLE                     UINT32_C(0xfff1)
        #define HWRM_NVM_SET_VARIABLE                     UINT32_C(0xfff2)
        #define HWRM_NVM_INSTALL_UPDATE                   UINT32_C(0xfff3)
        #define HWRM_NVM_MODIFY                           UINT32_C(0xfff4)
        #define HWRM_NVM_VERIFY_UPDATE                    UINT32_C(0xfff5)
        #define HWRM_NVM_GET_DEV_INFO                     UINT32_C(0xfff6)
        #define HWRM_NVM_ERASE_DIR_ENTRY                  UINT32_C(0xfff7)
        #define HWRM_NVM_MOD_DIR_ENTRY                    UINT32_C(0xfff8)
        #define HWRM_NVM_FIND_DIR_ENTRY                   UINT32_C(0xfff9)
        #define HWRM_NVM_GET_DIR_ENTRIES                  UINT32_C(0xfffa)
        #define HWRM_NVM_GET_DIR_INFO                     UINT32_C(0xfffb)
        #define HWRM_NVM_RAW_DUMP                         UINT32_C(0xfffc)
        #define HWRM_NVM_READ                             UINT32_C(0xfffd)
        #define HWRM_NVM_WRITE                            UINT32_C(0xfffe)
        #define HWRM_NVM_RAW_WRITE_BLK                    UINT32_C(0xffff)
        #define HWRM_LAST                                HWRM_NVM_RAW_WRITE_BLK
        uint16_t        unused_0[3];
} __attribute__((packed));

/* Return Codes */
/* ret_codes (size:64b/8B) */
struct ret_codes {
        uint16_t        error_code;
        /* Request was successfully executed by the HWRM. */
        #define HWRM_ERR_CODE_SUCCESS                UINT32_C(0x0)
        /* The HWRM failed to execute the request. */
        #define HWRM_ERR_CODE_FAIL                   UINT32_C(0x1)
        /*
         * The request contains invalid argument(s) or input
         * parameters.
         */
        #define HWRM_ERR_CODE_INVALID_PARAMS         UINT32_C(0x2)
        /*
         * The requester is not allowed to access the requested
         * resource. This error code shall be provided in a
         * response to a request to query or modify an existing
         * resource that is not accessible by the requester.
         */
        #define HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED UINT32_C(0x3)
        /*
         * The HWRM is unable to allocate the requested resource.
         * This code only applies to requests for HWRM resource
         * allocations.
         */
        #define HWRM_ERR_CODE_RESOURCE_ALLOC_ERROR   UINT32_C(0x4)
        /*
         * Invalid combination of flags is specified in the
         * request.
         */
        #define HWRM_ERR_CODE_INVALID_FLAGS          UINT32_C(0x5)
        /*
         * Invalid combination of enables fields is specified in
         * the request.
         */
        #define HWRM_ERR_CODE_INVALID_ENABLES        UINT32_C(0x6)
        /*
         * Request contains a required TLV that is not supported by
         * the installed version of firmware.
         */
        #define HWRM_ERR_CODE_UNSUPPORTED_TLV        UINT32_C(0x7)
        /*
         * No firmware buffer available to accept the request. Driver
         * should retry the request.
         */
        #define HWRM_ERR_CODE_NO_BUFFER              UINT32_C(0x8)
        /*
         * Generic HWRM execution error that represents an
         * internal error.
         */
        #define HWRM_ERR_CODE_HWRM_ERROR             UINT32_C(0xf)
        /* Unknown error */
        #define HWRM_ERR_CODE_UNKNOWN_ERR            UINT32_C(0xfffe)
        /* Unsupported or invalid command */
        #define HWRM_ERR_CODE_CMD_NOT_SUPPORTED      UINT32_C(0xffff)
        #define HWRM_ERR_CODE_LAST \
                HWRM_ERR_CODE_CMD_NOT_SUPPORTED
        uint16_t        unused_0[3];
} __attribute__((packed));

/* Output */
/* hwrm_err_output (size:128b/16B) */
struct hwrm_err_output {
        /*
         * Pass/Fail or error type
         *
         * Note: receiver to verify the in parameters, and fail the call
         * with an error when appropriate
         */
        uint16_t        error_code;
        /* This field returns the type of original request. */
        uint16_t        req_type;
        /* This field provides original sequence number of the command. */
        uint16_t        seq_id;
        /*
         * This field is the length of the response in bytes.  The
         * last byte of the response is a valid flag that will read
         * as '1' when the command has been completely written to
         * memory.
         */
        uint16_t        resp_len;
        /* debug info for this error response. */
        uint32_t        opaque_0;
        /* debug info for this error response. */
        uint16_t        opaque_1;
        /*
         * In the case of an error response, command specific error
         * code is returned in this field.
         */
        uint8_t cmd_err;
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));
/*
 * Following is the signature for HWRM message field that indicates not
 * applicable (All F's). Need to cast it the size of the field if needed.
 */
#define HWRM_NA_SIGNATURE ((uint32_t)(-1))
/* hwrm_func_buf_rgtr */
#define HWRM_MAX_REQ_LEN 128
/* hwrm_selftest_qlist */
#define HWRM_MAX_RESP_LEN 280
/* 7 bit indirection table index. */
#define HW_HASH_INDEX_SIZE 0x80
#define HW_HASH_KEY_SIZE 40
/* valid key for HWRM response */
#define HWRM_RESP_VALID_KEY 1
#define HWRM_VERSION_MAJOR 1
#define HWRM_VERSION_MINOR 9
#define HWRM_VERSION_UPDATE 2
/* non-zero means beta version */
#define HWRM_VERSION_RSVD 9
#define HWRM_VERSION_STR "1.9.2.9"

/****************
 * hwrm_ver_get *
 ****************/


/* hwrm_ver_get_input (size:192b/24B) */
struct hwrm_ver_get_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This field represents the major version of HWRM interface
         * specification supported by the driver HWRM implementation.
         * The interface major version is intended to change only when
         * non backward compatible changes are made to the HWRM
         * interface specification.
         */
        uint8_t hwrm_intf_maj;
        /*
         * This field represents the minor version of HWRM interface
         * specification supported by the driver HWRM implementation.
         * A change in interface minor version is used to reflect
         * significant backward compatible modification to HWRM
         * interface specification.
         * This can be due to addition or removal of functionality.
         * HWRM interface specifications with the same major version
         * but different minor versions are compatible.
         */
        uint8_t hwrm_intf_min;
        /*
         * This field represents the update version of HWRM interface
         * specification supported by the driver HWRM implementation.
         * The interface update version is used to reflect minor
         * changes or bug fixes to a released HWRM interface
         * specification.
         */
        uint8_t hwrm_intf_upd;
        uint8_t unused_0[5];
} __attribute__((packed));

/* hwrm_ver_get_output (size:1408b/176B) */
struct hwrm_ver_get_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This field represents the major version of HWRM interface
         * specification supported by the HWRM implementation.
         * The interface major version is intended to change only when
         * non backward compatible changes are made to the HWRM
         * interface specification.
         * A HWRM implementation that is compliant with this
         * specification shall provide value of 1 in this field.
         */
        uint8_t hwrm_intf_maj_8b;
        /*
         * This field represents the minor version of HWRM interface
         * specification supported by the HWRM implementation.
         * A change in interface minor version is used to reflect
         * significant backward compatible modification to HWRM
         * interface specification.
         * This can be due to addition or removal of functionality.
         * HWRM interface specifications with the same major version
         * but different minor versions are compatible.
         * A HWRM implementation that is compliant with this
         * specification shall provide value of 2 in this field.
         */
        uint8_t hwrm_intf_min_8b;
        /*
         * This field represents the update version of HWRM interface
         * specification supported by the HWRM implementation.
         * The interface update version is used to reflect minor
         * changes or bug fixes to a released HWRM interface
         * specification.
         * A HWRM implementation that is compliant with this
         * specification shall provide value of 2 in this field.
         */
        uint8_t hwrm_intf_upd_8b;
        uint8_t hwrm_intf_rsvd_8b;
        /*
         * This field represents the major version of HWRM firmware.
         * A change in firmware major version represents a major
         * firmware release.
         */
        uint8_t hwrm_fw_maj_8b;
        /*
         * This field represents the minor version of HWRM firmware.
         * A change in firmware minor version represents significant
         * firmware functionality changes.
         */
        uint8_t hwrm_fw_min_8b;
        /*
         * This field represents the build version of HWRM firmware.
         * A change in firmware build version represents bug fixes
         * to a released firmware.
         */
        uint8_t hwrm_fw_bld_8b;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version of the
         * HWRM firmware.
         */
        uint8_t hwrm_fw_rsvd_8b;
        /*
         * This field represents the major version of mgmt firmware.
         * A change in major version represents a major release.
         */
        uint8_t mgmt_fw_maj_8b;
        /*
         * This field represents the minor version of mgmt firmware.
         * A change in minor version represents significant
         * functionality changes.
         */
        uint8_t mgmt_fw_min_8b;
        /*
         * This field represents the build version of mgmt firmware.
         * A change in update version represents bug fixes.
         */
        uint8_t mgmt_fw_bld_8b;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version
         */
        uint8_t mgmt_fw_rsvd_8b;
        /*
         * This field represents the major version of network
         * control firmware.
         * A change in major version represents a major release.
         */
        uint8_t netctrl_fw_maj_8b;
        /*
         * This field represents the minor version of network
         * control firmware.
         * A change in minor version represents significant
         * functionality changes.
         */
        uint8_t netctrl_fw_min_8b;
        /*
         * This field represents the build version of network
         * control firmware.
         * A change in update version represents bug fixes.
         */
        uint8_t netctrl_fw_bld_8b;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version
         */
        uint8_t netctrl_fw_rsvd_8b;
        /*
         * This field is used to indicate device's capabilities and
         * configurations.
         */
        uint32_t        dev_caps_cfg;
        /*
         * If set to 1, then secure firmware update behavior
         * is supported.
         * If set to 0, then secure firmware update behavior is
         * not supported.
         */
        #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SECURE_FW_UPD_SUPPORTED \
                UINT32_C(0x1)
        /*
         * If set to 1, then firmware based DCBX agent is supported.
         * If set to 0, then firmware based DCBX agent capability
         * is not supported on this device.
         */
        #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_FW_DCBX_AGENT_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, then HWRM short command format is supported.
         * If set to 0, then HWRM short command format is not supported.
         */
        #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_SUPPORTED \
                UINT32_C(0x4)
        /*
         * If set to 1, then HWRM short command format is required.
         * If set to 0, then HWRM short command format is not required.
         */
        #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_REQUIRED \
                UINT32_C(0x8)
        /*
         * This field represents the major version of RoCE firmware.
         * A change in major version represents a major release.
         */
        uint8_t roce_fw_maj_8b;
        /*
         * This field represents the minor version of RoCE firmware.
         * A change in minor version represents significant
         * functionality changes.
         */
        uint8_t roce_fw_min_8b;
        /*
         * This field represents the build version of RoCE firmware.
         * A change in update version represents bug fixes.
         */
        uint8_t roce_fw_bld_8b;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version
         */
        uint8_t roce_fw_rsvd_8b;
        /*
         * This field represents the name of HWRM FW (ASCII chars
         * with NULL at the end).
         */
        char    hwrm_fw_name[16];
        /*
         * This field represents the name of mgmt FW (ASCII chars
         * with NULL at the end).
         */
        char    mgmt_fw_name[16];
        /*
         * This field represents the name of network control
         * firmware (ASCII chars with NULL at the end).
         */
        char    netctrl_fw_name[16];
        /*
         * This field is reserved for future use.
         * The responder should set it to 0.
         * The requester should ignore this field.
         */
        uint8_t reserved2[16];
        /*
         * This field represents the name of RoCE FW (ASCII chars
         * with NULL at the end).
         */
        char    roce_fw_name[16];
        /* This field returns the chip number. */
        uint16_t        chip_num;
        /* This field returns the revision of chip. */
        uint8_t chip_rev;
        /* This field returns the chip metal number. */
        uint8_t chip_metal;
        /* This field returns the bond id of the chip. */
        uint8_t chip_bond_id;
        /* This value indicates the type of platform used for chip implementation. */
        uint8_t chip_platform_type;
        /* ASIC */
        #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_ASIC      UINT32_C(0x0)
        /* FPGA platform of the chip. */
        #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_FPGA      UINT32_C(0x1)
        /* Palladium platform of the chip. */
        #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM UINT32_C(0x2)
        #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_LAST \
                HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM
        /*
         * This field returns the maximum value of request window that
         * is supported by the HWRM. The request window is mapped
         * into device address space using MMIO.
         */
        uint16_t        max_req_win_len;
        /*
         * This field returns the maximum value of response buffer in
         * bytes.
         */
        uint16_t        max_resp_len;
        /*
         * This field returns the default request timeout value in
         * milliseconds.
         */
        uint16_t        def_req_timeout;
        /*
         * This field will indicate if any subsystems is not fully
         * initialized.
         */
        uint8_t flags;
        /*
         * If set to 1, device is not ready.
         * If set to 0, device is ready to accept all HWRM commands.
         */
        #define HWRM_VER_GET_OUTPUT_FLAGS_DEV_NOT_RDY       UINT32_C(0x1)
        /*
         * If set to 1, external version present.
         * If set to 0, external version not present.
         */
        #define HWRM_VER_GET_OUTPUT_FLAGS_EXT_VER_AVAIL     UINT32_C(0x2)
        uint8_t unused_0[2];
        /*
         * For backward compatibility this field must be set to 1.
         * Older drivers might look for this field to be 1 before
         * processing the message.
         */
        uint8_t always_1;
        /*
         * This field represents the major version of HWRM interface
         * specification supported by the HWRM implementation.
         * The interface major version is intended to change only when
         * non backward compatible changes are made to the HWRM
         * interface specification. A HWRM implementation that is
         * compliant with this specification shall provide value of 1
         * in this field.
         */
        uint16_t        hwrm_intf_major;
        /*
         * This field represents the minor version of HWRM interface
         * specification supported by the HWRM implementation.
         * A change in interface minor version is used to reflect
         * significant backward compatible modification to HWRM
         * interface specification. This can be due to addition or
         * removal of functionality. HWRM interface specifications
         * with the same major version but different minor versions are
         * compatible. A HWRM implementation that is compliant with
         * this specification shall provide value of 2 in this field.
         */
        uint16_t        hwrm_intf_minor;
        /*
         * This field represents the update version of HWRM interface
         * specification supported by the HWRM implementation. The
         * interface update version is used to reflect minor changes or
         * bug fixes to a released HWRM interface specification.
         * A HWRM implementation that is compliant with this
         * specification shall provide value of 2 in this field.
         */
        uint16_t        hwrm_intf_build;
        /*
         * This field represents the patch version of HWRM interface
         * specification supported by the HWRM implementation.
         */
        uint16_t        hwrm_intf_patch;
        /*
         * This field represents the major version of HWRM firmware.
         * A change in firmware major version represents a major
         * firmware release.
         */
        uint16_t        hwrm_fw_major;
        /*
         * This field represents the minor version of HWRM firmware.
         * A change in firmware minor version represents significant
         * firmware functionality changes.
         */
        uint16_t        hwrm_fw_minor;
        /*
         * This field represents the build version of HWRM firmware.
         * A change in firmware build version represents bug fixes to
         * a released firmware.
         */
        uint16_t        hwrm_fw_build;
        /*
         * This field is a reserved field.
         * This field can be used to represent firmware branches or customer
         * specific releases tied to a specific (major,minor,update) version
         * of the HWRM firmware.
         */
        uint16_t        hwrm_fw_patch;
        /*
         * This field represents the major version of mgmt firmware.
         * A change in major version represents a major release.
         */
        uint16_t        mgmt_fw_major;
        /*
         * This field represents the minor version of HWRM firmware.
         * A change in firmware minor version represents significant
         * firmware functionality changes.
         */
        uint16_t        mgmt_fw_minor;
        /*
         * This field represents the build version of mgmt firmware.
         * A change in update version represents bug fixes.
         */
        uint16_t        mgmt_fw_build;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version.
         */
        uint16_t        mgmt_fw_patch;
        /*
         * This field represents the major version of network control
         * firmware. A change in major version represents
         * a major release.
         */
        uint16_t        netctrl_fw_major;
        /*
         * This field represents the minor version of network control
         * firmware. A change in minor version represents significant
         * functionality changes.
         */
        uint16_t        netctrl_fw_minor;
        /*
         * This field represents the build version of network control
         * firmware. A change in update version represents bug fixes.
         */
        uint16_t        netctrl_fw_build;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version
         */
        uint16_t        netctrl_fw_patch;
        /*
         * This field represents the major version of RoCE firmware.
         * A change in major version represents a major release.
         */
        uint16_t        roce_fw_major;
        /*
         * This field represents the minor version of RoCE firmware.
         * A change in minor version represents significant
         * functionality changes.
         */
        uint16_t        roce_fw_minor;
        /*
         * This field represents the build version of RoCE firmware.
         * A change in update version represents bug fixes.
         */
        uint16_t        roce_fw_build;
        /*
         * This field is a reserved field. This field can be used to
         * represent firmware branches or customer specific releases
         * tied to a specific (major,minor,update) version
         */
        uint16_t        roce_fw_patch;
        /*
         * This field returns the maximum extended request length acceptable
         * by the device which allows requests greater than mailbox size when
         * used with the short cmd request format.
         */
        uint16_t        max_ext_req_len;
        uint8_t unused_1[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* bd_base (size:64b/8B) */
struct bd_base {
        uint8_t type;
        /* This value identifies the type of buffer descriptor. */
        #define BD_BASE_TYPE_MASK       UINT32_C(0x3f)
        #define BD_BASE_TYPE_SFT        0
        /*
         * Indicates that this BD is 16B long and is used for
         * normal L2 packet transmission.
         */
        #define BD_BASE_TYPE_TX_BD_SHORT  UINT32_C(0x0)
        /*
         * Indicates that this BD is 1BB long and is an empty
         * TX BD.  Not valid for use by the driver.
         */
        #define BD_BASE_TYPE_TX_BD_EMPTY  UINT32_C(0x1)
        /*
         * Indicates that this BD is 16B long and is an RX Producer
         * (ie. empty) buffer descriptor.
         */
        #define BD_BASE_TYPE_RX_PROD_PKT  UINT32_C(0x4)
        /*
         * Indicates that this BD is 16B long and is an RX
         * Producer Buffer BD.
         */
        #define BD_BASE_TYPE_RX_PROD_BFR  UINT32_C(0x5)
        /*
         * Indicates that this BD is 16B long and is an
         * RX Producer Assembly Buffer Descriptor.
         */
        #define BD_BASE_TYPE_RX_PROD_AGG  UINT32_C(0x6)
        /*
         * Indicates that this BD is 32B long and is used for
         * normal L2 packet transmission.
         */
        #define BD_BASE_TYPE_TX_BD_LONG   UINT32_C(0x10)
        #define BD_BASE_TYPE_LAST        BD_BASE_TYPE_TX_BD_LONG
        uint8_t unused_1[7];
} __attribute__((packed));

/* tx_bd_short (size:128b/16B) */
struct tx_bd_short {
        /*
         * All bits in this field must be valid on the first BD of a packet.
         * Only the packet_end bit must be valid for the remaining BDs
         * of a packet.
         */
        uint16_t        flags_type;
        /* This value identifies the type of buffer descriptor. */
        #define TX_BD_SHORT_TYPE_MASK            UINT32_C(0x3f)
        #define TX_BD_SHORT_TYPE_SFT             0
        /*
         * Indicates that this BD is 16B long and is used for
         * normal L2 packet transmission.
         */
        #define TX_BD_SHORT_TYPE_TX_BD_SHORT       UINT32_C(0x0)
        #define TX_BD_SHORT_TYPE_LAST             TX_BD_SHORT_TYPE_TX_BD_SHORT
        /*
         * All bits in this field must be valid on the first BD of a packet.
         * Only the packet_end bit must be valid for the remaining BDs
         * of a packet.
         */
        #define TX_BD_SHORT_FLAGS_MASK           UINT32_C(0xffc0)
        #define TX_BD_SHORT_FLAGS_SFT            6
        /*
         * If set to 1, the packet ends with the data in the buffer
         * pointed to by this descriptor.  This flag must be
         * valid on every BD.
         */
        #define TX_BD_SHORT_FLAGS_PACKET_END      UINT32_C(0x40)
        /*
         * If set to 1, the device will not generate a completion for
         * this transmit packet unless there is an error in it's
         * processing.
         * If this bit
         * is set to 0, then the packet will be completed normally.
         *
         * This bit must be valid only on the first BD of a packet.
         */
        #define TX_BD_SHORT_FLAGS_NO_CMPL         UINT32_C(0x80)
        /*
         * This value indicates how many 16B BD locations are consumed
         * in the ring by this packet.
         * A value of 1 indicates that this BD is the only BD (and that
         * the it is a short BD).  A value
         * of 3 indicates either 3 short BDs or 1 long BD and one short
         * BD in the packet.  A value of 0 indicates
         * that there are 32 BD locations in the packet (the maximum).
         *
         * This field is valid only on the first BD of a packet.
         */
        #define TX_BD_SHORT_FLAGS_BD_CNT_MASK     UINT32_C(0x1f00)
        #define TX_BD_SHORT_FLAGS_BD_CNT_SFT      8
        /*
         * This value is a hint for the length of the entire packet.
         * It is used by the chip to optimize internal processing.
         *
         * The packet will be dropped if the hint is too short.
         *
         * This field is valid only on the first BD of a packet.
         */
        #define TX_BD_SHORT_FLAGS_LHINT_MASK      UINT32_C(0x6000)
        #define TX_BD_SHORT_FLAGS_LHINT_SFT       13
        /* indicates packet length < 512B */
        #define TX_BD_SHORT_FLAGS_LHINT_LT512       (UINT32_C(0x0) << 13)
        /* indicates 512 <= packet length < 1KB */
        #define TX_BD_SHORT_FLAGS_LHINT_LT1K        (UINT32_C(0x1) << 13)
        /* indicates 1KB <= packet length < 2KB */
        #define TX_BD_SHORT_FLAGS_LHINT_LT2K        (UINT32_C(0x2) << 13)
        /* indicates packet length >= 2KB */
        #define TX_BD_SHORT_FLAGS_LHINT_GTE2K       (UINT32_C(0x3) << 13)
        #define TX_BD_SHORT_FLAGS_LHINT_LAST \
                TX_BD_SHORT_FLAGS_LHINT_GTE2K
        /*
         * If set to 1, the device immediately updates the Send Consumer
         * Index after the buffer associated with this descriptor has
         * been transferred via DMA to NIC memory from host memory. An
         * interrupt may or may not be generated according to the state
         * of the interrupt avoidance mechanisms. If this bit
         * is set to 0, then the Consumer Index is only updated as soon
         * as one of the host interrupt coalescing conditions has been met.
         *
         * This bit must be valid on the first BD of a packet.
         */
        #define TX_BD_SHORT_FLAGS_COAL_NOW        UINT32_C(0x8000)
        /*
         * This is the length of the host physical buffer this BD describes
         * in bytes.
         *
         * This field must be valid on all BDs of a packet.
         */
        uint16_t        len;
        /*
         * The opaque data field is pass through to the completion and can be
         * used for any data that the driver wants to associate with the
         * transmit BD.
         *
         * This field must be valid on the first BD of a packet.
         */
        uint32_t        opaque;
        /*
         * This is the host physical address for the portion of the packet
         * described by this TX BD.
         *
         * This value must be valid on all BDs of a packet.
         */
        uint64_t        address;
} __attribute__((packed));

/* tx_bd_long (size:128b/16B) */
struct tx_bd_long {
        /* This value identifies the type of buffer descriptor. */
        uint16_t        flags_type;
        /*
         * This value indicates the type of buffer descriptor.
         * packet.
         */
        #define TX_BD_LONG_TYPE_MASK            UINT32_C(0x3f)
        #define TX_BD_LONG_TYPE_SFT             0
        /*
         * Indicates that this BD is 32B long and is used for
         * normal L2 packet transmission.
         */
        #define TX_BD_LONG_TYPE_TX_BD_LONG        UINT32_C(0x10)
        #define TX_BD_LONG_TYPE_LAST             TX_BD_LONG_TYPE_TX_BD_LONG
        /*
         * All bits in this field must be valid on the first BD of a packet.
         * Only the packet_end bit must be valid for the remaining BDs
         * of a packet.
         */
        #define TX_BD_LONG_FLAGS_MASK           UINT32_C(0xffc0)
        #define TX_BD_LONG_FLAGS_SFT            6
        /*
         * If set to 1, the packet ends with the data in the buffer
         * pointed to by this descriptor.  This flag must be
         * valid on every BD.
         */
        #define TX_BD_LONG_FLAGS_PACKET_END      UINT32_C(0x40)
        /*
         * If set to 1, the device will not generate a completion for
         * this transmit packet unless there is an error in it's
         * processing.
         * If this bit
         * is set to 0, then the packet will be completed normally.
         *
         * This bit must be valid only on the first BD of a packet.
         */
        #define TX_BD_LONG_FLAGS_NO_CMPL         UINT32_C(0x80)
        /*
         * This value indicates how many 16B BD locations are consumed
         * in the ring by this packet.
         * A value of 1 indicates that this BD is the only BD (and that
         * the it is a short BD).  A value
         * of 3 indicates either 3 short BDs or 1 long BD and one short
         * BD in the packet.  A value of 0 indicates
         * that there are 32 BD locations in the packet (the maximum).
         *
         * This field is valid only on the first BD of a packet.
         */
        #define TX_BD_LONG_FLAGS_BD_CNT_MASK     UINT32_C(0x1f00)
        #define TX_BD_LONG_FLAGS_BD_CNT_SFT      8
        /*
         * This value is a hint for the length of the entire packet.
         * It is used by the chip to optimize internal processing.
         *
         * The packet will be dropped if the hint is too short.
         *
         * This field is valid only on the first BD of a packet.
         */
        #define TX_BD_LONG_FLAGS_LHINT_MASK      UINT32_C(0x6000)
        #define TX_BD_LONG_FLAGS_LHINT_SFT       13
        /* indicates packet length < 512B */
        #define TX_BD_LONG_FLAGS_LHINT_LT512       (UINT32_C(0x0) << 13)
        /* indicates 512 <= packet length < 1KB */
        #define TX_BD_LONG_FLAGS_LHINT_LT1K        (UINT32_C(0x1) << 13)
        /* indicates 1KB <= packet length < 2KB */
        #define TX_BD_LONG_FLAGS_LHINT_LT2K        (UINT32_C(0x2) << 13)
        /* indicates packet length >= 2KB */
        #define TX_BD_LONG_FLAGS_LHINT_GTE2K       (UINT32_C(0x3) << 13)
        #define TX_BD_LONG_FLAGS_LHINT_LAST       TX_BD_LONG_FLAGS_LHINT_GTE2K
        /*
         * If set to 1, the device immediately updates the Send Consumer
         * Index after the buffer associated with this descriptor has
         * been transferred via DMA to NIC memory from host memory. An
         * interrupt may or may not be generated according to the state
         * of the interrupt avoidance mechanisms. If this bit
         * is set to 0, then the Consumer Index is only updated as soon
         * as one of the host interrupt coalescing conditions has been met.
         *
         * This bit must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_FLAGS_COAL_NOW        UINT32_C(0x8000)
        /*
         * This is the length of the host physical buffer this BD describes
         * in bytes.
         *
         * This field must be valid on all BDs of a packet.
         */
        uint16_t        len;
        /*
         * The opaque data field is pass through to the completion and can be
         * used for any data that the driver wants to associate with the
         * transmit BD.
         *
         * This field must be valid on the first BD of a packet.
         */
        uint32_t        opaque;
        /*
         * This is the host physical address for the portion of the packet
         * described by this TX BD.
         *
         * This value must be valid on all BDs of a packet.
         */
        uint64_t        address;
} __attribute__((packed));

/* tx_bd_long_hi (size:128b/16B) */
struct tx_bd_long_hi {
        /*
         * All bits in this field must be valid on the first BD of a packet.
         * Their value on other BDs of the packet will be ignored.
         */
        uint16_t        lflags;
        /*
         * If set to 1, the controller replaces the TCP/UPD checksum
         * fields of normal TCP/UPD checksum, or the inner TCP/UDP
         * checksum field of the encapsulated TCP/UDP packets with the
         * hardware calculated TCP/UDP checksum for the packet associated
         * with this descriptor. The flag is ignored if the LSO flag is set.
         *
         * This bit must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_LFLAGS_TCP_UDP_CHKSUM     UINT32_C(0x1)
        /*
         * If set to 1,  the controller replaces the IP checksum of the
         * normal packets, or the inner IP checksum of the encapsulated
         * packets with the hardware calculated IP checksum for the
         * packet associated with this descriptor.
         *
         * This bit must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_LFLAGS_IP_CHKSUM          UINT32_C(0x2)
        /*
         * If set to 1, the controller will not append an Ethernet CRC
         * to the end of the frame.
         *
         * This bit must be valid on the first BD of a packet.
         *
         * Packet must be 64B or longer when this flag is set.  It is not
         * useful to use this bit with any form of TX offload such as
         * CSO or LSO.  The intent is that the packet from the host already
         * has a valid Ethernet CRC on the packet.
         */
        #define TX_BD_LONG_LFLAGS_NOCRC              UINT32_C(0x4)
        /*
         * If set to 1, the device will record the time at which the packet
         * was actually transmitted at the TX MAC.
         *
         * This bit must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_LFLAGS_STAMP              UINT32_C(0x8)
        /*
         * If set to 1, The controller replaces the tunnel IP checksum
         * field with hardware calculated IP checksum for the IP header
         * of the packet associated with this descriptor.
         *
         * For outer UDP checksum, global outer UDP checksum TE_NIC register
         * needs to be enabled. If the global outer UDP checksum TE_NIC register
         * bit is set, outer UDP checksum will be calculated for the following
         * cases:
         * 1. Packets with tcp_udp_chksum flag set to offload checksum for inner
         * packet AND the inner packet is TCP/UDP. If the inner packet is ICMP for
         * example (non-TCP/UDP), even if the tcp_udp_chksum is set, the outer UDP
         * checksum will not be calculated.
         * 2. Packets with lso flag set which implies inner TCP checksum calculation
         * as part of LSO operation.
         */
        #define TX_BD_LONG_LFLAGS_T_IP_CHKSUM        UINT32_C(0x10)
        /*
         * If set to 1,  the device will treat this packet with LSO(Large
         * Send Offload) processing for both normal or encapsulated
         * packets, which is a form of TCP segmentation.  When this bit
         * is 1, the hdr_size and mss fields must be valid. The driver
         * doesn't need to set t_ip_chksum, ip_chksum, and tcp_udp_chksum
         * flags since the controller will replace the appropriate
         * checksum fields for segmented packets.
         *
         * When this bit is 1, the hdr_size and mss fields must be valid.
         */
        #define TX_BD_LONG_LFLAGS_LSO                UINT32_C(0x20)
        /*
         * If set to zero when LSO is '1', then the IPID will be treated
         * as a 16b number and will be wrapped if it exceeds a value of
         * 0xffff.
         *
         * If set to one when LSO is '1', then the IPID will be treated
         * as a 15b number and will be wrapped if it exceeds a value 0f
         * 0x7fff.
         */
        #define TX_BD_LONG_LFLAGS_IPID_FMT           UINT32_C(0x40)
        /*
         * If set to zero when LSO is '1', then the IPID of the tunnel
         * IP header will not be modified during LSO operations.
         *
         * If set to one when LSO is '1', then the IPID of the tunnel
         * IP header will be incremented for each subsequent segment of an
         * LSO operation.
         *
         * The flag is ignored if the LSO packet is a normal (non-tunneled)
         * TCP packet.
         */
        #define TX_BD_LONG_LFLAGS_T_IPID             UINT32_C(0x80)
        /*
         * If set to '1', then the RoCE ICRC will be appended to the
         * packet.  Packet must be a valid RoCE format packet.
         */
        #define TX_BD_LONG_LFLAGS_ROCE_CRC           UINT32_C(0x100)
        /*
         * If set to '1', then the FCoE CRC will be appended to the
         * packet.  Packet must be a valid FCoE format packet.
         */
        #define TX_BD_LONG_LFLAGS_FCOE_CRC           UINT32_C(0x200)
        uint16_t        hdr_size;
        /*
         * When LSO is '1', this field must contain the offset of the
         * TCP payload from the beginning of the packet in as
         * 16b words. In case of encapsulated/tunneling packet, this  field
         * contains the offset of the inner TCP payload from beginning of the
         * packet as 16-bit words.
         *
         * This value must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_HDR_SIZE_MASK UINT32_C(0x1ff)
        #define TX_BD_LONG_HDR_SIZE_SFT 0
        uint32_t        mss;
        /*
         * This is the MSS value that will be used to do the LSO processing.
         * The value is the length in bytes of the TCP payload for each
         * segment generated by the LSO operation.
         *
         * This value must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_MSS_MASK UINT32_C(0x7fff)
        #define TX_BD_LONG_MSS_SFT 0
        uint16_t        unused2;
        /*
         * This value selects a CFA action to perform on the packet.
         * Set this value to zero if no CFA action is desired.
         *
         * This value must be valid on the first BD of a packet.
         */
        uint16_t        cfa_action;
        /*
         * This value is action meta-data that defines CFA edit operations
         * that are done in addition to any action editing.
         */
        uint32_t        cfa_meta;
        /* When key=1, This is the VLAN tag VID value. */
        #define TX_BD_LONG_CFA_META_VLAN_VID_MASK     UINT32_C(0xfff)
        #define TX_BD_LONG_CFA_META_VLAN_VID_SFT      0
        /* When key=1, This is the VLAN tag DE value. */
        #define TX_BD_LONG_CFA_META_VLAN_DE           UINT32_C(0x1000)
        /* When key=1, This is the VLAN tag PRI value. */
        #define TX_BD_LONG_CFA_META_VLAN_PRI_MASK     UINT32_C(0xe000)
        #define TX_BD_LONG_CFA_META_VLAN_PRI_SFT      13
        /* When key=1, This is the VLAN tag TPID select value. */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_MASK    UINT32_C(0x70000)
        #define TX_BD_LONG_CFA_META_VLAN_TPID_SFT     16
        /* 0x88a8 */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID88A8  (UINT32_C(0x0) << 16)
        /* 0x8100 */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID8100  (UINT32_C(0x1) << 16)
        /* 0x9100 */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9100  (UINT32_C(0x2) << 16)
        /* 0x9200 */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9200  (UINT32_C(0x3) << 16)
        /* 0x9300 */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_TPID9300  (UINT32_C(0x4) << 16)
        /* Value programmed in CFA VLANTPID register. */
        #define TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG   (UINT32_C(0x5) << 16)
        #define TX_BD_LONG_CFA_META_VLAN_TPID_LAST \
                TX_BD_LONG_CFA_META_VLAN_TPID_TPIDCFG
        /* When key=1, This is the VLAN tag TPID select value. */
        #define TX_BD_LONG_CFA_META_VLAN_RESERVED_MASK UINT32_C(0xff80000)
        #define TX_BD_LONG_CFA_META_VLAN_RESERVED_SFT 19
        /*
         * This field identifies the type of edit to be performed
         * on the packet.
         *
         * This value must be valid on the first BD of a packet.
         */
        #define TX_BD_LONG_CFA_META_KEY_MASK          UINT32_C(0xf0000000)
        #define TX_BD_LONG_CFA_META_KEY_SFT           28
        /* No editing */
        #define TX_BD_LONG_CFA_META_KEY_NONE            (UINT32_C(0x0) << 28)
        /*
         * - meta[17:16] - TPID select value (0 = 0x8100).
         * - meta[15:12] - PRI/DE value.
         * - meta[11:0] - VID value.
         */
        #define TX_BD_LONG_CFA_META_KEY_VLAN_TAG        (UINT32_C(0x1) << 28)
        #define TX_BD_LONG_CFA_META_KEY_LAST \
                TX_BD_LONG_CFA_META_KEY_VLAN_TAG
} __attribute__((packed));

/* tx_bd_empty (size:128b/16B) */
struct tx_bd_empty {
        /* This value identifies the type of buffer descriptor. */
        uint8_t type;
        #define TX_BD_EMPTY_TYPE_MASK       UINT32_C(0x3f)
        #define TX_BD_EMPTY_TYPE_SFT        0
        /*
         * Indicates that this BD is 1BB long and is an empty
         * TX BD.  Not valid for use by the driver.
         */
        #define TX_BD_EMPTY_TYPE_TX_BD_EMPTY  UINT32_C(0x1)
        #define TX_BD_EMPTY_TYPE_LAST        TX_BD_EMPTY_TYPE_TX_BD_EMPTY
        uint8_t unused_1[3];
        uint8_t unused_2;
        uint8_t unused_3[3];
        uint8_t unused_4[8];
} __attribute__((packed));

/* rx_prod_pkt_bd (size:128b/16B) */
struct rx_prod_pkt_bd {
        /* This value identifies the type of buffer descriptor. */
        uint16_t        flags_type;
        /* This value identifies the type of buffer descriptor. */
        #define RX_PROD_PKT_BD_TYPE_MASK         UINT32_C(0x3f)
        #define RX_PROD_PKT_BD_TYPE_SFT          0
        /*
         * Indicates that this BD is 16B long and is an RX Producer
         * (ie. empty) buffer descriptor.
         */
        #define RX_PROD_PKT_BD_TYPE_RX_PROD_PKT    UINT32_C(0x4)
        #define RX_PROD_PKT_BD_TYPE_LAST \
                RX_PROD_PKT_BD_TYPE_RX_PROD_PKT
        #define RX_PROD_PKT_BD_FLAGS_MASK        UINT32_C(0xffc0)
        #define RX_PROD_PKT_BD_FLAGS_SFT         6
        /*
         * If set to 1, the packet will be placed at the address plus
         * 2B.  The 2 Bytes of padding will be written as zero.
         */
        #define RX_PROD_PKT_BD_FLAGS_SOP_PAD      UINT32_C(0x40)
        /*
         * If set to 1, the packet write will be padded out to the
         * nearest cache-line with zero value padding.
         */
        #define RX_PROD_PKT_BD_FLAGS_EOP_PAD      UINT32_C(0x80)
        /*
         * This value is the number of additional buffers in the ring that
         * describe the buffer space to be consumed for the this packet.
         * If the value is zero, then the packet must fit within the
         * space described by this BD.  If this value is 1 or more, it
         * indicates how many additional "buffer" BDs are in the ring
         * immediately following this BD to be used for the same
         * network packet.
         *
         * Even if the packet to be placed does not need all the
         * additional buffers, they will be consumed anyway.
         */
        #define RX_PROD_PKT_BD_FLAGS_BUFFERS_MASK UINT32_C(0x300)
        #define RX_PROD_PKT_BD_FLAGS_BUFFERS_SFT  8
        /*
         * This is the length in Bytes of the host physical buffer where
         * data for the packet may be placed in host memory.
         */
        uint16_t        len;
        /*
         * The opaque data field is pass through to the completion and can be
         * used for any data that the driver wants to associate with this
         * receive buffer set.
         */
        uint32_t        opaque;
        /*
         * This is the host physical address where data for the packet may
         * by placed in host memory.
         */
        uint64_t        address;
} __attribute__((packed));

/* rx_prod_bfr_bd (size:128b/16B) */
struct rx_prod_bfr_bd {
        /* This value identifies the type of buffer descriptor. */
        uint16_t        flags_type;
        /* This value identifies the type of buffer descriptor. */
        #define RX_PROD_BFR_BD_TYPE_MASK       UINT32_C(0x3f)
        #define RX_PROD_BFR_BD_TYPE_SFT        0
        /*
         * Indicates that this BD is 16B long and is an RX
         * Producer Buffer BD.
         */
        #define RX_PROD_BFR_BD_TYPE_RX_PROD_BFR  UINT32_C(0x5)
        #define RX_PROD_BFR_BD_TYPE_LAST        RX_PROD_BFR_BD_TYPE_RX_PROD_BFR
        #define RX_PROD_BFR_BD_FLAGS_MASK      UINT32_C(0xffc0)
        #define RX_PROD_BFR_BD_FLAGS_SFT       6
        /*
         * This is the length in Bytes of the host physical buffer where
         * data for the packet may be placed in host memory.
         */
        uint16_t        len;
        /* This field is not used. */
        uint32_t        opaque;
        /*
         * This is the host physical address where data for the packet may
         * by placed in host memory.
         */
        uint64_t        address;
} __attribute__((packed));

/* rx_prod_agg_bd (size:128b/16B) */
struct rx_prod_agg_bd {
        /* This value identifies the type of buffer descriptor. */
        uint16_t        flags_type;
        /* This value identifies the type of buffer descriptor. */
        #define RX_PROD_AGG_BD_TYPE_MASK         UINT32_C(0x3f)
        #define RX_PROD_AGG_BD_TYPE_SFT          0
        /*
         * Indicates that this BD is 16B long and is an
         * RX Producer Assembly Buffer Descriptor.
         */
        #define RX_PROD_AGG_BD_TYPE_RX_PROD_AGG    UINT32_C(0x6)
        #define RX_PROD_AGG_BD_TYPE_LAST \
                RX_PROD_AGG_BD_TYPE_RX_PROD_AGG
        #define RX_PROD_AGG_BD_FLAGS_MASK        UINT32_C(0xffc0)
        #define RX_PROD_AGG_BD_FLAGS_SFT         6
        /*
         * If set to 1, the packet write will be padded out to the
         * nearest cache-line with zero value padding.
         */
        #define RX_PROD_AGG_BD_FLAGS_EOP_PAD      UINT32_C(0x40)
        /*
         * This is the length in Bytes of the host physical buffer where
         * data for the packet may be placed in host memory.
         */
        uint16_t        len;
        /*
         * The opaque data field is pass through to the completion and can be
         * used for any data that the driver wants to associate with this
         * receive assembly buffer.
         */
        uint32_t        opaque;
        /*
         * This is the host physical address where data for the packet may
         * by placed in host memory.
         */
        uint64_t        address;
} __attribute__((packed));

/* cmpl_base (size:128b/16B) */
struct cmpl_base {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define CMPL_BASE_TYPE_MASK            UINT32_C(0x3f)
        #define CMPL_BASE_TYPE_SFT             0
        /*
         * TX L2 completion:
         *  Completion of TX packet.  Length = 16B
         */
        #define CMPL_BASE_TYPE_TX_L2             UINT32_C(0x0)
        /*
         * RX L2 completion:
         * Completion of and L2 RX packet. Length = 32B
         */
        #define CMPL_BASE_TYPE_RX_L2             UINT32_C(0x11)
        /*
         * RX Aggregation Buffer completion :
         * Completion of an L2 aggregation buffer in support of
         * TPA, HDS, or Jumbo packet completion.  Length = 16B
         */
        #define CMPL_BASE_TYPE_RX_AGG            UINT32_C(0x12)
        /*
         * RX L2 TPA Start Completion:
         * Completion at the beginning of a TPA operation.
         * Length = 32B
         */
        #define CMPL_BASE_TYPE_RX_TPA_START      UINT32_C(0x13)
        /*
         * RX L2 TPA End Completion:
         * Completion at the end of a TPA operation.
         * Length = 32B
         */
        #define CMPL_BASE_TYPE_RX_TPA_END        UINT32_C(0x15)
        /*
         * Statistics Ejection Completion:
         * Completion of statistics data ejection buffer.
         * Length = 16B
         */
        #define CMPL_BASE_TYPE_STAT_EJECT        UINT32_C(0x1a)
        /*
         * HWRM Command Completion:
         * Completion of an HWRM command.
         */
        #define CMPL_BASE_TYPE_HWRM_DONE         UINT32_C(0x20)
        /* Forwarded HWRM Request */
        #define CMPL_BASE_TYPE_HWRM_FWD_REQ      UINT32_C(0x22)
        /* Forwarded HWRM Response */
        #define CMPL_BASE_TYPE_HWRM_FWD_RESP     UINT32_C(0x24)
        /* HWRM Asynchronous Event Information */
        #define CMPL_BASE_TYPE_HWRM_ASYNC_EVENT  UINT32_C(0x2e)
        /* CQ Notification */
        #define CMPL_BASE_TYPE_CQ_NOTIFICATION   UINT32_C(0x30)
        /* SRQ Threshold Event */
        #define CMPL_BASE_TYPE_SRQ_EVENT         UINT32_C(0x32)
        /* DBQ Threshold Event */
        #define CMPL_BASE_TYPE_DBQ_EVENT         UINT32_C(0x34)
        /* QP Async Notification */
        #define CMPL_BASE_TYPE_QP_EVENT          UINT32_C(0x38)
        /* Function Async Notification */
        #define CMPL_BASE_TYPE_FUNC_EVENT        UINT32_C(0x3a)
        #define CMPL_BASE_TYPE_LAST             CMPL_BASE_TYPE_FUNC_EVENT
        /* info1 is 16 b */
        uint16_t        info1;
        /* info2 is 32 b */
        uint32_t        info2;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        uint32_t        info3_v;
        #define CMPL_BASE_V         UINT32_C(0x1)
        #define CMPL_BASE_INFO3_MASK UINT32_C(0xfffffffe)
        #define CMPL_BASE_INFO3_SFT 1
        /* info4 is 32 b */
        uint32_t        info4;
} __attribute__((packed));

/* tx_cmpl (size:128b/16B) */
struct tx_cmpl {
        uint16_t        flags_type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define TX_CMPL_TYPE_MASK       UINT32_C(0x3f)
        #define TX_CMPL_TYPE_SFT        0
        /*
         * TX L2 completion:
         *  Completion of TX packet.  Length = 16B
         */
        #define TX_CMPL_TYPE_TX_L2        UINT32_C(0x0)
        #define TX_CMPL_TYPE_LAST        TX_CMPL_TYPE_TX_L2
        #define TX_CMPL_FLAGS_MASK      UINT32_C(0xffc0)
        #define TX_CMPL_FLAGS_SFT       6
        /*
         * When this bit is '1', it indicates a packet that has an
         * error of some type.  Type of error is indicated in
         * error_flags.
         */
        #define TX_CMPL_FLAGS_ERROR      UINT32_C(0x40)
        /*
         * When this bit is '1', it indicates that the packet completed
         * was transmitted using the push acceleration data provided
         * by the driver.  When this bit is '0', it indicates that the
         * packet had not push acceleration data written or was executed
         * as a normal packet even though push data was provided.
         */
        #define TX_CMPL_FLAGS_PUSH       UINT32_C(0x80)
        /* unused1 is 16 b */
        uint16_t        unused_0;
        /*
         * This is a copy of the opaque field from the first TX BD of this
         * transmitted packet.
         */
        uint32_t        opaque;
        uint16_t        errors_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define TX_CMPL_V                              UINT32_C(0x1)
        #define TX_CMPL_ERRORS_MASK                    UINT32_C(0xfffe)
        #define TX_CMPL_ERRORS_SFT                     1
        /*
         * This error indicates that there was some sort of problem
         * with the BDs for the packet.
         */
        #define TX_CMPL_ERRORS_BUFFER_ERROR_MASK        UINT32_C(0xe)
        #define TX_CMPL_ERRORS_BUFFER_ERROR_SFT         1
        /* No error */
        #define TX_CMPL_ERRORS_BUFFER_ERROR_NO_ERROR      (UINT32_C(0x0) << 1)
        /*
         * Bad Format:
         * BDs were not formatted correctly.
         */
        #define TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT       (UINT32_C(0x2) << 1)
        #define TX_CMPL_ERRORS_BUFFER_ERROR_LAST \
                TX_CMPL_ERRORS_BUFFER_ERROR_BAD_FMT
        /*
         * When this bit is '1', it indicates that the length of
         * the packet was zero.  No packet was transmitted.
         */
        #define TX_CMPL_ERRORS_ZERO_LENGTH_PKT          UINT32_C(0x10)
        /*
         * When this bit is '1', it indicates that the packet
         * was longer than the programmed limit in TDI. No
         * packet was transmitted.
         */
        #define TX_CMPL_ERRORS_EXCESSIVE_BD_LENGTH      UINT32_C(0x20)
        /*
         * When this bit is '1', it indicates that one or more of the
         * BDs associated with this packet generated a PCI error.
         * This probably means the address was not valid.
         */
        #define TX_CMPL_ERRORS_DMA_ERROR                UINT32_C(0x40)
        /*
         * When this bit is '1', it indicates that the packet was longer
         * than indicated by the hint.  No packet was transmitted.
         */
        #define TX_CMPL_ERRORS_HINT_TOO_SHORT           UINT32_C(0x80)
        /*
         * When this bit is '1', it indicates that the packet was
         * dropped due to Poison TLP error on one or more of the
         * TLPs in the PXP completion.
         */
        #define TX_CMPL_ERRORS_POISON_TLP_ERROR         UINT32_C(0x100)
        /* unused2 is 16 b */
        uint16_t        unused_1;
        /* unused3 is 32 b */
        uint32_t        unused_2;
} __attribute__((packed));

/* rx_pkt_cmpl (size:128b/16B) */
struct rx_pkt_cmpl {
        uint16_t        flags_type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define RX_PKT_CMPL_TYPE_MASK                   UINT32_C(0x3f)
        #define RX_PKT_CMPL_TYPE_SFT                    0
        /*
         * RX L2 completion:
         * Completion of and L2 RX packet. Length = 32B
         */
        #define RX_PKT_CMPL_TYPE_RX_L2                    UINT32_C(0x11)
        #define RX_PKT_CMPL_TYPE_LAST                    RX_PKT_CMPL_TYPE_RX_L2
        #define RX_PKT_CMPL_FLAGS_MASK                  UINT32_C(0xffc0)
        #define RX_PKT_CMPL_FLAGS_SFT                   6
        /*
         * When this bit is '1', it indicates a packet that has an
         * error of some type.  Type of error is indicated in
         * error_flags.
         */
        #define RX_PKT_CMPL_FLAGS_ERROR                  UINT32_C(0x40)
        /* This field indicates how the packet was placed in the buffer. */
        #define RX_PKT_CMPL_FLAGS_PLACEMENT_MASK         UINT32_C(0x380)
        #define RX_PKT_CMPL_FLAGS_PLACEMENT_SFT          7
        /*
         * Normal:
         * Packet was placed using normal algorithm.
         */
        #define RX_PKT_CMPL_FLAGS_PLACEMENT_NORMAL         (UINT32_C(0x0) << 7)
        /*
         * Jumbo:
         * Packet was placed using jumbo algorithm.
         */
        #define RX_PKT_CMPL_FLAGS_PLACEMENT_JUMBO          (UINT32_C(0x1) << 7)
        /*
         * Header/Data Separation:
         * Packet was placed using Header/Data separation algorithm.
         * The separation location is indicated by the itype field.
         */
        #define RX_PKT_CMPL_FLAGS_PLACEMENT_HDS            (UINT32_C(0x2) << 7)
        #define RX_PKT_CMPL_FLAGS_PLACEMENT_LAST \
                RX_PKT_CMPL_FLAGS_PLACEMENT_HDS
        /* This bit is '1' if the RSS field in this completion is valid. */
        #define RX_PKT_CMPL_FLAGS_RSS_VALID              UINT32_C(0x400)
        /* unused is 1 b */
        #define RX_PKT_CMPL_FLAGS_UNUSED                 UINT32_C(0x800)
        /*
         * This value indicates what the inner packet determined for the
         * packet was.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_MASK             UINT32_C(0xf000)
        #define RX_PKT_CMPL_FLAGS_ITYPE_SFT              12
        /*
         * Not Known:
         * Indicates that the packet type was not known.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_NOT_KNOWN \
                (UINT32_C(0x0) << 12)
        /*
         * IP Packet:
         * Indicates that the packet was an IP packet, but further
         * classification was not possible.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_IP \
                (UINT32_C(0x1) << 12)
        /*
         * TCP Packet:
         * Indicates that the packet was IP and TCP.
         * This indicates that the payload_offset field is valid.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_TCP \
                (UINT32_C(0x2) << 12)
        /*
         * UDP Packet:
         * Indicates that the packet was IP and UDP.
         * This indicates that the payload_offset field is valid.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_UDP \
                (UINT32_C(0x3) << 12)
        /*
         * FCoE Packet:
         * Indicates that the packet was recognized as a FCoE.
         * This also indicates that the payload_offset field is valid.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_FCOE \
                (UINT32_C(0x4) << 12)
        /*
         * RoCE Packet:
         * Indicates that the packet was recognized as a RoCE.
         * This also indicates that the payload_offset field is valid.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_ROCE \
                (UINT32_C(0x5) << 12)
        /*
         * ICMP Packet:
         * Indicates that the packet was recognized as ICMP.
         * This indicates that the payload_offset field is valid.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_ICMP \
                (UINT32_C(0x7) << 12)
        /*
         * PtP packet wo/timestamp:
         * Indicates that the packet was recognized as a PtP
         * packet.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_WO_TIMESTAMP \
                (UINT32_C(0x8) << 12)
        /*
         * PtP packet w/timestamp:
         * Indicates that the packet was recognized as a PtP
         * packet and that a timestamp was taken for the packet.
         */
        #define RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP \
                (UINT32_C(0x9) << 12)
        #define RX_PKT_CMPL_FLAGS_ITYPE_LAST \
                RX_PKT_CMPL_FLAGS_ITYPE_PTP_W_TIMESTAMP
        /*
         * This is the length of the data for the packet stored in the
         * buffer(s) identified by the opaque value.  This includes
         * the packet BD and any associated buffer BDs.  This does not include
         * the the length of any data places in aggregation BDs.
         */
        uint16_t        len;
        /*
         * This is a copy of the opaque field from the RX BD this completion
         * corresponds to.
         */
        uint32_t        opaque;
        uint8_t agg_bufs_v1;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_PKT_CMPL_V1           UINT32_C(0x1)
        /*
         * This value is the number of aggregation buffers that follow this
         * entry in the completion ring that are a part of this packet.
         * If the value is zero, then the packet is completely contained
         * in the buffer space provided for the packet in the RX ring.
         */
        #define RX_PKT_CMPL_AGG_BUFS_MASK UINT32_C(0x3e)
        #define RX_PKT_CMPL_AGG_BUFS_SFT 1
        /* unused1 is 2 b */
        #define RX_PKT_CMPL_UNUSED1_MASK UINT32_C(0xc0)
        #define RX_PKT_CMPL_UNUSED1_SFT  6
        /*
         * This is the RSS hash type for the packet.  The value is packed
         * {tuple_extrac_op[1:0],rss_profile_id[4:0],tuple_extrac_op[2]}.
         *
         * The value of tuple_extrac_op provides the information about
         * what fields the hash was computed on.
         * * 0: The RSS hash was computed over source IP address,
         * destination IP address, source port, and destination port of inner
         * IP and TCP or UDP headers. Note: For non-tunneled packets,
         * the packet headers are considered inner packet headers for the RSS
         * hash computation purpose.
         * * 1: The RSS hash was computed over source IP address and destination
         * IP address of inner IP header. Note: For non-tunneled packets,
         * the packet headers are considered inner packet headers for the RSS
         * hash computation purpose.
         * * 2: The RSS hash was computed over source IP address,
         * destination IP address, source port, and destination port of
         * IP and TCP or UDP headers of outer tunnel headers.
         * Note: For non-tunneled packets, this value is not applicable.
         * * 3: The RSS hash was computed over source IP address and
         * destination IP address of IP header of outer tunnel headers.
         * Note: For non-tunneled packets, this value is not applicable.
         *
         * Note that 4-tuples values listed above are applicable
         * for layer 4 protocols supported and enabled for RSS in the hardware,
         * HWRM firmware, and drivers. For example, if RSS hash is supported and
         * enabled for TCP traffic only, then the values of tuple_extract_op
         * corresponding to 4-tuples are only valid for TCP traffic.
         */
        uint8_t rss_hash_type;
        /*
         * This value indicates the offset in bytes from the beginning of the packet
         * where the inner payload starts.  This value is valid for TCP, UDP,
         * FCoE, and RoCE packets.
         *
         * A value of zero indicates that header is 256B into the packet.
         */
        uint8_t payload_offset;
        /* unused2 is 8 b */
        uint8_t unused1;
        /*
         * This value is the RSS hash value calculated for the packet
         * based on the mode bits and key value in the VNIC.
         */
        uint32_t        rss_hash;
} __attribute__((packed));

/* rx_pkt_cmpl_hi (size:128b/16B) */
struct rx_pkt_cmpl_hi {
        uint32_t        flags2;
        /*
         * This indicates that the ip checksum was calculated for the
         * inner packet and that the ip_cs_error field indicates if there
         * was an error.
         */
        #define RX_PKT_CMPL_FLAGS2_IP_CS_CALC       UINT32_C(0x1)
        /*
         * This indicates that the TCP, UDP or ICMP checksum was
         * calculated for the inner packet and that the l4_cs_error field
         * indicates if there was an error.
         */
        #define RX_PKT_CMPL_FLAGS2_L4_CS_CALC       UINT32_C(0x2)
        /*
         * This indicates that the ip checksum was calculated for the
         * tunnel header and that the t_ip_cs_error field indicates if there
         * was an error.
         */
        #define RX_PKT_CMPL_FLAGS2_T_IP_CS_CALC     UINT32_C(0x4)
        /*
         * This indicates that the UDP checksum was
         * calculated for the tunnel packet and that the t_l4_cs_error field
         * indicates if there was an error.
         */
        #define RX_PKT_CMPL_FLAGS2_T_L4_CS_CALC     UINT32_C(0x8)
        /* This value indicates what format the metadata field is. */
        #define RX_PKT_CMPL_FLAGS2_META_FORMAT_MASK UINT32_C(0xf0)
        #define RX_PKT_CMPL_FLAGS2_META_FORMAT_SFT  4
        /* No metadata informtaion.  Value is zero. */
        #define RX_PKT_CMPL_FLAGS2_META_FORMAT_NONE   (UINT32_C(0x0) << 4)
        /*
         * The metadata field contains the VLAN tag and TPID value.
         * - metadata[11:0] contains the vlan VID value.
         * - metadata[12] contains the vlan DE value.
         * - metadata[15:13] contains the vlan PRI value.
         * - metadata[31:16] contains the vlan TPID value.
         */
        #define RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN   (UINT32_C(0x1) << 4)
        #define RX_PKT_CMPL_FLAGS2_META_FORMAT_LAST \
                RX_PKT_CMPL_FLAGS2_META_FORMAT_VLAN
        /*
         * This field indicates the IP type for the inner-most IP header.
         * A value of '0' indicates IPv4.  A value of '1' indicates IPv6.
         * This value is only valid if itype indicates a packet
         * with an IP header.
         */
        #define RX_PKT_CMPL_FLAGS2_IP_TYPE          UINT32_C(0x100)
        /*
         * This is data from the CFA block as indicated by the meta_format
         * field.
         */
        uint32_t        metadata;
        /* When meta_format=1, this value is the VLAN VID. */
        #define RX_PKT_CMPL_METADATA_VID_MASK UINT32_C(0xfff)
        #define RX_PKT_CMPL_METADATA_VID_SFT  0
        /* When meta_format=1, this value is the VLAN DE. */
        #define RX_PKT_CMPL_METADATA_DE       UINT32_C(0x1000)
        /* When meta_format=1, this value is the VLAN PRI. */
        #define RX_PKT_CMPL_METADATA_PRI_MASK UINT32_C(0xe000)
        #define RX_PKT_CMPL_METADATA_PRI_SFT  13
        /* When meta_format=1, this value is the VLAN TPID. */
        #define RX_PKT_CMPL_METADATA_TPID_MASK UINT32_C(0xffff0000)
        #define RX_PKT_CMPL_METADATA_TPID_SFT 16
        uint16_t        errors_v2;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_PKT_CMPL_V2 \
                UINT32_C(0x1)
        #define RX_PKT_CMPL_ERRORS_MASK \
                UINT32_C(0xfffe)
        #define RX_PKT_CMPL_ERRORS_SFT                               1
        /*
         * This error indicates that there was some sort of problem with
         * the BDs for the packet that was found after part of the
         * packet was already placed.  The packet should be treated as
         * invalid.
         */
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_MASK \
                UINT32_C(0xe)
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_SFT                   1
        /* No buffer error */
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NO_BUFFER \
                (UINT32_C(0x0) << 1)
        /*
         * Did Not Fit:
         * Packet did not fit into packet buffer provided.
         * For regular placement, this means the packet did not fit
         * in the buffer provided.  For HDS and jumbo placement, this
         * means that the packet could not be placed into 7 physical
         * buffers or less.
         */
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_DID_NOT_FIT \
                (UINT32_C(0x1) << 1)
        /*
         * Not On Chip:
         * All BDs needed for the packet were not on-chip when
         * the packet arrived.
         */
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP \
                (UINT32_C(0x2) << 1)
        /*
         * Bad Format:
         * BDs were not formatted correctly.
         */
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT \
                (UINT32_C(0x3) << 1)
        #define RX_PKT_CMPL_ERRORS_BUFFER_ERROR_LAST \
                RX_PKT_CMPL_ERRORS_BUFFER_ERROR_BAD_FORMAT
        /*
         * This indicates that there was an error in the IP header
         * checksum.
         */
        #define RX_PKT_CMPL_ERRORS_IP_CS_ERROR \
                UINT32_C(0x10)
        /*
         * This indicates that there was an error in the TCP, UDP
         * or ICMP checksum.
         */
        #define RX_PKT_CMPL_ERRORS_L4_CS_ERROR \
                UINT32_C(0x20)
        /*
         * This indicates that there was an error in the tunnel
         * IP header checksum.
         */
        #define RX_PKT_CMPL_ERRORS_T_IP_CS_ERROR \
                UINT32_C(0x40)
        /*
         * This indicates that there was an error in the tunnel
         * UDP checksum.
         */
        #define RX_PKT_CMPL_ERRORS_T_L4_CS_ERROR \
                UINT32_C(0x80)
        /*
         * This indicates that there was a CRC error on either an FCoE
         * or RoCE packet.  The itype indicates the packet type.
         */
        #define RX_PKT_CMPL_ERRORS_CRC_ERROR \
                UINT32_C(0x100)
        /*
         * This indicates that there was an error in the tunnel
         * portion of the packet when this
         * field is non-zero.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_MASK \
                UINT32_C(0xe00)
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_SFT                    9
        /*
         * No additional error occurred on the tunnel portion
         * of the packet of the packet does not have a tunnel.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_NO_ERROR \
                (UINT32_C(0x0) << 9)
        /*
         * Indicates that IP header version does not match
         * expectation from L2 Ethertype for IPv4 and IPv6
         * in the tunnel header.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_VERSION \
                (UINT32_C(0x1) << 9)
        /*
         * Indicates that header length is out of range in the
         * tunnel header. Valid for
         * IPv4.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_HDR_LEN \
                (UINT32_C(0x2) << 9)
        /*
         * Indicates that the physical packet is shorter than that
         * claimed by the PPPoE header length for a tunnel PPPoE
         * packet.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_TUNNEL_TOTAL_ERROR \
                (UINT32_C(0x3) << 9)
        /*
         * Indicates that physical packet is shorter than that claimed
         * by the tunnel l3 header length. Valid for IPv4, or IPv6
         * tunnel packet packets.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_IP_TOTAL_ERROR \
                (UINT32_C(0x4) << 9)
        /*
         * Indicates that the physical packet is shorter than that
         * claimed by the tunnel UDP header length for a tunnel
         * UDP packet that is not fragmented.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_UDP_TOTAL_ERROR \
                (UINT32_C(0x5) << 9)
        /*
         * indicates that the IPv4 TTL or IPv6 hop limit check
         * have failed (e.g. TTL = 0) in the tunnel header. Valid
         * for IPv4, and IPv6.
         */
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL \
                (UINT32_C(0x6) << 9)
        #define RX_PKT_CMPL_ERRORS_T_PKT_ERROR_LAST \
                RX_PKT_CMPL_ERRORS_T_PKT_ERROR_T_L3_BAD_TTL
        /*
         * This indicates that there was an error in the inner
         * portion of the packet when this
         * field is non-zero.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_MASK \
                UINT32_C(0xf000)
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_SFT                      12
        /*
         * No additional error occurred on the tunnel portion
         * of the packet of the packet does not have a tunnel.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_NO_ERROR \
                (UINT32_C(0x0) << 12)
        /*
         * Indicates that IP header version does not match
         * expectation from L2 Ethertype for IPv4 and IPv6 or that
         * option other than VFT was parsed on
         * FCoE packet.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_VERSION \
                (UINT32_C(0x1) << 12)
        /*
         * indicates that header length is out of range. Valid for
         * IPv4 and RoCE
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_HDR_LEN \
                (UINT32_C(0x2) << 12)
        /*
         * indicates that the IPv4 TTL or IPv6 hop limit check
         * have failed (e.g. TTL = 0). Valid for IPv4, and IPv6
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L3_BAD_TTL \
                (UINT32_C(0x3) << 12)
        /*
         * Indicates that physical packet is shorter than that
         * claimed by the l3 header length. Valid for IPv4,
         * IPv6 packet or RoCE packets.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_IP_TOTAL_ERROR \
                (UINT32_C(0x4) << 12)
        /*
         * Indicates that the physical packet is shorter than that
         * claimed by the UDP header length for a UDP packet that is
         * not fragmented.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_UDP_TOTAL_ERROR \
                (UINT32_C(0x5) << 12)
        /*
         * Indicates that TCP header length > IP payload. Valid for
         * TCP packets only.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN \
                (UINT32_C(0x6) << 12)
        /* Indicates that TCP header length < 5. Valid for TCP. */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_HDR_LEN_TOO_SMALL \
                (UINT32_C(0x7) << 12)
        /*
         * Indicates that TCP option headers result in a TCP header
         * size that does not match data offset in TCP header. Valid
         * for TCP.
         */
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN \
                (UINT32_C(0x8) << 12)
        #define RX_PKT_CMPL_ERRORS_PKT_ERROR_LAST \
                RX_PKT_CMPL_ERRORS_PKT_ERROR_L4_BAD_OPT_LEN
        /*
         * This field identifies the CFA action rule that was used for this
         * packet.
         */
        uint16_t        cfa_code;
        uint32_t        reorder;
        /*
         * This value holds the reordering sequence number for the packet.
         * If the reordering sequence is not valid, then this value is zero.
         * The reordering domain for the packet is in the bottom 8 to 10b of
         * the rss_hash value.  The bottom 20b of this value contain the
         * ordering domain value for the packet.
         */
        #define RX_PKT_CMPL_REORDER_MASK UINT32_C(0xffffff)
        #define RX_PKT_CMPL_REORDER_SFT 0
} __attribute__((packed));

/* rx_tpa_start_cmpl (size:128b/16B) */
struct rx_tpa_start_cmpl {
        uint16_t        flags_type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define RX_TPA_START_CMPL_TYPE_MASK                UINT32_C(0x3f)
        #define RX_TPA_START_CMPL_TYPE_SFT                 0
        /*
         * RX L2 TPA Start Completion:
         * Completion at the beginning of a TPA operation.
         * Length = 32B
         */
        #define RX_TPA_START_CMPL_TYPE_RX_TPA_START          UINT32_C(0x13)
        #define RX_TPA_START_CMPL_TYPE_LAST \
                RX_TPA_START_CMPL_TYPE_RX_TPA_START
        #define RX_TPA_START_CMPL_FLAGS_MASK               UINT32_C(0xffc0)
        #define RX_TPA_START_CMPL_FLAGS_SFT                6
        /* This bit will always be '0' for TPA start completions. */
        #define RX_TPA_START_CMPL_FLAGS_ERROR               UINT32_C(0x40)
        /* This field indicates how the packet was placed in the buffer. */
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_MASK      UINT32_C(0x380)
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_SFT       7
        /*
         * Jumbo:
         * TPA Packet was placed using jumbo algorithm.  This means
         * that the first buffer will be filled with data before
         * moving to aggregation buffers.  Each aggregation buffer
         * will be filled before moving to the next aggregation
         * buffer.
         */
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_JUMBO \
                (UINT32_C(0x1) << 7)
        /*
         * Header/Data Separation:
         * Packet was placed using Header/Data separation algorithm.
         * The separation location is indicated by the itype field.
         */
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_HDS \
                (UINT32_C(0x2) << 7)
        /*
         * GRO/Jumbo:
         * Packet will be placed using GRO/Jumbo where the first
         * packet is filled with data. Subsequent packets will be
         * placed such that any one packet does not span two
         * aggregation buffers unless it starts at the beginning of
         * an aggregation buffer.
         */
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_JUMBO \
                (UINT32_C(0x5) << 7)
        /*
         * GRO/Header-Data Separation:
         * Packet will be placed using GRO/HDS where the header
         * is in the first packet.
         * Payload of each packet will be
         * placed such that any one packet does not span two
         * aggregation buffers unless it starts at the beginning of
         * an aggregation buffer.
         */
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_HDS \
                (UINT32_C(0x6) << 7)
        #define RX_TPA_START_CMPL_FLAGS_PLACEMENT_LAST \
                RX_TPA_START_CMPL_FLAGS_PLACEMENT_GRO_HDS
        /* This bit is '1' if the RSS field in this completion is valid. */
        #define RX_TPA_START_CMPL_FLAGS_RSS_VALID           UINT32_C(0x400)
        /* unused is 1 b */
        #define RX_TPA_START_CMPL_FLAGS_UNUSED              UINT32_C(0x800)
        /*
         * This value indicates what the inner packet determined for the
         * packet was.
         */
        #define RX_TPA_START_CMPL_FLAGS_ITYPE_MASK          UINT32_C(0xf000)
        #define RX_TPA_START_CMPL_FLAGS_ITYPE_SFT           12
        /*
         * TCP Packet:
         * Indicates that the packet was IP and TCP.
         */
        #define RX_TPA_START_CMPL_FLAGS_ITYPE_TCP \
                (UINT32_C(0x2) << 12)
        #define RX_TPA_START_CMPL_FLAGS_ITYPE_LAST \
                RX_TPA_START_CMPL_FLAGS_ITYPE_TCP
        /*
         * This value indicates the amount of packet data written to the
         * buffer the opaque field in this completion corresponds to.
         */
        uint16_t        len;
        /*
         * This is a copy of the opaque field from the RX BD this completion
         * corresponds to.
         */
        uint32_t        opaque;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        uint8_t v1;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_TPA_START_CMPL_V1 UINT32_C(0x1)
        #define RX_TPA_START_CMPL_LAST RX_TPA_START_CMPL_V1
        /*
         * This is the RSS hash type for the packet.  The value is packed
         * {tuple_extrac_op[1:0],rss_profile_id[4:0],tuple_extrac_op[2]}.
         *
         * The value of tuple_extrac_op provides the information about
         * what fields the hash was computed on.
         * * 0: The RSS hash was computed over source IP address,
         * destination IP address, source port, and destination port of inner
         * IP and TCP or UDP headers. Note: For non-tunneled packets,
         * the packet headers are considered inner packet headers for the RSS
         * hash computation purpose.
         * * 1: The RSS hash was computed over source IP address and destination
         * IP address of inner IP header. Note: For non-tunneled packets,
         * the packet headers are considered inner packet headers for the RSS
         * hash computation purpose.
         * * 2: The RSS hash was computed over source IP address,
         * destination IP address, source port, and destination port of
         * IP and TCP or UDP headers of outer tunnel headers.
         * Note: For non-tunneled packets, this value is not applicable.
         * * 3: The RSS hash was computed over source IP address and
         * destination IP address of IP header of outer tunnel headers.
         * Note: For non-tunneled packets, this value is not applicable.
         *
         * Note that 4-tuples values listed above are applicable
         * for layer 4 protocols supported and enabled for RSS in the hardware,
         * HWRM firmware, and drivers. For example, if RSS hash is supported and
         * enabled for TCP traffic only, then the values of tuple_extract_op
         * corresponding to 4-tuples are only valid for TCP traffic.
         */
        uint8_t rss_hash_type;
        /*
         * This is the aggregation ID that the completion is associated
         * with.  Use this number to correlate the TPA start completion
         * with the TPA end completion.
         */
        uint16_t        agg_id;
        /* unused2 is 9 b */
        #define RX_TPA_START_CMPL_UNUSED2_MASK UINT32_C(0x1ff)
        #define RX_TPA_START_CMPL_UNUSED2_SFT 0
        /*
         * This is the aggregation ID that the completion is associated
         * with.  Use this number to correlate the TPA start completion
         * with the TPA end completion.
         */
        #define RX_TPA_START_CMPL_AGG_ID_MASK UINT32_C(0xfe00)
        #define RX_TPA_START_CMPL_AGG_ID_SFT  9
        /*
         * This value is the RSS hash value calculated for the packet
         * based on the mode bits and key value in the VNIC.
         */
        uint32_t        rss_hash;
} __attribute__((packed));

/* rx_tpa_start_cmpl_hi (size:128b/16B) */
struct rx_tpa_start_cmpl_hi {
        uint32_t        flags2;
        /*
         * This indicates that the ip checksum was calculated for the
         * inner packet and that the sum passed for all segments
         * included in the aggregation.
         */
        #define RX_TPA_START_CMPL_FLAGS2_IP_CS_CALC       UINT32_C(0x1)
        /*
         * This indicates that the TCP, UDP or ICMP checksum was
         * calculated for the inner packet and that the sum passed
         * for all segments included in the aggregation.
         */
        #define RX_TPA_START_CMPL_FLAGS2_L4_CS_CALC       UINT32_C(0x2)
        /*
         * This indicates that the ip checksum was calculated for the
         * tunnel header and that the sum passed for all segments
         * included in the aggregation.
         */
        #define RX_TPA_START_CMPL_FLAGS2_T_IP_CS_CALC     UINT32_C(0x4)
        /*
         * This indicates that the UDP checksum was
         * calculated for the tunnel packet and that the sum passed for
         * all segments included in the aggregation.
         */
        #define RX_TPA_START_CMPL_FLAGS2_T_L4_CS_CALC     UINT32_C(0x8)
        /* This value indicates what format the metadata field is. */
        #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_MASK UINT32_C(0xf0)
        #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_SFT  4
        /* No metadata informtaion.  Value is zero. */
        #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_NONE \
                (UINT32_C(0x0) << 4)
        /*
         * The metadata field contains the VLAN tag and TPID value.
         * - metadata[11:0] contains the vlan VID value.
         * - metadata[12] contains the vlan DE value.
         * - metadata[15:13] contains the vlan PRI value.
         * - metadata[31:16] contains the vlan TPID value.
         */
        #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_VLAN \
                (UINT32_C(0x1) << 4)
        #define RX_TPA_START_CMPL_FLAGS2_META_FORMAT_LAST \
                RX_TPA_START_CMPL_FLAGS2_META_FORMAT_VLAN
        /*
         * This field indicates the IP type for the inner-most IP header.
         * A value of '0' indicates IPv4.  A value of '1' indicates IPv6.
         */
        #define RX_TPA_START_CMPL_FLAGS2_IP_TYPE          UINT32_C(0x100)
        /*
         * This is data from the CFA block as indicated by the meta_format
         * field.
         */
        uint32_t        metadata;
        /* When meta_format=1, this value is the VLAN VID. */
        #define RX_TPA_START_CMPL_METADATA_VID_MASK UINT32_C(0xfff)
        #define RX_TPA_START_CMPL_METADATA_VID_SFT  0
        /* When meta_format=1, this value is the VLAN DE. */
        #define RX_TPA_START_CMPL_METADATA_DE       UINT32_C(0x1000)
        /* When meta_format=1, this value is the VLAN PRI. */
        #define RX_TPA_START_CMPL_METADATA_PRI_MASK UINT32_C(0xe000)
        #define RX_TPA_START_CMPL_METADATA_PRI_SFT  13
        /* When meta_format=1, this value is the VLAN TPID. */
        #define RX_TPA_START_CMPL_METADATA_TPID_MASK UINT32_C(0xffff0000)
        #define RX_TPA_START_CMPL_METADATA_TPID_SFT 16
        uint16_t        v2;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_TPA_START_CMPL_V2     UINT32_C(0x1)
        /*
         * This field identifies the CFA action rule that was used for this
         * packet.
         */
        uint16_t        cfa_code;
        /*
         * This is the size in bytes of the inner most L4 header.
         * This can be subtracted from the payload_offset to determine
         * the start of the inner most L4 header.
         */
        uint32_t        inner_l4_size_inner_l3_offset_inner_l2_offset_outer_l3_offset;
        /*
         * This is the offset from the beginning of the packet in bytes for
         * the outer L3 header.  If there is no outer L3 header, then this
         * value is zero.
         */
        #define RX_TPA_START_CMPL_OUTER_L3_OFFSET_MASK UINT32_C(0x1ff)
        #define RX_TPA_START_CMPL_OUTER_L3_OFFSET_SFT 0
        /*
         * This is the offset from the beginning of the packet in bytes for
         * the inner most L2 header.
         */
        #define RX_TPA_START_CMPL_INNER_L2_OFFSET_MASK UINT32_C(0x3fe00)
        #define RX_TPA_START_CMPL_INNER_L2_OFFSET_SFT 9
        /*
         * This is the offset from the beginning of the packet in bytes for
         * the inner most L3 header.
         */
        #define RX_TPA_START_CMPL_INNER_L3_OFFSET_MASK UINT32_C(0x7fc0000)
        #define RX_TPA_START_CMPL_INNER_L3_OFFSET_SFT 18
        /*
         * This is the size in bytes of the inner most L4 header.
         * This can be subtracted from the payload_offset to determine
         * the start of the inner most L4 header.
         */
        #define RX_TPA_START_CMPL_INNER_L4_SIZE_MASK  UINT32_C(0xf8000000)
        #define RX_TPA_START_CMPL_INNER_L4_SIZE_SFT   27
} __attribute__((packed));

/* rx_tpa_end_cmpl (size:128b/16B) */
struct rx_tpa_end_cmpl {
        uint16_t        flags_type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define RX_TPA_END_CMPL_TYPE_MASK                UINT32_C(0x3f)
        #define RX_TPA_END_CMPL_TYPE_SFT                 0
        /*
         * RX L2 TPA End Completion:
         * Completion at the end of a TPA operation.
         * Length = 32B
         */
        #define RX_TPA_END_CMPL_TYPE_RX_TPA_END            UINT32_C(0x15)
        #define RX_TPA_END_CMPL_TYPE_LAST \
                RX_TPA_END_CMPL_TYPE_RX_TPA_END
        #define RX_TPA_END_CMPL_FLAGS_MASK               UINT32_C(0xffc0)
        #define RX_TPA_END_CMPL_FLAGS_SFT                6
        /*
         * When this bit is '1', it indicates a packet that has an
         * error of some type.  Type of error is indicated in
         * error_flags.
         */
        #define RX_TPA_END_CMPL_FLAGS_ERROR               UINT32_C(0x40)
        /* This field indicates how the packet was placed in the buffer. */
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_MASK      UINT32_C(0x380)
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_SFT       7
        /*
         * Jumbo:
         * TPA Packet was placed using jumbo algorithm.  This means
         * that the first buffer will be filled with data before
         * moving to aggregation buffers.  Each aggregation buffer
         * will be filled before moving to the next aggregation
         * buffer.
         */
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_JUMBO \
                (UINT32_C(0x1) << 7)
        /*
         * Header/Data Separation:
         * Packet was placed using Header/Data separation algorithm.
         * The separation location is indicated by the itype field.
         */
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_HDS \
                (UINT32_C(0x2) << 7)
        /*
         * GRO/Jumbo:
         * Packet will be placed using GRO/Jumbo where the first
         * packet is filled with data. Subsequent packets will be
         * placed such that any one packet does not span two
         * aggregation buffers unless it starts at the beginning of
         * an aggregation buffer.
         */
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_JUMBO \
                (UINT32_C(0x5) << 7)
        /*
         * GRO/Header-Data Separation:
         * Packet will be placed using GRO/HDS where the header
         * is in the first packet.
         * Payload of each packet will be
         * placed such that any one packet does not span two
         * aggregation buffers unless it starts at the beginning of
         * an aggregation buffer.
         */
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_HDS \
                (UINT32_C(0x6) << 7)
        #define RX_TPA_END_CMPL_FLAGS_PLACEMENT_LAST \
                RX_TPA_END_CMPL_FLAGS_PLACEMENT_GRO_HDS
        /* unused is 2 b */
        #define RX_TPA_END_CMPL_FLAGS_UNUSED_MASK         UINT32_C(0xc00)
        #define RX_TPA_END_CMPL_FLAGS_UNUSED_SFT          10
        /*
         * This value indicates what the inner packet determined for the
         * packet was.
         *  - 2 TCP Packet
         *      Indicates that the packet was IP and TCP.  This indicates
         *      that the ip_cs field is valid and that the tcp_udp_cs
         *      field is valid and contains the TCP checksum.
         *      This also indicates that the payload_offset field is valid.
         */
        #define RX_TPA_END_CMPL_FLAGS_ITYPE_MASK          UINT32_C(0xf000)
        #define RX_TPA_END_CMPL_FLAGS_ITYPE_SFT           12
        /*
         * This value is zero for TPA End completions.
         * There is no data in the buffer that corresponds to the opaque
         * value in this completion.
         */
        uint16_t        len;
        /*
         * This is a copy of the opaque field from the RX BD this completion
         * corresponds to.
         */
        uint32_t        opaque;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        uint8_t agg_bufs_v1;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_TPA_END_CMPL_V1           UINT32_C(0x1)
        /*
         * This value is the number of aggregation buffers that follow this
         * entry in the completion ring that are a part of this aggregation
         * packet.
         * If the value is zero, then the packet is completely contained
         * in the buffer space provided in the aggregation start completion.
         */
        #define RX_TPA_END_CMPL_AGG_BUFS_MASK UINT32_C(0x7e)
        #define RX_TPA_END_CMPL_AGG_BUFS_SFT 1
        /* This value is the number of segments in the TPA operation. */
        uint8_t tpa_segs;
        /*
         * This value indicates the offset in bytes from the beginning of the packet
         * where the inner payload starts.  This value is valid for TCP, UDP,
         * FCoE, and RoCE packets.
         *
         * A value of zero indicates an offset of 256 bytes.
         */
        uint8_t payload_offset;
        uint8_t agg_id;
        /* unused2 is 1 b */
        #define RX_TPA_END_CMPL_UNUSED2     UINT32_C(0x1)
        /*
         * This is the aggregation ID that the completion is associated
         * with.  Use this number to correlate the TPA start completion
         * with the TPA end completion.
         */
        #define RX_TPA_END_CMPL_AGG_ID_MASK UINT32_C(0xfe)
        #define RX_TPA_END_CMPL_AGG_ID_SFT  1
        /*
         * For non-GRO packets, this value is the
         * timestamp delta between earliest and latest timestamp values for
         * TPA packet. If packets were not time stamped, then delta will be
         * zero.
         *
         * For GRO packets, this field is zero except for the following
         * sub-fields.
         * - tsdelta[31]
         *     Timestamp present indication.  When '0', no Timestamp
         *     option is in the packet.  When '1', then a Timestamp
         *     option is present in the packet.
         */
        uint32_t        tsdelta;
} __attribute__((packed));

/* rx_tpa_end_cmpl_hi (size:128b/16B) */
struct rx_tpa_end_cmpl_hi {
        /*
         * This value is the number of duplicate ACKs that have been
         * received as part of the TPA operation.
         */
        uint32_t        tpa_dup_acks;
        /*
         * This value is the number of duplicate ACKs that have been
         * received as part of the TPA operation.
         */
        #define RX_TPA_END_CMPL_TPA_DUP_ACKS_MASK UINT32_C(0xf)
        #define RX_TPA_END_CMPL_TPA_DUP_ACKS_SFT 0
        /*
         * This value is the valid when TPA completion is active.  It
         * indicates the length of the longest segment of the TPA operation
         * for LRO mode and the length of the first segment in GRO mode.
         *
         * This value may be used by GRO software to re-construct the original
         * packet stream from the TPA packet.  This is the length of all
         * but the last segment for GRO.  In LRO mode this value may be used
         * to indicate MSS size to the stack.
         */
        uint16_t        tpa_seg_len;
        /* unused4 is 16 b */
        uint16_t        unused3;
        uint16_t        errors_v2;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_TPA_END_CMPL_V2                             UINT32_C(0x1)
        #define RX_TPA_END_CMPL_ERRORS_MASK                    UINT32_C(0xfffe)
        #define RX_TPA_END_CMPL_ERRORS_SFT                     1
        /*
         * This error indicates that there was some sort of problem with
         * the BDs for the packet that was found after part of the
         * packet was already placed.  The packet should be treated as
         * invalid.
         */
        #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_MASK        UINT32_C(0xe)
        #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_SFT         1
        /*
         * This error occurs when there is a fatal HW problem in
         * the chip only.  It indicates that there were not
         * BDs on chip but that there was adequate reservation.
         * provided by the TPA block.
         */
        #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_NOT_ON_CHIP \
                (UINT32_C(0x2) << 1)
        /*
         * This error occurs when TPA block was not configured to
         * reserve adequate BDs for TPA operations on this RX
         * ring.  All data for the TPA operation was not placed.
         *
         * This error can also be generated when the number of
         * segments is not programmed correctly in TPA and the
         * 33 total aggregation buffers allowed for the TPA
         * operation has been exceeded.
         */
        #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_RSV_ERROR \
                (UINT32_C(0x4) << 1)
        #define RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_LAST \
                RX_TPA_END_CMPL_ERRORS_BUFFER_ERROR_RSV_ERROR
        /* unused5 is 16 b */
        uint16_t        unused_4;
        /*
         * This is the opaque value that was completed for the TPA start
         * completion that corresponds to this TPA end completion.
         */
        uint32_t        start_opaque;
} __attribute__((packed));

/* rx_abuf_cmpl (size:128b/16B) */
struct rx_abuf_cmpl {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define RX_ABUF_CMPL_TYPE_MASK  UINT32_C(0x3f)
        #define RX_ABUF_CMPL_TYPE_SFT   0
        /*
         * RX Aggregation Buffer completion :
         * Completion of an L2 aggregation buffer in support of
         * TPA, HDS, or Jumbo packet completion.  Length = 16B
         */
        #define RX_ABUF_CMPL_TYPE_RX_AGG  UINT32_C(0x12)
        #define RX_ABUF_CMPL_TYPE_LAST   RX_ABUF_CMPL_TYPE_RX_AGG
        /*
         * This is the length of the data for the packet stored in this
         * aggregation buffer identified by the opaque value.  This does not
         * include the length of any
         * data placed in other aggregation BDs or in the packet or buffer
         * BDs.   This length does not include any space added due to
         * hdr_offset register during HDS placement mode.
         */
        uint16_t        len;
        /*
         * This is a copy of the opaque field from the RX BD this aggregation
         * buffer corresponds to.
         */
        uint32_t        opaque;
        uint32_t        v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define RX_ABUF_CMPL_V     UINT32_C(0x1)
        /* unused3 is 32 b */
        uint32_t        unused_2;
} __attribute__((packed));

/* eject_cmpl (size:128b/16B) */
struct eject_cmpl {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define EJECT_CMPL_TYPE_MASK      UINT32_C(0x3f)
        #define EJECT_CMPL_TYPE_SFT       0
        /*
         * Statistics Ejection Completion:
         * Completion of statistics data ejection buffer.
         * Length = 16B
         */
        #define EJECT_CMPL_TYPE_STAT_EJECT  UINT32_C(0x1a)
        #define EJECT_CMPL_TYPE_LAST       EJECT_CMPL_TYPE_STAT_EJECT
        /*
         * This is the length of the statistics data stored in this
         * buffer.
         */
        uint16_t        len;
        /*
         * This is a copy of the opaque field from the RX BD this ejection
         * buffer corresponds to.
         */
        uint32_t        opaque;
        uint32_t        v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define EJECT_CMPL_V     UINT32_C(0x1)
        /* unused3 is 32 b */
        uint32_t        unused_2;
} __attribute__((packed));

/* hwrm_cmpl (size:128b/16B) */
struct hwrm_cmpl {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_CMPL_TYPE_MASK     UINT32_C(0x3f)
        #define HWRM_CMPL_TYPE_SFT      0
        /*
         * HWRM Command Completion:
         * Completion of an HWRM command.
         */
        #define HWRM_CMPL_TYPE_HWRM_DONE  UINT32_C(0x20)
        #define HWRM_CMPL_TYPE_LAST      HWRM_CMPL_TYPE_HWRM_DONE
        /* This is the sequence_id of the HWRM command that has completed. */
        uint16_t        sequence_id;
        /* unused2 is 32 b */
        uint32_t        unused_1;
        uint32_t        v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_CMPL_V     UINT32_C(0x1)
        /* unused4 is 32 b */
        uint32_t        unused_3;
} __attribute__((packed));

/* hwrm_fwd_req_cmpl (size:128b/16B) */
struct hwrm_fwd_req_cmpl {
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        uint16_t        req_len_type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_FWD_REQ_CMPL_TYPE_MASK        UINT32_C(0x3f)
        #define HWRM_FWD_REQ_CMPL_TYPE_SFT         0
        /* Forwarded HWRM Request */
        #define HWRM_FWD_REQ_CMPL_TYPE_HWRM_FWD_REQ  UINT32_C(0x22)
        #define HWRM_FWD_REQ_CMPL_TYPE_LAST \
                HWRM_FWD_REQ_CMPL_TYPE_HWRM_FWD_REQ
        /* Length of forwarded request in bytes. */
        #define HWRM_FWD_REQ_CMPL_REQ_LEN_MASK     UINT32_C(0xffc0)
        #define HWRM_FWD_REQ_CMPL_REQ_LEN_SFT      6
        /*
         * Source ID of this request.
         * Typically used in forwarding requests and responses.
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - HWRM
         */
        uint16_t        source_id;
        /* unused1 is 32 b */
        uint32_t        unused0;
        /* Address of forwarded request. */
        uint32_t        req_buf_addr_v[2];
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_FWD_REQ_CMPL_V                UINT32_C(0x1)
        /* Address of forwarded request. */
        #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_MASK UINT32_C(0xfffffffe)
        #define HWRM_FWD_REQ_CMPL_REQ_BUF_ADDR_SFT 1
} __attribute__((packed));

/* hwrm_fwd_resp_cmpl (size:128b/16B) */
struct hwrm_fwd_resp_cmpl {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_FWD_RESP_CMPL_TYPE_MASK         UINT32_C(0x3f)
        #define HWRM_FWD_RESP_CMPL_TYPE_SFT          0
        /* Forwarded HWRM Response */
        #define HWRM_FWD_RESP_CMPL_TYPE_HWRM_FWD_RESP  UINT32_C(0x24)
        #define HWRM_FWD_RESP_CMPL_TYPE_LAST \
                HWRM_FWD_RESP_CMPL_TYPE_HWRM_FWD_RESP
        /*
         * Source ID of this response.
         * Typically used in forwarding requests and responses.
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - HWRM
         */
        uint16_t        source_id;
        /* Length of forwarded response in bytes. */
        uint16_t        resp_len;
        /* unused2 is 16 b */
        uint16_t        unused_1;
        /* Address of forwarded request. */
        uint32_t        resp_buf_addr_v[2];
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_FWD_RESP_CMPL_V                 UINT32_C(0x1)
        /* Address of forwarded request. */
        #define HWRM_FWD_RESP_CMPL_RESP_BUF_ADDR_MASK UINT32_C(0xfffffffe)
        #define HWRM_FWD_RESP_CMPL_RESP_BUF_ADDR_SFT 1
} __attribute__((packed));

/* hwrm_async_event_cmpl (size:128b/16B) */
struct hwrm_async_event_cmpl {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_TYPE_MASK            UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT  UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Link status changed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_STATUS_CHANGE \
                UINT32_C(0x0)
        /* Link MTU changed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_MTU_CHANGE \
                UINT32_C(0x1)
        /* Link speed changed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CHANGE \
                UINT32_C(0x2)
        /* DCB Configuration changed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DCB_CONFIG_CHANGE \
                UINT32_C(0x3)
        /* Port connection not allowed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_CONN_NOT_ALLOWED \
                UINT32_C(0x4)
        /* Link speed configuration was not allowed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \
                UINT32_C(0x5)
        /* Link speed configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_CHANGE \
                UINT32_C(0x6)
        /* Port PHY configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_PHY_CFG_CHANGE \
                UINT32_C(0x7)
        /* Function driver unloaded */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_UNLOAD \
                UINT32_C(0x10)
        /* Function driver loaded */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_LOAD \
                UINT32_C(0x11)
        /* Function FLR related processing has completed */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_FLR_PROC_CMPLT \
                UINT32_C(0x12)
        /* PF driver unloaded */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_UNLOAD \
                UINT32_C(0x20)
        /* PF driver loaded */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_LOAD \
                UINT32_C(0x21)
        /* VF Function Level Reset (FLR) */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_FLR \
                UINT32_C(0x30)
        /* VF MAC Address Change */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_MAC_ADDR_CHANGE \
                UINT32_C(0x31)
        /* PF-VF communication channel status change. */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \
                UINT32_C(0x32)
        /* VF Configuration Change */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_CFG_CHANGE \
                UINT32_C(0x33)
        /* LLFC/PFC Configuration Change */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LLFC_PFC_CHANGE \
                UINT32_C(0x34)
        /* Default VNIC Configuration Change */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DEFAULT_VNIC_CHANGE \
                UINT32_C(0x35)
        /* HWRM Error */
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR \
                UINT32_C(0xff)
        #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
} __attribute__((packed));

/* hwrm_async_event_cmpl_link_status_change (size:128b/16B) */
struct hwrm_async_event_cmpl_link_status_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Link status changed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_ID_LINK_STATUS_CHANGE \
                UINT32_C(0x0)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_ID_LINK_STATUS_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Indicates link status change */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE \
                UINT32_C(0x1)
        /*
         * If this bit set to 0, then it indicates that the link
         * was up and it went down.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_DOWN \
                UINT32_C(0x0)
        /*
         * If this bit is set to 1, then it indicates that the link
         * was down and it went up.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_UP \
                UINT32_C(0x1)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_LINK_CHANGE_UP
        /* Indicates the physical port this link status change occur */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_MASK \
                UINT32_C(0xe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_SFT \
                1
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff0)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PORT_ID_SFT \
                4
        /* Indicates the physical function this event occured on. */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PF_ID_MASK \
                UINT32_C(0xff00000)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_STATUS_CHANGE_EVENT_DATA1_PF_ID_SFT \
                20
} __attribute__((packed));

/* hwrm_async_event_cmpl_link_mtu_change (size:128b/16B) */
struct hwrm_async_event_cmpl_link_mtu_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Link MTU changed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_ID_LINK_MTU_CHANGE \
                UINT32_C(0x1)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_ID_LINK_MTU_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* The new MTU of the link in bytes. */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_DATA1_NEW_MTU_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_MTU_CHANGE_EVENT_DATA1_NEW_MTU_SFT 0
} __attribute__((packed));

/* hwrm_async_event_cmpl_link_speed_change (size:128b/16B) */
struct hwrm_async_event_cmpl_link_speed_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Link speed changed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_ID_LINK_SPEED_CHANGE \
                UINT32_C(0x2)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_ID_LINK_SPEED_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /*
         * When this bit is '1', the link was forced to the
         * force_link_speed value.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_FORCE \
                UINT32_C(0x1)
        /* The new link speed in 100 Mbps units. */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_MASK \
                UINT32_C(0xfffe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_SFT \
                1
        /* 100Mb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_100MB \
                (UINT32_C(0x1) << 1)
        /* 1Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_1GB \
                (UINT32_C(0xa) << 1)
        /* 2Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_2GB \
                (UINT32_C(0x14) << 1)
        /* 25Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_2_5GB \
                (UINT32_C(0x19) << 1)
        /* 10Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_10GB \
                (UINT32_C(0x64) << 1)
        /* 20Mb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_20GB \
                (UINT32_C(0xc8) << 1)
        /* 25Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_25GB \
                (UINT32_C(0xfa) << 1)
        /* 40Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_40GB \
                (UINT32_C(0x190) << 1)
        /* 50Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_50GB \
                (UINT32_C(0x1f4) << 1)
        /* 100Gb link speed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_100GB \
                (UINT32_C(0x3e8) << 1)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_NEW_LINK_SPEED_100MBPS_100GB
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff0000)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CHANGE_EVENT_DATA1_PORT_ID_SFT \
                16
} __attribute__((packed));

/* hwrm_async_event_cmpl_dcb_config_change (size:128b/16B) */
struct hwrm_async_event_cmpl_dcb_config_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* DCB Configuration changed */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_ID_DCB_CONFIG_CHANGE \
                UINT32_C(0x3)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_ID_DCB_CONFIG_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        /* ETS configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA2_ETS \
                UINT32_C(0x1)
        /* PFC configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA2_PFC \
                UINT32_C(0x2)
        /* APP configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA2_APP \
                UINT32_C(0x4)
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_PORT_ID_SFT \
                0
        /* Priority recommended for RoCE traffic */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_MASK \
                UINT32_C(0xff0000)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_SFT \
                16
        /* none is 255 */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_NONE \
                (UINT32_C(0xff) << 16)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_LAST \
                HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_ROCE_PRIORITY_NONE
        /* Priority recommended for L2 traffic */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_MASK \
                UINT32_C(0xff000000)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_SFT \
                24
        /* none is 255 */
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_NONE \
                (UINT32_C(0xff) << 24)
        #define HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_LAST \
                HWRM_ASYNC_EVENT_CMPL_DCB_CONFIG_CHANGE_EVENT_DATA1_RECOMMEND_L2_PRIORITY_NONE
} __attribute__((packed));

/* hwrm_async_event_cmpl_port_conn_not_allowed (size:128b/16B) */
struct hwrm_async_event_cmpl_port_conn_not_allowed {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Port connection not allowed */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_ID_PORT_CONN_NOT_ALLOWED \
                UINT32_C(0x4)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_ID_PORT_CONN_NOT_ALLOWED
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_PORT_ID_SFT \
                0
        /*
         * This value indicates the current port level enforcement policy
         * for the optics module when there is an optical module mismatch
         * and port is not connected.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_MASK \
                UINT32_C(0xff0000)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_SFT \
                16
        /* No enforcement */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_NONE \
                (UINT32_C(0x0) << 16)
        /* Disable Transmit side Laser. */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_DISABLETX \
                (UINT32_C(0x1) << 16)
        /* Raise a warning message. */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_WARNINGMSG \
                (UINT32_C(0x2) << 16)
        /* Power down the module. */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_PWRDOWN \
                (UINT32_C(0x3) << 16)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_LAST \
                HWRM_ASYNC_EVENT_CMPL_PORT_CONN_NOT_ALLOWED_EVENT_DATA1_ENFORCEMENT_POLICY_PWRDOWN
} __attribute__((packed));

/* hwrm_async_event_cmpl_link_speed_cfg_not_allowed (size:128b/16B) */
struct hwrm_async_event_cmpl_link_speed_cfg_not_allowed {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Link speed configuration was not allowed */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \
                UINT32_C(0x5)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_NOT_ALLOWED_EVENT_DATA1_PORT_ID_SFT \
                0
} __attribute__((packed));

/* hwrm_async_event_cmpl_link_speed_cfg_change (size:128b/16B) */
struct hwrm_async_event_cmpl_link_speed_cfg_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Link speed configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_ID_LINK_SPEED_CFG_CHANGE \
                UINT32_C(0x6)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_ID_LINK_SPEED_CFG_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_PORT_ID_SFT \
                0
        /*
         * If set to 1, it indicates that the supported link speeds
         * configuration on the port has changed.
         * If set to 0, then there is no change in supported link speeds
         * configuration.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_SUPPORTED_LINK_SPEEDS_CHANGE \
                UINT32_C(0x10000)
        /*
         * If set to 1, it indicates that the link speed configuration
         * on the port has become illegal or invalid.
         * If set to 0, then the link speed configuration on the port is
         * legal or valid.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LINK_SPEED_CFG_CHANGE_EVENT_DATA1_ILLEGAL_LINK_SPEED_CFG \
                UINT32_C(0x20000)
} __attribute__((packed));

/* hwrm_async_event_cmpl_port_phy_cfg_change (size:128b/16B) */
struct hwrm_async_event_cmpl_port_phy_cfg_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Port PHY configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_ID_PORT_PHY_CFG_CHANGE \
                UINT32_C(0x7)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_ID_PORT_PHY_CFG_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_PORT_ID_SFT \
                0
        /*
         * If set to 1, it indicates that the FEC
         * configuration on the port has changed.
         * If set to 0, then there is no change in FEC configuration.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_FEC_CFG_CHANGE \
                UINT32_C(0x10000)
        /*
         * If set to 1, it indicates that the EEE configuration
         * on the port has changed.
         * If set to 0, then there is no change in EEE configuration
         * on the port.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_EEE_CFG_CHANGE \
                UINT32_C(0x20000)
        /*
         * If set to 1, it indicates that the pause configuration
         * on the PHY has changed.
         * If set to 0, then there is no change in the pause
         * configuration on the PHY.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PORT_PHY_CFG_CHANGE_EVENT_DATA1_PAUSE_CFG_CHANGE \
                UINT32_C(0x40000)
} __attribute__((packed));

/* hwrm_async_event_cmpl_func_drvr_unload (size:128b/16B) */
struct hwrm_async_event_cmpl_func_drvr_unload {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Function driver unloaded */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_ID_FUNC_DRVR_UNLOAD \
                UINT32_C(0x10)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_ID_FUNC_DRVR_UNLOAD
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Function ID */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_SFT \
                0
} __attribute__((packed));

/* hwrm_async_event_cmpl_func_drvr_load (size:128b/16B) */
struct hwrm_async_event_cmpl_func_drvr_load {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Function driver loaded */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_ID_FUNC_DRVR_LOAD \
                UINT32_C(0x11)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_ID_FUNC_DRVR_LOAD
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Function ID */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_DATA1_FUNC_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_DRVR_LOAD_EVENT_DATA1_FUNC_ID_SFT 0
} __attribute__((packed));

/* hwrm_async_event_cmpl_func_flr_proc_cmplt (size:128b/16B) */
struct hwrm_async_event_cmpl_func_flr_proc_cmplt {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Function FLR related processing has completed */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_ID_FUNC_FLR_PROC_CMPLT \
                UINT32_C(0x12)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_ID_FUNC_FLR_PROC_CMPLT
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Function ID */
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_DATA1_FUNC_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_FUNC_FLR_PROC_CMPLT_EVENT_DATA1_FUNC_ID_SFT \
                0
} __attribute__((packed));

/* hwrm_async_event_cmpl_pf_drvr_unload (size:128b/16B) */
struct hwrm_async_event_cmpl_pf_drvr_unload {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* PF driver unloaded */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_ID_PF_DRVR_UNLOAD \
                UINT32_C(0x20)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_ID_PF_DRVR_UNLOAD
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PF ID */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_FUNC_ID_SFT 0
        /* Indicates the physical port this pf belongs to */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_PORT_MASK \
                UINT32_C(0x70000)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_UNLOAD_EVENT_DATA1_PORT_SFT    16
} __attribute__((packed));

/* hwrm_async_event_cmpl_pf_drvr_load (size:128b/16B) */
struct hwrm_async_event_cmpl_pf_drvr_load {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* PF driver loaded */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_ID_PF_DRVR_LOAD \
                UINT32_C(0x21)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_ID_PF_DRVR_LOAD
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* PF ID */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_FUNC_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_FUNC_ID_SFT 0
        /* Indicates the physical port this pf belongs to */
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_PORT_MASK \
                UINT32_C(0x70000)
        #define HWRM_ASYNC_EVENT_CMPL_PF_DRVR_LOAD_EVENT_DATA1_PORT_SFT    16
} __attribute__((packed));

/* hwrm_async_event_cmpl_vf_flr (size:128b/16B) */
struct hwrm_async_event_cmpl_vf_flr {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_VF_FLR_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* VF Function Level Reset (FLR) */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_ID_VF_FLR UINT32_C(0x30)
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_ID_VF_FLR
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* VF ID */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_DATA1_VF_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_DATA1_VF_ID_SFT 0
        /* Indicates the physical function this event occured on. */
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_DATA1_PF_ID_MASK \
                UINT32_C(0xff0000)
        #define HWRM_ASYNC_EVENT_CMPL_VF_FLR_EVENT_DATA1_PF_ID_SFT 16
} __attribute__((packed));

/* hwrm_async_event_cmpl_vf_mac_addr_change (size:128b/16B) */
struct hwrm_async_event_cmpl_vf_mac_addr_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* VF MAC Address Change */
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_ID_VF_MAC_ADDR_CHANGE \
                UINT32_C(0x31)
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_ID_VF_MAC_ADDR_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* VF ID */
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_DATA1_VF_ID_MASK \
                UINT32_C(0xffff)
        #define HWRM_ASYNC_EVENT_CMPL_VF_MAC_ADDR_CHANGE_EVENT_DATA1_VF_ID_SFT \
                0
} __attribute__((packed));

/* hwrm_async_event_cmpl_pf_vf_comm_status_change (size:128b/16B) */
struct hwrm_async_event_cmpl_pf_vf_comm_status_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* PF-VF communication channel status change. */
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \
                UINT32_C(0x32)
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_EVENT_ID_PF_VF_COMM_STATUS_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /*
         * If this bit is set to 1, then it indicates that the PF-VF
         * communication was lost and it is established.
         * If this bit set to 0, then it indicates that the PF-VF
         * communication was established and it is lost.
         */
        #define HWRM_ASYNC_EVENT_CMPL_PF_VF_COMM_STATUS_CHANGE_EVENT_DATA1_COMM_ESTABLISHED \
                UINT32_C(0x1)
} __attribute__((packed));

/* hwrm_async_event_cmpl_vf_cfg_change (size:128b/16B) */
struct hwrm_async_event_cmpl_vf_cfg_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* VF Configuration Change */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_ID_VF_CFG_CHANGE \
                UINT32_C(0x33)
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_ID_VF_CFG_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /*
         * Each flag provided in this field indicates a specific VF
         * configuration change. At least one of these flags shall be set to 1
         * when an asynchronous event completion of this type is provided
         * by the HWRM.
         */
        uint32_t        event_data1;
        /*
         * If this bit is set to 1, then the value of MTU
         * was changed on this VF.
         * If set to 0, then this bit should be ignored.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_MTU_CHANGE \
                UINT32_C(0x1)
        /*
         * If this bit is set to 1, then the value of MRU
         * was changed on this VF.
         * If set to 0, then this bit should be ignored.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_MRU_CHANGE \
                UINT32_C(0x2)
        /*
         * If this bit is set to 1, then the value of default MAC
         * address was changed on this VF.
         * If set to 0, then this bit should be ignored.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_DFLT_MAC_ADDR_CHANGE \
                UINT32_C(0x4)
        /*
         * If this bit is set to 1, then the value of default VLAN
         * was changed on this VF.
         * If set to 0, then this bit should be ignored.
         */
        #define HWRM_ASYNC_EVENT_CMPL_VF_CFG_CHANGE_EVENT_DATA1_DFLT_VLAN_CHANGE \
                UINT32_C(0x8)
} __attribute__((packed));

/* hwrm_async_event_cmpl_llfc_pfc_change (size:128b/16B) */
struct hwrm_async_event_cmpl_llfc_pfc_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* unused1 is 10 b */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_UNUSED1_MASK \
                UINT32_C(0xffc0)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_UNUSED1_SFT          6
        /* Identifiers of events. */
        uint16_t        event_id;
        /* LLFC/PFC Configuration Change */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_ID_LLFC_PFC_CHANGE \
                UINT32_C(0x34)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_ID_LLFC_PFC_CHANGE
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Indicates llfc pfc status change */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_MASK \
                UINT32_C(0x3)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_SFT \
                0
        /*
         * If this field set to 1, then it indicates that llfc is
         * enabled.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_LLFC \
                UINT32_C(0x1)
        /*
         * If this field is set to 2, then it indicates that pfc
         * is enabled.
         */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_PFC \
                UINT32_C(0x2)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_LAST \
                HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_LLFC_PFC_PFC
        /* Indicates the physical port this llfc pfc change occur */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_MASK \
                UINT32_C(0x1c)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_SFT \
                2
        /* PORT ID */
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_ID_MASK \
                UINT32_C(0x1fffe0)
        #define HWRM_ASYNC_EVENT_CMPL_LLFC_PFC_CHANGE_EVENT_DATA1_PORT_ID_SFT \
                5
} __attribute__((packed));

/* hwrm_async_event_cmpl_default_vnic_change (size:128b/16B) */
struct hwrm_async_event_cmpl_default_vnic_change {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_TYPE_SFT \
                0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_TYPE_HWRM_ASYNC_EVENT
        /* unused1 is 10 b */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_UNUSED1_MASK \
                UINT32_C(0xffc0)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_UNUSED1_SFT \
                6
        /* Identifiers of events. */
        uint16_t        event_id;
        /* Notification of a default vnic allocaiton or free */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_ID_ALLOC_FREE_NOTIFICATION \
                UINT32_C(0x35)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_ID_ALLOC_FREE_NOTIFICATION
        /* Event specific data */
        uint32_t        event_data2;
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_V \
                UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_OPAQUE_MASK \
                UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Indicates default vnic configuration change */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_DEF_VNIC_STATE_MASK \
                UINT32_C(0x3)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_DEF_VNIC_STATE_SFT \
                0
        /*
         * If this field is set to 1, then it indicates that
         * a default VNIC has been allocate.
         */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_DEF_VNIC_STATE_DEF_VNIC_ALLOC \
                UINT32_C(0x1)
        /*
         * If this field is set to 2, then it indicates that
         * a default VNIC has been freed.
         */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_DEF_VNIC_STATE_DEF_VNIC_FREE \
                UINT32_C(0x2)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_DEF_VNIC_STATE_LAST \
                HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_DEF_VNIC_STATE_DEF_VNIC_FREE
        /* Indicates the physical function this event occured on. */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_PF_ID_MASK \
                UINT32_C(0x3fc)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_PF_ID_SFT \
                2
        /* Indicates the virtual function this event occured on */
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_VF_ID_MASK \
                UINT32_C(0x3fffc00)
        #define HWRM_ASYNC_EVENT_CMPL_DEFAULT_VNIC_CHANGE_EVENT_DATA1_VF_ID_SFT \
                10
} __attribute__((packed));

/* hwrm_async_event_cmpl_hwrm_error (size:128b/16B) */
struct hwrm_async_event_cmpl_hwrm_error {
        uint16_t        type;
        /*
         * This field indicates the exact type of the completion.
         * By convention, the LSB identifies the length of the
         * record in 16B units.  Even values indicate 16B
         * records.  Odd values indicate 32B
         * records.
         */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_MASK \
                UINT32_C(0x3f)
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_SFT             0
        /* HWRM Asynchronous Event Information */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_HWRM_ASYNC_EVENT \
                UINT32_C(0x2e)
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_LAST \
                HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_TYPE_HWRM_ASYNC_EVENT
        /* Identifiers of events. */
        uint16_t        event_id;
        /* HWRM Error */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_ID_HWRM_ERROR \
                UINT32_C(0xff)
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_ID_LAST \
                HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_ID_HWRM_ERROR
        /* Event specific data */
        uint32_t        event_data2;
        /* Severity of HWRM Error */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_MASK \
                UINT32_C(0xff)
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_SFT     0
        /* Warning */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_WARNING \
                UINT32_C(0x0)
        /* Non-fatal Error */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_NONFATAL \
                UINT32_C(0x1)
        /* Fatal Error */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_FATAL \
                UINT32_C(0x2)
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_LAST \
                HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA2_SEVERITY_FATAL
        uint8_t opaque_v;
        /*
         * This value is written by the NIC such that it will be different
         * for each pass through the completion queue.   The even passes
         * will write 1.  The odd passes will write 0.
         */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_V          UINT32_C(0x1)
        /* opaque is 7 b */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_OPAQUE_MASK UINT32_C(0xfe)
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_OPAQUE_SFT 1
        /* 8-lsb timestamp from POR (100-msec resolution) */
        uint8_t timestamp_lo;
        /* 16-lsb timestamp from POR (100-msec resolution) */
        uint16_t        timestamp_hi;
        /* Event specific data */
        uint32_t        event_data1;
        /* Time stamp for error event */
        #define HWRM_ASYNC_EVENT_CMPL_HWRM_ERROR_EVENT_DATA1_TIMESTAMP \
                UINT32_C(0x1)
} __attribute__((packed));

/*******************
 * hwrm_func_reset *
 *******************/


/* hwrm_func_reset_input (size:192b/24B) */
struct hwrm_func_reset_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the vf_id_valid field to be
         * configured.
         */
        #define HWRM_FUNC_RESET_INPUT_ENABLES_VF_ID_VALID     UINT32_C(0x1)
        /*
         * The ID of the VF that this PF is trying to reset.
         * Only the parent PF shall be allowed to reset a child VF.
         *
         * A parent PF driver shall use this field only when a specific child VF
         * is requested to be reset.
         */
        uint16_t        vf_id;
        /* This value indicates the level of a function reset. */
        uint8_t func_reset_level;
        /*
         * Reset the caller function and its children VFs (if any). If no
         * children functions exist, then reset the caller function only.
         */
        #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETALL \
                UINT32_C(0x0)
        /* Reset the caller function only */
        #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETME \
                UINT32_C(0x1)
        /*
         * Reset all children VFs of the caller function driver if the
         * caller is a PF driver.
         * It is an error to specify this level by a VF driver.
         * It is an error to specify this level by a PF driver with
         * no children VFs.
         */
        #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETCHILDREN \
                UINT32_C(0x2)
        /*
         * Reset a specific VF of the caller function driver if the caller
         * is the parent PF driver.
         * It is an error to specify this level by a VF driver.
         * It is an error to specify this level by a PF driver that is not
         * the parent of the VF that is being requested to reset.
         */
        #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF \
                UINT32_C(0x3)
        #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_LAST \
                HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF
        uint8_t unused_0;
} __attribute__((packed));

/* hwrm_func_reset_output (size:128b/16B) */
struct hwrm_func_reset_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************
 * hwrm_func_getfid *
 ********************/


/* hwrm_func_getfid_input (size:192b/24B) */
struct hwrm_func_getfid_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the pci_id field to be
         * configured.
         */
        #define HWRM_FUNC_GETFID_INPUT_ENABLES_PCI_ID     UINT32_C(0x1)
        /*
         * This value is the PCI ID of the queried function.
         * If ARI is enabled, then it is
         * Bus Number (8b):Function Number(8b). Otherwise, it is
         * Bus Number (8b):Device Number (5b):Function Number(3b).
         */
        uint16_t        pci_id;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_func_getfid_output (size:128b/16B) */
struct hwrm_func_getfid_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * FID value.  This value is used to identify operations on the PCI
         * bus as belonging to a particular PCI function.
         */
        uint16_t        fid;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_func_vf_alloc *
 **********************/


/* hwrm_func_vf_alloc_input (size:192b/24B) */
struct hwrm_func_vf_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the first_vf_id field to be
         * configured.
         */
        #define HWRM_FUNC_VF_ALLOC_INPUT_ENABLES_FIRST_VF_ID     UINT32_C(0x1)
        /*
         * This value is used to identify a Virtual Function (VF).
         * The scope of VF ID is local within a PF.
         */
        uint16_t        first_vf_id;
        /* The number of virtual functions requested. */
        uint16_t        num_vfs;
} __attribute__((packed));

/* hwrm_func_vf_alloc_output (size:128b/16B) */
struct hwrm_func_vf_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The ID of the first VF allocated. */
        uint16_t        first_vf_id;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_func_vf_free *
 *********************/


/* hwrm_func_vf_free_input (size:192b/24B) */
struct hwrm_func_vf_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the first_vf_id field to be
         * configured.
         */
        #define HWRM_FUNC_VF_FREE_INPUT_ENABLES_FIRST_VF_ID     UINT32_C(0x1)
        /*
         * This value is used to identify a Virtual Function (VF).
         * The scope of VF ID is local within a PF.
         */
        uint16_t        first_vf_id;
        /*
         * The number of virtual functions requested.
         * 0xFFFF - Cleanup all children of this PF.
         */
        uint16_t        num_vfs;
} __attribute__((packed));

/* hwrm_func_vf_free_output (size:128b/16B) */
struct hwrm_func_vf_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************
 * hwrm_func_vf_cfg *
 ********************/


/* hwrm_func_vf_cfg_input (size:448b/56B) */
struct hwrm_func_vf_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the mtu field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_MTU \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the guest_vlan field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_GUEST_VLAN \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the async_event_cr field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_ASYNC_EVENT_CR \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the dflt_mac_addr field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_DFLT_MAC_ADDR \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the num_rsscos_ctxs field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the num_cmpl_rings field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_CMPL_RINGS \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the num_tx_rings field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_TX_RINGS \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the num_rx_rings field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_RX_RINGS \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the num_l2_ctxs field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_L2_CTXS \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the num_vnics field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_VNICS \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the num_stat_ctxs field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_STAT_CTXS \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the num_hw_ring_grps field to be
         * configured.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS \
                UINT32_C(0x800)
        /*
         * The maximum transmission unit requested on the function.
         * The HWRM should make sure that the mtu of
         * the function does not exceed the mtu of the physical
         * port that this function is associated with.
         *
         * In addition to requesting mtu per function, it is
         * possible to configure mtu per transmit ring.
         * By default, the mtu of each transmit ring associated
         * with a function is equal to the mtu of the function.
         * The HWRM should make sure that the mtu of each transmit
         * ring that is assigned to a function has a valid mtu.
         */
        uint16_t        mtu;
        /*
         * The guest VLAN for the function being configured.
         * This field's format is same as 802.1Q Tag's
         * Tag Control Information (TCI) format that includes both
         * Priority Code Point (PCP) and VLAN Identifier (VID).
         */
        uint16_t        guest_vlan;
        /*
         * ID of the target completion ring for receiving asynchronous
         * event completions. If this field is not valid, then the
         * HWRM shall use the default completion ring of the function
         * that is being configured as the target completion ring for
         * providing any asynchronous event completions for that
         * function.
         * If this field is valid, then the HWRM shall use the
         * completion ring identified by this ID as the target
         * completion ring for providing any asynchronous event
         * completions for the function that is being configured.
         */
        uint16_t        async_event_cr;
        /*
         * This value is the current MAC address requested by the VF
         * driver to be configured on this VF. A value of
         * 00-00-00-00-00-00 indicates no MAC address configuration
         * is requested by the VF driver.
         * The parent PF driver may reject or overwrite this
         * MAC address.
         */
        uint8_t dflt_mac_addr[6];
        uint32_t        flags;
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of TX rings) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_TX_ASSETS_TEST \
                UINT32_C(0x1)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of RX rings) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_RX_ASSETS_TEST \
                UINT32_C(0x2)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of CMPL rings) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_CMPL_ASSETS_TEST \
                UINT32_C(0x4)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of RSS ctx) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_RSSCOS_CTX_ASSETS_TEST \
                UINT32_C(0x8)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of ring groups) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_RING_GRP_ASSETS_TEST \
                UINT32_C(0x10)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of stat ctx) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_STAT_CTX_ASSETS_TEST \
                UINT32_C(0x20)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of VNICs) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_VNIC_ASSETS_TEST \
                UINT32_C(0x40)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of L2 ctx) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_VF_CFG_INPUT_FLAGS_L2_CTX_ASSETS_TEST \
                UINT32_C(0x80)
        /* The number of RSS/COS contexts requested for the VF. */
        uint16_t        num_rsscos_ctxs;
        /* The number of completion rings requested for the VF. */
        uint16_t        num_cmpl_rings;
        /* The number of transmit rings requested for the VF. */
        uint16_t        num_tx_rings;
        /* The number of receive rings requested for the VF. */
        uint16_t        num_rx_rings;
        /* The number of L2 contexts requested for the VF. */
        uint16_t        num_l2_ctxs;
        /* The number of vnics requested for the VF. */
        uint16_t        num_vnics;
        /* The number of statistic contexts requested for the VF. */
        uint16_t        num_stat_ctxs;
        /* The number of HW ring groups requested for the VF. */
        uint16_t        num_hw_ring_grps;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_func_vf_cfg_output (size:128b/16B) */
struct hwrm_func_vf_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************
 * hwrm_func_qcaps *
 *******************/


/* hwrm_func_qcaps_input (size:192b/24B) */
struct hwrm_func_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being queried.
         * 0xFF... (All Fs) if the query is for the requesting
         * function.
         */
        uint16_t        fid;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_qcaps_output (size:640b/80B) */
struct hwrm_func_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * FID value.  This value is used to identify operations on the PCI
         * bus as belonging to a particular PCI function.
         */
        uint16_t        fid;
        /*
         * Port ID of port that this function is associated with.
         * Valid only for the PF.
         * 0xFF... (All Fs) if this function is not associated with
         * any port.
         * 0xFF... (All Fs) if this function is called from a VF.
         */
        uint16_t        port_id;
        uint32_t        flags;
        /* If 1, then Push mode is supported on this function. */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED \
                UINT32_C(0x1)
        /*
         * If 1, then the global MSI-X auto-masking is enabled for the
         * device.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING \
                UINT32_C(0x2)
        /*
         * If 1, then the Precision Time Protocol (PTP) processing
         * is supported on this function.
         * The HWRM should enable PTP on only a single Physical
         * Function (PF) per port.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED \
                UINT32_C(0x4)
        /*
         * If 1, then RDMA over Converged Ethernet (RoCE) v1
         * is supported on this function.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V1_SUPPORTED \
                UINT32_C(0x8)
        /*
         * If 1, then RDMA over Converged Ethernet (RoCE) v2
         * is supported on this function.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V2_SUPPORTED \
                UINT32_C(0x10)
        /*
         * If 1, then control and configuration of WoL magic packet
         * are supported on this function.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_MAGICPKT_SUPPORTED \
                UINT32_C(0x20)
        /*
         * If 1, then control and configuration of bitmap pattern
         * packet are supported on this function.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_BMP_SUPPORTED \
                UINT32_C(0x40)
        /*
         * If set to 1, then the control and configuration of rate limit
         * of an allocated TX ring on the queried function is supported.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_RING_RL_SUPPORTED \
                UINT32_C(0x80)
        /*
         * If 1, then control and configuration of minimum and
         * maximum bandwidths are supported on the queried function.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_BW_CFG_SUPPORTED \
                UINT32_C(0x100)
        /*
         * If the query is for a VF, then this flag shall be ignored.
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to set the rate limits
         * on the TX rings of its children VFs.
         * If this query is for a PF and this flag is set to 0, then
         * the PF does not have the capability to set the rate limits
         * on the TX rings of its children VFs.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_TX_RING_RL_SUPPORTED \
                UINT32_C(0x200)
        /*
         * If the query is for a VF, then this flag shall be ignored.
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to set the minimum and/or
         * maximum bandwidths for its children VFs.
         * If this query is for a PF and this flag is set to 0, then
         * the PF does not have the capability to set the minimum or
         * maximum bandwidths for its children VFs.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_BW_CFG_SUPPORTED \
                UINT32_C(0x400)
        /*
         * Standard TX Ring mode is used for the allocation of TX ring
         * and underlying scheduling resources that allow bandwidth
         * reservation and limit settings on the queried function.
         * If set to 1, then standard TX ring mode is supported
         * on the queried function.
         * If set to 0, then standard TX ring mode is not available
         * on the queried function.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_STD_TX_RING_MODE_SUPPORTED \
                UINT32_C(0x800)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to detect GENEVE tunnel
         * flags.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GENEVE_TUN_FLAGS_SUPPORTED \
                UINT32_C(0x1000)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to detect NVGRE tunnel
         * flags.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_NVGRE_TUN_FLAGS_SUPPORTED \
                UINT32_C(0x2000)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to detect GRE tunnel
         * flags.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GRE_TUN_FLAGS_SUPPORTED \
                UINT32_C(0x4000)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to detect MPLS tunnel
         * flags.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_MPLS_TUN_FLAGS_SUPPORTED \
                UINT32_C(0x8000)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to support pcie stats.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PCIE_STATS_SUPPORTED \
                UINT32_C(0x10000)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to adopt the VF's belonging
         * to another PF.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ADOPTED_PF_SUPPORTED \
                UINT32_C(0x20000)
        /*
         * If the query is for a VF, then this flag shall be ignored,
         * If this query is for a PF and this flag is set to 1,
         * then the PF has the capability to administer another PF.
         */
        #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ADMIN_PF_SUPPORTED \
                UINT32_C(0x40000)
        /*
         * This value is current MAC address configured for this
         * function. A value of 00-00-00-00-00-00 indicates no
         * MAC address is currently configured.
         */
        uint8_t mac_address[6];
        /*
         * The maximum number of RSS/COS contexts that can be
         * allocated to the function.
         */
        uint16_t        max_rsscos_ctx;
        /*
         * The maximum number of completion rings that can be
         * allocated to the function.
         */
        uint16_t        max_cmpl_rings;
        /*
         * The maximum number of transmit rings that can be
         * allocated to the function.
         */
        uint16_t        max_tx_rings;
        /*
         * The maximum number of receive rings that can be
         * allocated to the function.
         */
        uint16_t        max_rx_rings;
        /*
         * The maximum number of L2 contexts that can be
         * allocated to the function.
         */
        uint16_t        max_l2_ctxs;
        /*
         * The maximum number of VNICs that can be
         * allocated to the function.
         */
        uint16_t        max_vnics;
        /*
         * The identifier for the first VF enabled on a PF. This
         * is valid only on the PF with SR-IOV enabled.
         * 0xFF... (All Fs) if this command is called on a PF with
         * SR-IOV disabled or on a VF.
         */
        uint16_t        first_vf_id;
        /*
         * The maximum number of VFs that can be
         * allocated to the function. This is valid only on the
         * PF with SR-IOV enabled. 0xFF... (All Fs) if this
         * command is called on a PF with SR-IOV disabled or
         * on a VF.
         */
        uint16_t        max_vfs;
        /*
         * The maximum number of statistic contexts that can be
         * allocated to the function.
         */
        uint16_t        max_stat_ctx;
        /*
         * The maximum number of Encapsulation records that can be
         * offloaded by this function.
         */
        uint32_t        max_encap_records;
        /*
         * The maximum number of decapsulation records that can
         * be offloaded by this function.
         */
        uint32_t        max_decap_records;
        /*
         * The maximum number of Exact Match (EM) flows that can be
         * offloaded by this function on the TX side.
         */
        uint32_t        max_tx_em_flows;
        /*
         * The maximum number of Wildcard Match (WM) flows that can
         * be offloaded by this function on the TX side.
         */
        uint32_t        max_tx_wm_flows;
        /*
         * The maximum number of Exact Match (EM) flows that can be
         * offloaded by this function on the RX side.
         */
        uint32_t        max_rx_em_flows;
        /*
         * The maximum number of Wildcard Match (WM) flows that can
         * be offloaded by this function on the RX side.
         */
        uint32_t        max_rx_wm_flows;
        /*
         * The maximum number of multicast filters that can
         * be supported by this function on the RX side.
         */
        uint32_t        max_mcast_filters;
        /*
         * The maximum value of flow_id that can be supported
         * in completion records.
         */
        uint32_t        max_flow_id;
        /*
         * The maximum number of HW ring groups that can be
         * supported on this function.
         */
        uint32_t        max_hw_ring_grps;
        /*
         * The maximum number of strict priority transmit rings
         * that can be allocated to the function.
         * This number indicates the maximum number of TX rings
         * that can be assigned strict priorities out of the
         * maximum number of TX rings that can be allocated
         * (max_tx_rings) to the function.
         */
        uint16_t        max_sp_tx_rings;
        uint8_t unused_0;
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************
 * hwrm_func_qcfg *
 ******************/


/* hwrm_func_qcfg_input (size:192b/24B) */
struct hwrm_func_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being queried.
         * 0xFF... (All Fs) if the query is for the requesting
         * function.
         */
        uint16_t        fid;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_qcfg_output (size:640b/80B) */
struct hwrm_func_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * FID value.  This value is used to identify operations on the PCI
         * bus as belonging to a particular PCI function.
         */
        uint16_t        fid;
        /*
         * Port ID of port that this function is associated with.
         * 0xFF... (All Fs) if this function is not associated with
         * any port.
         */
        uint16_t        port_id;
        /*
         * This value is the current VLAN setting for this
         * function. The value of 0 for this field indicates
         * no priority tagging or VLAN is used.
         * This field's format is same as 802.1Q Tag's
         * Tag Control Information (TCI) format that includes both
         * Priority Code Point (PCP) and VLAN Identifier (VID).
         */
        uint16_t        vlan;
        uint16_t        flags;
        /*
         * If 1, then magic packet based Out-Of-Box WoL is enabled on
         * the port associated with this function.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_MAGICPKT_ENABLED \
                UINT32_C(0x1)
        /*
         * If 1, then bitmap pattern based Out-Of-Box WoL packet is enabled
         * on the port associated with this function.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_BMP_ENABLED \
                UINT32_C(0x2)
        /*
         * If set to 1, then FW based DCBX agent is enabled and running on
         * the port associated with this function.
         * If set to 0, then DCBX agent is not running in the firmware.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_DCBX_AGENT_ENABLED \
                UINT32_C(0x4)
        /*
         * Standard TX Ring mode is used for the allocation of TX ring
         * and underlying scheduling resources that allow bandwidth
         * reservation and limit settings on the queried function.
         * If set to 1, then standard TX ring mode is enabled
         * on the queried function.
         * If set to 0, then the standard TX ring mode is disabled
         * on the queried function. In this extended TX ring resource
         * mode, the minimum and maximum bandwidth settings are not
         * supported to allow the allocation of TX rings to span multiple
         * scheduler nodes.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_STD_TX_RING_MODE_ENABLED \
                UINT32_C(0x8)
        /*
         * If set to 1 then FW based LLDP agent is enabled and running on
         * the port associated with this function.
         * If set to 0 then the LLDP agent is not running in the firmware.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_LLDP_AGENT_ENABLED \
                UINT32_C(0x10)
        /*
         * If set to 1, then multi-host mode is active for this function.
         * If set to 0, then multi-host mode is inactive for this function
         * or not applicable for this device.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_MULTI_HOST \
                UINT32_C(0x20)
        /*
         * This value is current MAC address configured for this
         * function. A value of 00-00-00-00-00-00 indicates no
         * MAC address is currently configured.
         */
        uint8_t mac_address[6];
        /*
         * This value is current PCI ID of this
         * function. If ARI is enabled, then it is
         * Bus Number (8b):Function Number(8b). Otherwise, it is
         * Bus Number (8b):Device Number (4b):Function Number(4b).
         * If multi-host mode is active, the 4 lsb will indicate
         * the PF index for this function.
         */
        uint16_t        pci_id;
        /*
         * The number of RSS/COS contexts currently
         * allocated to the function.
         */
        uint16_t        alloc_rsscos_ctx;
        /*
         * The number of completion rings currently allocated to
         * the function. This does not include the rings allocated
         * to any children functions if any.
         */
        uint16_t        alloc_cmpl_rings;
        /*
         * The number of transmit rings currently allocated to
         * the function. This does not include the rings allocated
         * to any children functions if any.
         */
        uint16_t        alloc_tx_rings;
        /*
         * The number of receive rings currently allocated to
         * the function. This does not include the rings allocated
         * to any children functions if any.
         */
        uint16_t        alloc_rx_rings;
        /* The allocated number of L2 contexts to the function. */
        uint16_t        alloc_l2_ctx;
        /* The allocated number of vnics to the function. */
        uint16_t        alloc_vnics;
        /*
         * The maximum transmission unit of the function.
         * For rings allocated on this function, this default
         * value is used if ring MTU is not specified.
         */
        uint16_t        mtu;
        /*
         * The maximum receive unit of the function.
         * For vnics allocated on this function, this default
         * value is used if vnic MRU is not specified.
         */
        uint16_t        mru;
        /* The statistics context assigned to a function. */
        uint16_t        stat_ctx_id;
        /*
         * The HWRM shall return Unknown value for this field
         * when this command is used to query VF's configuration.
         */
        uint8_t port_partition_type;
        /* Single physical function */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_SPF     UINT32_C(0x0)
        /* Multiple physical functions */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_MPFS    UINT32_C(0x1)
        /* Network Partitioning 1.0 */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_0 UINT32_C(0x2)
        /* Network Partitioning 1.5 */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_5 UINT32_C(0x3)
        /* Network Partitioning 2.0 */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR2_0 UINT32_C(0x4)
        /* Unknown */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_LAST \
                HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_UNKNOWN
        /*
         * This field will indicate number of physical functions on this port_partition.
         * HWRM shall return unavail (i.e. value of 0) for this field
         * when this command is used to query VF's configuration or
         * from older firmware that doesn't support this field.
         */
        uint8_t port_pf_cnt;
        /* number of PFs is not available */
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_UNAVAIL UINT32_C(0x0)
        #define HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_LAST \
                HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_UNAVAIL
        /*
         * The default VNIC ID assigned to a function that is
         * being queried.
         */
        uint16_t        dflt_vnic_id;
        uint16_t        max_mtu_configured;
        /*
         * Minimum BW allocated for this function.
         * The HWRM will translate this value into byte counter and
         * time interval used for the scheduler inside the device.
         * A value of 0 indicates the minimum bandwidth is not
         * configured.
         */
        uint32_t        min_bw;
        /* The bandwidth value. */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_SFT              0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_LAST \
                HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_SFT         29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated for this function.
         * The HWRM will translate this value into byte counter and
         * time interval used for the scheduler inside the device.
         * A value of 0 indicates that the maximum bandwidth is not
         * configured.
         */
        uint32_t        max_bw;
        /* The bandwidth value. */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_SFT              0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_LAST \
                HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_SFT         29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID
        /*
         * This value indicates the Edge virtual bridge mode for the
         * domain that this function belongs to.
         */
        uint8_t evb_mode;
        /* No Edge Virtual Bridging (EVB) */
        #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
        /* Virtual Ethernet Bridge (VEB) */
        #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEB    UINT32_C(0x1)
        /* Virtual Ethernet Port Aggregator (VEPA) */
        #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEPA   UINT32_C(0x2)
        #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_LAST \
                HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEPA
        uint8_t options;
        /*
         * This value indicates the PCIE device cache line size.
         * The cache line size allows the DMA writes to terminate and
         * start at the cache boundary.
         */
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_CACHE_LINESIZE_MASK \
                UINT32_C(0x3)
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_CACHE_LINESIZE_SFT     0
        /* Cache Line Size 64 bytes */
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_CACHE_LINESIZE_SIZE_64 \
                UINT32_C(0x0)
        /* Cache Line Size 128 bytes */
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_CACHE_LINESIZE_SIZE_128 \
                UINT32_C(0x1)
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_CACHE_LINESIZE_LAST \
                HWRM_FUNC_QCFG_OUTPUT_OPTIONS_CACHE_LINESIZE_SIZE_128
        /* Reserved for future. */
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_RSVD_MASK \
                UINT32_C(0xfc)
        #define HWRM_FUNC_QCFG_OUTPUT_OPTIONS_RSVD_SFT               2
        /*
         * The number of VFs that are allocated to the function.
         * This is valid only on the PF with SR-IOV enabled.
         * 0xFF... (All Fs) if this command is called on a PF with
         * SR-IOV disabled or on a VF.
         */
        uint16_t        alloc_vfs;
        /*
         * The number of allocated multicast filters for this
         * function on the RX side.
         */
        uint32_t        alloc_mcast_filters;
        /*
         * The number of allocated HW ring groups for this
         * function.
         */
        uint32_t        alloc_hw_ring_grps;
        /*
         * The number of strict priority transmit rings out of
         * currently allocated TX rings to the function
         * (alloc_tx_rings).
         */
        uint16_t        alloc_sp_tx_rings;
        /*
         * The number of statistics contexts
         * currently reserved for the function.
         */
        uint16_t        alloc_stat_ctx;
        /*
         * This field specifies how many NQs are reserved for the PF.
         * Remaining NQs that belong to the PF are available for VFs.
         * Once a PF has created VFs, it cannot change how many NQs are
         * reserved for itself (since the NQs must be contiguous in HW).
         */
        uint16_t        alloc_msix;
        uint8_t unused_2[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_func_vlan_qcfg *
 ***********************/


/* hwrm_func_vlan_qcfg_input (size:192b/24B) */
struct hwrm_func_vlan_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being
         * configured.
         * If set to 0xFF... (All Fs), then the configuration is
         * for the requesting function.
         */
        uint16_t        fid;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_vlan_qcfg_output (size:320b/40B) */
struct hwrm_func_vlan_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
        /* S-TAG VLAN identifier configured for the function. */
        uint16_t        stag_vid;
        /* S-TAG PCP value configured for the function. */
        uint8_t stag_pcp;
        uint8_t unused_1;
        /*
         * S-TAG TPID value configured for the function. This field is specified in
         * network byte order.
         */
        uint16_t        stag_tpid;
        /* C-TAG VLAN identifier configured for the function. */
        uint16_t        ctag_vid;
        /* C-TAG PCP value configured for the function. */
        uint8_t ctag_pcp;
        uint8_t unused_2;
        /*
         * C-TAG TPID value configured for the function. This field is specified in
         * network byte order.
         */
        uint16_t        ctag_tpid;
        /* Future use. */
        uint32_t        rsvd2;
        /* Future use. */
        uint32_t        rsvd3;
        uint32_t        unused_3;
} __attribute__((packed));

/**********************
 * hwrm_func_vlan_cfg *
 **********************/


/* hwrm_func_vlan_cfg_input (size:384b/48B) */
struct hwrm_func_vlan_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being
         * configured.
         * If set to 0xFF... (All Fs), then the configuration is
         * for the requesting function.
         */
        uint16_t        fid;
        uint8_t unused_0[2];
        uint32_t        enables;
        /*
         * This bit must be '1' for the stag_vid field to be
         * configured.
         */
        #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_VID      UINT32_C(0x1)
        /*
         * This bit must be '1' for the ctag_vid field to be
         * configured.
         */
        #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_VID      UINT32_C(0x2)
        /*
         * This bit must be '1' for the stag_pcp field to be
         * configured.
         */
        #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_PCP      UINT32_C(0x4)
        /*
         * This bit must be '1' for the ctag_pcp field to be
         * configured.
         */
        #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_PCP      UINT32_C(0x8)
        /*
         * This bit must be '1' for the stag_tpid field to be
         * configured.
         */
        #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_TPID     UINT32_C(0x10)
        /*
         * This bit must be '1' for the ctag_tpid field to be
         * configured.
         */
        #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_TPID     UINT32_C(0x20)
        /* S-TAG VLAN identifier configured for the function. */
        uint16_t        stag_vid;
        /* S-TAG PCP value configured for the function. */
        uint8_t stag_pcp;
        uint8_t unused_1;
        /*
         * S-TAG TPID value configured for the function. This field is specified in
         * network byte order.
         */
        uint16_t        stag_tpid;
        /* C-TAG VLAN identifier configured for the function. */
        uint16_t        ctag_vid;
        /* C-TAG PCP value configured for the function. */
        uint8_t ctag_pcp;
        uint8_t unused_2;
        /*
         * C-TAG TPID value configured for the function. This field is specified in
         * network byte order.
         */
        uint16_t        ctag_tpid;
        /* Future use. */
        uint32_t        rsvd1;
        /* Future use. */
        uint32_t        rsvd2;
        uint8_t unused_3[4];
} __attribute__((packed));

/* hwrm_func_vlan_cfg_output (size:128b/16B) */
struct hwrm_func_vlan_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************
 * hwrm_func_cfg *
 *****************/


/* hwrm_func_cfg_input (size:704b/88B) */
struct hwrm_func_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being
         * configured.
         * If set to 0xFF... (All Fs), then the the configuration is
         * for the requesting function.
         */
        uint16_t        fid;
        /*
         * This field specifies how many NQs will be reserved for the PF.
         * Remaining NQs that belong to the PF become available for VFs.
         * Once a PF has created VFs, it cannot change how many NQs are
         * reserved for itself (since the NQs must be contiguous in HW).
         */
        uint16_t        num_msix;
        uint32_t        flags;
        /*
         * When this bit is '1', the function is disabled with
         * source MAC address check.
         * This is an anti-spoofing check. If this flag is set,
         * then the function shall be configured to disallow
         * transmission of frames with the source MAC address that
         * is configured for this function.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_DISABLE \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the function is enabled with
         * source MAC address check.
         * This is an anti-spoofing check. If this flag is set,
         * then the function shall be configured to allow
         * transmission of frames with the source MAC address that
         * is configured for this function.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_ENABLE \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_MASK \
                UINT32_C(0x1fc)
        #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_SFT                       2
        /*
         * Standard TX Ring mode is used for the allocation of TX ring
         * and underlying scheduling resources that allow bandwidth
         * reservation and limit settings on the queried function.
         * If set to 1, then standard TX ring mode is requested to be
         * enabled on the function being configured.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_ENABLE \
                UINT32_C(0x200)
        /*
         * Standard TX Ring mode is used for the allocation of TX ring
         * and underlying scheduling resources that allow bandwidth
         * reservation and limit settings on the queried function.
         * If set to 1, then the standard TX ring mode is requested to
         * be disabled on the function being configured. In this extended
         * TX ring resource mode, the minimum and maximum bandwidth settings
         * are not supported to allow the allocation of TX rings to
         * span multiple scheduler nodes.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_DISABLE \
                UINT32_C(0x400)
        /*
         * If this bit is set, virtual mac address configured
         * in this command will be persistent over warm boot.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_VIRT_MAC_PERSIST \
                UINT32_C(0x800)
        /*
         * This bit only applies to the VF. If this bit is set, the statistic
         * context counters will not be cleared when the statistic context is freed
         * or a function reset is called on VF. This bit will be cleared when the PF
         * is unloaded or a function reset is called on the PF.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_NO_AUTOCLEAR_STATISTIC \
                UINT32_C(0x1000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of TX rings) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_TX_ASSETS_TEST \
                UINT32_C(0x2000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of RX rings) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_RX_ASSETS_TEST \
                UINT32_C(0x4000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of CMPL rings) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_CMPL_ASSETS_TEST \
                UINT32_C(0x8000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of RSS ctx) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_RSSCOS_CTX_ASSETS_TEST \
                UINT32_C(0x10000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of ring groups) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_RING_GRP_ASSETS_TEST \
                UINT32_C(0x20000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of stat ctx) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_STAT_CTX_ASSETS_TEST \
                UINT32_C(0x40000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of VNICs) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_VNIC_ASSETS_TEST \
                UINT32_C(0x80000)
        /*
         * This bit requests that the firmware test to see if all the assets
         * requested in this command (i.e. number of L2 ctx) are available.
         * The firmware will return an error if the requested assets are
         * not available. The firwmare will NOT reserve the assets if they
         * are available.
         */
        #define HWRM_FUNC_CFG_INPUT_FLAGS_L2_CTX_ASSETS_TEST \
                UINT32_C(0x100000)
        uint32_t        enables;
        /*
         * This bit must be '1' for the mtu field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the mru field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_MRU \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the num_rsscos_ctxs field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the num_cmpl_rings field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_CMPL_RINGS \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the num_tx_rings field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_TX_RINGS \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the num_rx_rings field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RX_RINGS \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the num_l2_ctxs field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_L2_CTXS \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the num_vnics field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_VNICS \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the num_stat_ctxs field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_STAT_CTXS \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the dflt_mac_addr field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_MAC_ADDR \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the dflt_vlan field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_VLAN \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the dflt_ip_addr field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_IP_ADDR \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the min_bw field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_MIN_BW \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the max_bw field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_MAX_BW \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the async_event_cr field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_ASYNC_EVENT_CR \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the vlan_antispoof_mode field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_VLAN_ANTISPOOF_MODE \
                UINT32_C(0x8000)
        /*
         * This bit must be '1' for the allowed_vlan_pris field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_ALLOWED_VLAN_PRIS \
                UINT32_C(0x10000)
        /*
         * This bit must be '1' for the evb_mode field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_EVB_MODE \
                UINT32_C(0x20000)
        /*
         * This bit must be '1' for the num_mcast_filters field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MCAST_FILTERS \
                UINT32_C(0x40000)
        /*
         * This bit must be '1' for the num_hw_ring_grps field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS \
                UINT32_C(0x80000)
        /*
         * This bit must be '1' for the cache_linesize field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_CACHE_LINESIZE \
                UINT32_C(0x100000)
        /*
         * This bit must be '1' for the num_msix field to be
         * configured.
         */
        #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MSIX \
                UINT32_C(0x200000)
        /*
         * The maximum transmission unit of the function.
         * The HWRM should make sure that the mtu of
         * the function does not exceed the mtu of the physical
         * port that this function is associated with.
         *
         * In addition to configuring mtu per function, it is
         * possible to configure mtu per transmit ring.
         * By default, the mtu of each transmit ring associated
         * with a function is equal to the mtu of the function.
         * The HWRM should make sure that the mtu of each transmit
         * ring that is assigned to a function has a valid mtu.
         */
        uint16_t        mtu;
        /*
         * The maximum receive unit of the function.
         * The HWRM should make sure that the mru of
         * the function does not exceed the mru of the physical
         * port that this function is associated with.
         *
         * In addition to configuring mru per function, it is
         * possible to configure mru per vnic.
         * By default, the mru of each vnic associated
         * with a function is equal to the mru of the function.
         * The HWRM should make sure that the mru of each vnic
         * that is assigned to a function has a valid mru.
         */
        uint16_t        mru;
        /*
         * The number of RSS/COS contexts requested for the
         * function.
         */
        uint16_t        num_rsscos_ctxs;
        /*
         * The number of completion rings requested for the
         * function. This does not include the rings allocated
         * to any children functions if any.
         */
        uint16_t        num_cmpl_rings;
        /*
         * The number of transmit rings requested for the function.
         * This does not include the rings allocated to any
         * children functions if any.
         */
        uint16_t        num_tx_rings;
        /*
         * The number of receive rings requested for the function.
         * This does not include the rings allocated
         * to any children functions if any.
         */
        uint16_t        num_rx_rings;
        /* The requested number of L2 contexts for the function. */
        uint16_t        num_l2_ctxs;
        /* The requested number of vnics for the function. */
        uint16_t        num_vnics;
        /* The requested number of statistic contexts for the function. */
        uint16_t        num_stat_ctxs;
        /*
         * The number of HW ring groups that should
         * be reserved for this function.
         */
        uint16_t        num_hw_ring_grps;
        /* The default MAC address for the function being configured. */
        uint8_t dflt_mac_addr[6];
        /*
         * The default VLAN for the function being configured.
         * This field's format is same as 802.1Q Tag's
         * Tag Control Information (TCI) format that includes both
         * Priority Code Point (PCP) and VLAN Identifier (VID).
         */
        uint16_t        dflt_vlan;
        /*
         * The default IP address for the function being configured.
         * This address is only used in enabling source property check.
         */
        uint32_t        dflt_ip_addr[4];
        /*
         * Minimum BW allocated for this function.
         * The HWRM will translate this value into byte counter and
         * time interval used for the scheduler inside the device.
         */
        uint32_t        min_bw;
        /* The bandwidth value. */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_SFT              0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_LAST \
                HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_SFT         29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated for this function.
         * The HWRM will translate this value into byte counter and
         * time interval used for the scheduler inside the device.
         */
        uint32_t        max_bw;
        /* The bandwidth value. */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_SFT              0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_LAST \
                HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_SFT         29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
        /*
         * ID of the target completion ring for receiving asynchronous
         * event completions. If this field is not valid, then the
         * HWRM shall use the default completion ring of the function
         * that is being configured as the target completion ring for
         * providing any asynchronous event completions for that
         * function.
         * If this field is valid, then the HWRM shall use the
         * completion ring identified by this ID as the target
         * completion ring for providing any asynchronous event
         * completions for the function that is being configured.
         */
        uint16_t        async_event_cr;
        /* VLAN Anti-spoofing mode. */
        uint8_t vlan_antispoof_mode;
        /* No VLAN anti-spoofing checks are enabled */
        #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_NOCHECK \
                UINT32_C(0x0)
        /* Validate VLAN against the configured VLAN(s) */
        #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_VALIDATE_VLAN \
                UINT32_C(0x1)
        /* Insert VLAN if it does not exist, otherwise discard */
        #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_IF_VLANDNE \
                UINT32_C(0x2)
        /* Insert VLAN if it does not exist, override VLAN if it exists */
        #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN \
                UINT32_C(0x3)
        #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_LAST \
                HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN
        /*
         * This bit field defines VLAN PRIs that are allowed on
         * this function.
         * If nth bit is set, then VLAN PRI n is allowed on this
         * function.
         */
        uint8_t allowed_vlan_pris;
        /*
         * The HWRM shall allow a PF driver to change EVB mode for the
         * partition it belongs to.
         * The HWRM shall not allow a VF driver to change the EVB mode.
         * The HWRM shall take into account the switching of EVB mode
         * from one to another and reconfigure hardware resources as
         * appropriately.
         * The switching from VEB to VEPA mode requires
         * the disabling of the loopback traffic. Additionally,
         * source knock outs are handled differently in VEB and VEPA
         * modes.
         */
        uint8_t evb_mode;
        /* No Edge Virtual Bridging (EVB) */
        #define HWRM_FUNC_CFG_INPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
        /* Virtual Ethernet Bridge (VEB) */
        #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEB    UINT32_C(0x1)
        /* Virtual Ethernet Port Aggregator (VEPA) */
        #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA   UINT32_C(0x2)
        #define HWRM_FUNC_CFG_INPUT_EVB_MODE_LAST \
                HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA
        uint8_t options;
        /*
         * This value indicates the PCIE device cache line size.
         * The cache line size allows the DMA writes to terminate and
         * start at the cache boundary.
         */
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_CACHE_LINESIZE_MASK \
                UINT32_C(0x3)
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_CACHE_LINESIZE_SFT     0
        /* Cache Line Size 64 bytes */
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_CACHE_LINESIZE_SIZE_64 \
                UINT32_C(0x0)
        /* Cache Line Size 128 bytes */
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_CACHE_LINESIZE_SIZE_128 \
                UINT32_C(0x1)
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_CACHE_LINESIZE_LAST \
                HWRM_FUNC_CFG_INPUT_OPTIONS_CACHE_LINESIZE_SIZE_128
        /* Reserved for future. */
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_RSVD_MASK \
                UINT32_C(0xfc)
        #define HWRM_FUNC_CFG_INPUT_OPTIONS_RSVD_SFT               2
        /*
         * The number of multicast filters that should
         * be reserved for this function on the RX side.
         */
        uint16_t        num_mcast_filters;
} __attribute__((packed));

/* hwrm_func_cfg_output (size:128b/16B) */
struct hwrm_func_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************
 * hwrm_func_qstats *
 ********************/


/* hwrm_func_qstats_input (size:192b/24B) */
struct hwrm_func_qstats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being queried.
         * 0xFF... (All Fs) if the query is for the requesting
         * function.
         */
        uint16_t        fid;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_qstats_output (size:1408b/176B) */
struct hwrm_func_qstats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Number of transmitted unicast packets on the function. */
        uint64_t        tx_ucast_pkts;
        /* Number of transmitted multicast packets on the function. */
        uint64_t        tx_mcast_pkts;
        /* Number of transmitted broadcast packets on the function. */
        uint64_t        tx_bcast_pkts;
        /*
         * Number of transmitted packets that were discarded due to
         * internal NIC resource problems.  For transmit, this
         * can only happen if TMP is configured to allow dropping
         * in HOL blocking conditions, which is not a normal
         * configuration.
         */
        uint64_t        tx_discard_pkts;
        /*
         * Number of dropped packets on transmit path on the function.
         * These are packets that have been marked for drop by
         * the TE CFA block or are packets that exceeded the
         * transmit MTU limit for the function.
         */
        uint64_t        tx_drop_pkts;
        /* Number of transmitted bytes for unicast traffic on the function. */
        uint64_t        tx_ucast_bytes;
        /* Number of transmitted bytes for multicast traffic on the function. */
        uint64_t        tx_mcast_bytes;
        /* Number of transmitted bytes for broadcast traffic on the function. */
        uint64_t        tx_bcast_bytes;
        /* Number of received unicast packets on the function. */
        uint64_t        rx_ucast_pkts;
        /* Number of received multicast packets on the function. */
        uint64_t        rx_mcast_pkts;
        /* Number of received broadcast packets on the function. */
        uint64_t        rx_bcast_pkts;
        /*
         * Number of received packets that were discarded on the function
         * due to resource limitations.  This can happen for 3 reasons.
         * # The BD used for the packet has a bad format.
         * # There were no BDs available in the ring for the packet.
         * # There were no BDs available on-chip for the packet.
         */
        uint64_t        rx_discard_pkts;
        /*
         * Number of dropped packets on received path on the function.
         * These are packets that have been marked for drop by the
         * RE CFA.
         */
        uint64_t        rx_drop_pkts;
        /* Number of received bytes for unicast traffic on the function. */
        uint64_t        rx_ucast_bytes;
        /* Number of received bytes for multicast traffic on the function. */
        uint64_t        rx_mcast_bytes;
        /* Number of received bytes for broadcast traffic on the function. */
        uint64_t        rx_bcast_bytes;
        /* Number of aggregated unicast packets on the function. */
        uint64_t        rx_agg_pkts;
        /* Number of aggregated unicast bytes on the function. */
        uint64_t        rx_agg_bytes;
        /* Number of aggregation events on the function. */
        uint64_t        rx_agg_events;
        /* Number of aborted aggregations on the function. */
        uint64_t        rx_agg_aborts;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_func_clr_stats *
 ***********************/


/* hwrm_func_clr_stats_input (size:192b/24B) */
struct hwrm_func_clr_stats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function.
         * 0xFF... (All Fs) if the query is for the requesting
         * function.
         */
        uint16_t        fid;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_clr_stats_output (size:128b/16B) */
struct hwrm_func_clr_stats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_func_vf_resc_free *
 **************************/


/* hwrm_func_vf_resc_free_input (size:192b/24B) */
struct hwrm_func_vf_resc_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This value is used to identify a Virtual Function (VF).
         * The scope of VF ID is local within a PF.
         */
        uint16_t        vf_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_vf_resc_free_output (size:128b/16B) */
struct hwrm_func_vf_resc_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************************
 * hwrm_func_vf_vnic_ids_query *
 *******************************/


/* hwrm_func_vf_vnic_ids_query_input (size:256b/32B) */
struct hwrm_func_vf_vnic_ids_query_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This value is used to identify a Virtual Function (VF).
         * The scope of VF ID is local within a PF.
         */
        uint16_t        vf_id;
        uint8_t unused_0[2];
        /* Max number of vnic ids in vnic id table */
        uint32_t        max_vnic_id_cnt;
        /* This is the address for VF VNIC ID table */
        uint64_t        vnic_id_tbl_addr;
} __attribute__((packed));

/* hwrm_func_vf_vnic_ids_query_output (size:128b/16B) */
struct hwrm_func_vf_vnic_ids_query_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * Actual number of vnic ids
         *
         * Each VNIC ID is written as a 32-bit number.
         */
        uint32_t        vnic_id_cnt;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_func_drv_rgtr *
 **********************/


/* hwrm_func_drv_rgtr_input (size:896b/112B) */
struct hwrm_func_drv_rgtr_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is '1', the function driver is requesting
         * all requests from its children VF drivers to be
         * forwarded to itself.
         * This flag can only be set by the PF driver.
         * If a VF driver sets this flag, it should be ignored
         * by the HWRM.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE       UINT32_C(0x1)
        /*
         * When this bit is '1', the function is requesting none of
         * the requests from its children VF drivers to be
         * forwarded to itself.
         * This flag can only be set by the PF driver.
         * If a VF driver sets this flag, it should be ignored
         * by the HWRM.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE      UINT32_C(0x2)
        /*
         * When this bit is '1', then ver_maj_8b, ver_min_8b, ver_upd_8b
         * fields shall be ignored and ver_maj, ver_min, ver_upd
         * and ver_patch shall be used for the driver version information.
         * When this bit is '0', then ver_maj_8b, ver_min_8b, ver_upd_8b
         * fields shall be used for the driver version information and
         * ver_maj, ver_min, ver_upd and ver_patch shall be ignored.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_16BIT_VER_MODE     UINT32_C(0x4)
        uint32_t        enables;
        /*
         * This bit must be '1' for the os_type field to be
         * configured.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the ver field to be
         * configured.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the timestamp field to be
         * configured.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the vf_req_fwd field to be
         * configured.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_REQ_FWD \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the async_event_fwd field to be
         * configured.
         */
        #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD \
                UINT32_C(0x10)
        /* This value indicates the type of OS.  The values are based on CIM_OperatingSystem.mof file as published by the DMTF. */
        uint16_t        os_type;
        /* Unknown */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN   UINT32_C(0x0)
        /* Other OS not listed below. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER     UINT32_C(0x1)
        /* MSDOS OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS     UINT32_C(0xe)
        /* Windows OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS   UINT32_C(0x12)
        /* Solaris OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS   UINT32_C(0x1d)
        /* Linux OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX     UINT32_C(0x24)
        /* FreeBSD OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD   UINT32_C(0x2a)
        /* VMware ESXi OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI      UINT32_C(0x68)
        /* Microsoft Windows 8 64-bit OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864    UINT32_C(0x73)
        /* Microsoft Windows Server 2012 R2 OS. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 UINT32_C(0x74)
        /* UEFI driver. */
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UEFI      UINT32_C(0x8000)
        #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LAST \
                HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UEFI
        /* This is the 8bit major version of the driver. */
        uint8_t ver_maj_8b;
        /* This is the 8bit minor version of the driver. */
        uint8_t ver_min_8b;
        /* This is the 8bit update version of the driver. */
        uint8_t ver_upd_8b;
        uint8_t unused_0[3];
        /*
         * This is a 32-bit timestamp provided by the driver for
         * keep alive.
         * The timestamp is in multiples of 1ms.
         */
        uint32_t        timestamp;
        uint8_t unused_1[4];
        /*
         * This is a 256-bit bit mask provided by the PF driver for
         * letting the HWRM know what commands issued by the VF driver
         * to the HWRM should be forwarded to the PF driver.
         * Nth bit refers to the Nth req_type.
         *
         * Setting Nth bit to 1 indicates that requests from the
         * VF driver with req_type equal to N shall be forwarded to
         * the parent PF driver.
         *
         * This field is not valid for the VF driver.
         */
        uint32_t        vf_req_fwd[8];
        /*
         * This is a 256-bit bit mask provided by the function driver
         * (PF or VF driver) to indicate the list of asynchronous event
         * completions to be forwarded.
         *
         * Nth bit refers to the Nth event_id.
         *
         * Setting Nth bit to 1 by the function driver shall result in
         * the HWRM forwarding asynchronous event completion with
         * event_id equal to N.
         *
         * If all bits are set to 0 (value of 0), then the HWRM shall
         * not forward any asynchronous event completion to this
         * function driver.
         */
        uint32_t        async_event_fwd[8];
        /* This is the 16bit major version of the driver. */
        uint16_t        ver_maj;
        /* This is the 16bit minor version of the driver. */
        uint16_t        ver_min;
        /* This is the 16bit update version of the driver. */
        uint16_t        ver_upd;
        /* This is the 16bit patch version of the driver. */
        uint16_t        ver_patch;
} __attribute__((packed));

/* hwrm_func_drv_rgtr_output (size:128b/16B) */
struct hwrm_func_drv_rgtr_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/************************
 * hwrm_func_drv_unrgtr *
 ************************/


/* hwrm_func_drv_unrgtr_input (size:192b/24B) */
struct hwrm_func_drv_unrgtr_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is '1', the function driver is notifying
         * the HWRM to prepare for the shutdown.
         */
        #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN \
                UINT32_C(0x1)
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_func_drv_unrgtr_output (size:128b/16B) */
struct hwrm_func_drv_unrgtr_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_func_buf_rgtr *
 **********************/


/* hwrm_func_buf_rgtr_input (size:1024b/128B) */
struct hwrm_func_buf_rgtr_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the vf_id field to be
         * configured.
         */
        #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_VF_ID            UINT32_C(0x1)
        /*
         * This bit must be '1' for the err_buf_addr field to be
         * configured.
         */
        #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_ERR_BUF_ADDR     UINT32_C(0x2)
        /*
         * This value is used to identify a Virtual Function (VF).
         * The scope of VF ID is local within a PF.
         */
        uint16_t        vf_id;
        /*
         * This field represents the number of pages used for request
         * buffer(s).
         */
        uint16_t        req_buf_num_pages;
        /*
         * This field represents the page size used for request
         * buffer(s).
         */
        uint16_t        req_buf_page_size;
        /* 16 bytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_16B UINT32_C(0x4)
        /* 4 Kbytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_4K  UINT32_C(0xc)
        /* 8 Kbytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_8K  UINT32_C(0xd)
        /* 64 Kbytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_64K UINT32_C(0x10)
        /* 2 Mbytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_2M  UINT32_C(0x15)
        /* 4 Mbytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_4M  UINT32_C(0x16)
        /* 1 Gbytes */
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_1G  UINT32_C(0x1e)
        #define HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_LAST \
                HWRM_FUNC_BUF_RGTR_INPUT_REQ_BUF_PAGE_SIZE_1G
        /* The length of the request buffer per VF in bytes. */
        uint16_t        req_buf_len;
        /* The length of the response buffer in bytes. */
        uint16_t        resp_buf_len;
        uint8_t unused_0[2];
        /* This field represents the page address of page #0. */
        uint64_t        req_buf_page_addr0;
        /* This field represents the page address of page #1. */
        uint64_t        req_buf_page_addr1;
        /* This field represents the page address of page #2. */
        uint64_t        req_buf_page_addr2;
        /* This field represents the page address of page #3. */
        uint64_t        req_buf_page_addr3;
        /* This field represents the page address of page #4. */
        uint64_t        req_buf_page_addr4;
        /* This field represents the page address of page #5. */
        uint64_t        req_buf_page_addr5;
        /* This field represents the page address of page #6. */
        uint64_t        req_buf_page_addr6;
        /* This field represents the page address of page #7. */
        uint64_t        req_buf_page_addr7;
        /* This field represents the page address of page #8. */
        uint64_t        req_buf_page_addr8;
        /* This field represents the page address of page #9. */
        uint64_t        req_buf_page_addr9;
        /*
         * This field is used to receive the error reporting from
         * the chipset. Only applicable for PFs.
         */
        uint64_t        error_buf_addr;
        /*
         * This field is used to receive the response forwarded by the
         * HWRM.
         */
        uint64_t        resp_buf_addr;
} __attribute__((packed));

/* hwrm_func_buf_rgtr_output (size:128b/16B) */
struct hwrm_func_buf_rgtr_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/************************
 * hwrm_func_buf_unrgtr *
 ************************/


/* hwrm_func_buf_unrgtr_input (size:192b/24B) */
struct hwrm_func_buf_unrgtr_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the vf_id field to be
         * configured.
         */
        #define HWRM_FUNC_BUF_UNRGTR_INPUT_ENABLES_VF_ID     UINT32_C(0x1)
        /*
         * This value is used to identify a Virtual Function (VF).
         * The scope of VF ID is local within a PF.
         */
        uint16_t        vf_id;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_func_buf_unrgtr_output (size:128b/16B) */
struct hwrm_func_buf_unrgtr_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_func_drv_qver *
 **********************/


/* hwrm_func_drv_qver_input (size:192b/24B) */
struct hwrm_func_drv_qver_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Reserved for future use. */
        uint32_t        reserved;
        /*
         * Function ID of the function that is being queried.
         * 0xFF... (All Fs) if the query is for the requesting
         * function.
         */
        uint16_t        fid;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_func_drv_qver_output (size:192b/24B) */
struct hwrm_func_drv_qver_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value indicates the type of OS.  The values are based on CIM_OperatingSystem.mof file as published by the DMTF. */
        uint16_t        os_type;
        /* Unknown */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_UNKNOWN   UINT32_C(0x0)
        /* Other OS not listed below. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_OTHER     UINT32_C(0x1)
        /* MSDOS OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_MSDOS     UINT32_C(0xe)
        /* Windows OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_WINDOWS   UINT32_C(0x12)
        /* Solaris OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_SOLARIS   UINT32_C(0x1d)
        /* Linux OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_LINUX     UINT32_C(0x24)
        /* FreeBSD OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_FREEBSD   UINT32_C(0x2a)
        /* VMware ESXi OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_ESXI      UINT32_C(0x68)
        /* Microsoft Windows 8 64-bit OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_WIN864    UINT32_C(0x73)
        /* Microsoft Windows Server 2012 R2 OS. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_WIN2012R2 UINT32_C(0x74)
        /* UEFI driver. */
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_UEFI      UINT32_C(0x8000)
        #define HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_LAST \
                HWRM_FUNC_DRV_QVER_OUTPUT_OS_TYPE_UEFI
        /* This is the 8bit major version of the driver. */
        uint8_t ver_maj_8b;
        /* This is the 8bit minor version of the driver. */
        uint8_t ver_min_8b;
        /* This is the 8bit update version of the driver. */
        uint8_t ver_upd_8b;
        uint8_t unused_0[2];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
        /* This is the 16bit major version of the driver. */
        uint16_t        ver_maj;
        /* This is the 16bit minor version of the driver. */
        uint16_t        ver_min;
        /* This is the 16bit update version of the driver. */
        uint16_t        ver_upd;
        /* This is the 16bit patch version of the driver. */
        uint16_t        ver_patch;
} __attribute__((packed));

/****************************
 * hwrm_func_resource_qcaps *
 ****************************/


/* hwrm_func_resource_qcaps_input (size:192b/24B) */
struct hwrm_func_resource_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being queried.
         * 0xFF... (All Fs) if the query is for the requesting
         * function.
         */
        uint16_t        fid;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_func_resource_qcaps_output (size:448b/56B) */
struct hwrm_func_resource_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Maximum guaranteed number of VFs supported by PF. Not applicable for VFs. */
        uint16_t        max_vfs;
        /* Maximum guaranteed number of MSI-X vectors supported by function */
        uint16_t        max_msix;
        /* Hint of strategy to be used by PF driver to reserve resources for its VF */
        uint16_t        vf_reservation_strategy;
        /* The PF driver should evenly divide its remaining resources among all VFs. */
        #define HWRM_FUNC_RESOURCE_QCAPS_OUTPUT_VF_RESERVATION_STRATEGY_MAXIMAL \
                UINT32_C(0x0)
        /* The PF driver should only reserve minimal resources for each VF. */
        #define HWRM_FUNC_RESOURCE_QCAPS_OUTPUT_VF_RESERVATION_STRATEGY_MINIMAL \
                UINT32_C(0x1)
        /*
         * The PF driver should not reserve any resources for each VF until the
         * the VF interface is brought up.
         */
        #define HWRM_FUNC_RESOURCE_QCAPS_OUTPUT_VF_RESERVATION_STRATEGY_MINIMAL_STATIC \
                UINT32_C(0x2)
        #define HWRM_FUNC_RESOURCE_QCAPS_OUTPUT_VF_RESERVATION_STRATEGY_LAST \
                HWRM_FUNC_RESOURCE_QCAPS_OUTPUT_VF_RESERVATION_STRATEGY_MINIMAL_STATIC
        /* Minimum guaranteed number of RSS/COS contexts */
        uint16_t        min_rsscos_ctx;
        /* Maximum non-guaranteed number of RSS/COS contexts */
        uint16_t        max_rsscos_ctx;
        /* Minimum guaranteed number of completion rings */
        uint16_t        min_cmpl_rings;
        /* Maximum non-guaranteed number of completion rings */
        uint16_t        max_cmpl_rings;
        /* Minimum guaranteed number of transmit rings */
        uint16_t        min_tx_rings;
        /* Maximum non-guaranteed number of transmit rings */
        uint16_t        max_tx_rings;
        /* Minimum guaranteed number of receive rings */
        uint16_t        min_rx_rings;
        /* Maximum non-guaranteed number of receive rings */
        uint16_t        max_rx_rings;
        /* Minimum guaranteed number of L2 contexts */
        uint16_t        min_l2_ctxs;
        /* Maximum non-guaranteed number of L2 contexts */
        uint16_t        max_l2_ctxs;
        /* Minimum guaranteed number of VNICs */
        uint16_t        min_vnics;
        /* Maximum non-guaranteed number of VNICs */
        uint16_t        max_vnics;
        /* Minimum guaranteed number of statistic contexts */
        uint16_t        min_stat_ctx;
        /* Maximum non-guaranteed number of statistic contexts */
        uint16_t        max_stat_ctx;
        /* Minimum guaranteed number of ring groups */
        uint16_t        min_hw_ring_grps;
        /* Maximum non-guaranteed number of ring groups */
        uint16_t        max_hw_ring_grps;
        /*
         * Maximum number of inputs into the transmit scheduler for this function.
         * The number of TX rings assigned to the function cannot exceed this value.
         */
        uint16_t        max_tx_scheduler_inputs;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************************
 * hwrm_func_vf_resource_cfg *
 *****************************/


/* hwrm_func_vf_resource_cfg_input (size:448b/56B) */
struct hwrm_func_vf_resource_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* VF ID that is being configured by PF */
        uint16_t        vf_id;
        /* Maximum guaranteed number of MSI-X vectors for the function */
        uint16_t        max_msix;
        /* Minimum guaranteed number of RSS/COS contexts */
        uint16_t        min_rsscos_ctx;
        /* Maximum non-guaranteed number of RSS/COS contexts */
        uint16_t        max_rsscos_ctx;
        /* Minimum guaranteed number of completion rings */
        uint16_t        min_cmpl_rings;
        /* Maximum non-guaranteed number of completion rings */
        uint16_t        max_cmpl_rings;
        /* Minimum guaranteed number of transmit rings */
        uint16_t        min_tx_rings;
        /* Maximum non-guaranteed number of transmit rings */
        uint16_t        max_tx_rings;
        /* Minimum guaranteed number of receive rings */
        uint16_t        min_rx_rings;
        /* Maximum non-guaranteed number of receive rings */
        uint16_t        max_rx_rings;
        /* Minimum guaranteed number of L2 contexts */
        uint16_t        min_l2_ctxs;
        /* Maximum non-guaranteed number of L2 contexts */
        uint16_t        max_l2_ctxs;
        /* Minimum guaranteed number of VNICs */
        uint16_t        min_vnics;
        /* Maximum non-guaranteed number of VNICs */
        uint16_t        max_vnics;
        /* Minimum guaranteed number of statistic contexts */
        uint16_t        min_stat_ctx;
        /* Maximum non-guaranteed number of statistic contexts */
        uint16_t        max_stat_ctx;
        /* Minimum guaranteed number of ring groups */
        uint16_t        min_hw_ring_grps;
        /* Maximum non-guaranteed number of ring groups */
        uint16_t        max_hw_ring_grps;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_func_vf_resource_cfg_output (size:256b/32B) */
struct hwrm_func_vf_resource_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Reserved number of RSS/COS contexts */
        uint16_t        reserved_rsscos_ctx;
        /* Reserved number of completion rings */
        uint16_t        reserved_cmpl_rings;
        /* Reserved number of transmit rings */
        uint16_t        reserved_tx_rings;
        /* Reserved number of receive rings */
        uint16_t        reserved_rx_rings;
        /* Reserved number of L2 contexts */
        uint16_t        reserved_l2_ctxs;
        /* Reserved number of VNICs */
        uint16_t        reserved_vnics;
        /* Reserved number of statistic contexts */
        uint16_t        reserved_stat_ctx;
        /* Reserved number of ring groups */
        uint16_t        reserved_hw_ring_grps;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************************
 * hwrm_func_backing_store_qcaps *
 *********************************/


/* hwrm_func_backing_store_qcaps_input (size:128b/16B) */
struct hwrm_func_backing_store_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_func_backing_store_qcaps_output (size:512b/64B) */
struct hwrm_func_backing_store_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Maximum number of QP context entries supported for this function. */
        uint32_t        qp_max_entries;
        /*
         * Minimum number of QP context entries that are needed to be reserved
         * for QP1 for the PF and its VFs. PF drivers must allocate at least
         * this many QP context entries, even if RoCE will not be used.
         */
        uint16_t        qp_min_qp1_entries;
        /* Maximum number of QP context entries that can be used for L2. */
        uint16_t        qp_max_l2_entries;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        qp_entry_size;
        /* Maximum number of SRQ context entries that can be used for L2. */
        uint16_t        srq_max_l2_entries;
        /* Maximum number of SRQ context entries supported for this function. */
        uint32_t        srq_max_entries;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        srq_entry_size;
        /* Maximum number of CQ context entries that can be used for L2. */
        uint16_t        cq_max_l2_entries;
        /* Maximum number of CQ context entries supported for this function. */
        uint32_t        cq_max_entries;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        cq_entry_size;
        /* Maximum number of VNIC context entries supported for this function. */
        uint16_t        vnic_max_vnic_entries;
        /* Maximum number of Ring table context entries supported for this function. */
        uint16_t        vnic_max_ring_table_entries;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        vnic_entry_size;
        /* Maximum number of statistic context entries supported for this function. */
        uint32_t        stat_max_entries;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        stat_entry_size;
        /* Maximum number of TQM context entries supported per ring. */
        uint16_t        tqm_max_entries_per_ring;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        tqm_entry_size;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        mrav_entry_size;
        /* Maximum number of MR/AV context entries supported for this function. */
        uint32_t        mrav_max_entries;
        /* Maximum number of Timer context entries supported for this function. */
        uint32_t        tim_max_entries;
        /* Number of bytes that must be allocated for each context entry. */
        uint16_t        tim_entry_size;
        uint8_t unused_0;
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************************
 * hwrm_func_backing_store_cfg *
 *******************************/


/* hwrm_func_backing_store_cfg_input (size:2048b/256B) */
struct hwrm_func_backing_store_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When set, the firmware only uses on-chip resources and does not
         * expect any backing store to be provided by the host driver. This
         * mode provides minimal L2 functionality (e.g. limited L2 resources,
         * no RoCE).
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_FLAGS_PREBOOT_MODE \
                UINT32_C(0x1)
        uint32_t        enables;
        /*
         * This bit must be '1' for the qp fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_QP \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the srq fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_SRQ \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the cq fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_CQ \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the vnic fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_VNIC \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the stat fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_STAT \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the tqm_sp fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_SP \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the tqm_ring0 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING0 \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the tqm_ring1 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING1 \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the tqm_ring2 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING2 \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the tqm_ring3 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING3 \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the tqm_ring4 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING4 \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the tqm_ring5 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING5 \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the tqm_ring6 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING6 \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the tqm_ring7 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TQM_RING7 \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the mrav fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_MRAV \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the tim fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_ENABLES_TIM \
                UINT32_C(0x8000)
        /* QPC page size and level. */
        uint8_t qpc_pg_size_qpc_lvl;
        /* QPC PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_LVL_LVL_2
        /* QPC page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_QPC_PG_SIZE_PG_1G
        /* SRQ page size and level. */
        uint8_t srq_pg_size_srq_lvl;
        /* SRQ PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_LVL_LVL_2
        /* SRQ page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_SRQ_PG_SIZE_PG_1G
        /* CQ page size and level. */
        uint8_t cq_pg_size_cq_lvl;
        /* CQ PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_LVL_LVL_2
        /* CQ page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_CQ_PG_SIZE_PG_1G
        /* VNIC page size and level. */
        uint8_t vnic_pg_size_vnic_lvl;
        /* VNIC PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_LVL_LVL_2
        /* VNIC page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_VNIC_PG_SIZE_PG_1G
        /* Stat page size and level. */
        uint8_t stat_pg_size_stat_lvl;
        /* Stat PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_LVL_LVL_2
        /* Stat page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_STAT_PG_SIZE_PG_1G
        /* TQM slow path page size and level. */
        uint8_t tqm_sp_pg_size_tqm_sp_lvl;
        /* TQM slow path PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_LVL_LVL_2
        /* TQM slow path page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_SP_PG_SIZE_PG_1G
        /* TQM ring 0 page size and level. */
        uint8_t tqm_ring0_pg_size_tqm_ring0_lvl;
        /* TQM ring 0 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_LVL_LVL_2
        /* TQM ring 0 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING0_PG_SIZE_PG_1G
        /* TQM ring 1 page size and level. */
        uint8_t tqm_ring1_pg_size_tqm_ring1_lvl;
        /* TQM ring 1 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_LVL_LVL_2
        /* TQM ring 1 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING1_PG_SIZE_PG_1G
        /* TQM ring 2 page size and level. */
        uint8_t tqm_ring2_pg_size_tqm_ring2_lvl;
        /* TQM ring 2 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_LVL_LVL_2
        /* TQM ring 2 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING2_PG_SIZE_PG_1G
        /* TQM ring 3 page size and level. */
        uint8_t tqm_ring3_pg_size_tqm_ring3_lvl;
        /* TQM ring 3 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_LVL_LVL_2
        /* TQM ring 3 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING3_PG_SIZE_PG_1G
        /* TQM ring 4 page size and level. */
        uint8_t tqm_ring4_pg_size_tqm_ring4_lvl;
        /* TQM ring 4 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_LVL_LVL_2
        /* TQM ring 4 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING4_PG_SIZE_PG_1G
        /* TQM ring 5 page size and level. */
        uint8_t tqm_ring5_pg_size_tqm_ring5_lvl;
        /* TQM ring 5 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_LVL_LVL_2
        /* TQM ring 5 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING5_PG_SIZE_PG_1G
        /* TQM ring 6 page size and level. */
        uint8_t tqm_ring6_pg_size_tqm_ring6_lvl;
        /* TQM ring 6 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_LVL_LVL_2
        /* TQM ring 6 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING6_PG_SIZE_PG_1G
        /* TQM ring 7 page size and level. */
        uint8_t tqm_ring7_pg_size_tqm_ring7_lvl;
        /* TQM ring 7 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_LVL_LVL_2
        /* TQM ring 7 page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TQM_RING7_PG_SIZE_PG_1G
        /* MR/AV page size and level. */
        uint8_t mrav_pg_size_mrav_lvl;
        /* MR/AV PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_LVL_LVL_2
        /* MR/AV page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_MRAV_PG_SIZE_PG_1G
        /* Timer page size and level. */
        uint8_t tim_pg_size_tim_lvl;
        /* Timer PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_LVL_LVL_2
        /* Timer page size. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_CFG_INPUT_TIM_PG_SIZE_PG_1G
        /* QP page directory. */
        uint64_t        qpc_page_dir;
        /* SRQ page directory. */
        uint64_t        srq_page_dir;
        /* CQ page directory. */
        uint64_t        cq_page_dir;
        /* VNIC page directory. */
        uint64_t        vnic_page_dir;
        /* Stat page directory. */
        uint64_t        stat_page_dir;
        /* TQM slowpath page directory. */
        uint64_t        tqm_sp_page_dir;
        /* TQM ring 0 page directory. */
        uint64_t        tqm_ring0_page_dir;
        /* TQM ring 1 page directory. */
        uint64_t        tqm_ring1_page_dir;
        /* TQM ring 2 page directory. */
        uint64_t        tqm_ring2_page_dir;
        /* TQM ring 3 page directory. */
        uint64_t        tqm_ring3_page_dir;
        /* TQM ring 4 page directory. */
        uint64_t        tqm_ring4_page_dir;
        /* TQM ring 5 page directory. */
        uint64_t        tqm_ring5_page_dir;
        /* TQM ring 6 page directory. */
        uint64_t        tqm_ring6_page_dir;
        /* TQM ring 7 page directory. */
        uint64_t        tqm_ring7_page_dir;
        /* MR/AV page directory. */
        uint64_t        mrav_page_dir;
        /* Timer page directory. */
        uint64_t        tim_page_dir;
        /* Number of QPs. */
        uint32_t        qp_num_entries;
        /* Number of SRQs. */
        uint32_t        srq_num_entries;
        /* Number of CQs. */
        uint32_t        cq_num_entries;
        /* Number of Stats. */
        uint32_t        stat_num_entries;
        /* Number of TQM slowpath entries. */
        uint32_t        tqm_sp_num_entries;
        /* Number of TQM ring 0 entries. */
        uint32_t        tqm_ring0_num_entries;
        /* Number of TQM ring 1 entries. */
        uint32_t        tqm_ring1_num_entries;
        /* Number of TQM ring 2 entries. */
        uint32_t        tqm_ring2_num_entries;
        /* Number of TQM ring 3 entries. */
        uint32_t        tqm_ring3_num_entries;
        /* Number of TQM ring 4 entries. */
        uint32_t        tqm_ring4_num_entries;
        /* Number of TQM ring 5 entries. */
        uint32_t        tqm_ring5_num_entries;
        /* Number of TQM ring 6 entries. */
        uint32_t        tqm_ring6_num_entries;
        /* Number of TQM ring 7 entries. */
        uint32_t        tqm_ring7_num_entries;
        /* Number of MR/AV entries. */
        uint32_t        mrav_num_entries;
        /* Number of Timer entries. */
        uint32_t        tim_num_entries;
        /* Number of entries to reserve for QP1 */
        uint16_t        qp_num_qp1_entries;
        /* Number of entries to reserve for L2 */
        uint16_t        qp_num_l2_entries;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        qp_entry_size;
        /* Number of entries to reserve for L2 */
        uint16_t        srq_num_l2_entries;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        srq_entry_size;
        /* Number of entries to reserve for L2 */
        uint16_t        cq_num_l2_entries;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        cq_entry_size;
        /* Number of entries to reserve for VNIC entries */
        uint16_t        vnic_num_vnic_entries;
        /* Number of entries to reserve for Ring table entries */
        uint16_t        vnic_num_ring_table_entries;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        vnic_entry_size;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        stat_entry_size;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        tqm_entry_size;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        mrav_entry_size;
        /* Number of bytes that have been allocated for each context entry. */
        uint16_t        tim_entry_size;
} __attribute__((packed));

/* hwrm_func_backing_store_cfg_output (size:128b/16B) */
struct hwrm_func_backing_store_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************************
 * hwrm_func_backing_store_qcfg *
 ********************************/


/* hwrm_func_backing_store_qcfg_input (size:128b/16B) */
struct hwrm_func_backing_store_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_func_backing_store_qcfg_output (size:1920b/240B) */
struct hwrm_func_backing_store_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint32_t        flags;
        /*
         * When set, the firmware only uses on-chip resources and does not
         * expect any backing store to be provided by the host driver. This
         * mode provides minimal L2 functionality (e.g. limited L2 resources,
         * no RoCE).
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_FLAGS_PREBOOT_MODE \
                UINT32_C(0x1)
        uint8_t unused_0[4];
        /*
         * This bit must be '1' for the qp fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_QP \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the srq fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_SRQ \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the cq fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_CQ \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the vnic fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_VNIC \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the stat fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_STAT \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the tqm_sp fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_SP \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the tqm_ring0 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING0 \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the tqm_ring1 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING1 \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the tqm_ring2 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING2 \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the tqm_ring3 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING3 \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the tqm_ring4 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING4 \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the tqm_ring5 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING5 \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the tqm_ring6 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING6 \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the tqm_ring7 fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TQM_RING7 \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the mrav fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_MRAV \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the tim fields to be
         * configured.
         */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_UNUSED_0_TIM \
                UINT32_C(0x8000)
        /* QPC page size and level. */
        uint8_t qpc_pg_size_qpc_lvl;
        /* QPC PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_LVL_LVL_2
        /* QPC page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_QPC_PG_SIZE_PG_1G
        /* SRQ page size and level. */
        uint8_t srq_pg_size_srq_lvl;
        /* SRQ PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_LVL_LVL_2
        /* SRQ page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_SRQ_PG_SIZE_PG_1G
        /* CQ page size and level. */
        uint8_t cq_pg_size_cq_lvl;
        /* CQ PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_LVL_LVL_2
        /* CQ page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_CQ_PG_SIZE_PG_1G
        /* VNIC page size and level. */
        uint8_t vnic_pg_size_vnic_lvl;
        /* VNIC PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_LVL_LVL_2
        /* VNIC page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_VNIC_PG_SIZE_PG_1G
        /* Stat page size and level. */
        uint8_t stat_pg_size_stat_lvl;
        /* Stat PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_LVL_LVL_2
        /* Stat page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_STAT_PG_SIZE_PG_1G
        /* TQM slow path page size and level. */
        uint8_t tqm_sp_pg_size_tqm_sp_lvl;
        /* TQM slow path PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_LVL_LVL_2
        /* TQM slow path page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_SP_PG_SIZE_PG_1G
        /* TQM ring 0 page size and level. */
        uint8_t tqm_ring0_pg_size_tqm_ring0_lvl;
        /* TQM ring 0 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_LVL_LVL_2
        /* TQM ring 0 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING0_PG_SIZE_PG_1G
        /* TQM ring 1 page size and level. */
        uint8_t tqm_ring1_pg_size_tqm_ring1_lvl;
        /* TQM ring 1 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_LVL_LVL_2
        /* TQM ring 1 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING1_PG_SIZE_PG_1G
        /* TQM ring 2 page size and level. */
        uint8_t tqm_ring2_pg_size_tqm_ring2_lvl;
        /* TQM ring 2 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_LVL_LVL_2
        /* TQM ring 2 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING2_PG_SIZE_PG_1G
        /* TQM ring 3 page size and level. */
        uint8_t tqm_ring3_pg_size_tqm_ring3_lvl;
        /* TQM ring 3 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_LVL_LVL_2
        /* TQM ring 3 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING3_PG_SIZE_PG_1G
        /* TQM ring 4 page size and level. */
        uint8_t tqm_ring4_pg_size_tqm_ring4_lvl;
        /* TQM ring 4 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_LVL_LVL_2
        /* TQM ring 4 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING4_PG_SIZE_PG_1G
        /* TQM ring 5 page size and level. */
        uint8_t tqm_ring5_pg_size_tqm_ring5_lvl;
        /* TQM ring 5 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_LVL_LVL_2
        /* TQM ring 5 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING5_PG_SIZE_PG_1G
        /* TQM ring 6 page size and level. */
        uint8_t tqm_ring6_pg_size_tqm_ring6_lvl;
        /* TQM ring 6 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_LVL_LVL_2
        /* TQM ring 6 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING6_PG_SIZE_PG_1G
        /* TQM ring 7 page size and level. */
        uint8_t tqm_ring7_pg_size_tqm_ring7_lvl;
        /* TQM ring 7 PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_LVL_LVL_2
        /* TQM ring 7 page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TQM_RING7_PG_SIZE_PG_1G
        /* MR/AV page size and level. */
        uint8_t mrav_pg_size_mrav_lvl;
        /* MR/AV PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_LVL_LVL_2
        /* MR/AV page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_MRAV_PG_SIZE_PG_1G
        /* Timer page size and level. */
        uint8_t tim_pg_size_tim_lvl;
        /* Timer PBL indirect levels. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_MASK \
                UINT32_C(0xf)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_SFT       0
        /* PBL pointer is physical start address. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_LVL_0 \
                UINT32_C(0x0)
        /* PBL pointer points to PTE table. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_LVL_1 \
                UINT32_C(0x1)
        /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_LVL_2 \
                UINT32_C(0x2)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_LVL_LVL_2
        /* Timer page size. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_MASK \
                UINT32_C(0xf0)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_SFT   4
        /* 4KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_4K \
                (UINT32_C(0x0) << 4)
        /* 8KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_8K \
                (UINT32_C(0x1) << 4)
        /* 64KB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_64K \
                (UINT32_C(0x2) << 4)
        /* 2MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_2M \
                (UINT32_C(0x3) << 4)
        /* 8MB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_8M \
                (UINT32_C(0x4) << 4)
        /* 1GB. */
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_1G \
                (UINT32_C(0x5) << 4)
        #define HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_LAST \
                HWRM_FUNC_BACKING_STORE_QCFG_OUTPUT_TIM_PG_SIZE_PG_1G
        /* QP page directory. */
        uint64_t        qpc_page_dir;
        /* SRQ page directory. */
        uint64_t        srq_page_dir;
        /* CQ page directory. */
        uint64_t        cq_page_dir;
        /* VNIC page directory. */
        uint64_t        vnic_page_dir;
        /* Stat page directory. */
        uint64_t        stat_page_dir;
        /* TQM slowpath page directory. */
        uint64_t        tqm_sp_page_dir;
        /* TQM ring 0 page directory. */
        uint64_t        tqm_ring0_page_dir;
        /* TQM ring 1 page directory. */
        uint64_t        tqm_ring1_page_dir;
        /* TQM ring 2 page directory. */
        uint64_t        tqm_ring2_page_dir;
        /* TQM ring 3 page directory. */
        uint64_t        tqm_ring3_page_dir;
        /* TQM ring 4 page directory. */
        uint64_t        tqm_ring4_page_dir;
        /* TQM ring 5 page directory. */
        uint64_t        tqm_ring5_page_dir;
        /* TQM ring 6 page directory. */
        uint64_t        tqm_ring6_page_dir;
        /* TQM ring 7 page directory. */
        uint64_t        tqm_ring7_page_dir;
        /* MR/AV page directory. */
        uint64_t        mrav_page_dir;
        /* Timer page directory. */
        uint64_t        tim_page_dir;
        /* Number of entries to reserve for QP1 */
        uint16_t        qp_num_qp1_entries;
        /* Number of entries to reserve for L2 */
        uint16_t        qp_num_l2_entries;
        /* Number of QPs. */
        uint32_t        qp_num_entries;
        /* Number of SRQs. */
        uint32_t        srq_num_entries;
        /* Number of entries to reserve for L2 */
        uint16_t        srq_num_l2_entries;
        /* Number of entries to reserve for L2 */
        uint16_t        cq_num_l2_entries;
        /* Number of CQs. */
        uint32_t        cq_num_entries;
        /* Number of entries to reserve for VNIC entries */
        uint16_t        vnic_num_vnic_entries;
        /* Number of entries to reserve for Ring table entries */
        uint16_t        vnic_num_ring_table_entries;
        /* Number of Stats. */
        uint32_t        stat_num_entries;
        /* Number of TQM slowpath entries. */
        uint32_t        tqm_sp_num_entries;
        /* Number of TQM ring 0 entries. */
        uint32_t        tqm_ring0_num_entries;
        /* Number of TQM ring 1 entries. */
        uint32_t        tqm_ring1_num_entries;
        /* Number of TQM ring 2 entries. */
        uint32_t        tqm_ring2_num_entries;
        /* Number of TQM ring 3 entries. */
        uint32_t        tqm_ring3_num_entries;
        /* Number of TQM ring 4 entries. */
        uint32_t        tqm_ring4_num_entries;
        /* Number of TQM ring 5 entries. */
        uint32_t        tqm_ring5_num_entries;
        /* Number of TQM ring 6 entries. */
        uint32_t        tqm_ring6_num_entries;
        /* Number of TQM ring 7 entries. */
        uint32_t        tqm_ring7_num_entries;
        /* Number of MR/AV entries. */
        uint32_t        mrav_num_entries;
        /* Number of Timer entries. */
        uint32_t        tim_num_entries;
        uint8_t unused_1[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_port_phy_cfg *
 *********************/


/* hwrm_port_phy_cfg_input (size:448b/56B) */
struct hwrm_port_phy_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is set to '1', the PHY for the port shall
         * be reset.
         *
         * # If this bit is set to 1, then the HWRM shall reset the
         * PHY after applying PHY configuration changes specified
         * in this command.
         * # In order to guarantee that PHY configuration changes
         * specified in this command take effect, the HWRM
         * client should set this flag to 1.
         * # If this bit is not set to 1, then the HWRM may reset
         * the PHY depending on the current PHY configuration and
         * settings specified in this command.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY \
                UINT32_C(0x1)
        /* deprecated bit.  Do not use!!! */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_DEPRECATED \
                UINT32_C(0x2)
        /*
         * When this bit is set to '1', the link shall be forced to
         * the force_link_speed value.
         *
         * When this bit is set to '1', the HWRM client should
         * not enable any of the auto negotiation related
         * fields represented by auto_XXX fields in this command.
         * When this bit is set to '1' and the HWRM client has
         * enabled a auto_XXX field in this command, then the
         * HWRM shall ignore the enabled auto_XXX field.
         *
         * When this bit is set to zero, the link
         * shall be allowed to autoneg.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE \
                UINT32_C(0x4)
        /*
         * When this bit is set to '1', the auto-negotiation process
         * shall be restarted on the link.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG \
                UINT32_C(0x8)
        /*
         * When this bit is set to '1', Energy Efficient Ethernet
         * (EEE) is requested to be enabled on this link.
         * If EEE is not supported on this port, then this flag
         * shall be ignored by the HWRM.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE \
                UINT32_C(0x10)
        /*
         * When this bit is set to '1', Energy Efficient Ethernet
         * (EEE) is requested to be disabled on this link.
         * If EEE is not supported on this port, then this flag
         * shall be ignored by the HWRM.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE \
                UINT32_C(0x20)
        /*
         * When this bit is set to '1' and EEE is enabled on this
         * link, then TX LPI is requested to be enabled on the link.
         * If EEE is not supported on this port, then this flag
         * shall be ignored by the HWRM.
         * If EEE is disabled on this port, then this flag shall be
         * ignored by the HWRM.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_ENABLE \
                UINT32_C(0x40)
        /*
         * When this bit is set to '1' and EEE is enabled on this
         * link, then TX LPI is requested to be disabled on the link.
         * If EEE is not supported on this port, then this flag
         * shall be ignored by the HWRM.
         * If EEE is disabled on this port, then this flag shall be
         * ignored by the HWRM.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_DISABLE \
                UINT32_C(0x80)
        /*
         * When set to 1, then the HWRM shall enable FEC autonegotitation
         * on this port if supported.
         * When set to 0, then this flag shall be ignored.
         * If FEC autonegotiation is not supported, then the HWRM shall ignore this
         * flag.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_ENABLE \
                UINT32_C(0x100)
        /*
         * When set to 1, then the HWRM shall disable FEC autonegotiation
         * on this port if supported.
         * When set to 0, then this flag shall be ignored.
         * If FEC autonegotiation is not supported, then the HWRM shall ignore this
         * flag.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_DISABLE \
                UINT32_C(0x200)
        /*
         * When set to 1, then the HWRM shall enable FEC CLAUSE 74 (Fire Code)
         * on this port if supported.
         * When set to 0, then this flag shall be ignored.
         * If FEC CLAUSE 74 is not supported, then the HWRM shall ignore this
         * flag.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_ENABLE \
                UINT32_C(0x400)
        /*
         * When set to 1, then the HWRM shall disable FEC CLAUSE 74 (Fire Code)
         * on this port if supported.
         * When set to 0, then this flag shall be ignored.
         * If FEC CLAUSE 74 is not supported, then the HWRM shall ignore this
         * flag.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_DISABLE \
                UINT32_C(0x800)
        /*
         * When set to 1, then the HWRM shall enable FEC CLAUSE 91 (Reed Solomon)
         * on this port if supported.
         * When set to 0, then this flag shall be ignored.
         * If FEC CLAUSE 91 is not supported, then the HWRM shall ignore this
         * flag.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_ENABLE \
                UINT32_C(0x1000)
        /*
         * When set to 1, then the HWRM shall disable FEC CLAUSE 91 (Reed Solomon)
         * on this port if supported.
         * When set to 0, then this flag shall be ignored.
         * If FEC CLAUSE 91 is not supported, then the HWRM shall ignore this
         * flag.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_DISABLE \
                UINT32_C(0x2000)
        /*
         * When this bit is set to '1', the link shall be forced to
         * be taken down.
         *
         * # When this bit is set to '1", all other
         * command input settings related to the link speed shall
         * be ignored.
         * Once the link state is forced down, it can be
         * explicitly cleared from that state by setting this flag
         * to '0'.
         * # If this flag is set to '0', then the link shall be
         * cleared from forced down state if the link is in forced
         * down state.
         * There may be conditions (e.g. out-of-band or sideband
         * configuration changes for the link) outside the scope
         * of the HWRM implementation that may clear forced down
         * link state.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DWN \
                UINT32_C(0x4000)
        uint32_t        enables;
        /*
         * This bit must be '1' for the auto_mode field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the auto_duplex field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the auto_pause field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the auto_link_speed field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the auto_link_speed_mask field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the wirespeed field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIRESPEED \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the lpbk field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the preemphasis field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the force_pause field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the eee_link_speed_mask field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the tx_lpi_timer field to be
         * configured.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER \
                UINT32_C(0x400)
        /* Port ID of port that is to be configured. */
        uint16_t        port_id;
        /*
         * This is the speed that will be used if the force
         * bit is '1'.  If unsupported speed is selected, an error
         * will be generated.
         */
        uint16_t        force_link_speed;
        /* 100Mb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
        /* 1Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB   UINT32_C(0xa)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB   UINT32_C(0x14)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB  UINT32_C(0x64)
        /* 20Mb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB  UINT32_C(0xc8)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB  UINT32_C(0xfa)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB  UINT32_C(0x190)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB  UINT32_C(0x1f4)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
        /* 10Mb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB  UINT32_C(0xffff)
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_LAST \
                HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB
        /*
         * This value is used to identify what autoneg mode is
         * used when the link speed is not being forced.
         */
        uint8_t auto_mode;
        /* Disable autoneg or autoneg disabled. No speeds are selected. */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE         UINT32_C(0x0)
        /* Select all possible speeds for autoneg mode. */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS   UINT32_C(0x1)
        /*
         * Select only the auto_link_speed speed for autoneg mode. This mode has
         * been DEPRECATED. An HWRM client should not use this mode.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED    UINT32_C(0x2)
        /*
         * Select the auto_link_speed or any speed below that speed for autoneg.
         * This mode has been DEPRECATED. An HWRM client should not use this mode.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
        /*
         * Select the speeds based on the corresponding link speed mask value
         * that is provided.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK   UINT32_C(0x4)
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_LAST \
                HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK
        /*
         * This is the duplex setting that will be used if the autoneg_mode
         * is "one_speed" or "one_or_below".
         */
        uint8_t auto_duplex;
        /* Half Duplex will be requested. */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF UINT32_C(0x0)
        /* Full duplex will be requested. */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL UINT32_C(0x1)
        /* Both Half and Full dupex will be requested. */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH UINT32_C(0x2)
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_LAST \
                HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH
        /*
         * This value is used to configure the pause that will be
         * used for autonegotiation.
         * Add text on the usage of auto_pause and force_pause.
         */
        uint8_t auto_pause;
        /*
         * When this bit is '1', Generation of tx pause messages
         * has been requested. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX \
                UINT32_C(0x1)
        /*
         * When this bit is '1', Reception of rx pause messages
         * has been requested. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX \
                UINT32_C(0x2)
        /*
         * When set to 1, the advertisement of pause is enabled.
         *
         * # When the auto_mode is not set to none and this flag is
         * set to 1, then the auto_pause bits on this port are being
         * advertised and autoneg pause results are being interpreted.
         * # When the auto_mode is not set to none and this
         * flag is set to 0, the pause is forced as indicated in
         * force_pause, and also advertised as auto_pause bits, but
         * the autoneg results are not interpreted since the pause
         * configuration is being forced.
         * # When the auto_mode is set to none and this flag is set to
         * 1, auto_pause bits should be ignored and should be set to 0.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE \
                UINT32_C(0x4)
        uint8_t unused_0;
        /*
         * This is the speed that will be used if the autoneg_mode
         * is "one_speed" or "one_or_below".  If an unsupported speed
         * is selected, an error will be generated.
         */
        uint16_t        auto_link_speed;
        /* 100Mb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
        /* 1Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB   UINT32_C(0xa)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB   UINT32_C(0x14)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB  UINT32_C(0x64)
        /* 20Mb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB  UINT32_C(0xc8)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB  UINT32_C(0xfa)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB  UINT32_C(0x190)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB  UINT32_C(0x1f4)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
        /* 10Mb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB  UINT32_C(0xffff)
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_LAST \
                HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB
        /*
         * This is a mask of link speeds that will be used if
         * autoneg_mode is "mask".  If unsupported speed is enabled
         * an error will be generated.
         */
        uint16_t        auto_link_speed_mask;
        /* 100Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \
                UINT32_C(0x2)
        /* 1Gb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \
                UINT32_C(0x8)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \
                UINT32_C(0x10)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB \
                UINT32_C(0x40)
        /* 20Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB \
                UINT32_C(0x80)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \
                UINT32_C(0x100)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \
                UINT32_C(0x200)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \
                UINT32_C(0x400)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \
                UINT32_C(0x800)
        /* 10Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \
                UINT32_C(0x1000)
        /* 10Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \
                UINT32_C(0x2000)
        /* This value controls the wirespeed feature. */
        uint8_t wirespeed;
        /* Wirespeed feature is disabled. */
        #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_OFF UINT32_C(0x0)
        /* Wirespeed feature is enabled. */
        #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_ON  UINT32_C(0x1)
        #define HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_LAST \
                HWRM_PORT_PHY_CFG_INPUT_WIRESPEED_ON
        /* This value controls the loopback setting for the PHY. */
        uint8_t lpbk;
        /* No loopback is selected.  Normal operation. */
        #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE     UINT32_C(0x0)
        /*
         * The HW will be configured with local loopback such that
         * host data is sent back to the host without modification.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL    UINT32_C(0x1)
        /*
         * The HW will be configured with remote loopback such that
         * port logic will send packets back out the transmitter that
         * are received.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE   UINT32_C(0x2)
        /*
         * The HW will be configured with external loopback such that
         * host data is sent on the trasmitter and based on the external
         * loopback connection the data will be received without modification.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_LPBK_EXTERNAL UINT32_C(0x3)
        #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LAST \
                HWRM_PORT_PHY_CFG_INPUT_LPBK_EXTERNAL
        /*
         * This value is used to configure the pause that will be
         * used for force mode.
         */
        uint8_t force_pause;
        /*
         * When this bit is '1', Generation of tx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX     UINT32_C(0x1)
        /*
         * When this bit is '1', Reception of rx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX     UINT32_C(0x2)
        uint8_t unused_1;
        /*
         * This value controls the pre-emphasis to be used for the
         * link.  Driver should not set this value (use
         * enable.preemphasis = 0) unless driver is sure of setting.
         * Normally HWRM FW will determine proper pre-emphasis.
         */
        uint32_t        preemphasis;
        /*
         * Setting for link speed mask that is used to
         * advertise speeds during autonegotiation when EEE is enabled.
         * This field is valid only when EEE is enabled.
         * The speeds specified in this field shall be a subset of
         * speeds specified in auto_link_speed_mask.
         * If EEE is enabled,then at least one speed shall be provided
         * in this mask.
         */
        uint16_t        eee_link_speed_mask;
        /* Reserved */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB \
                UINT32_C(0x2)
        /* Reserved */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB \
                UINT32_C(0x8)
        /* Reserved */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 \
                UINT32_C(0x10)
        /* Reserved */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB \
                UINT32_C(0x40)
        uint8_t unused_2[2];
        /*
         * Reuested setting of TX LPI timer in microseconds.
         * This field is valid only when EEE is enabled and TX LPI is
         * enabled.
         */
        uint32_t        tx_lpi_timer;
        #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
        #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
        uint32_t        unused_3;
} __attribute__((packed));

/* hwrm_port_phy_cfg_output (size:128b/16B) */
struct hwrm_port_phy_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_port_phy_cfg_cmd_err (size:64b/8B) */
struct hwrm_port_phy_cfg_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_PORT_PHY_CFG_CMD_ERR_CODE_UNKNOWN       UINT32_C(0x0)
        /* Unable to complete operation due to invalid speed */
        #define HWRM_PORT_PHY_CFG_CMD_ERR_CODE_ILLEGAL_SPEED UINT32_C(0x1)
        /*
         * retry the command since the phy is not ready.
         * retry count is returned in opaque_0.
         * This is only valid for the first command and
         * this value will not change for successive calls.
         * but if a 0 is returned at any time then this should
         * be treated as an un recoverable failure,
         *
         * retry interval in milli seconds is returned in opaque_1.
         * This specifies the time that user should wait before
         * issuing the next port_phy_cfg command.
         */
        #define HWRM_PORT_PHY_CFG_CMD_ERR_CODE_RETRY         UINT32_C(0x2)
        #define HWRM_PORT_PHY_CFG_CMD_ERR_CODE_LAST \
                HWRM_PORT_PHY_CFG_CMD_ERR_CODE_RETRY
        uint8_t unused_0[7];
} __attribute__((packed));

/**********************
 * hwrm_port_phy_qcfg *
 **********************/


/* hwrm_port_phy_qcfg_input (size:192b/24B) */
struct hwrm_port_phy_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is to be queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_phy_qcfg_output (size:768b/96B) */
struct hwrm_port_phy_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value indicates the current link status. */
        uint8_t link;
        /* There is no link or cable detected. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK UINT32_C(0x0)
        /* There is no link, but a cable has been detected. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL  UINT32_C(0x1)
        /* There is a link. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK    UINT32_C(0x2)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK
        uint8_t unused_0;
        /* This value indicates the current link speed of the connection. */
        uint16_t        link_speed;
        /* 100Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB UINT32_C(0x1)
        /* 1Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB   UINT32_C(0xa)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB   UINT32_C(0x14)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB UINT32_C(0x19)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB  UINT32_C(0x64)
        /* 20Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB  UINT32_C(0xc8)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB  UINT32_C(0xfa)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB  UINT32_C(0x190)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB  UINT32_C(0x1f4)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB UINT32_C(0x3e8)
        /* 10Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB  UINT32_C(0xffff)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB
        /*
         * This value is indicates the duplex of the current
         * configuration.
         */
        uint8_t duplex_cfg;
        /* Half Duplex connection. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_HALF UINT32_C(0x0)
        /* Full duplex connection. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_FULL UINT32_C(0x1)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_FULL
        /*
         * This value is used to indicate the current
         * pause configuration. When autoneg is enabled, this value
         * represents the autoneg results of pause configuration.
         */
        uint8_t pause;
        /*
         * When this bit is '1', Generation of tx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX     UINT32_C(0x1)
        /*
         * When this bit is '1', Reception of rx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX     UINT32_C(0x2)
        /*
         * The supported speeds for the port. This is a bit mask.
         * For each speed that is supported, the corrresponding
         * bit will be set to '1'.
         */
        uint16_t        support_speeds;
        /* 100Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB \
                UINT32_C(0x2)
        /* 1Gb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB \
                UINT32_C(0x8)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB \
                UINT32_C(0x10)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB \
                UINT32_C(0x40)
        /* 20Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB \
                UINT32_C(0x80)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB \
                UINT32_C(0x100)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB \
                UINT32_C(0x200)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB \
                UINT32_C(0x400)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB \
                UINT32_C(0x800)
        /* 10Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD \
                UINT32_C(0x1000)
        /* 10Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB \
                UINT32_C(0x2000)
        /*
         * Current setting of forced link speed.
         * When the link speed is not being forced, this
         * value shall be set to 0.
         */
        uint16_t        force_link_speed;
        /* 100Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
        /* 1Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB   UINT32_C(0xa)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB   UINT32_C(0x14)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB  UINT32_C(0x64)
        /* 20Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB  UINT32_C(0xc8)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB  UINT32_C(0xfa)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB \
                UINT32_C(0x190)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB \
                UINT32_C(0x1f4)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB \
                UINT32_C(0x3e8)
        /* 10Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB \
                UINT32_C(0xffff)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB
        /* Current setting of auto negotiation mode. */
        uint8_t auto_mode;
        /* Disable autoneg or autoneg disabled. No speeds are selected. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE         UINT32_C(0x0)
        /* Select all possible speeds for autoneg mode. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS   UINT32_C(0x1)
        /*
         * Select only the auto_link_speed speed for autoneg mode. This mode has
         * been DEPRECATED. An HWRM client should not use this mode.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED    UINT32_C(0x2)
        /*
         * Select the auto_link_speed or any speed below that speed for autoneg.
         * This mode has been DEPRECATED. An HWRM client should not use this mode.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
        /*
         * Select the speeds based on the corresponding link speed mask value
         * that is provided.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK   UINT32_C(0x4)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK
        /*
         * Current setting of pause autonegotiation.
         * Move autoneg_pause flag here.
         */
        uint8_t auto_pause;
        /*
         * When this bit is '1', Generation of tx pause messages
         * has been requested. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX \
                UINT32_C(0x1)
        /*
         * When this bit is '1', Reception of rx pause messages
         * has been requested. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX \
                UINT32_C(0x2)
        /*
         * When set to 1, the advertisement of pause is enabled.
         *
         * # When the auto_mode is not set to none and this flag is
         * set to 1, then the auto_pause bits on this port are being
         * advertised and autoneg pause results are being interpreted.
         * # When the auto_mode is not set to none and this
         * flag is set to 0, the pause is forced as indicated in
         * force_pause, and also advertised as auto_pause bits, but
         * the autoneg results are not interpreted since the pause
         * configuration is being forced.
         * # When the auto_mode is set to none and this flag is set to
         * 1, auto_pause bits should be ignored and should be set to 0.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE \
                UINT32_C(0x4)
        /*
         * Current setting for auto_link_speed. This field is only
         * valid when auto_mode is set to "one_speed" or "one_or_below".
         */
        uint16_t        auto_link_speed;
        /* 100Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
        /* 1Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB   UINT32_C(0xa)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB   UINT32_C(0x14)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB  UINT32_C(0x64)
        /* 20Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB  UINT32_C(0xc8)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB  UINT32_C(0xfa)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB  UINT32_C(0x190)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB  UINT32_C(0x1f4)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
        /* 10Mb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB \
                UINT32_C(0xffff)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB
        /*
         * Current setting for auto_link_speed_mask that is used to
         * advertise speeds during autonegotiation.
         * This field is only valid when auto_mode is set to "mask".
         * The speeds specified in this field shall be a subset of
         * supported speeds on this port.
         */
        uint16_t        auto_link_speed_mask;
        /* 100Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB \
                UINT32_C(0x2)
        /* 1Gb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB \
                UINT32_C(0x8)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB \
                UINT32_C(0x10)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB \
                UINT32_C(0x40)
        /* 20Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB \
                UINT32_C(0x80)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB \
                UINT32_C(0x100)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB \
                UINT32_C(0x200)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB \
                UINT32_C(0x400)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB \
                UINT32_C(0x800)
        /* 10Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD \
                UINT32_C(0x1000)
        /* 10Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB \
                UINT32_C(0x2000)
        /* Current setting for wirespeed. */
        uint8_t wirespeed;
        /* Wirespeed feature is disabled. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_OFF UINT32_C(0x0)
        /* Wirespeed feature is enabled. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_ON  UINT32_C(0x1)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_WIRESPEED_ON
        /* Current setting for loopback. */
        uint8_t lpbk;
        /* No loopback is selected.  Normal operation. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE     UINT32_C(0x0)
        /*
         * The HW will be configured with local loopback such that
         * host data is sent back to the host without modification.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL    UINT32_C(0x1)
        /*
         * The HW will be configured with remote loopback such that
         * port logic will send packets back out the transmitter that
         * are received.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE   UINT32_C(0x2)
        /*
         * The HW will be configured with external loopback such that
         * host data is sent on the trasmitter and based on the external
         * loopback connection the data will be received without modification.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_EXTERNAL UINT32_C(0x3)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_EXTERNAL
        /*
         * Current setting of forced pause.
         * When the pause configuration is not being forced, then
         * this value shall be set to 0.
         */
        uint8_t force_pause;
        /*
         * When this bit is '1', Generation of tx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX     UINT32_C(0x1)
        /*
         * When this bit is '1', Reception of rx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX     UINT32_C(0x2)
        /*
         * This value indicates the current status of the optics module on
         * this port.
         */
        uint8_t module_status;
        /* Module is inserted and accepted */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE \
                UINT32_C(0x0)
        /* Module is rejected and transmit side Laser is disabled. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX \
                UINT32_C(0x1)
        /* Module mismatch warning. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG \
                UINT32_C(0x2)
        /* Module is rejected and powered down. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN \
                UINT32_C(0x3)
        /* Module is not inserted. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED \
                UINT32_C(0x4)
        /* Module status is not applicable. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE \
                UINT32_C(0xff)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE
        /* Current setting for preemphasis. */
        uint32_t        preemphasis;
        /* This field represents the major version of the PHY. */
        uint8_t phy_maj;
        /* This field represents the minor version of the PHY. */
        uint8_t phy_min;
        /* This field represents the build version of the PHY. */
        uint8_t phy_bld;
        /* This value represents a PHY type. */
        uint8_t phy_type;
        /* Unknown */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN \
                UINT32_C(0x0)
        /* BASE-CR */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR \
                UINT32_C(0x1)
        /* BASE-KR4 (Deprecated) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 \
                UINT32_C(0x2)
        /* BASE-LR */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR \
                UINT32_C(0x3)
        /* BASE-SR */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR \
                UINT32_C(0x4)
        /* BASE-KR2 (Deprecated) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 \
                UINT32_C(0x5)
        /* BASE-KX */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX \
                UINT32_C(0x6)
        /* BASE-KR */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR \
                UINT32_C(0x7)
        /* BASE-T */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET \
                UINT32_C(0x8)
        /* EEE capable BASE-T */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE \
                UINT32_C(0x9)
        /* SGMII connected external PHY */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY \
                UINT32_C(0xa)
        /* 25G_BASECR_CA_L */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_L \
                UINT32_C(0xb)
        /* 25G_BASECR_CA_S */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_S \
                UINT32_C(0xc)
        /* 25G_BASECR_CA_N */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_N \
                UINT32_C(0xd)
        /* 25G_BASESR */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASESR \
                UINT32_C(0xe)
        /* 100G_BASECR4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASECR4 \
                UINT32_C(0xf)
        /* 100G_BASESR4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR4 \
                UINT32_C(0x10)
        /* 100G_BASELR4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASELR4 \
                UINT32_C(0x11)
        /* 100G_BASEER4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASEER4 \
                UINT32_C(0x12)
        /* 100G_BASESR10 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR10 \
                UINT32_C(0x13)
        /* 40G_BASECR4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASECR4 \
                UINT32_C(0x14)
        /* 40G_BASESR4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASESR4 \
                UINT32_C(0x15)
        /* 40G_BASELR4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASELR4 \
                UINT32_C(0x16)
        /* 40G_BASEER4 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASEER4 \
                UINT32_C(0x17)
        /* 40G_ACTIVE_CABLE */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_ACTIVE_CABLE \
                UINT32_C(0x18)
        /* 1G_baseT */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASET \
                UINT32_C(0x19)
        /* 1G_baseSX */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASESX \
                UINT32_C(0x1a)
        /* 1G_baseCX */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASECX \
                UINT32_C(0x1b)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASECX
        /* This value represents a media type. */
        uint8_t media_type;
        /* Unknown */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN UINT32_C(0x0)
        /* Twisted Pair */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP      UINT32_C(0x1)
        /* Direct Attached Copper */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC     UINT32_C(0x2)
        /* Fiber */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE   UINT32_C(0x3)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE
        /* This value represents a transceiver type. */
        uint8_t xcvr_pkg_type;
        /* PHY and MAC are in the same package */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL \
                UINT32_C(0x1)
        /* PHY and MAC are in different packages */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL \
                UINT32_C(0x2)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL
        uint8_t eee_config_phy_addr;
        /* This field represents PHY address. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK \
                UINT32_C(0x1f)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT               0
        /*
         * This field represents flags related to EEE configuration.
         * These EEE configuration flags are valid only when the
         * auto_mode is not set to none (in other words autonegotiation
         * is enabled).
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK \
                UINT32_C(0xe0)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT             5
        /*
         * When set to 1, Energy Efficient Ethernet (EEE) mode is enabled.
         * Speeds for autoneg with EEE mode enabled
         * are based on eee_link_speed_mask.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED \
                UINT32_C(0x20)
        /*
         * This flag is valid only when eee_enabled is set to 1.
         *
         * # If eee_enabled is set to 0, then EEE mode is disabled
         * and this flag shall be ignored.
         * # If eee_enabled is set to 1 and this flag is set to 1,
         * then Energy Efficient Ethernet (EEE) mode is enabled
         * and in use.
         * # If eee_enabled is set to 1 and this flag is set to 0,
         * then Energy Efficient Ethernet (EEE) mode is enabled
         * but is currently not in use.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE \
                UINT32_C(0x40)
        /*
         * This flag is valid only when eee_enabled is set to 1.
         *
         * # If eee_enabled is set to 0, then EEE mode is disabled
         * and this flag shall be ignored.
         * # If eee_enabled is set to 1 and this flag is set to 1,
         * then Energy Efficient Ethernet (EEE) mode is enabled
         * and TX LPI is enabled.
         * # If eee_enabled is set to 1 and this flag is set to 0,
         * then Energy Efficient Ethernet (EEE) mode is enabled
         * but TX LPI is disabled.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI \
                UINT32_C(0x80)
        /*
         * When set to 1, the parallel detection is used to determine
         * the speed of the link partner.
         *
         * Parallel detection is used when a autonegotiation capable
         * device is connected to a link parter that is not capable
         * of autonegotiation.
         */
        uint8_t parallel_detect;
        /*
         * When set to 1, the parallel detection is used to determine
         * the speed of the link partner.
         *
         * Parallel detection is used when a autonegotiation capable
         * device is connected to a link parter that is not capable
         * of autonegotiation.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT     UINT32_C(0x1)
        /*
         * The advertised speeds for the port by the link partner.
         * Each advertised speed will be set to '1'.
         */
        uint16_t        link_partner_adv_speeds;
        /* 100Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \
                UINT32_C(0x2)
        /* 1Gb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \
                UINT32_C(0x8)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \
                UINT32_C(0x10)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \
                UINT32_C(0x40)
        /* 20Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \
                UINT32_C(0x80)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \
                UINT32_C(0x100)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \
                UINT32_C(0x200)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \
                UINT32_C(0x400)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \
                UINT32_C(0x800)
        /* 10Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \
                UINT32_C(0x1000)
        /* 10Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \
                UINT32_C(0x2000)
        /*
         * The advertised autoneg for the port by the link partner.
         * This field is deprecated and should be set to 0.
         */
        uint8_t link_partner_adv_auto_mode;
        /* Disable autoneg or autoneg disabled. No speeds are selected. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \
                UINT32_C(0x0)
        /* Select all possible speeds for autoneg mode. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
                UINT32_C(0x1)
        /*
         * Select only the auto_link_speed speed for autoneg mode. This mode has
         * been DEPRECATED. An HWRM client should not use this mode.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
                UINT32_C(0x2)
        /*
         * Select the auto_link_speed or any speed below that speed for autoneg.
         * This mode has been DEPRECATED. An HWRM client should not use this mode.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
                UINT32_C(0x3)
        /*
         * Select the speeds based on the corresponding link speed mask value
         * that is provided.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
                UINT32_C(0x4)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK
        /* The advertised pause settings on the port by the link partner. */
        uint8_t link_partner_adv_pause;
        /*
         * When this bit is '1', Generation of tx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
                UINT32_C(0x1)
        /*
         * When this bit is '1', Reception of rx pause messages
         * is supported. Disabled otherwise.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
                UINT32_C(0x2)
        /*
         * Current setting for link speed mask that is used to
         * advertise speeds during autonegotiation when EEE is enabled.
         * This field is valid only when eee_enabled flags is set to 1.
         * The speeds specified in this field shall be a subset of
         * speeds specified in auto_link_speed_mask.
         */
        uint16_t        adv_eee_link_speed_mask;
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
                UINT32_C(0x2)
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
                UINT32_C(0x8)
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
                UINT32_C(0x10)
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
                UINT32_C(0x40)
        /*
         * Current setting for link speed mask that is advertised by
         * the link partner when EEE is enabled.
         * This field is valid only when eee_enabled flags is set to 1.
         */
        uint16_t        link_partner_adv_eee_link_speed_mask;
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
                UINT32_C(0x2)
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
                UINT32_C(0x8)
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
                UINT32_C(0x10)
        /* Reserved */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
                UINT32_C(0x40)
        uint32_t        xcvr_identifier_type_tx_lpi_timer;
        /*
         * Current setting of TX LPI timer in microseconds.
         * This field is valid only when_eee_enabled flag is set to 1
         * and tx_lpi_enabled is set to 1.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK \
                UINT32_C(0xffffff)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT             0
        /* This value represents transceiver identifier type. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
                UINT32_C(0xff000000)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT     24
        /* Unknown */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
                (UINT32_C(0x0) << 24)
        /* SFP/SFP+/SFP28 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
                (UINT32_C(0x3) << 24)
        /* QSFP+ */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
                (UINT32_C(0xc) << 24)
        /* QSFP+ */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
                (UINT32_C(0xd) << 24)
        /* QSFP28 */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
                (UINT32_C(0x11) << 24)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28
        /*
         * This value represents the current configuration of
         * Forward Error Correction (FEC) on the port.
         */
        uint16_t        fec_cfg;
        /*
         * When set to 1, then FEC is not supported on this port. If this flag
         * is set to 1, then all other FEC configuration flags shall be ignored.
         * When set to 0, then FEC is supported as indicated by other
         * configuration flags.
         * If no cable is attached and the HWRM does not yet know the FEC
         * capability, then the HWRM shall set this flag to 1 when reporting
         * FEC capability.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED \
                UINT32_C(0x1)
        /*
         * When set to 1, then FEC autonegotiation is supported on this port.
         * When set to 0, then FEC autonegotiation is not supported on this port.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED \
                UINT32_C(0x2)
        /*
         * When set to 1, then FEC autonegotiation is enabled on this port.
         * When set to 0, then FEC autonegotiation is disabled if supported.
         * This flag should be ignored if FEC autonegotiation is not supported on this port.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED \
                UINT32_C(0x4)
        /*
         * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on this port.
         * When set to 0, then FEC CLAUSE 74 (Fire Code) is not supported on this port.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED \
                UINT32_C(0x8)
        /*
         * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on this port.
         * When set to 0, then FEC CLAUSE 74 (Fire Code) is disabled if supported.
         * This flag should be ignored if FEC CLAUSE 74 is not supported on this port.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED \
                UINT32_C(0x10)
        /*
         * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is supported on this port.
         * When set to 0, then FEC CLAUSE 91 (Reed Solomon) is not supported on this port.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED \
                UINT32_C(0x20)
        /*
         * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is enabled on this port.
         * When set to 0, then FEC CLAUSE 91 (Reed Solomon) is disabled if supported.
         * This flag should be ignored if FEC CLAUSE 91 is not supported on this port.
         */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED \
                UINT32_C(0x40)
        /*
         * This value is indicates the duplex of the current
         * connection state.
         */
        uint8_t duplex_state;
        /* Half Duplex connection. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_HALF UINT32_C(0x0)
        /* Full duplex connection. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_FULL UINT32_C(0x1)
        #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_LAST \
                HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_FULL
        /* Option flags fields. */
        uint8_t option_flags;
        /* When this bit is '1', Media auto detect is enabled. */
        #define HWRM_PORT_PHY_QCFG_OUTPUT_OPTION_FLAGS_MEDIA_AUTO_DETECT \
                UINT32_C(0x1)
        /*
         * Up to 16 bytes of null padded ASCII string representing
         * PHY vendor.
         * If the string is set to null, then the vendor name is not
         * available.
         */
        char    phy_vendor_name[16];
        /*
         * Up to 16 bytes of null padded ASCII string that
         * identifies vendor specific part number of the PHY.
         * If the string is set to null, then the vendor specific
         * part number is not available.
         */
        char    phy_vendor_partnumber[16];
        uint8_t unused_2[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_port_mac_cfg *
 *********************/


/* hwrm_port_mac_cfg_input (size:320b/40B) */
struct hwrm_port_mac_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * In this field, there are a number of CoS mappings related flags
         * that are used to configure CoS mappings and their corresponding
         * priorities in the hardware.
         * For the priorities of CoS mappings, the HWRM uses the following
         * priority order (high to low) by default:
         * # vlan pri
         * # ip_dscp
         * # tunnel_vlan_pri
         * # default cos
         *
         * A subset of CoS mappings can be enabled.
         * If a priority is not specified for an enabled CoS mapping, the
         * priority will be assigned in the above order for the enabled CoS
         * mappings. For example, if vlan_pri and ip_dscp CoS mappings are
         * enabled and their priorities are not specified, the following
         * priority order (high to low) will be used by the HWRM:
         * # vlan_pri
         * # ip_dscp
         * # default cos
         *
         * vlan_pri CoS mapping together with default CoS with lower priority
         * are enabled by default by the HWRM.
         */
        uint32_t        flags;
        /*
         * When this bit is '1', this command will configure
         * the MAC to match the current link state of the PHY.
         * If the link is not established on the PHY, then this
         * bit has no effect.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_MATCH_LINK \
                UINT32_C(0x1)
        /*
         * When this bit is set to '1', the inner VLAN PRI to CoS mapping
         * is requested to be enabled.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_VLAN_PRI2COS_ENABLE \
                UINT32_C(0x2)
        /*
         * When this bit is set to '1', tunnel VLAN PRI field to
         * CoS mapping is requested to be enabled.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_TUNNEL_PRI2COS_ENABLE \
                UINT32_C(0x4)
        /*
         * When this bit is set to '1', the IP DSCP to CoS mapping is
         * requested to be enabled.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_IP_DSCP2COS_ENABLE \
                UINT32_C(0x8)
        /*
         * When this bit is '1', the HWRM is requested to
         * enable timestamp capture capability on the receive side
         * of this port.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_RX_TS_CAPTURE_ENABLE \
                UINT32_C(0x10)
        /*
         * When this bit is '1', the HWRM is requested to
         * disable timestamp capture capability on the receive side
         * of this port.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_RX_TS_CAPTURE_DISABLE \
                UINT32_C(0x20)
        /*
         * When this bit is '1', the HWRM is requested to
         * enable timestamp capture capability on the transmit side
         * of this port.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_TX_TS_CAPTURE_ENABLE \
                UINT32_C(0x40)
        /*
         * When this bit is '1', the HWRM is requested to
         * disable timestamp capture capability on the transmit side
         * of this port.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_TX_TS_CAPTURE_DISABLE \
                UINT32_C(0x80)
        /*
         * When this bit is '1', the Out-Of-Box WoL is requested to
         * be enabled on this port.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_OOB_WOL_ENABLE \
                UINT32_C(0x100)
        /*
         * When this bit is '1', the the Out-Of-Box WoL is requested to
         * be disabled on this port.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_OOB_WOL_DISABLE \
                UINT32_C(0x200)
        /*
         * When this bit is set to '1', the inner VLAN PRI to CoS mapping
         * is requested to be disabled.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_VLAN_PRI2COS_DISABLE \
                UINT32_C(0x400)
        /*
         * When this bit is set to '1', tunnel VLAN PRI field to
         * CoS mapping is requested to be disabled.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_TUNNEL_PRI2COS_DISABLE \
                UINT32_C(0x800)
        /*
         * When this bit is set to '1', the IP DSCP to CoS mapping is
         * requested to be disabled.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_IP_DSCP2COS_DISABLE \
                UINT32_C(0x1000)
        uint32_t        enables;
        /*
         * This bit must be '1' for the ipg field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_IPG \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the lpbk field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_LPBK \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the vlan_pri2cos_map_pri field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_VLAN_PRI2COS_MAP_PRI \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the tunnel_pri2cos_map_pri field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_TUNNEL_PRI2COS_MAP_PRI \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the dscp2cos_map_pri field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_DSCP2COS_MAP_PRI \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the rx_ts_capture_ptp_msg_type field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_RX_TS_CAPTURE_PTP_MSG_TYPE \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the tx_ts_capture_ptp_msg_type field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_TX_TS_CAPTURE_PTP_MSG_TYPE \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the cos_field_cfg field to be
         * configured.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_COS_FIELD_CFG \
                UINT32_C(0x100)
        /* Port ID of port that is to be configured. */
        uint16_t        port_id;
        /*
         * This value is used to configure the minimum IPG that will
         * be sent between packets by this port.
         */
        uint8_t ipg;
        /* This value controls the loopback setting for the MAC. */
        uint8_t lpbk;
        /* No loopback is selected.  Normal operation. */
        #define HWRM_PORT_MAC_CFG_INPUT_LPBK_NONE   UINT32_C(0x0)
        /*
         * The HW will be configured with local loopback such that
         * host data is sent back to the host without modification.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_LPBK_LOCAL  UINT32_C(0x1)
        /*
         * The HW will be configured with remote loopback such that
         * port logic will send packets back out the transmitter that
         * are received.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_LPBK_REMOTE UINT32_C(0x2)
        #define HWRM_PORT_MAC_CFG_INPUT_LPBK_LAST \
                HWRM_PORT_MAC_CFG_INPUT_LPBK_REMOTE
        /*
         * This value controls the priority setting of VLAN PRI to CoS
         * mapping based on VLAN Tags of inner packet headers of
         * tunneled packets or packet headers of non-tunneled packets.
         *
         * # Each XXX_pri variable shall have a unique priority value
         * when it is being specified.
         * # When comparing priorities of mappings, higher value
         * indicates higher priority.
         * For example, a value of 0-3 is returned where 0 is being
         * the lowest priority and 3 is being the highest priority.
         */
        uint8_t vlan_pri2cos_map_pri;
        /* Reserved field. */
        uint8_t reserved1;
        /*
         * This value controls the priority setting of VLAN PRI to CoS
         * mapping based on VLAN Tags of tunneled header.
         * This mapping only applies when tunneled headers
         * are present.
         *
         * # Each XXX_pri variable shall have a unique priority value
         * when it is being specified.
         * # When comparing priorities of mappings, higher value
         * indicates higher priority.
         * For example, a value of 0-3 is returned where 0 is being
         * the lowest priority and 3 is being the highest priority.
         */
        uint8_t tunnel_pri2cos_map_pri;
        /*
         * This value controls the priority setting of IP DSCP to CoS
         * mapping based on inner IP header of tunneled packets or
         * IP header of non-tunneled packets.
         *
         * # Each XXX_pri variable shall have a unique priority value
         * when it is being specified.
         * # When comparing priorities of mappings, higher value
         * indicates higher priority.
         * For example, a value of 0-3 is returned where 0 is being
         * the lowest priority and 3 is being the highest priority.
         */
        uint8_t dscp2pri_map_pri;
        /*
         * This is a 16-bit bit mask that is used to request a
         * specific configuration of time stamp capture of PTP messages
         * on the receive side of this port.
         * This field shall be ignored if the ptp_rx_ts_capture_enable
         * flag is not set in this command.
         * Otherwise, if bit 'i' is set, then the HWRM is being
         * requested to configure the receive side of the port to
         * capture the time stamp of every received PTP message
         * with messageType field value set to i.
         */
        uint16_t        rx_ts_capture_ptp_msg_type;
        /*
         * This is a 16-bit bit mask that is used to request a
         * specific configuration of time stamp capture of PTP messages
         * on the transmit side of this port.
         * This field shall be ignored if the ptp_tx_ts_capture_enable
         * flag is not set in this command.
         * Otherwise, if bit 'i' is set, then the HWRM is being
         * requested to configure the transmit sied of the port to
         * capture the time stamp of every transmitted PTP message
         * with messageType field value set to i.
         */
        uint16_t        tx_ts_capture_ptp_msg_type;
        /* Configuration of CoS fields. */
        uint8_t cos_field_cfg;
        /* Reserved */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_RSVD1 \
                UINT32_C(0x1)
        /*
         * This field is used to specify selection of VLAN PRI value
         * based on whether one or two VLAN Tags are present in
         * the inner packet headers of tunneled packets or
         * non-tunneled packets.
         * This field is valid only if inner VLAN PRI to CoS mapping
         * is enabled.
         * If VLAN PRI to CoS mapping is not enabled, then this
         * field shall be ignored.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_MASK \
                UINT32_C(0x6)
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_SFT \
                1
        /*
         * Select inner VLAN PRI when 1 or 2 VLAN Tags are
         * present in the inner packet headers
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_INNERMOST \
                (UINT32_C(0x0) << 1)
        /*
         * Select outer VLAN Tag PRI when 2 VLAN Tags are
         * present in the inner packet headers.
         * No VLAN PRI shall be selected for this configuration
         * if only one VLAN Tag is present in the inner
         * packet headers.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTER \
                (UINT32_C(0x1) << 1)
        /*
         * Select outermost VLAN PRI when 1 or 2 VLAN Tags
         * are present in the inner packet headers
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTERMOST \
                (UINT32_C(0x2) << 1)
        /* Unspecified */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED \
                (UINT32_C(0x3) << 1)
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_LAST \
                HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED
        /*
         * This field is used to specify selection of tunnel VLAN
         * PRI value based on whether one or two VLAN Tags are
         * present in tunnel headers.
         * This field is valid only if tunnel VLAN PRI to CoS mapping
         * is enabled.
         * If tunnel VLAN PRI to CoS mapping is not enabled, then this
         * field shall be ignored.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_MASK \
                UINT32_C(0x18)
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_SFT \
                3
        /*
         * Select inner VLAN PRI when 1 or 2 VLAN Tags are
         * present in the tunnel packet headers
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_INNERMOST \
                (UINT32_C(0x0) << 3)
        /*
         * Select outer VLAN Tag PRI when 2 VLAN Tags are
         * present in the tunnel packet headers.
         * No tunnel VLAN PRI shall be selected for this
         * configuration if only one VLAN Tag is present in
         * the tunnel packet headers.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTER \
                (UINT32_C(0x1) << 3)
        /*
         * Select outermost VLAN PRI when 1 or 2 VLAN Tags
         * are present in the tunnel packet headers
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTERMOST \
                (UINT32_C(0x2) << 3)
        /* Unspecified */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED \
                (UINT32_C(0x3) << 3)
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_LAST \
                HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED
        /*
         * This field shall be used to provide default CoS value
         * that has been configured on this port.
         * This field is valid only if default CoS mapping
         * is enabled.
         * If default CoS mapping is not enabled, then this
         * field shall be ignored.
         */
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_DEFAULT_COS_MASK \
                UINT32_C(0xe0)
        #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_DEFAULT_COS_SFT \
                5
        uint8_t unused_0[3];
} __attribute__((packed));

/* hwrm_port_mac_cfg_output (size:128b/16B) */
struct hwrm_port_mac_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This is the configured maximum length of Ethernet packet
         * payload that is allowed to be received on the port.
         * This value does not include the number of bytes used by
         * Ethernet header and trailer (CRC).
         */
        uint16_t        mru;
        /*
         * This is the configured maximum length of Ethernet packet
         * payload that is allowed to be transmitted on the port.
         * This value does not include the number of bytes used by
         * Ethernet header and trailer (CRC).
         */
        uint16_t        mtu;
        /* Current configuration of the IPG value. */
        uint8_t ipg;
        /* Current value of the loopback value. */
        uint8_t lpbk;
        /* No loopback is selected.  Normal operation. */
        #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_NONE   UINT32_C(0x0)
        /*
         * The HW will be configured with local loopback such that
         * host data is sent back to the host without modification.
         */
        #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_LOCAL  UINT32_C(0x1)
        /*
         * The HW will be configured with remote loopback such that
         * port logic will send packets back out the transmitter that
         * are received.
         */
        #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
        #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_LAST \
                HWRM_PORT_MAC_CFG_OUTPUT_LPBK_REMOTE
        uint8_t unused_0;
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_port_mac_qcfg *
 **********************/


/* hwrm_port_mac_qcfg_input (size:192b/24B) */
struct hwrm_port_mac_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is to be configured. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_mac_qcfg_output (size:192b/24B) */
struct hwrm_port_mac_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This is the configured maximum length of Ethernet packet
         * payload that is allowed to be received on the port.
         * This value does not include the number of bytes used by the
         * Ethernet header and trailer (CRC).
         */
        uint16_t        mru;
        /*
         * This is the configured maximum length of Ethernet packet
         * payload that is allowed to be transmitted on the port.
         * This value does not include the number of bytes used by the
         * Ethernet header and trailer (CRC).
         */
        uint16_t        mtu;
        /*
         * The minimum IPG that will
         * be sent between packets by this port.
         */
        uint8_t ipg;
        /* The loopback setting for the MAC. */
        uint8_t lpbk;
        /* No loopback is selected.  Normal operation. */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_NONE   UINT32_C(0x0)
        /*
         * The HW will be configured with local loopback such that
         * host data is sent back to the host without modification.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_LOCAL  UINT32_C(0x1)
        /*
         * The HW will be configured with remote loopback such that
         * port logic will send packets back out the transmitter that
         * are received.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
        #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_LAST \
                HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_REMOTE
        /*
         * Priority setting for VLAN PRI to CoS mapping.
         * # Each XXX_pri variable shall have a unique priority value
         * when it is being used.
         * # When comparing priorities of mappings, higher value
         * indicates higher priority.
         * For example, a value of 0-3 is returned where 0 is being
         * the lowest priority and 3 is being the highest priority.
         * # If the correspoding CoS mapping is not enabled, then this
         * field should be ignored.
         * # This value indicates the normalized priority value retained
         * in the HWRM.
         */
        uint8_t vlan_pri2cos_map_pri;
        /*
         * In this field, a number of CoS mappings related flags
         * are used to indicate configured CoS mappings.
         */
        uint8_t flags;
        /*
         * When this bit is set to '1', the inner VLAN PRI to CoS mapping
         * is enabled.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_VLAN_PRI2COS_ENABLE \
                UINT32_C(0x1)
        /*
         * When this bit is set to '1', tunnel VLAN PRI field to
         * CoS mapping is enabled.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_TUNNEL_PRI2COS_ENABLE \
                UINT32_C(0x2)
        /*
         * When this bit is set to '1', the IP DSCP to CoS mapping is
         * enabled.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_IP_DSCP2COS_ENABLE \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the Out-Of-Box WoL is enabled on this
         * port.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_OOB_WOL_ENABLE \
                UINT32_C(0x8)
        /* When this bit is '1', PTP is enabled for RX on this port. */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_PTP_RX_TS_CAPTURE_ENABLE \
                UINT32_C(0x10)
        /* When this bit is '1', PTP is enabled for TX on this port. */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_PTP_TX_TS_CAPTURE_ENABLE \
                UINT32_C(0x20)
        /*
         * Priority setting for tunnel VLAN PRI to CoS mapping.
         * # Each XXX_pri variable shall have a unique priority value
         * when it is being used.
         * # When comparing priorities of mappings, higher value
         * indicates higher priority.
         * For example, a value of 0-3 is returned where 0 is being
         * the lowest priority and 3 is being the highest priority.
         * # If the correspoding CoS mapping is not enabled, then this
         * field should be ignored.
         * # This value indicates the normalized priority value retained
         * in the HWRM.
         */
        uint8_t tunnel_pri2cos_map_pri;
        /*
         * Priority setting for DSCP to PRI mapping.
         * # Each XXX_pri variable shall have a unique priority value
         * when it is being used.
         * # When comparing priorities of mappings, higher value
         * indicates higher priority.
         * For example, a value of 0-3 is returned where 0 is being
         * the lowest priority and 3 is being the highest priority.
         * # If the correspoding CoS mapping is not enabled, then this
         * field should be ignored.
         * # This value indicates the normalized priority value retained
         * in the HWRM.
         */
        uint8_t dscp2pri_map_pri;
        /*
         * This is a 16-bit bit mask that represents the
         * current configuration of time stamp capture of PTP messages
         * on the receive side of this port.
         * If bit 'i' is set, then the receive side of the port
         * is configured to capture the time stamp of every
         * received PTP message with messageType field value set
         * to i.
         * If all bits are set to 0 (i.e. field value set 0),
         * then the receive side of the port is not configured
         * to capture timestamp for PTP messages.
         * If all bits are set to 1, then the receive side of the
         * port is configured to capture timestamp for all PTP
         * messages.
         */
        uint16_t        rx_ts_capture_ptp_msg_type;
        /*
         * This is a 16-bit bit mask that represents the
         * current configuration of time stamp capture of PTP messages
         * on the transmit side of this port.
         * If bit 'i' is set, then the transmit side of the port
         * is configured to capture the time stamp of every
         * received PTP message with messageType field value set
         * to i.
         * If all bits are set to 0 (i.e. field value set 0),
         * then the transmit side of the port is not configured
         * to capture timestamp for PTP messages.
         * If all bits are set to 1, then the transmit side of the
         * port is configured to capture timestamp for all PTP
         * messages.
         */
        uint16_t        tx_ts_capture_ptp_msg_type;
        /* Configuration of CoS fields. */
        uint8_t cos_field_cfg;
        /* Reserved */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_RSVD \
                UINT32_C(0x1)
        /*
         * This field is used for selecting VLAN PRI value
         * based on whether one or two VLAN Tags are present in
         * the inner packet headers of tunneled packets or
         * non-tunneled packets.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_MASK \
                UINT32_C(0x6)
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_SFT \
                1
        /*
         * Select inner VLAN PRI when 1 or 2 VLAN Tags are
         * present in the inner packet headers
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_INNERMOST \
                (UINT32_C(0x0) << 1)
        /*
         * Select outer VLAN Tag PRI when 2 VLAN Tags are
         * present in the inner packet headers.
         * No VLAN PRI is selected for this configuration
         * if only one VLAN Tag is present in the inner
         * packet headers.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTER \
                (UINT32_C(0x1) << 1)
        /*
         * Select outermost VLAN PRI when 1 or 2 VLAN Tags
         * are present in the inner packet headers
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTERMOST \
                (UINT32_C(0x2) << 1)
        /* Unspecified */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED \
                (UINT32_C(0x3) << 1)
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_LAST \
                HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED
        /*
         * This field is used for selecting tunnel VLAN PRI value
         * based on whether one or two VLAN Tags are present in
         * the tunnel headers of tunneled packets. This selection
         * does not apply to non-tunneled packets.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_MASK \
                UINT32_C(0x18)
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_SFT \
                3
        /*
         * Select inner VLAN PRI when 1 or 2 VLAN Tags are
         * present in the tunnel packet headers
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_INNERMOST \
                (UINT32_C(0x0) << 3)
        /*
         * Select outer VLAN Tag PRI when 2 VLAN Tags are
         * present in the tunnel packet headers.
         * No VLAN PRI is selected for this configuration
         * if only one VLAN Tag is present in the tunnel
         * packet headers.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTER \
                (UINT32_C(0x1) << 3)
        /*
         * Select outermost VLAN PRI when 1 or 2 VLAN Tags
         * are present in the tunnel packet headers
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTERMOST \
                (UINT32_C(0x2) << 3)
        /* Unspecified */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED \
                (UINT32_C(0x3) << 3)
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_LAST \
                HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED
        /*
         * This field is used to provide default CoS value that
         * has been configured on this port.
         */
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_DEFAULT_COS_MASK \
                UINT32_C(0xe0)
        #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_DEFAULT_COS_SFT \
                5
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_port_mac_ptp_qcfg *
 **************************/


/* hwrm_port_mac_ptp_qcfg_input (size:192b/24B) */
struct hwrm_port_mac_ptp_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_mac_ptp_qcfg_output (size:640b/80B) */
struct hwrm_port_mac_ptp_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * In this field, a number of PTP related flags
         * are used to indicate configured PTP capabilities.
         */
        uint8_t flags;
        /*
         * When this bit is set to '1', the PTP related registers are
         * directly accessible by the host.
         */
        #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_DIRECT_ACCESS \
                UINT32_C(0x1)
        /*
         * When this bit is set to '1', the PTP information is accessible
         * via HWRM commands.
         */
        #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_HWRM_ACCESS \
                UINT32_C(0x2)
        uint8_t unused_0[3];
        /* Offset of the PTP register for the lower 32 bits of timestamp for RX. */
        uint32_t        rx_ts_reg_off_lower;
        /* Offset of the PTP register for the upper 32 bits of timestamp for RX. */
        uint32_t        rx_ts_reg_off_upper;
        /* Offset of the PTP register for the sequence ID for RX. */
        uint32_t        rx_ts_reg_off_seq_id;
        /* Offset of the first PTP source ID for RX. */
        uint32_t        rx_ts_reg_off_src_id_0;
        /* Offset of the second PTP source ID for RX. */
        uint32_t        rx_ts_reg_off_src_id_1;
        /* Offset of the third PTP source ID for RX. */
        uint32_t        rx_ts_reg_off_src_id_2;
        /* Offset of the domain ID for RX. */
        uint32_t        rx_ts_reg_off_domain_id;
        /* Offset of the PTP FIFO register for RX. */
        uint32_t        rx_ts_reg_off_fifo;
        /* Offset of the PTP advance FIFO register for RX. */
        uint32_t        rx_ts_reg_off_fifo_adv;
        /* PTP timestamp granularity for RX. */
        uint32_t        rx_ts_reg_off_granularity;
        /* Offset of the PTP register for the lower 32 bits of timestamp for TX. */
        uint32_t        tx_ts_reg_off_lower;
        /* Offset of the PTP register for the upper 32 bits of timestamp for TX. */
        uint32_t        tx_ts_reg_off_upper;
        /* Offset of the PTP register for the sequence ID for TX. */
        uint32_t        tx_ts_reg_off_seq_id;
        /* Offset of the PTP FIFO register for TX. */
        uint32_t        tx_ts_reg_off_fifo;
        /* PTP timestamp granularity for TX. */
        uint32_t        tx_ts_reg_off_granularity;
        uint8_t unused_1[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************
 * hwrm_port_qstats *
 ********************/


/* hwrm_port_qstats_input (size:320b/40B) */
struct hwrm_port_qstats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
        /*
         * This is the host address where
         * Tx port statistics will be stored
         */
        uint64_t        tx_stat_host_addr;
        /*
         * This is the host address where
         * Rx port statistics will be stored
         */
        uint64_t        rx_stat_host_addr;
} __attribute__((packed));

/* hwrm_port_qstats_output (size:128b/16B) */
struct hwrm_port_qstats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The size of TX port statistics block in bytes. */
        uint16_t        tx_stat_size;
        /* The size of RX port statistics block in bytes. */
        uint16_t        rx_stat_size;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/************************
 * hwrm_port_qstats_ext *
 ************************/


/* hwrm_port_qstats_ext_input (size:320b/40B) */
struct hwrm_port_qstats_ext_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is being queried. */
        uint16_t        port_id;
        /*
         * The size of TX port extended
         * statistics block in bytes.
         */
        uint16_t        tx_stat_size;
        /*
         * The size of RX port extended
         * statistics block in bytes
         */
        uint16_t        rx_stat_size;
        uint8_t unused_0[2];
        /*
         * This is the host address where
         * Tx port statistics will be stored
         */
        uint64_t        tx_stat_host_addr;
        /*
         * This is the host address where
         * Rx port statistics will be stored
         */
        uint64_t        rx_stat_host_addr;
} __attribute__((packed));

/* hwrm_port_qstats_ext_output (size:128b/16B) */
struct hwrm_port_qstats_ext_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The size of TX port statistics block in bytes. */
        uint16_t        tx_stat_size;
        /* The size of RX port statistics block in bytes. */
        uint16_t        rx_stat_size;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_port_lpbk_qstats *
 *************************/


/* hwrm_port_lpbk_qstats_input (size:128b/16B) */
struct hwrm_port_lpbk_qstats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_port_lpbk_qstats_output (size:768b/96B) */
struct hwrm_port_lpbk_qstats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Number of transmitted unicast frames */
        uint64_t        lpbk_ucast_frames;
        /* Number of transmitted multicast frames */
        uint64_t        lpbk_mcast_frames;
        /* Number of transmitted broadcast frames */
        uint64_t        lpbk_bcast_frames;
        /* Number of transmitted bytes for unicast traffic */
        uint64_t        lpbk_ucast_bytes;
        /* Number of transmitted bytes for multicast traffic */
        uint64_t        lpbk_mcast_bytes;
        /* Number of transmitted bytes for broadcast traffic */
        uint64_t        lpbk_bcast_bytes;
        /* Total Tx Drops for loopback traffic reported by STATS block */
        uint64_t        tx_stat_discard;
        /* Total Tx Error Drops for loopback traffic reported by STATS block */
        uint64_t        tx_stat_error;
        /* Total Rx Drops for loopback traffic reported by STATS block */
        uint64_t        rx_stat_discard;
        /* Total Rx Error Drops for loopback traffic reported by STATS block */
        uint64_t        rx_stat_error;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_port_clr_stats *
 ***********************/


/* hwrm_port_clr_stats_input (size:192b/24B) */
struct hwrm_port_clr_stats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_clr_stats_output (size:128b/16B) */
struct hwrm_port_clr_stats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/****************************
 * hwrm_port_lpbk_clr_stats *
 ****************************/


/* hwrm_port_lpbk_clr_stats_input (size:128b/16B) */
struct hwrm_port_lpbk_clr_stats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_port_lpbk_clr_stats_output (size:128b/16B) */
struct hwrm_port_lpbk_clr_stats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_port_ts_query *
 **********************/


/* hwrm_port_ts_query_input (size:192b/24B) */
struct hwrm_port_ts_query_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_TX    UINT32_C(0x0)
        /* rx path */
        #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_RX    UINT32_C(0x1)
        #define HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_LAST \
                HWRM_PORT_TS_QUERY_INPUT_FLAGS_PATH_RX
        /* Port ID of port that is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_port_ts_query_output (size:192b/24B) */
struct hwrm_port_ts_query_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Timestamp value of PTP message captured. */
        uint64_t        ptp_msg_ts;
        /* Sequence ID of the PTP message captured. */
        uint16_t        ptp_msg_seqid;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_port_phy_qcaps *
 ***********************/


/* hwrm_port_phy_qcaps_input (size:192b/24B) */
struct hwrm_port_phy_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port that is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_phy_qcaps_output (size:192b/24B) */
struct hwrm_port_phy_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* PHY capability flags */
        uint8_t flags;
        /*
         * If set to 1, then this field indicates that the
         * link is capable of supporting EEE.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_EEE_SUPPORTED \
                UINT32_C(0x1)
        /*
         * If set to 1, then this field indicates that the
         * PHY is capable of supporting external loopback.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_EXTERNAL_LPBK_SUPPORTED \
                UINT32_C(0x2)
        /*
         * Reserved field. The HWRM shall set this field to 0.
         * An HWRM client shall ignore this field.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_RSVD1_MASK \
                UINT32_C(0xfc)
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_RSVD1_SFT                   2
        /* Number of front panel ports for this device. */
        uint8_t port_cnt;
        /* Not supported or unknown */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_UNKNOWN UINT32_C(0x0)
        /* single port device */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_1       UINT32_C(0x1)
        /* 2-port device */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_2       UINT32_C(0x2)
        /* 3-port device */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_3       UINT32_C(0x3)
        /* 4-port device */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_4       UINT32_C(0x4)
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_LAST \
                HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_4
        /*
         * This is a bit mask to indicate what speeds are supported
         * as forced speeds on this link.
         * For each speed that can be forced on this link, the
         * corresponding mask bit shall be set to '1'.
         */
        uint16_t        supported_speeds_force_mode;
        /* 100Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100MBHD \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100MB \
                UINT32_C(0x2)
        /* 1Gb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_1GBHD \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_1GB \
                UINT32_C(0x8)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_2GB \
                UINT32_C(0x10)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_2_5GB \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10GB \
                UINT32_C(0x40)
        /* 20Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_20GB \
                UINT32_C(0x80)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_25GB \
                UINT32_C(0x100)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_40GB \
                UINT32_C(0x200)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_50GB \
                UINT32_C(0x400)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100GB \
                UINT32_C(0x800)
        /* 10Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10MBHD \
                UINT32_C(0x1000)
        /* 10Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10MB \
                UINT32_C(0x2000)
        /*
         * This is a bit mask to indicate what speeds are supported
         * for autonegotiation on this link.
         * For each speed that can be autonegotiated on this link, the
         * corresponding mask bit shall be set to '1'.
         */
        uint16_t        supported_speeds_auto_mode;
        /* 100Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100MBHD \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100MB \
                UINT32_C(0x2)
        /* 1Gb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_1GBHD \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_1GB \
                UINT32_C(0x8)
        /* 2Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_2GB \
                UINT32_C(0x10)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_2_5GB \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10GB \
                UINT32_C(0x40)
        /* 20Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_20GB \
                UINT32_C(0x80)
        /* 25Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_25GB \
                UINT32_C(0x100)
        /* 40Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_40GB \
                UINT32_C(0x200)
        /* 50Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_50GB \
                UINT32_C(0x400)
        /* 100Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100GB \
                UINT32_C(0x800)
        /* 10Mb link speed (Half-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10MBHD \
                UINT32_C(0x1000)
        /* 10Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10MB \
                UINT32_C(0x2000)
        /*
         * This is a bit mask to indicate what speeds are supported
         * for EEE on this link.
         * For each speed that can be autonegotiated when EEE is enabled
         * on this link, the corresponding mask bit shall be set to '1'.
         * This field is only valid when the eee_suppotred is set to '1'.
         */
        uint16_t        supported_speeds_eee_mode;
        /* Reserved */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD1 \
                UINT32_C(0x1)
        /* 100Mb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_100MB \
                UINT32_C(0x2)
        /* Reserved */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD2 \
                UINT32_C(0x4)
        /* 1Gb link speed (Full-duplex) */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_1GB \
                UINT32_C(0x8)
        /* Reserved */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD3 \
                UINT32_C(0x10)
        /* Reserved */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD4 \
                UINT32_C(0x20)
        /* 10Gb link speed */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_10GB \
                UINT32_C(0x40)
        uint32_t        tx_lpi_timer_low;
        /*
         * The lowest value of TX LPI timer that can be set on this link
         * when EEE is enabled. This value is in microseconds.
         * This field is valid only when_eee_supported is set to '1'.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_LOW_MASK \
                UINT32_C(0xffffff)
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_LOW_SFT 0
        /*
         * Reserved field. The HWRM shall set this field to 0.
         * An HWRM client shall ignore this field.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD2_MASK \
                UINT32_C(0xff000000)
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD2_SFT            24
        uint32_t        valid_tx_lpi_timer_high;
        /*
         * The highest value of TX LPI timer that can be set on this link
         * when EEE is enabled. This value is in microseconds.
         * This field is valid only when_eee_supported is set to '1'.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_HIGH_MASK \
                UINT32_C(0xffffff)
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_HIGH_SFT 0
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_VALID_MASK \
                UINT32_C(0xff000000)
        #define HWRM_PORT_PHY_QCAPS_OUTPUT_VALID_SFT             24
} __attribute__((packed));

/***************************
 * hwrm_port_phy_i2c_write *
 ***************************/


/* hwrm_port_phy_i2c_write_input (size:832b/104B) */
struct hwrm_port_phy_i2c_write_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        uint32_t        enables;
        /*
         * This bit must be '1' for the page_offset field to be
         * configured.
         */
        #define HWRM_PORT_PHY_I2C_WRITE_INPUT_ENABLES_PAGE_OFFSET \
                UINT32_C(0x1)
        /* Port ID of port. */
        uint16_t        port_id;
        /* 8-bit I2C slave address. */
        uint8_t i2c_slave_addr;
        uint8_t unused_0;
        /* The page number that is being accessed over I2C. */
        uint16_t        page_number;
        /* Offset within the page that is being accessed over I2C. */
        uint16_t        page_offset;
        /*
         * Length of data to write, in bytes starting at the offset
         * specified above. If the offset is not specified, then
         * the data shall be written from the beginning of the page.
         */
        uint8_t data_length;
        uint8_t unused_1[7];
        /* Up to 64B of data. */
        uint32_t        data[16];
} __attribute__((packed));

/* hwrm_port_phy_i2c_write_output (size:128b/16B) */
struct hwrm_port_phy_i2c_write_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_port_phy_i2c_read *
 **************************/


/* hwrm_port_phy_i2c_read_input (size:320b/40B) */
struct hwrm_port_phy_i2c_read_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        uint32_t        enables;
        /*
         * This bit must be '1' for the page_offset field to be
         * configured.
         */
        #define HWRM_PORT_PHY_I2C_READ_INPUT_ENABLES_PAGE_OFFSET \
                UINT32_C(0x1)
        /* Port ID of port. */
        uint16_t        port_id;
        /* 8-bit I2C slave address. */
        uint8_t i2c_slave_addr;
        uint8_t unused_0;
        /* The page number that is being accessed over I2C. */
        uint16_t        page_number;
        /* Offset within the page that is being accessed over I2C. */
        uint16_t        page_offset;
        /*
         * Length of data to read, in bytes starting at the offset
         * specified above. If the offset is not specified, then
         * the data shall be read from the beginning of the page.
         */
        uint8_t data_length;
        uint8_t unused_1[7];
} __attribute__((packed));

/* hwrm_port_phy_i2c_read_output (size:640b/80B) */
struct hwrm_port_phy_i2c_read_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Up to 64B of data. */
        uint32_t        data[16];
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_port_led_cfg *
 *********************/


/* hwrm_port_led_cfg_input (size:512b/64B) */
struct hwrm_port_led_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the led0_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the led0_state field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_STATE \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the led0_color field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_COLOR \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the led0_blink_on field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_ON \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the led0_blink_off field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_OFF \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the led0_group_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_GROUP_ID \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the led1_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_ID \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the led1_state field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_STATE \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the led1_color field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_COLOR \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the led1_blink_on field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_ON \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the led1_blink_off field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_OFF \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the led1_group_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_GROUP_ID \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the led2_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_ID \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the led2_state field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_STATE \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the led2_color field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_COLOR \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the led2_blink_on field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_ON \
                UINT32_C(0x8000)
        /*
         * This bit must be '1' for the led2_blink_off field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_OFF \
                UINT32_C(0x10000)
        /*
         * This bit must be '1' for the led2_group_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_GROUP_ID \
                UINT32_C(0x20000)
        /*
         * This bit must be '1' for the led3_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_ID \
                UINT32_C(0x40000)
        /*
         * This bit must be '1' for the led3_state field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_STATE \
                UINT32_C(0x80000)
        /*
         * This bit must be '1' for the led3_color field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_COLOR \
                UINT32_C(0x100000)
        /*
         * This bit must be '1' for the led3_blink_on field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_ON \
                UINT32_C(0x200000)
        /*
         * This bit must be '1' for the led3_blink_off field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_OFF \
                UINT32_C(0x400000)
        /*
         * This bit must be '1' for the led3_group_id field to be
         * configured.
         */
        #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_GROUP_ID \
                UINT32_C(0x800000)
        /* Port ID of port whose LEDs are configured. */
        uint16_t        port_id;
        /*
         * The number of LEDs that are being configured.
         * Up to 4 LEDs can be configured with this command.
         */
        uint8_t num_leds;
        /* Reserved field. */
        uint8_t rsvd;
        /* An identifier for the LED #0. */
        uint8_t led0_id;
        /* The requested state of the LED #0. */
        uint8_t led0_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT
        /* The requested color of LED #0. */
        uint8_t led0_color;
        /* Default */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER
        uint8_t unused_0;
        /*
         * If the LED #0 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led0_blink_on;
        /*
         * If the LED #0 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led0_blink_off;
        /*
         * An identifier for the group of LEDs that LED #0 belongs
         * to.
         * If set to 0, then the LED #0 shall not be grouped and
         * shall be treated as an individual resource.
         * For all other non-zero values of this field, LED #0 shall
         * be grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led0_group_id;
        /* Reserved field. */
        uint8_t rsvd0;
        /* An identifier for the LED #1. */
        uint8_t led1_id;
        /* The requested state of the LED #1. */
        uint8_t led1_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT
        /* The requested color of LED #1. */
        uint8_t led1_color;
        /* Default */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER
        uint8_t unused_1;
        /*
         * If the LED #1 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led1_blink_on;
        /*
         * If the LED #1 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led1_blink_off;
        /*
         * An identifier for the group of LEDs that LED #1 belongs
         * to.
         * If set to 0, then the LED #1 shall not be grouped and
         * shall be treated as an individual resource.
         * For all other non-zero values of this field, LED #1 shall
         * be grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led1_group_id;
        /* Reserved field. */
        uint8_t rsvd1;
        /* An identifier for the LED #2. */
        uint8_t led2_id;
        /* The requested state of the LED #2. */
        uint8_t led2_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT
        /* The requested color of LED #2. */
        uint8_t led2_color;
        /* Default */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER
        uint8_t unused_2;
        /*
         * If the LED #2 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led2_blink_on;
        /*
         * If the LED #2 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led2_blink_off;
        /*
         * An identifier for the group of LEDs that LED #2 belongs
         * to.
         * If set to 0, then the LED #2 shall not be grouped and
         * shall be treated as an individual resource.
         * For all other non-zero values of this field, LED #2 shall
         * be grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led2_group_id;
        /* Reserved field. */
        uint8_t rsvd2;
        /* An identifier for the LED #3. */
        uint8_t led3_id;
        /* The requested state of the LED #3. */
        uint8_t led3_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT
        /* The requested color of LED #3. */
        uint8_t led3_color;
        /* Default */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_LAST \
                HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER
        uint8_t unused_3;
        /*
         * If the LED #3 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led3_blink_on;
        /*
         * If the LED #3 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led3_blink_off;
        /*
         * An identifier for the group of LEDs that LED #3 belongs
         * to.
         * If set to 0, then the LED #3 shall not be grouped and
         * shall be treated as an individual resource.
         * For all other non-zero values of this field, LED #3 shall
         * be grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led3_group_id;
        /* Reserved field. */
        uint8_t rsvd3;
} __attribute__((packed));

/* hwrm_port_led_cfg_output (size:128b/16B) */
struct hwrm_port_led_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_port_led_qcfg *
 **********************/


/* hwrm_port_led_qcfg_input (size:192b/24B) */
struct hwrm_port_led_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port whose LED configuration is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_led_qcfg_output (size:448b/56B) */
struct hwrm_port_led_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * The number of LEDs that are configured on this port.
         * Up to 4 LEDs can be returned in the response.
         */
        uint8_t num_leds;
        /* An identifier for the LED #0. */
        uint8_t led0_id;
        /* The type of LED #0. */
        uint8_t led0_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID
        /* The current state of the LED #0. */
        uint8_t led0_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT
        /* The color of LED #0. */
        uint8_t led0_color;
        /* Default */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER
        uint8_t unused_0;
        /*
         * If the LED #0 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led0_blink_on;
        /*
         * If the LED #0 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led0_blink_off;
        /*
         * An identifier for the group of LEDs that LED #0 belongs
         * to.
         * If set to 0, then the LED #0 is not grouped.
         * For all other non-zero values of this field, LED #0 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led0_group_id;
        /* An identifier for the LED #1. */
        uint8_t led1_id;
        /* The type of LED #1. */
        uint8_t led1_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID
        /* The current state of the LED #1. */
        uint8_t led1_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT
        /* The color of LED #1. */
        uint8_t led1_color;
        /* Default */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER
        uint8_t unused_1;
        /*
         * If the LED #1 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led1_blink_on;
        /*
         * If the LED #1 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led1_blink_off;
        /*
         * An identifier for the group of LEDs that LED #1 belongs
         * to.
         * If set to 0, then the LED #1 is not grouped.
         * For all other non-zero values of this field, LED #1 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led1_group_id;
        /* An identifier for the LED #2. */
        uint8_t led2_id;
        /* The type of LED #2. */
        uint8_t led2_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID
        /* The current state of the LED #2. */
        uint8_t led2_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT
        /* The color of LED #2. */
        uint8_t led2_color;
        /* Default */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER
        uint8_t unused_2;
        /*
         * If the LED #2 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led2_blink_on;
        /*
         * If the LED #2 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led2_blink_off;
        /*
         * An identifier for the group of LEDs that LED #2 belongs
         * to.
         * If set to 0, then the LED #2 is not grouped.
         * For all other non-zero values of this field, LED #2 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led2_group_id;
        /* An identifier for the LED #3. */
        uint8_t led3_id;
        /* The type of LED #3. */
        uint8_t led3_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID
        /* The current state of the LED #3. */
        uint8_t led3_state;
        /* Default state of the LED */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_DEFAULT  UINT32_C(0x0)
        /* Off */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_OFF      UINT32_C(0x1)
        /* On */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_ON       UINT32_C(0x2)
        /* Blink */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINK    UINT32_C(0x3)
        /* Blink Alternately */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT
        /* The color of LED #3. */
        uint8_t led3_color;
        /* Default */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_DEFAULT    UINT32_C(0x0)
        /* Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_AMBER      UINT32_C(0x1)
        /* Green */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREEN      UINT32_C(0x2)
        /* Green or Amber */
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
        #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_LAST \
                HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER
        uint8_t unused_3;
        /*
         * If the LED #3 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED on between cycles.
         */
        uint16_t        led3_blink_on;
        /*
         * If the LED #3 state is "blink" or "blinkalt", then
         * this field represents the requested time in milliseconds
         * to keep LED off between cycles.
         */
        uint16_t        led3_blink_off;
        /*
         * An identifier for the group of LEDs that LED #3 belongs
         * to.
         * If set to 0, then the LED #3 is not grouped.
         * For all other non-zero values of this field, LED #3 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led3_group_id;
        uint8_t unused_4[6];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_port_led_qcaps *
 ***********************/


/* hwrm_port_led_qcaps_input (size:192b/24B) */
struct hwrm_port_led_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Port ID of port whose LED configuration is being queried. */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_port_led_qcaps_output (size:384b/48B) */
struct hwrm_port_led_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * The number of LEDs that are configured on this port.
         * Up to 4 LEDs can be returned in the response.
         */
        uint8_t num_leds;
        /* Reserved for future use. */
        uint8_t unused[3];
        /* An identifier for the LED #0. */
        uint8_t led0_id;
        /* The type of LED #0. */
        uint8_t led0_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_LAST \
                HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID
        /*
         * An identifier for the group of LEDs that LED #0 belongs
         * to.
         * If set to 0, then the LED #0 cannot be grouped.
         * For all other non-zero values of this field, LED #0 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led0_group_id;
        uint8_t unused_0;
        /* The states supported by LED #0. */
        uint16_t        led0_state_caps;
        /*
         * If set to 1, this LED is enabled.
         * If set to 0, this LED is disabled.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ENABLED \
                UINT32_C(0x1)
        /*
         * If set to 1, off state is supported on this LED.
         * If set to 0, off state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_OFF_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, on state is supported on this LED.
         * If set to 0, on state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ON_SUPPORTED \
                UINT32_C(0x4)
        /*
         * If set to 1, blink state is supported on this LED.
         * If set to 0, blink state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_SUPPORTED \
                UINT32_C(0x8)
        /*
         * If set to 1, blink_alt state is supported on this LED.
         * If set to 0, blink_alt state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_ALT_SUPPORTED \
                UINT32_C(0x10)
        /* The colors supported by LED #0. */
        uint16_t        led0_color_caps;
        /* reserved. */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_RSVD \
                UINT32_C(0x1)
        /*
         * If set to 1, Amber color is supported on this LED.
         * If set to 0, Amber color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_AMBER_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, Green color is supported on this LED.
         * If set to 0, Green color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_GREEN_SUPPORTED \
                UINT32_C(0x4)
        /* An identifier for the LED #1. */
        uint8_t led1_id;
        /* The type of LED #1. */
        uint8_t led1_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_LAST \
                HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_INVALID
        /*
         * An identifier for the group of LEDs that LED #1 belongs
         * to.
         * If set to 0, then the LED #0 cannot be grouped.
         * For all other non-zero values of this field, LED #0 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led1_group_id;
        uint8_t unused_1;
        /* The states supported by LED #1. */
        uint16_t        led1_state_caps;
        /*
         * If set to 1, this LED is enabled.
         * If set to 0, this LED is disabled.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ENABLED \
                UINT32_C(0x1)
        /*
         * If set to 1, off state is supported on this LED.
         * If set to 0, off state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_OFF_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, on state is supported on this LED.
         * If set to 0, on state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ON_SUPPORTED \
                UINT32_C(0x4)
        /*
         * If set to 1, blink state is supported on this LED.
         * If set to 0, blink state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_SUPPORTED \
                UINT32_C(0x8)
        /*
         * If set to 1, blink_alt state is supported on this LED.
         * If set to 0, blink_alt state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_ALT_SUPPORTED \
                UINT32_C(0x10)
        /* The colors supported by LED #1. */
        uint16_t        led1_color_caps;
        /* reserved. */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_RSVD \
                UINT32_C(0x1)
        /*
         * If set to 1, Amber color is supported on this LED.
         * If set to 0, Amber color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_AMBER_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, Green color is supported on this LED.
         * If set to 0, Green color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_GREEN_SUPPORTED \
                UINT32_C(0x4)
        /* An identifier for the LED #2. */
        uint8_t led2_id;
        /* The type of LED #2. */
        uint8_t led2_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_LAST \
                HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_INVALID
        /*
         * An identifier for the group of LEDs that LED #0 belongs
         * to.
         * If set to 0, then the LED #0 cannot be grouped.
         * For all other non-zero values of this field, LED #0 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led2_group_id;
        uint8_t unused_2;
        /* The states supported by LED #2. */
        uint16_t        led2_state_caps;
        /*
         * If set to 1, this LED is enabled.
         * If set to 0, this LED is disabled.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ENABLED \
                UINT32_C(0x1)
        /*
         * If set to 1, off state is supported on this LED.
         * If set to 0, off state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_OFF_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, on state is supported on this LED.
         * If set to 0, on state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ON_SUPPORTED \
                UINT32_C(0x4)
        /*
         * If set to 1, blink state is supported on this LED.
         * If set to 0, blink state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_SUPPORTED \
                UINT32_C(0x8)
        /*
         * If set to 1, blink_alt state is supported on this LED.
         * If set to 0, blink_alt state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_ALT_SUPPORTED \
                UINT32_C(0x10)
        /* The colors supported by LED #2. */
        uint16_t        led2_color_caps;
        /* reserved. */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_RSVD \
                UINT32_C(0x1)
        /*
         * If set to 1, Amber color is supported on this LED.
         * If set to 0, Amber color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_AMBER_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, Green color is supported on this LED.
         * If set to 0, Green color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_GREEN_SUPPORTED \
                UINT32_C(0x4)
        /* An identifier for the LED #3. */
        uint8_t led3_id;
        /* The type of LED #3. */
        uint8_t led3_type;
        /* Speed LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_SPEED    UINT32_C(0x0)
        /* Activity LED */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
        /* Invalid */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_INVALID  UINT32_C(0xff)
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_LAST \
                HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_INVALID
        /*
         * An identifier for the group of LEDs that LED #3 belongs
         * to.
         * If set to 0, then the LED #0 cannot be grouped.
         * For all other non-zero values of this field, LED #0 is
         * grouped together with the LEDs with the same group ID
         * value.
         */
        uint8_t led3_group_id;
        uint8_t unused_3;
        /* The states supported by LED #3. */
        uint16_t        led3_state_caps;
        /*
         * If set to 1, this LED is enabled.
         * If set to 0, this LED is disabled.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ENABLED \
                UINT32_C(0x1)
        /*
         * If set to 1, off state is supported on this LED.
         * If set to 0, off state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_OFF_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, on state is supported on this LED.
         * If set to 0, on state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ON_SUPPORTED \
                UINT32_C(0x4)
        /*
         * If set to 1, blink state is supported on this LED.
         * If set to 0, blink state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_SUPPORTED \
                UINT32_C(0x8)
        /*
         * If set to 1, blink_alt state is supported on this LED.
         * If set to 0, blink_alt state is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_ALT_SUPPORTED \
                UINT32_C(0x10)
        /* The colors supported by LED #3. */
        uint16_t        led3_color_caps;
        /* reserved. */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_RSVD \
                UINT32_C(0x1)
        /*
         * If set to 1, Amber color is supported on this LED.
         * If set to 0, Amber color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_AMBER_SUPPORTED \
                UINT32_C(0x2)
        /*
         * If set to 1, Green color is supported on this LED.
         * If set to 0, Green color is not supported on this LED.
         */
        #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_GREEN_SUPPORTED \
                UINT32_C(0x4)
        uint8_t unused_4[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_queue_qportcfg *
 ***********************/


/* hwrm_queue_qportcfg_input (size:192b/24B) */
struct hwrm_queue_qportcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX    UINT32_C(0x0)
        /* rx path */
        #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX    UINT32_C(0x1)
        #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \
                HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX
        /*
         * Port ID of port for which the queue configuration is being
         * queried.  This field is only required when sent by IPC.
         */
        uint16_t        port_id;
        /*
         * Drivers will set this capability when it can use
         * queue_idx_service_profile to map the queues to application.
         */
        uint8_t drv_qmap_cap;
        /* disabled */
        #define HWRM_QUEUE_QPORTCFG_INPUT_DRV_QMAP_CAP_DISABLED UINT32_C(0x0)
        /* enabled */
        #define HWRM_QUEUE_QPORTCFG_INPUT_DRV_QMAP_CAP_ENABLED  UINT32_C(0x1)
        #define HWRM_QUEUE_QPORTCFG_INPUT_DRV_QMAP_CAP_LAST \
                HWRM_QUEUE_QPORTCFG_INPUT_DRV_QMAP_CAP_ENABLED
        uint8_t unused_0;
} __attribute__((packed));

/* hwrm_queue_qportcfg_output (size:256b/32B) */
struct hwrm_queue_qportcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * The maximum number of queues that can be configured on this
         * port.
         * Valid values range from 1 through 8.
         */
        uint8_t max_configurable_queues;
        /*
         * The maximum number of lossless queues that can be configured
         * on this port.
         * Valid values range from 0 through 8.
         */
        uint8_t max_configurable_lossless_queues;
        /*
         * Bitmask indicating which queues can be configured by the
         * hwrm_queue_cfg command.
         *
         * Each bit represents a specific queue where bit 0 represents
         * queue 0 and bit 7 represents queue 7.
         * # A value of 0 indicates that the queue is not configurable
         * by the hwrm_queue_cfg command.
         * # A value of 1 indicates that the queue is configurable.
         * # A hwrm_queue_cfg command shall return error when trying to
         * configure a queue not configurable.
         */
        uint8_t queue_cfg_allowed;
        /* Information about queue configuration. */
        uint8_t queue_cfg_info;
        /*
         * If this flag is set to '1', then the queues are
         * configured asymmetrically on TX and RX sides.
         * If this flag is set to '0', then the queues are
         * configured symmetrically on TX and RX sides. For
         * symmetric configuration, the queue configuration
         * including queue ids and service profiles on the
         * TX side is the same as the corresponding queue
         * configuration on the RX side.
         */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG \
                UINT32_C(0x1)
        /*
         * Bitmask indicating which queues can be configured by the
         * hwrm_queue_pfcenable_cfg command.
         *
         * Each bit represents a specific priority where bit 0 represents
         * priority 0 and bit 7 represents priority 7.
         * # A value of 0 indicates that the priority is not configurable by
         * the hwrm_queue_pfcenable_cfg command.
         * # A value of 1 indicates that the priority is configurable.
         * # A hwrm_queue_pfcenable_cfg command shall return error when
         * trying to configure a priority that is not configurable.
         */
        uint8_t queue_pfcenable_cfg_allowed;
        /*
         * Bitmask indicating which queues can be configured by the
         * hwrm_queue_pri2cos_cfg command.
         *
         * Each bit represents a specific queue where bit 0 represents
         * queue 0 and bit 7 represents queue 7.
         * # A value of 0 indicates that the queue is not configurable
         * by the hwrm_queue_pri2cos_cfg command.
         * # A value of 1 indicates that the queue is configurable.
         * # A hwrm_queue_pri2cos_cfg command shall return error when
         * trying to configure a queue that is not configurable.
         */
        uint8_t queue_pri2cos_cfg_allowed;
        /*
         * Bitmask indicating which queues can be configured by the
         * hwrm_queue_pri2cos_cfg command.
         *
         * Each bit represents a specific queue where bit 0 represents
         * queue 0 and bit 7 represents queue 7.
         * # A value of 0 indicates that the queue is not configurable
         * by the hwrm_queue_pri2cos_cfg command.
         * # A value of 1 indicates that the queue is configurable.
         * # A hwrm_queue_pri2cos_cfg command shall return error when
         * trying to configure a queue not configurable.
         */
        uint8_t queue_cos2bw_cfg_allowed;
        /*
         * ID of CoS Queue 0.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id0;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id0_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 1.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id1;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id1_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 2.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id2;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id2_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 3.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id3;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id3_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 4.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id4;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id4_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 5.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id5;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id5_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 6.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id6;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id6_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN
        /*
         * ID of CoS Queue 7.
         * FF - Invalid id
         *
         * # This ID can be used on any subsequent call to an hwrm command
         * that takes a queue id.
         * # IDs must always be queried by this command before any use
         * by the driver or software.
         * # Any driver or software should not make any assumptions about
         * queue IDs.
         * # A value of 0xff indicates that the queue is not available.
         * # Available queues may not be in sequential order.
         */
        uint8_t queue_id7;
        /* This value is applicable to CoS queues only. */
        uint8_t queue_id7_service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \
                UINT32_C(0x0)
        /* Lossless (legacy) */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
                UINT32_C(0x1)
        /* Lossless RoCE */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS_ROCE \
                UINT32_C(0x1)
        /* Lossy RoCE CNP */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY_ROCE_CNP \
                UINT32_C(0x2)
        /* Lossless NIC */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS_NIC \
                UINT32_C(0x3)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
                UINT32_C(0xff)
        #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************
 * hwrm_queue_qcfg *
 *******************/


/* hwrm_queue_qcfg_input (size:192b/24B) */
struct hwrm_queue_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_TX    UINT32_C(0x0)
        /* rx path */
        #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_RX    UINT32_C(0x1)
        #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_LAST \
                HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_RX
        /* Queue ID of the queue. */
        uint32_t        queue_id;
} __attribute__((packed));

/* hwrm_queue_qcfg_output (size:128b/16B) */
struct hwrm_queue_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This value is a the estimate packet length used in the
         * TX arbiter.
         */
        uint32_t        queue_len;
        /* This value is applicable to CoS queues only. */
        uint8_t service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LOSSY    UINT32_C(0x0)
        /* Lossless */
        #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LOSSLESS UINT32_C(0x1)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_UNKNOWN  UINT32_C(0xff)
        #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_UNKNOWN
        /* Information about queue configuration. */
        uint8_t queue_cfg_info;
        /*
         * If this flag is set to '1', then the queue is
         * configured asymmetrically on TX and RX sides.
         * If this flag is set to '0', then this queue is
         * configured symmetrically on TX and RX sides.
         */
        #define HWRM_QUEUE_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG \
                UINT32_C(0x1)
        uint8_t unused_0;
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************
 * hwrm_queue_cfg *
 ******************/


/* hwrm_queue_cfg_input (size:320b/40B) */
struct hwrm_queue_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX, or both directions applicable to the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_MASK UINT32_C(0x3)
        #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_SFT  0
        /* tx path */
        #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_TX     UINT32_C(0x0)
        /* rx path */
        #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_RX     UINT32_C(0x1)
        /* Bi-directional (Symmetrically applicable to TX and RX paths) */
        #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_BIDIR  UINT32_C(0x2)
        #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_LAST \
                HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_BIDIR
        uint32_t        enables;
        /*
         * This bit must be '1' for the dflt_len field to be
         * configured.
         */
        #define HWRM_QUEUE_CFG_INPUT_ENABLES_DFLT_LEN            UINT32_C(0x1)
        /*
         * This bit must be '1' for the service_profile field to be
         * configured.
         */
        #define HWRM_QUEUE_CFG_INPUT_ENABLES_SERVICE_PROFILE     UINT32_C(0x2)
        /* Queue ID of queue that is to be configured by this function. */
        uint32_t        queue_id;
        /*
         * This value is a the estimate packet length used in the
         * TX arbiter.
         * Set to 0xFF... (All Fs) to not adjust this value.
         */
        uint32_t        dflt_len;
        /* This value is applicable to CoS queues only. */
        uint8_t service_profile;
        /* Lossy (best-effort) */
        #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LOSSY    UINT32_C(0x0)
        /* Lossless */
        #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LOSSLESS UINT32_C(0x1)
        /* Set to 0xFF... (All Fs) if there is no service profile specified */
        #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_UNKNOWN  UINT32_C(0xff)
        #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LAST \
                HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_UNKNOWN
        uint8_t unused_0[7];
} __attribute__((packed));

/* hwrm_queue_cfg_output (size:128b/16B) */
struct hwrm_queue_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************************
 * hwrm_queue_pfcenable_qcfg *
 *****************************/


/* hwrm_queue_pfcenable_qcfg_input (size:192b/24B) */
struct hwrm_queue_pfcenable_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_queue_pfcenable_qcfg_output (size:128b/16B) */
struct hwrm_queue_pfcenable_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint32_t        flags;
        /* If set to 1, then PFC is enabled on PRI 0. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI0_PFC_ENABLED \
                UINT32_C(0x1)
        /* If set to 1, then PFC is enabled on PRI 1. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI1_PFC_ENABLED \
                UINT32_C(0x2)
        /* If set to 1, then PFC is enabled on PRI 2. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI2_PFC_ENABLED \
                UINT32_C(0x4)
        /* If set to 1, then PFC is enabled on PRI 3. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI3_PFC_ENABLED \
                UINT32_C(0x8)
        /* If set to 1, then PFC is enabled on PRI 4. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI4_PFC_ENABLED \
                UINT32_C(0x10)
        /* If set to 1, then PFC is enabled on PRI 5. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI5_PFC_ENABLED \
                UINT32_C(0x20)
        /* If set to 1, then PFC is enabled on PRI 6. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI6_PFC_ENABLED \
                UINT32_C(0x40)
        /* If set to 1, then PFC is enabled on PRI 7. */
        #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI7_PFC_ENABLED \
                UINT32_C(0x80)
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/****************************
 * hwrm_queue_pfcenable_cfg *
 ****************************/


/* hwrm_queue_pfcenable_cfg_input (size:192b/24B) */
struct hwrm_queue_pfcenable_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* If set to 1, then PFC is requested to be enabled on PRI 0. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI0_PFC_ENABLED \
                UINT32_C(0x1)
        /* If set to 1, then PFC is requested to be enabled on PRI 1. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI1_PFC_ENABLED \
                UINT32_C(0x2)
        /* If set to 1, then PFC is requested to  be enabled on PRI 2. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI2_PFC_ENABLED \
                UINT32_C(0x4)
        /* If set to 1, then PFC is requested to  be enabled on PRI 3. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI3_PFC_ENABLED \
                UINT32_C(0x8)
        /* If set to 1, then PFC is requested to  be enabled on PRI 4. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI4_PFC_ENABLED \
                UINT32_C(0x10)
        /* If set to 1, then PFC is requested to  be enabled on PRI 5. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI5_PFC_ENABLED \
                UINT32_C(0x20)
        /* If set to 1, then PFC is requested to  be enabled on PRI 6. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI6_PFC_ENABLED \
                UINT32_C(0x40)
        /* If set to 1, then PFC is requested to  be enabled on PRI 7. */
        #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI7_PFC_ENABLED \
                UINT32_C(0x80)
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint16_t        port_id;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_queue_pfcenable_cfg_output (size:128b/16B) */
struct hwrm_queue_pfcenable_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_queue_pri2cos_qcfg *
 ***************************/


/* hwrm_queue_pri2cos_qcfg_input (size:192b/24B) */
struct hwrm_queue_pri2cos_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH      UINT32_C(0x1)
        /* tx path */
        #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_TX     UINT32_C(0x0)
        /* rx path */
        #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX     UINT32_C(0x1)
        #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_LAST \
                HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX
        /*
         * When this bit is set to '0', the query is
         * for VLAN PRI field in tunnel headers.
         * When this bit is set to '1', the query is
         * for VLAN PRI field in inner packet headers.
         */
        #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_IVLAN     UINT32_C(0x2)
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint8_t port_id;
        uint8_t unused_0[3];
} __attribute__((packed));

/* hwrm_queue_pri2cos_qcfg_output (size:192b/24B) */
struct hwrm_queue_pri2cos_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * CoS Queue assigned to priority 0.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri0_cos_queue_id;
        /*
         * CoS Queue assigned to priority 1.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri1_cos_queue_id;
        /*
         * CoS Queue assigned to priority 2  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri2_cos_queue_id;
        /*
         * CoS Queue assigned to priority 3.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri3_cos_queue_id;
        /*
         * CoS Queue assigned to priority 4.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri4_cos_queue_id;
        /*
         * CoS Queue assigned to priority 5.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri5_cos_queue_id;
        /*
         * CoS Queue assigned to priority 6.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri6_cos_queue_id;
        /*
         * CoS Queue assigned to priority 7.  This value can only
         * be changed before traffic has started.
         * A value of 0xff indicates that no CoS queue is assigned to the
         * specified priority.
         */
        uint8_t pri7_cos_queue_id;
        /* Information about queue configuration. */
        uint8_t queue_cfg_info;
        /*
         * If this flag is set to '1', then the PRI to CoS
         * configuration is asymmetric on TX and RX sides.
         * If this flag is set to '0', then PRI to CoS configuration
         * is symmetric on TX and RX sides.
         */
        #define HWRM_QUEUE_PRI2COS_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG \
                UINT32_C(0x1)
        uint8_t unused_0[6];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_queue_pri2cos_cfg *
 **************************/


/* hwrm_queue_pri2cos_cfg_input (size:320b/40B) */
struct hwrm_queue_pri2cos_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX, or both directions applicable to the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_MASK UINT32_C(0x3)
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_SFT  0
        /* tx path */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_TX     UINT32_C(0x0)
        /* rx path */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_RX     UINT32_C(0x1)
        /* Bi-directional (Symmetrically applicable to TX and RX paths) */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR  UINT32_C(0x2)
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_LAST \
                HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR
        /*
         * When this bit is set to '0', the mapping is requested
         * for VLAN PRI field in tunnel headers.
         * When this bit is set to '1', the mapping is requested
         * for VLAN PRI field in inner packet headers.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_IVLAN     UINT32_C(0x4)
        uint32_t        enables;
        /*
         * This bit must be '1' for the pri0_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI0_COS_QUEUE_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the pri1_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI1_COS_QUEUE_ID \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the pri2_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI2_COS_QUEUE_ID \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the pri3_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI3_COS_QUEUE_ID \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the pri4_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI4_COS_QUEUE_ID \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the pri5_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI5_COS_QUEUE_ID \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the pri6_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI6_COS_QUEUE_ID \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the pri7_cos_queue_id field to be
         * configured.
         */
        #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI7_COS_QUEUE_ID \
                UINT32_C(0x80)
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint8_t port_id;
        /*
         * CoS Queue assigned to priority 0.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri0_cos_queue_id;
        /*
         * CoS Queue assigned to priority 1.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri1_cos_queue_id;
        /*
         * CoS Queue assigned to priority 2  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri2_cos_queue_id;
        /*
         * CoS Queue assigned to priority 3.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri3_cos_queue_id;
        /*
         * CoS Queue assigned to priority 4.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri4_cos_queue_id;
        /*
         * CoS Queue assigned to priority 5.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri5_cos_queue_id;
        /*
         * CoS Queue assigned to priority 6.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri6_cos_queue_id;
        /*
         * CoS Queue assigned to priority 7.  This value can only
         * be changed before traffic has started.
         */
        uint8_t pri7_cos_queue_id;
        uint8_t unused_0[7];
} __attribute__((packed));

/* hwrm_queue_pri2cos_cfg_output (size:128b/16B) */
struct hwrm_queue_pri2cos_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_queue_cos2bw_qcfg *
 **************************/


/* hwrm_queue_cos2bw_qcfg_input (size:192b/24B) */
struct hwrm_queue_cos2bw_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure TC BW assignment on this port.
         */
        uint16_t        port_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_queue_cos2bw_qcfg_output (size:896b/112B) */
struct hwrm_queue_cos2bw_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* ID of CoS Queue 0. */
        uint8_t queue_id0;
        uint8_t unused_0;
        uint16_t        unused_1;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id0_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id0_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id0_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id0_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id0_bw_weight;
        /* ID of CoS Queue 1. */
        uint8_t queue_id1;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id1_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id1_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id1_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id1_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id1_bw_weight;
        /* ID of CoS Queue 2. */
        uint8_t queue_id2;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id2_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id2_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id2_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id2_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id2_bw_weight;
        /* ID of CoS Queue 3. */
        uint8_t queue_id3;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id3_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id3_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id3_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id3_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id3_bw_weight;
        /* ID of CoS Queue 4. */
        uint8_t queue_id4;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id4_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id4_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id4_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id4_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id4_bw_weight;
        /* ID of CoS Queue 5. */
        uint8_t queue_id5;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id5_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id5_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id5_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id5_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id5_bw_weight;
        /* ID of CoS Queue 6. */
        uint8_t queue_id6;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id6_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id6_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id6_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id6_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id6_bw_weight;
        /* ID of CoS Queue 7. */
        uint8_t queue_id7;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id7_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id7_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id7_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id7_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id7_bw_weight;
        uint8_t unused_2[4];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_queue_cos2bw_cfg *
 *************************/


/* hwrm_queue_cos2bw_cfg_input (size:1024b/128B) */
struct hwrm_queue_cos2bw_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        uint32_t        enables;
        /*
         * If this bit is set to 1, then all queue_id0 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID0_VALID \
                UINT32_C(0x1)
        /*
         * If this bit is set to 1, then all queue_id1 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID1_VALID \
                UINT32_C(0x2)
        /*
         * If this bit is set to 1, then all queue_id2 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID2_VALID \
                UINT32_C(0x4)
        /*
         * If this bit is set to 1, then all queue_id3 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID3_VALID \
                UINT32_C(0x8)
        /*
         * If this bit is set to 1, then all queue_id4 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID4_VALID \
                UINT32_C(0x10)
        /*
         * If this bit is set to 1, then all queue_id5 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID5_VALID \
                UINT32_C(0x20)
        /*
         * If this bit is set to 1, then all queue_id6 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID6_VALID \
                UINT32_C(0x40)
        /*
         * If this bit is set to 1, then all queue_id7 related
         * parameters in this command are valid.
         */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID7_VALID \
                UINT32_C(0x80)
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure TC BW assignment on this port.
         */
        uint16_t        port_id;
        /* ID of CoS Queue 0. */
        uint8_t queue_id0;
        uint8_t unused_0;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id0_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id0_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id0_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id0_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id0_bw_weight;
        /* ID of CoS Queue 1. */
        uint8_t queue_id1;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id1_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id1_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id1_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id1_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id1_bw_weight;
        /* ID of CoS Queue 2. */
        uint8_t queue_id2;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id2_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id2_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id2_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id2_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id2_bw_weight;
        /* ID of CoS Queue 3. */
        uint8_t queue_id3;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id3_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id3_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id3_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id3_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id3_bw_weight;
        /* ID of CoS Queue 4. */
        uint8_t queue_id4;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id4_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id4_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id4_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id4_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id4_bw_weight;
        /* ID of CoS Queue 5. */
        uint8_t queue_id5;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id5_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id5_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id5_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id5_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id5_bw_weight;
        /* ID of CoS Queue 6. */
        uint8_t queue_id6;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id6_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id6_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id6_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id6_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id6_bw_weight;
        /* ID of CoS Queue 7. */
        uint8_t queue_id7;
        /*
         * Minimum BW allocated to CoS Queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id7_min_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
        /*
         * Maximum BW allocated to CoS queue.
         * The HWRM will translate this value into byte counter and
         * time interval used for this COS inside the device.
         */
        uint32_t        queue_id7_max_bw;
        /* The bandwidth value. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
        /* Transmission Selection Algorithm (TSA) for CoS Queue. */
        uint8_t queue_id7_tsa_assign;
        /* Strict Priority */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_SP \
                UINT32_C(0x0)
        /* Enhanced Transmission Selection */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_ETS \
                UINT32_C(0x1)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
                UINT32_C(0x2)
        /* reserved. */
        #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
                UINT32_C(0xff)
        /*
         * Priority level for strict priority. Valid only when the
         * tsa_assign is 0 - Strict Priority (SP)
         * 0..7 - Valid values.
         * 8..255 - Reserved.
         */
        uint8_t queue_id7_pri_lvl;
        /*
         * Weight used to allocate remaining BW for this COS after
         * servicing guaranteed bandwidths for all COS.
         */
        uint8_t queue_id7_bw_weight;
        uint8_t unused_1[5];
} __attribute__((packed));

/* hwrm_queue_cos2bw_cfg_output (size:128b/16B) */
struct hwrm_queue_cos2bw_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_queue_dscp_qcaps *
 *************************/


/* hwrm_queue_dscp_qcaps_input (size:192b/24B) */
struct hwrm_queue_dscp_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint8_t port_id;
        uint8_t unused_0[7];
} __attribute__((packed));

/* hwrm_queue_dscp_qcaps_output (size:128b/16B) */
struct hwrm_queue_dscp_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The number of bits provided by the hardware for the DSCP value. */
        uint8_t num_dscp_bits;
        uint8_t unused_0;
        /* Max number of DSCP-MASK-PRI entries supported. */
        uint16_t        max_entries;
        uint8_t unused_1[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/****************************
 * hwrm_queue_dscp2pri_qcfg *
 ****************************/


/* hwrm_queue_dscp2pri_qcfg_input (size:256b/32B) */
struct hwrm_queue_dscp2pri_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is the host address where the 24-bits DSCP-MASK-PRI
         * tuple(s) will be copied to.
         */
        uint64_t        dest_data_addr;
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint8_t port_id;
        uint8_t unused_0;
        /* Size of the buffer pointed to by dest_data_addr. */
        uint16_t        dest_data_buffer_size;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_queue_dscp2pri_qcfg_output (size:128b/16B) */
struct hwrm_queue_dscp2pri_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * A count of the number of DSCP-MASK-PRI tuple(s) pointed to
         * by the dest_data_addr.
         */
        uint16_t        entry_cnt;
        /*
         * This is the default PRI which un-initialized DSCP values are
         * mapped to.
         */
        uint8_t default_pri;
        uint8_t unused_0[4];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_queue_dscp2pri_cfg *
 ***************************/


/* hwrm_queue_dscp2pri_cfg_input (size:320b/40B) */
struct hwrm_queue_dscp2pri_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is the host address where the 24-bits DSCP-MASK-PRI tuple
         * will be copied from.
         */
        uint64_t        src_data_addr;
        uint32_t        flags;
        /* use_hw_default_pri is 1 b */
        #define HWRM_QUEUE_DSCP2PRI_CFG_INPUT_FLAGS_USE_HW_DEFAULT_PRI \
                UINT32_C(0x1)
        uint32_t        enables;
        /*
         * This bit must be '1' for the default_pri field to be
         * configured.
         */
        #define HWRM_QUEUE_DSCP2PRI_CFG_INPUT_ENABLES_DEFAULT_PRI \
                UINT32_C(0x1)
        /*
         * Port ID of port for which the table is being configured.
         * The HWRM needs to check whether this function is allowed
         * to configure pri2cos mapping on this port.
         */
        uint8_t port_id;
        /*
         * This is the default PRI which un-initialized DSCP values will be
         * mapped to.
         */
        uint8_t default_pri;
        /*
         * A count of the number of DSCP-MASK-PRI tuple(s) in the data pointed
         * to by src_data_addr.
         */
        uint16_t        entry_cnt;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_queue_dscp2pri_cfg_output (size:128b/16B) */
struct hwrm_queue_dscp2pri_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************
 * hwrm_vnic_alloc *
 *******************/


/* hwrm_vnic_alloc_input (size:192b/24B) */
struct hwrm_vnic_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is '1', this VNIC is requested to
         * be the default VNIC for this function.
         */
        #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT     UINT32_C(0x1)
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_vnic_alloc_output (size:128b/16B) */
struct hwrm_vnic_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Logical vnic ID */
        uint32_t        vnic_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************
 * hwrm_vnic_free *
 ******************/


/* hwrm_vnic_free_input (size:192b/24B) */
struct hwrm_vnic_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Logical vnic ID */
        uint32_t        vnic_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_vnic_free_output (size:128b/16B) */
struct hwrm_vnic_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************
 * hwrm_vnic_cfg *
 *****************/


/* hwrm_vnic_cfg_input (size:320b/40B) */
struct hwrm_vnic_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is '1', the VNIC is requested to
         * be the default VNIC for the function.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the VNIC is being configured to
         * strip VLAN in the RX path.
         * If set to '0', then VLAN stripping is disabled on
         * this VNIC.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the VNIC is being configured to
         * buffer receive packets in the hardware until the host
         * posts new receive buffers.
         * If set to '0', then bd_stall is being configured to be
         * disabled on this VNIC.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the VNIC is being configured to
         * receive both RoCE and non-RoCE traffic.
         * If set to '0', then this VNIC is not configured to be
         * operating in dual VNIC mode.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE \
                UINT32_C(0x8)
        /*
         * When this flag is set to '1', the VNIC is requested to
         * be configured to receive only RoCE traffic.
         * If this flag is set to '0', then this flag shall be
         * ignored by the HWRM.
         * If roce_dual_vnic_mode flag is set to '1'
         * or roce_mirroring_capable_vnic_mode flag to 1,
         * then the HWRM client shall not set this flag to '1'.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE \
                UINT32_C(0x10)
        /*
         * When a VNIC uses one destination ring group for certain
         * application (e.g. Receive Flow Steering) where
         * exact match is used to direct packets to a VNIC with one
         * destination ring group only, there is no need to configure
         * RSS indirection table for that VNIC as only one destination
         * ring group is used.
         *
         * This flag is used to enable a mode where
         * RSS is enabled in the VNIC using a RSS context
         * for computing RSS hash but the RSS indirection table is
         * not configured using hwrm_vnic_rss_cfg.
         *
         * If this mode is enabled, then the driver should not program
         * RSS indirection table for the RSS context that is used for
         * computing RSS hash only.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_RSS_DFLT_CR_MODE \
                UINT32_C(0x20)
        /*
         * When this bit is '1', the VNIC is being configured to
         * receive both RoCE and non-RoCE traffic, but forward only the
         * RoCE traffic further. Also, RoCE traffic can be mirrored to
         * L2 driver.
         */
        #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE \
                UINT32_C(0x40)
        uint32_t        enables;
        /*
         * This bit must be '1' for the dflt_ring_grp field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the rss_rule field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the cos_rule field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the lb_rule field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the mru field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the default_rx_ring_id field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_DEFAULT_RX_RING_ID \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the default_cmpl_ring_id field to be
         * configured.
         */
        #define HWRM_VNIC_CFG_INPUT_ENABLES_DEFAULT_CMPL_RING_ID \
                UINT32_C(0x40)
        /* Logical vnic ID */
        uint16_t        vnic_id;
        /*
         * Default Completion ring for the VNIC.  This ring will
         * be chosen if packet does not match any RSS rules and if
         * there is no COS rule.
         */
        uint16_t        dflt_ring_grp;
        /*
         * RSS ID for RSS rule/table structure.  0xFF... (All Fs) if
         * there is no RSS rule.
         */
        uint16_t        rss_rule;
        /*
         * RSS ID for COS rule/table structure.  0xFF... (All Fs) if
         * there is no COS rule.
         */
        uint16_t        cos_rule;
        /*
         * RSS ID for load balancing rule/table structure.
         * 0xFF... (All Fs) if there is no LB rule.
         */
        uint16_t        lb_rule;
        /*
         * The maximum receive unit of the vnic.
         * Each vnic is associated with a function.
         * The vnic mru value overwrites the mru setting of the
         * associated function.
         * The HWRM shall make sure that vnic mru does not exceed
         * the mru of the port the function is associated with.
         */
        uint16_t        mru;
        /*
         * Default Rx ring for the VNIC.  This ring will
         * be chosen if packet does not match any RSS rules.
         * The aggregation ring associated with the Rx ring is
         * implied based on the Rx ring specified when the
         * aggregation ring was allocated.
         */
        uint16_t        default_rx_ring_id;
        /*
         * Default completion ring for the VNIC.  This ring will
         * be chosen if packet does not match any RSS rules.
         */
        uint16_t        default_cmpl_ring_id;
} __attribute__((packed));

/* hwrm_vnic_cfg_output (size:128b/16B) */
struct hwrm_vnic_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************
 * hwrm_vnic_qcfg *
 ******************/


/* hwrm_vnic_qcfg_input (size:256b/32B) */
struct hwrm_vnic_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the vf_id_valid field to be
         * configured.
         */
        #define HWRM_VNIC_QCFG_INPUT_ENABLES_VF_ID_VALID     UINT32_C(0x1)
        /* Logical vnic ID */
        uint32_t        vnic_id;
        /* ID of Virtual Function whose VNIC resource is being queried. */
        uint16_t        vf_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_vnic_qcfg_output (size:256b/32B) */
struct hwrm_vnic_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Default Completion ring for the VNIC. */
        uint16_t        dflt_ring_grp;
        /*
         * RSS ID for RSS rule/table structure.  0xFF... (All Fs) if
         * there is no RSS rule.
         */
        uint16_t        rss_rule;
        /*
         * RSS ID for COS rule/table structure.  0xFF... (All Fs) if
         * there is no COS rule.
         */
        uint16_t        cos_rule;
        /*
         * RSS ID for load balancing rule/table structure.
         * 0xFF... (All Fs) if there is no LB rule.
         */
        uint16_t        lb_rule;
        /* The maximum receive unit of the vnic. */
        uint16_t        mru;
        uint8_t unused_0[2];
        uint32_t        flags;
        /*
         * When this bit is '1', the VNIC is the default VNIC for
         * the function.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_DEFAULT \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the VNIC is configured to
         * strip VLAN in the RX path.
         * If set to '0', then VLAN stripping is disabled on
         * this VNIC.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_VLAN_STRIP_MODE \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the VNIC is configured to
         * buffer receive packets in the hardware until the host
         * posts new receive buffers.
         * If set to '0', then bd_stall is disabled on
         * this VNIC.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_BD_STALL_MODE \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the VNIC is configured to
         * receive both RoCE and non-RoCE traffic.
         * If set to '0', then this VNIC is not configured to
         * operate in dual VNIC mode.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_DUAL_VNIC_MODE \
                UINT32_C(0x8)
        /*
         * When this flag is set to '1', the VNIC is configured to
         * receive only RoCE traffic.
         * When this flag is set to '0', the VNIC is not configured
         * to receive only RoCE traffic.
         * If roce_dual_vnic_mode flag and this flag both are set
         * to '1', then it is an invalid configuration of the
         * VNIC. The HWRM should not allow that type of
         * mis-configuration by HWRM clients.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_ONLY_VNIC_MODE \
                UINT32_C(0x10)
        /*
         * When a VNIC uses one destination ring group for certain
         * application (e.g. Receive Flow Steering) where
         * exact match is used to direct packets to a VNIC with one
         * destination ring group only, there is no need to configure
         * RSS indirection table for that VNIC as only one destination
         * ring group is used.
         *
         * When this bit is set to '1', then the VNIC is enabled in a
         * mode where RSS is enabled in the VNIC using a RSS context
         * for computing RSS hash but the RSS indirection table is
         * not configured.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_RSS_DFLT_CR_MODE \
                UINT32_C(0x20)
        /*
         * When this bit is '1', the VNIC is configured to
         * receive both RoCE and non-RoCE traffic, but forward only
         * RoCE traffic further. Also RoCE traffic can be mirrored to
         * L2 driver.
         */
        #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE \
                UINT32_C(0x40)
        uint8_t unused_1[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************
 * hwrm_vnic_qcaps *
 *******************/


/* hwrm_vnic_qcaps_input (size:192b/24B) */
struct hwrm_vnic_qcaps_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_vnic_qcaps_output (size:192b/24B) */
struct hwrm_vnic_qcaps_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The maximum receive unit that is settable on a vnic. */
        uint16_t        mru;
        uint8_t unused_0[2];
        uint32_t        flags;
        /* Unused. */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_UNUSED \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the capability of stripping VLAN in
         * the RX path is supported on VNIC(s).
         * If set to '0', then VLAN stripping capability is
         * not supported on VNIC(s).
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_VLAN_STRIP_CAP \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the capability to buffer receive
         * packets in the hardware until the host posts new receive buffers
         * is supported on VNIC(s).
         * If set to '0', then bd_stall capability is not supported
         * on VNIC(s).
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_BD_STALL_CAP \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the capability to
         * receive both RoCE and non-RoCE traffic on VNIC(s) is
         * supported.
         * If set to '0', then the capability to receive
         * both RoCE and non-RoCE traffic on VNIC(s) is
         * not supported.
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_DUAL_VNIC_CAP \
                UINT32_C(0x8)
        /*
         * When this bit is set to '1', the capability to configure
         * a VNIC to receive only RoCE traffic is supported.
         * When this flag is set to '0', the VNIC capability to
         * configure to receive only RoCE traffic is not supported.
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_ONLY_VNIC_CAP \
                UINT32_C(0x10)
        /*
         * When this bit is set to '1', then the capability to enable
         * a VNIC in a mode where RSS context without configuring
         * RSS indirection table is supported (for RSS hash computation).
         * When this bit is set to '0', then a VNIC can not be configured
         * with a mode to enable RSS context without configuring RSS
         * indirection table.
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_RSS_DFLT_CR_CAP \
                UINT32_C(0x20)
        /*
         * When this bit is '1', the capability to
         * mirror the the RoCE traffic is supported.
         * If set to '0', then the capability to mirror the
         * RoCE traffic is not supported.
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_CAP \
                UINT32_C(0x40)
        /*
         * When this bit is '1', the outermost RSS hashing capability
         * is supported. If set to '0', then the outermost RSS hashing
         * capability is not supported.
         */
        #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_OUTERMOST_RSS_CAP \
                UINT32_C(0x80)
        uint8_t unused_1[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_vnic_tpa_cfg *
 *********************/


/* hwrm_vnic_tpa_cfg_input (size:320b/40B) */
struct hwrm_vnic_tpa_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is '1', the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) of
         * non-tunneled TCP packets.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_TPA \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) of
         * tunneled TCP packets.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_ENCAP_TPA \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) according
         * to Windows Receive Segment Coalescing (RSC) rules.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_RSC_WND_UPDATE \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) according
         * to Linux Generic Receive Offload (GRO) rules.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO \
                UINT32_C(0x8)
        /*
         * When this bit is '1', the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) for TCP
         * packets with IP ECN set to non-zero.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_ECN \
                UINT32_C(0x10)
        /*
         * When this bit is '1', the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) for
         * GRE tunneled TCP packets only if all packets have the
         * same GRE sequence.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ \
                UINT32_C(0x20)
        /*
         * When this bit is '1' and the GRO mode is enabled,
         * the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) for
         * TCP/IPv4 packets with consecutively increasing IPIDs.
         * In other words, the last packet that is being
         * aggregated to an already existing aggregation context
         * shall have IPID 1 more than the IPID of the last packet
         * that was aggregated in that aggregation context.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_IPID_CHECK \
                UINT32_C(0x40)
        /*
         * When this bit is '1' and the GRO mode is enabled,
         * the VNIC shall be configured to
         * perform transparent packet aggregation (TPA) for
         * TCP packets with the same TTL (IPv4) or Hop limit (IPv6)
         * value.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_TTL_CHECK \
                UINT32_C(0x80)
        uint32_t        enables;
        /*
         * This bit must be '1' for the max_agg_segs field to be
         * configured.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_SEGS      UINT32_C(0x1)
        /*
         * This bit must be '1' for the max_aggs field to be
         * configured.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGGS          UINT32_C(0x2)
        /*
         * This bit must be '1' for the max_agg_timer field to be
         * configured.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_TIMER     UINT32_C(0x4)
        /*
         * This bit must be '1' for the min_agg_len field to be
         * configured.
         */
        #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MIN_AGG_LEN       UINT32_C(0x8)
        /* Logical vnic ID */
        uint16_t        vnic_id;
        /*
         * This is the maximum number of TCP segments that can
         * be aggregated (unit is Log2). Max value is 31.
         */
        uint16_t        max_agg_segs;
        /* 1 segment */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_1   UINT32_C(0x0)
        /* 2 segments */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_2   UINT32_C(0x1)
        /* 4 segments */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_4   UINT32_C(0x2)
        /* 8 segments */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_8   UINT32_C(0x3)
        /* Any segment size larger than this is not valid */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX UINT32_C(0x1f)
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_LAST \
                HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX
        /*
         * This is the maximum number of aggregations this VNIC is
         * allowed (unit is Log2). Max value is 7
         */
        uint16_t        max_aggs;
        /* 1 aggregation */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_1   UINT32_C(0x0)
        /* 2 aggregations */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_2   UINT32_C(0x1)
        /* 4 aggregations */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_4   UINT32_C(0x2)
        /* 8 aggregations */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_8   UINT32_C(0x3)
        /* 16 aggregations */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_16  UINT32_C(0x4)
        /* Any aggregation size larger than this is not valid */
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX UINT32_C(0x7)
        #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_LAST \
                HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX
        uint8_t unused_0[2];
        /*
         * This is the maximum amount of time allowed for
         * an aggregation context to complete after it was initiated.
         */
        uint32_t        max_agg_timer;
        /*
         * This is the minimum amount of payload length required to
         * start an aggregation context.
         */
        uint32_t        min_agg_len;
} __attribute__((packed));

/* hwrm_vnic_tpa_cfg_output (size:128b/16B) */
struct hwrm_vnic_tpa_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_vnic_tpa_qcfg *
 **********************/


/* hwrm_vnic_tpa_qcfg_input (size:192b/24B) */
struct hwrm_vnic_tpa_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Logical vnic ID */
        uint16_t        vnic_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_vnic_tpa_qcfg_output (size:256b/32B) */
struct hwrm_vnic_tpa_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint32_t        flags;
        /*
         * When this bit is '1', the VNIC is configured to
         * perform transparent packet aggregation (TPA) of
         * non-tunneled TCP packets.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_TPA \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the VNIC is configured to
         * perform transparent packet aggregation (TPA) of
         * tunneled TCP packets.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_ENCAP_TPA \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the VNIC is configured to
         * perform transparent packet aggregation (TPA) according
         * to Windows Receive Segment Coalescing (RSC) rules.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_RSC_WND_UPDATE \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the VNIC is configured to
         * perform transparent packet aggregation (TPA) according
         * to Linux Generic Receive Offload (GRO) rules.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_GRO \
                UINT32_C(0x8)
        /*
         * When this bit is '1', the VNIC is configured to
         * perform transparent packet aggregation (TPA) for TCP
         * packets with IP ECN set to non-zero.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_AGG_WITH_ECN \
                UINT32_C(0x10)
        /*
         * When this bit is '1', the VNIC is configured to
         * perform transparent packet aggregation (TPA) for
         * GRE tunneled TCP packets only if all packets have the
         * same GRE sequence.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ \
                UINT32_C(0x20)
        /*
         * When this bit is '1' and the GRO mode is enabled,
         * the VNIC is configured to
         * perform transparent packet aggregation (TPA) for
         * TCP/IPv4 packets with consecutively increasing IPIDs.
         * In other words, the last packet that is being
         * aggregated to an already existing aggregation context
         * shall have IPID 1 more than the IPID of the last packet
         * that was aggregated in that aggregation context.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_GRO_IPID_CHECK \
                UINT32_C(0x40)
        /*
         * When this bit is '1' and the GRO mode is enabled,
         * the VNIC is configured to
         * perform transparent packet aggregation (TPA) for
         * TCP packets with the same TTL (IPv4) or Hop limit (IPv6)
         * value.
         */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_FLAGS_GRO_TTL_CHECK \
                UINT32_C(0x80)
        /*
         * This is the maximum number of TCP segments that can
         * be aggregated (unit is Log2). Max value is 31.
         */
        uint16_t        max_agg_segs;
        /* 1 segment */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_1   UINT32_C(0x0)
        /* 2 segments */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_2   UINT32_C(0x1)
        /* 4 segments */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_4   UINT32_C(0x2)
        /* 8 segments */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_8   UINT32_C(0x3)
        /* Any segment size larger than this is not valid */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_MAX UINT32_C(0x1f)
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_LAST \
                HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGG_SEGS_MAX
        /*
         * This is the maximum number of aggregations this VNIC is
         * allowed (unit is Log2). Max value is 7
         */
        uint16_t        max_aggs;
        /* 1 aggregation */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_1   UINT32_C(0x0)
        /* 2 aggregations */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_2   UINT32_C(0x1)
        /* 4 aggregations */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_4   UINT32_C(0x2)
        /* 8 aggregations */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_8   UINT32_C(0x3)
        /* 16 aggregations */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_16  UINT32_C(0x4)
        /* Any aggregation size larger than this is not valid */
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_MAX UINT32_C(0x7)
        #define HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_LAST \
                HWRM_VNIC_TPA_QCFG_OUTPUT_MAX_AGGS_MAX
        /*
         * This is the maximum amount of time allowed for
         * an aggregation context to complete after it was initiated.
         */
        uint32_t        max_agg_timer;
        /*
         * This is the minimum amount of payload length required to
         * start an aggregation context.
         */
        uint32_t        min_agg_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_vnic_rss_cfg *
 *********************/


/* hwrm_vnic_rss_cfg_input (size:384b/48B) */
struct hwrm_vnic_rss_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        hash_type;
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source and destination IPv4 addresses of IPv4
         * packets.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4         UINT32_C(0x1)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv4 addresses and
         * source/destination ports of TCP/IPv4 packets.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4     UINT32_C(0x2)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv4 addresses and
         * source/destination ports of UDP/IPv4 packets.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4     UINT32_C(0x4)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source and destination IPv4 addresses of IPv6
         * packets.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6         UINT32_C(0x8)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv6 addresses and
         * source/destination ports of TCP/IPv6 packets.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6     UINT32_C(0x10)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv6 addresses and
         * source/destination ports of UDP/IPv6 packets.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6     UINT32_C(0x20)
        /* VNIC ID of VNIC associated with RSS table being configured. */
        uint16_t        vnic_id;
        /*
         * Specifies which VNIC ring table pair to configure.
         * Valid values range from 0 to 7.
         */
        uint8_t ring_table_pair_index;
        /* Flags to specify different RSS hash modes. */
        uint8_t hash_mode_flags;
        /*
         * When this bit is '1', it indicates using current RSS
         * hash mode setting configured in the device.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_DEFAULT \
                UINT32_C(0x1)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over innermost 4 tuples {l3.src, l3.dest,
         * l4.src, l4.dest} for tunnel packets. For none-tunnel
         * packets, the RSS hash is computed over the normal
         * src/dest l3 and src/dest l4 headers.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_INNERMOST_4 \
                UINT32_C(0x2)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over innermost 2 tuples {l3.src, l3.dest} for
         * tunnel packets. For none-tunnel packets, the RSS hash is
         * computed over the normal src/dest l3 headers.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_INNERMOST_2 \
                UINT32_C(0x4)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over outermost 4 tuples {t_l3.src, t_l3.dest,
         * t_l4.src, t_l4.dest} for tunnel packets. For none-tunnel
         * packets, the RSS hash is computed over the normal
         * src/dest l3 and src/dest l4 headers.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_OUTERMOST_4 \
                UINT32_C(0x8)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over outermost 2 tuples {t_l3.src, t_l3.dest} for
         * tunnel packets. For none-tunnel packets, the RSS hash is
         * computed over the normal src/dest l3 headers.
         */
        #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_OUTERMOST_2 \
                UINT32_C(0x10)
        /* This is the address for rss ring group table */
        uint64_t        ring_grp_tbl_addr;
        /* This is the address for rss hash key table */
        uint64_t        hash_key_tbl_addr;
        /* Index to the rss indirection table. */
        uint16_t        rss_ctx_idx;
        uint8_t unused_1[6];
} __attribute__((packed));

/* hwrm_vnic_rss_cfg_output (size:128b/16B) */
struct hwrm_vnic_rss_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_vnic_rss_qcfg *
 **********************/


/* hwrm_vnic_rss_qcfg_input (size:192b/24B) */
struct hwrm_vnic_rss_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Index to the rss indirection table. */
        uint16_t        rss_ctx_idx;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_vnic_rss_qcfg_output (size:512b/64B) */
struct hwrm_vnic_rss_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint32_t        hash_type;
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source and destination IPv4 addresses of IPv4
         * packets.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_IPV4         UINT32_C(0x1)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv4 addresses and
         * source/destination ports of TCP/IPv4 packets.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_TCP_IPV4     UINT32_C(0x2)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv4 addresses and
         * source/destination ports of UDP/IPv4 packets.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_UDP_IPV4     UINT32_C(0x4)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source and destination IPv4 addresses of IPv6
         * packets.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_IPV6         UINT32_C(0x8)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv6 addresses and
         * source/destination ports of TCP/IPv6 packets.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_TCP_IPV6     UINT32_C(0x10)
        /*
         * When this bit is '1', the RSS hash shall be computed
         * over source/destination IPv6 addresses and
         * source/destination ports of UDP/IPv6 packets.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_UDP_IPV6     UINT32_C(0x20)
        uint8_t unused_0[4];
        /* This is the value of rss hash key */
        uint32_t        hash_key[10];
        /* Flags to specify different RSS hash modes. */
        uint8_t hash_mode_flags;
        /*
         * When this bit is '1', it indicates using current RSS
         * hash mode setting configured in the device.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_DEFAULT \
                UINT32_C(0x1)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over innermost 4 tuples {l3.src, l3.dest,
         * l4.src, l4.dest} for tunnel packets. For none-tunnel
         * packets, the RSS hash is computed over the normal
         * src/dest l3 and src/dest l4 headers.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_INNERMOST_4 \
                UINT32_C(0x2)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over innermost 2 tuples {l3.src, l3.dest} for
         * tunnel packets. For none-tunnel packets, the RSS hash is
         * computed over the normal src/dest l3 headers.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_INNERMOST_2 \
                UINT32_C(0x4)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over outermost 4 tuples {t_l3.src, t_l3.dest,
         * t_l4.src, t_l4.dest} for tunnel packets. For none-tunnel
         * packets, the RSS hash is computed over the normal
         * src/dest l3 and src/dest l4 headers.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_OUTERMOST_4 \
                UINT32_C(0x8)
        /*
         * When this bit is '1', it indicates requesting support of
         * RSS hashing over outermost 2 tuples {t_l3.src, t_l3.dest} for
         * tunnel packets. For none-tunnel packets, the RSS hash is
         * computed over the normal src/dest l3 headers.
         */
        #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_OUTERMOST_2 \
                UINT32_C(0x10)
        uint8_t unused_1[6];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_vnic_plcmodes_cfg *
 **************************/


/* hwrm_vnic_plcmodes_cfg_input (size:320b/40B) */
struct hwrm_vnic_plcmodes_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * When this bit is '1', the VNIC shall be configured to
         * use regular placement algorithm.
         * By default, the regular placement algorithm shall be
         * enabled on the VNIC.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_REGULAR_PLACEMENT \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the VNIC shall be configured
         * use the jumbo placement algorithm.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_JUMBO_PLACEMENT \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the VNIC shall be configured
         * to enable Header-Data split for IPv4 packets according
         * to the following rules:
         * # If the packet is identified as TCP/IPv4, then the
         * packet is split at the beginning of the TCP payload.
         * # If the packet is identified as UDP/IPv4, then the
         * packet is split at the beginning of UDP payload.
         * # If the packet is identified as non-TCP and non-UDP
         * IPv4 packet, then the packet is split at the beginning
         * of the upper layer protocol header carried in the IPv4
         * packet.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV4 \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the VNIC shall be configured
         * to enable Header-Data split for IPv6 packets according
         * to the following rules:
         * # If the packet is identified as TCP/IPv6, then the
         * packet is split at the beginning of the TCP payload.
         * # If the packet is identified as UDP/IPv6, then the
         * packet is split at the beginning of UDP payload.
         * # If the packet is identified as non-TCP and non-UDP
         * IPv6 packet, then the packet is split at the beginning
         * of the upper layer protocol header carried in the IPv6
         * packet.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV6 \
                UINT32_C(0x8)
        /*
         * When this bit is '1', the VNIC shall be configured
         * to enable Header-Data split for FCoE packets at the
         * beginning of FC payload.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_FCOE \
                UINT32_C(0x10)
        /*
         * When this bit is '1', the VNIC shall be configured
         * to enable Header-Data split for RoCE packets at the
         * beginning of RoCE payload (after BTH/GRH headers).
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_ROCE \
                UINT32_C(0x20)
        uint32_t        enables;
        /*
         * This bit must be '1' for the jumbo_thresh_valid field to be
         * configured.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_JUMBO_THRESH_VALID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the hds_offset_valid field to be
         * configured.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_OFFSET_VALID \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the hds_threshold_valid field to be
         * configured.
         */
        #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_THRESHOLD_VALID \
                UINT32_C(0x4)
        /* Logical vnic ID */
        uint32_t        vnic_id;
        /*
         * When jumbo placement algorithm is enabled, this value
         * is used to determine the threshold for jumbo placement.
         * Packets with length larger than this value will be
         * placed according to the jumbo placement algorithm.
         */
        uint16_t        jumbo_thresh;
        /*
         * This value is used to determine the offset into
         * packet buffer where the split data (payload) will be
         * placed according to one of of HDS placement algorithm.
         *
         * The lengths of packet buffers provided for split data
         * shall be larger than this value.
         */
        uint16_t        hds_offset;
        /*
         * When one of the HDS placement algorithm is enabled, this
         * value is used to determine the threshold for HDS
         * placement.
         * Packets with length larger than this value will be
         * placed according to the HDS placement algorithm.
         * This value shall be in multiple of 4 bytes.
         */
        uint16_t        hds_threshold;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_vnic_plcmodes_cfg_output (size:128b/16B) */
struct hwrm_vnic_plcmodes_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_vnic_plcmodes_qcfg *
 ***************************/


/* hwrm_vnic_plcmodes_qcfg_input (size:192b/24B) */
struct hwrm_vnic_plcmodes_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Logical vnic ID */
        uint32_t        vnic_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_vnic_plcmodes_qcfg_output (size:192b/24B) */
struct hwrm_vnic_plcmodes_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint32_t        flags;
        /*
         * When this bit is '1', the VNIC is configured to
         * use regular placement algorithm.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_REGULAR_PLACEMENT \
                UINT32_C(0x1)
        /*
         * When this bit is '1', the VNIC is configured to
         * use the jumbo placement algorithm.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_JUMBO_PLACEMENT \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the VNIC is configured
         * to enable Header-Data split for IPv4 packets.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV4 \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the VNIC is configured
         * to enable Header-Data split for IPv6 packets.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV6 \
                UINT32_C(0x8)
        /*
         * When this bit is '1', the VNIC is configured
         * to enable Header-Data split for FCoE packets.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_FCOE \
                UINT32_C(0x10)
        /*
         * When this bit is '1', the VNIC is configured
         * to enable Header-Data split for RoCE packets.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_ROCE \
                UINT32_C(0x20)
        /*
         * When this bit is '1', the VNIC is configured
         * to be the default VNIC of the requesting function.
         */
        #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_DFLT_VNIC \
                UINT32_C(0x40)
        /*
         * When jumbo placement algorithm is enabled, this value
         * is used to determine the threshold for jumbo placement.
         * Packets with length larger than this value will be
         * placed according to the jumbo placement algorithm.
         */
        uint16_t        jumbo_thresh;
        /*
         * This value is used to determine the offset into
         * packet buffer where the split data (payload) will be
         * placed according to one of of HDS placement algorithm.
         *
         * The lengths of packet buffers provided for split data
         * shall be larger than this value.
         */
        uint16_t        hds_offset;
        /*
         * When one of the HDS placement algorithm is enabled, this
         * value is used to determine the threshold for HDS
         * placement.
         * Packets with length larger than this value will be
         * placed according to the HDS placement algorithm.
         * This value shall be in multiple of 4 bytes.
         */
        uint16_t        hds_threshold;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************************
 * hwrm_vnic_rss_cos_lb_ctx_alloc *
 **********************************/


/* hwrm_vnic_rss_cos_lb_ctx_alloc_input (size:128b/16B) */
struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_vnic_rss_cos_lb_ctx_alloc_output (size:128b/16B) */
struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* rss_cos_lb_ctx_id is 16 b */
        uint16_t        rss_cos_lb_ctx_id;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************************
 * hwrm_vnic_rss_cos_lb_ctx_free *
 *********************************/


/* hwrm_vnic_rss_cos_lb_ctx_free_input (size:192b/24B) */
struct hwrm_vnic_rss_cos_lb_ctx_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* rss_cos_lb_ctx_id is 16 b */
        uint16_t        rss_cos_lb_ctx_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_vnic_rss_cos_lb_ctx_free_output (size:128b/16B) */
struct hwrm_vnic_rss_cos_lb_ctx_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************
 * hwrm_ring_alloc *
 *******************/


/* hwrm_ring_alloc_input (size:640b/80B) */
struct hwrm_ring_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the ring_arb_cfg field to be
         * configured.
         */
        #define HWRM_RING_ALLOC_INPUT_ENABLES_RING_ARB_CFG \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the stat_ctx_id_valid field to be
         * configured.
         */
        #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the max_bw_valid field to be
         * configured.
         */
        #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the rx_ring_id field to be
         * configured.
         */
        #define HWRM_RING_ALLOC_INPUT_ENABLES_RX_RING_ID_VALID \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the nq_ring_id field to be
         * configured.
         */
        #define HWRM_RING_ALLOC_INPUT_ENABLES_NQ_RING_ID_VALID \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the rx_buf_size field to be
         * configured.
         */
        #define HWRM_RING_ALLOC_INPUT_ENABLES_RX_BUF_SIZE_VALID \
                UINT32_C(0x100)
        /* Ring Type. */
        uint8_t ring_type;
        /* L2 Completion Ring (CR) */
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_L2_CMPL   UINT32_C(0x0)
        /* TX Ring (TR) */
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX        UINT32_C(0x1)
        /* RX Ring (RR) */
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX        UINT32_C(0x2)
        /* RoCE Notification Completion Ring (ROCE_CR) */
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
        /* RX Aggregation Ring */
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX_AGG    UINT32_C(0x4)
        /* Notification Queue */
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_NQ        UINT32_C(0x5)
        #define HWRM_RING_ALLOC_INPUT_RING_TYPE_LAST \
                HWRM_RING_ALLOC_INPUT_RING_TYPE_NQ
        uint8_t unused_0[3];
        /*
         * This value is a pointer to the page table for the
         * Ring.
         */
        uint64_t        page_tbl_addr;
        /* First Byte Offset of the first entry in the first page. */
        uint32_t        fbo;
        /*
         * Actual page size in 2^page_size. The supported range is increments
         * in powers of 2 from 16 bytes to 1GB.
         * - 4 = 16 B
         *     Page size is 16 B.
         * - 12 = 4 KB
         *     Page size is 4 KB.
         * - 13 = 8 KB
         *     Page size is 8 KB.
         * - 16 = 64 KB
         *     Page size is 64 KB.
         * - 21 = 2 MB
         *     Page size is 2 MB.
         * - 22 = 4 MB
         *     Page size is 4 MB.
         * - 30 = 1 GB
         *     Page size is 1 GB.
         */
        uint8_t page_size;
        /*
         * This value indicates the depth of page table.
         * For this version of the specification, value other than 0 or
         * 1 shall be considered as an invalid value.
         * When the page_tbl_depth = 0, then it is treated as a
         * special case with the following.
         * 1. FBO and page size fields are not valid.
         * 2. page_tbl_addr is the physical address of the first
         *    element of the ring.
         */
        uint8_t page_tbl_depth;
        uint8_t unused_1[2];
        /*
         * Number of 16B units in the ring.  Minimum size for
         * a ring is 16 16B entries.
         */
        uint32_t        length;
        /*
         * Logical ring number for the ring to be allocated.
         * This value determines the position in the doorbell
         * area where the update to the ring will be made.
         *
         * For completion rings, this value is also the MSI-X
         * vector number for the function the completion ring is
         * associated with.
         */
        uint16_t        logical_id;
        /*
         * This field is used only when ring_type is a TX ring.
         * This value indicates what completion ring the TX ring
         * is associated with.
         */
        uint16_t        cmpl_ring_id;
        /*
         * This field is used only when ring_type is a TX ring.
         * This value indicates what CoS queue the TX ring
         * is associated with.
         */
        uint16_t        queue_id;
        /*
         * When allocating a Rx ring or Rx aggregation ring, this field
         * specifies the size of the buffer descriptors posted to the ring.
         */
        uint16_t        rx_buf_size;
        /*
         * When allocating an Rx aggregation ring, this field
         * specifies the associated Rx ring ID.
         */
        uint16_t        rx_ring_id;
        /*
         * When allocating a completion ring, this field
         * specifies the associated NQ ring ID.
         */
        uint16_t        nq_ring_id;
        /*
         * This field is used only when ring_type is a TX ring.
         * This field is used to configure arbitration related
         * parameters for a TX ring.
         */
        uint16_t        ring_arb_cfg;
        /* Arbitration policy used for the ring. */
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_MASK \
                UINT32_C(0xf)
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SFT       0
        /*
         * Use strict priority for the TX ring.
         * Priority value is specified in arb_policy_param
         */
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SP \
                UINT32_C(0x1)
        /*
         * Use weighted fair queue arbitration for the TX ring.
         * Weight is specified in arb_policy_param
         */
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ \
                UINT32_C(0x2)
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_LAST \
                HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ
        /* Reserved field. */
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_MASK \
                UINT32_C(0xf0)
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_SFT             4
        /*
         * Arbitration policy specific parameter.
         * # For strict priority arbitration policy, this field
         * represents a priority value. If set to 0, then the priority
         * is not specified and the HWRM is allowed to select
         * any priority for this TX ring.
         * # For weighted fair queue arbitration policy, this field
         * represents a weight value. If set to 0, then the weight
         * is not specified and the HWRM is allowed to select
         * any weight for this TX ring.
         */
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_MASK \
                UINT32_C(0xff00)
        #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_SFT 8
        uint16_t        unused_3;
        /*
         * This field is reserved for the future use.
         * It shall be set to 0.
         */
        uint32_t        reserved3;
        /*
         * This field is used only when ring_type is a TX ring.
         * This input indicates what statistics context this ring
         * should be associated with.
         */
        uint32_t        stat_ctx_id;
        /*
         * This field is reserved for the future use.
         * It shall be set to 0.
         */
        uint32_t        reserved4;
        /*
         * This field is used only when ring_type is a TX ring
         * to specify maximum BW allocated to the TX ring.
         * The HWRM will translate this value into byte counter and
         * time interval used for this ring inside the device.
         */
        uint32_t        max_bw;
        /* The bandwidth value. */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_SFT              0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_LAST \
                HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_SFT         29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
                HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
        /*
         * This field is used only when ring_type is a Completion ring.
         * This value indicates what interrupt mode should be used
         * on this completion ring.
         * Note: In the legacy interrupt mode, no more than 16
         * completion rings are allowed.
         */
        uint8_t int_mode;
        /* Legacy INTA */
        #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY UINT32_C(0x0)
        /* Reserved */
        #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD   UINT32_C(0x1)
        /* MSI-X */
        #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX   UINT32_C(0x2)
        /* No Interrupt - Polled mode */
        #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL   UINT32_C(0x3)
        #define HWRM_RING_ALLOC_INPUT_INT_MODE_LAST \
                HWRM_RING_ALLOC_INPUT_INT_MODE_POLL
        uint8_t unused_4[3];
} __attribute__((packed));

/* hwrm_ring_alloc_output (size:128b/16B) */
struct hwrm_ring_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * Physical number of ring allocated.
         * This value shall be unique for a ring type.
         */
        uint16_t        ring_id;
        /* Logical number of ring allocated. */
        uint16_t        logical_ring_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************
 * hwrm_ring_free *
 ******************/


/* hwrm_ring_free_input (size:192b/24B) */
struct hwrm_ring_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Ring Type. */
        uint8_t ring_type;
        /* L2 Completion Ring (CR) */
        #define HWRM_RING_FREE_INPUT_RING_TYPE_L2_CMPL   UINT32_C(0x0)
        /* TX Ring (TR) */
        #define HWRM_RING_FREE_INPUT_RING_TYPE_TX        UINT32_C(0x1)
        /* RX Ring (RR) */
        #define HWRM_RING_FREE_INPUT_RING_TYPE_RX        UINT32_C(0x2)
        /* RoCE Notification Completion Ring (ROCE_CR) */
        #define HWRM_RING_FREE_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
        /* RX Aggregation Ring */
        #define HWRM_RING_FREE_INPUT_RING_TYPE_RX_AGG    UINT32_C(0x4)
        /* Notification Queue */
        #define HWRM_RING_FREE_INPUT_RING_TYPE_NQ        UINT32_C(0x5)
        #define HWRM_RING_FREE_INPUT_RING_TYPE_LAST \
                HWRM_RING_FREE_INPUT_RING_TYPE_NQ
        uint8_t unused_0;
        /* Physical number of ring allocated. */
        uint16_t        ring_id;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_ring_free_output (size:128b/16B) */
struct hwrm_ring_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************************
 * hwrm_ring_cmpl_ring_qaggint_params *
 **************************************/


/* hwrm_ring_cmpl_ring_qaggint_params_input (size:192b/24B) */
struct hwrm_ring_cmpl_ring_qaggint_params_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Physical number of completion ring. */
        uint16_t        ring_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_ring_cmpl_ring_qaggint_params_output (size:256b/32B) */
struct hwrm_ring_cmpl_ring_qaggint_params_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint16_t        flags;
        /*
         * When this bit is set to '1', interrupt max
         * timer is reset whenever a completion is received.
         */
        #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_TIMER_RESET \
                UINT32_C(0x1)
        /*
         * When this bit is set to '1', ring idle mode
         * aggregation will be enabled.
         */
        #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_RING_IDLE \
                UINT32_C(0x2)
        /*
         * Number of completions to aggregate before DMA
         * during the normal mode.
         */
        uint16_t        num_cmpl_dma_aggr;
        /*
         * Number of completions to aggregate before DMA
         * during the interrupt mode.
         */
        uint16_t        num_cmpl_dma_aggr_during_int;
        /*
         * Timer in unit of 80-nsec used to aggregate completions before
         * DMA during the normal mode (not in interrupt mode).
         */
        uint16_t        cmpl_aggr_dma_tmr;
        /*
         * Timer in unit of 80-nsec used to aggregate completions before
         * DMA during the interrupt mode.
         */
        uint16_t        cmpl_aggr_dma_tmr_during_int;
        /* Minimum time (in unit of 80-nsec) between two interrupts. */
        uint16_t        int_lat_tmr_min;
        /*
         * Maximum wait time (in unit of 80-nsec) spent aggregating
         * completions before signaling the interrupt after the
         * interrupt is enabled.
         */
        uint16_t        int_lat_tmr_max;
        /*
         * Minimum number of completions aggregated before signaling
         * an interrupt.
         */
        uint16_t        num_cmpl_aggr_int;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************************************
 * hwrm_ring_cmpl_ring_cfg_aggint_params *
 *****************************************/


/* hwrm_ring_cmpl_ring_cfg_aggint_params_input (size:320b/40B) */
struct hwrm_ring_cmpl_ring_cfg_aggint_params_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Physical number of completion ring. */
        uint16_t        ring_id;
        uint16_t        flags;
        /*
         * When this bit is set to '1', interrupt latency max
         * timer is reset whenever a completion is received.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_TIMER_RESET \
                UINT32_C(0x1)
        /*
         * When this bit is set to '1', ring idle mode
         * aggregation will be enabled.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_RING_IDLE \
                UINT32_C(0x2)
        /*
         * Set this flag to 1 when configuring parameters on a
         * notification queue. Set this flag to 0 when configuring
         * parameters on a completion queue.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_IS_NQ \
                UINT32_C(0x4)
        /*
         * Number of completions to aggregate before DMA
         * during the normal mode.
         */
        uint16_t        num_cmpl_dma_aggr;
        /*
         * Number of completions to aggregate before DMA
         * during the interrupt mode.
         */
        uint16_t        num_cmpl_dma_aggr_during_int;
        /*
         * Timer in unit of 80-nsec used to aggregate completions before
         * DMA during the normal mode (not in interrupt mode).
         */
        uint16_t        cmpl_aggr_dma_tmr;
        /*
         * Timer in unit of 80-nsec used to aggregate completions before
         * DMA during the interrupt mode.
         */
        uint16_t        cmpl_aggr_dma_tmr_during_int;
        /* Minimum time (in unit of 80-nsec) between two interrupts. */
        uint16_t        int_lat_tmr_min;
        /*
         * Maximum wait time (in unit of 80-nsec) spent aggregating
         * cmpls before signaling the interrupt after the
         * interrupt is enabled.
         */
        uint16_t        int_lat_tmr_max;
        /*
         * Minimum number of completions aggregated before signaling
         * an interrupt.
         */
        uint16_t        num_cmpl_aggr_int;
        /*
         * Bitfield that indicates which parameters are to be applied. Only
         * required when configuring devices with notification queues, and
         * used in that case to set certain parameters on completion queues
         * and others on notification queues.
         */
        uint16_t        enables;
        /*
         * This bit must be '1' for the num_cmpl_dma_aggr field to be
         * configured.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_NUM_CMPL_DMA_AGGR \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the num_cmpl_dma_aggr_during_int field to be
         * configured.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_NUM_CMPL_DMA_AGGR_DURING_INT \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the cmpl_aggr_dma_tmr field to be
         * configured.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_CMPL_AGGR_DMA_TMR \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the int_lat_tmr_min field to be
         * configured.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_INT_LAT_TMR_MIN \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the int_lat_tmr_max field to be
         * configured.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_INT_LAT_TMR_MAX \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the num_cmpl_aggr_int field to be
         * configured.
         */
        #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_NUM_CMPL_AGGR_INT \
                UINT32_C(0x20)
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_ring_cmpl_ring_cfg_aggint_params_output (size:128b/16B) */
struct hwrm_ring_cmpl_ring_cfg_aggint_params_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************
 * hwrm_ring_reset *
 *******************/


/* hwrm_ring_reset_input (size:192b/24B) */
struct hwrm_ring_reset_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Ring Type. */
        uint8_t ring_type;
        /* L2 Completion Ring (CR) */
        #define HWRM_RING_RESET_INPUT_RING_TYPE_L2_CMPL   UINT32_C(0x0)
        /* TX Ring (TR) */
        #define HWRM_RING_RESET_INPUT_RING_TYPE_TX        UINT32_C(0x1)
        /* RX Ring (RR) */
        #define HWRM_RING_RESET_INPUT_RING_TYPE_RX        UINT32_C(0x2)
        /* RoCE Notification Completion Ring (ROCE_CR) */
        #define HWRM_RING_RESET_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
        #define HWRM_RING_RESET_INPUT_RING_TYPE_LAST \
                HWRM_RING_RESET_INPUT_RING_TYPE_ROCE_CMPL
        uint8_t unused_0;
        /* Physical number of the ring. */
        uint16_t        ring_id;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_ring_reset_output (size:128b/16B) */
struct hwrm_ring_reset_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_ring_grp_alloc *
 ***********************/


/* hwrm_ring_grp_alloc_input (size:192b/24B) */
struct hwrm_ring_grp_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This value identifies the CR associated with the ring
         * group.
         */
        uint16_t        cr;
        /*
         * This value identifies the main RR associated with the ring
         * group.
         */
        uint16_t        rr;
        /*
         * This value identifies the aggregation RR associated with
         * the ring group.  If this value is 0xFF... (All Fs), then no
         * Aggregation ring will be set.
         */
        uint16_t        ar;
        /*
         * This value identifies the statistics context associated
         * with the ring group.
         */
        uint16_t        sc;
} __attribute__((packed));

/* hwrm_ring_grp_alloc_output (size:128b/16B) */
struct hwrm_ring_grp_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This is the ring group ID value.  Use this value to program
         * the default ring group for the VNIC or as table entries
         * in an RSS/COS context.
         */
        uint32_t        ring_group_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_ring_grp_free *
 **********************/


/* hwrm_ring_grp_free_input (size:192b/24B) */
struct hwrm_ring_grp_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This is the ring group ID value. */
        uint32_t        ring_group_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_ring_grp_free_output (size:128b/16B) */
struct hwrm_ring_grp_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/****************************
 * hwrm_cfa_l2_filter_alloc *
 ****************************/


/* hwrm_cfa_l2_filter_alloc_input (size:768b/96B) */
struct hwrm_cfa_l2_filter_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH \
                UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX \
                UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX \
                UINT32_C(0x1)
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX
        /* Setting of this flag indicates the applicability to the loopback path. */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
                UINT32_C(0x2)
        /*
         * Setting of this flag indicates drop action. If this flag is not set,
         * then it should be considered accept action.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP \
                UINT32_C(0x4)
        /*
         * If this flag is set, all t_l2_* fields are invalid
         * and they should not be specified.
         * If this flag is set, then l2_* fields refer to
         * fields of outermost L2 header.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST \
                UINT32_C(0x8)
        uint32_t        enables;
        /*
         * This bit must be '1' for the l2_addr field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the l2_addr_mask field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the l2_ovlan field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the l2_ovlan_mask field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the l2_ivlan field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the l2_ivlan_mask field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the t_l2_addr field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the t_l2_addr_mask field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the t_l2_ovlan field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the t_l2_ovlan_mask field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the t_l2_ivlan field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the t_l2_ivlan_mask field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the src_type field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the src_id field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the tunnel_type field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the dst_id field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
                UINT32_C(0x8000)
        /*
         * This bit must be '1' for the mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
                UINT32_C(0x10000)
        /*
         * This value sets the match value for the L2 MAC address.
         * Destination MAC address for RX path.
         * Source MAC address for TX path.
         */
        uint8_t l2_addr[6];
        uint8_t unused_0[2];
        /*
         * This value sets the mask value for the L2 address.
         * A value of 0 will mask the corresponding bit from
         * compare.
         */
        uint8_t l2_addr_mask[6];
        /* This value sets VLAN ID value for outer VLAN. */
        uint16_t        l2_ovlan;
        /*
         * This value sets the mask value for the ovlan id.
         * A value of 0 will mask the corresponding bit from
         * compare.
         */
        uint16_t        l2_ovlan_mask;
        /* This value sets VLAN ID value for inner VLAN. */
        uint16_t        l2_ivlan;
        /*
         * This value sets the mask value for the ivlan id.
         * A value of 0 will mask the corresponding bit from
         * compare.
         */
        uint16_t        l2_ivlan_mask;
        uint8_t unused_1[2];
        /*
         * This value sets the match value for the tunnel
         * L2 MAC address.
         * Destination MAC address for RX path.
         * Source MAC address for TX path.
         */
        uint8_t t_l2_addr[6];
        uint8_t unused_2[2];
        /*
         * This value sets the mask value for the tunnel L2
         * address.
         * A value of 0 will mask the corresponding bit from
         * compare.
         */
        uint8_t t_l2_addr_mask[6];
        /* This value sets VLAN ID value for tunnel outer VLAN. */
        uint16_t        t_l2_ovlan;
        /*
         * This value sets the mask value for the tunnel ovlan id.
         * A value of 0 will mask the corresponding bit from
         * compare.
         */
        uint16_t        t_l2_ovlan_mask;
        /* This value sets VLAN ID value for tunnel inner VLAN. */
        uint16_t        t_l2_ivlan;
        /*
         * This value sets the mask value for the tunnel ivlan id.
         * A value of 0 will mask the corresponding bit from
         * compare.
         */
        uint16_t        t_l2_ivlan_mask;
        /* This value identifies the type of source of the packet. */
        uint8_t src_type;
        /* Network port */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT UINT32_C(0x0)
        /* Physical function */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF    UINT32_C(0x1)
        /* Virtual function */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF    UINT32_C(0x2)
        /* Virtual NIC of a function */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC  UINT32_C(0x3)
        /* Embedded processor for CFA management */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG  UINT32_C(0x4)
        /* Embedded processor for OOB management */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE   UINT32_C(0x5)
        /* Embedded processor for RoCE */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO  UINT32_C(0x6)
        /* Embedded processor for network proxy functions */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG  UINT32_C(0x7)
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_LAST \
                HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG
        uint8_t unused_3;
        /*
         * This value is the id of the source.
         * For a network port, it represents port_id.
         * For a physical function, it represents fid.
         * For a virtual function, it represents vf_id.
         * For a vnic, it represents vnic_id.
         * For embedded processors, this id is not valid.
         *
         * Notes:
         * 1. The function ID is implied if it src_id is
         *    not provided for a src_type that is either
         */
        uint32_t        src_id;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Any tunneled traffic */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
        uint8_t unused_4;
        /*
         * If set, this value shall represent the
         * Logical VNIC ID of the destination VNIC for the RX
         * path and network port id of the destination port for
         * the TX path.
         */
        uint16_t        dst_id;
        /*
         * Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint16_t        mirror_vnic_id;
        /*
         * This hint is provided to help in placing
         * the filter in the filter table.
         */
        uint8_t pri_hint;
        /* No preference */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
                UINT32_C(0x0)
        /* Above the given filter */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER \
                UINT32_C(0x1)
        /* Below the given filter */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER \
                UINT32_C(0x2)
        /* As high as possible */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX \
                UINT32_C(0x3)
        /* As low as possible */
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN \
                UINT32_C(0x4)
        #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_LAST \
                HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN
        uint8_t unused_5;
        uint32_t        unused_6;
        /*
         * This is the ID of the filter that goes along with
         * the pri_hint.
         *
         * This field is valid only for the following values.
         * 1 - Above the given filter
         * 2 - Below the given filter
         */
        uint64_t        l2_filter_id_hint;
} __attribute__((packed));

/* hwrm_cfa_l2_filter_alloc_output (size:192b/24B) */
struct hwrm_cfa_l2_filter_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This value identifies a set of CFA data structures used for an L2
         * context.
         */
        uint64_t        l2_filter_id;
        /*
         * This is the ID of the flow associated with this
         * filter.
         * This value shall be used to match and associate the
         * flow identifier returned in completion records.
         * A value of 0xFFFFFFFF shall indicate no flow id.
         */
        uint32_t        flow_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_cfa_l2_filter_free *
 ***************************/


/* hwrm_cfa_l2_filter_free_input (size:192b/24B) */
struct hwrm_cfa_l2_filter_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This value identifies a set of CFA data structures used for an L2
         * context.
         */
        uint64_t        l2_filter_id;
} __attribute__((packed));

/* hwrm_cfa_l2_filter_free_output (size:128b/16B) */
struct hwrm_cfa_l2_filter_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_cfa_l2_filter_cfg *
 **************************/


/* hwrm_cfa_l2_filter_cfg_input (size:320b/40B) */
struct hwrm_cfa_l2_filter_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_TX    UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX    UINT32_C(0x1)
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX
        /*
         * Setting of this flag indicates drop action. If this flag is not set,
         * then it should be considered accept action.
         */
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_DROP     UINT32_C(0x2)
        uint32_t        enables;
        /*
         * This bit must be '1' for the dst_id field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_DST_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the new_mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
                UINT32_C(0x2)
        /*
         * This value identifies a set of CFA data structures used for an L2
         * context.
         */
        uint64_t        l2_filter_id;
        /*
         * If set, this value shall represent the
         * Logical VNIC ID of the destination VNIC for the RX
         * path and network port id of the destination port for
         * the TX path.
         */
        uint32_t        dst_id;
        /*
         * New Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint32_t        new_mirror_vnic_id;
} __attribute__((packed));

/* hwrm_cfa_l2_filter_cfg_output (size:128b/16B) */
struct hwrm_cfa_l2_filter_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_cfa_l2_set_rx_mask *
 ***************************/


/* hwrm_cfa_l2_set_rx_mask_input (size:448b/56B) */
struct hwrm_cfa_l2_set_rx_mask_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* VNIC ID */
        uint32_t        vnic_id;
        uint32_t        mask;
        /*
         * When this bit is '1', the function is requested to accept
         * multi-cast packets specified by the multicast addr table.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST \
                UINT32_C(0x2)
        /*
         * When this bit is '1', the function is requested to accept
         * all multi-cast packets.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST \
                UINT32_C(0x4)
        /*
         * When this bit is '1', the function is requested to accept
         * broadcast packets.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST \
                UINT32_C(0x8)
        /*
         * When this bit is '1', the function is requested to be
         * put in the promiscuous mode.
         *
         * The HWRM should accept any function to set up
         * promiscuous mode.
         *
         * The HWRM shall follow the semantics below for the
         * promiscuous mode support.
         * # When partitioning is not enabled on a port
         * (i.e. single PF on the port), then the PF shall
         * be allowed to be in the promiscuous mode. When the
         * PF is in the promiscuous mode, then it shall
         * receive all host bound traffic on that port.
         * # When partitioning is enabled on a port
         * (i.e. multiple PFs per port) and a PF on that
         * port is in the promiscuous mode, then the PF
         * receives all traffic within that partition as
         * identified by a unique identifier for the
         * PF (e.g. S-Tag). If a unique outer VLAN
         * for the PF is specified, then the setting of
         * promiscuous mode on that PF shall result in the
         * PF receiving all host bound traffic with matching
         * outer VLAN.
         * # A VF shall can be set in the promiscuous mode.
         * In the promiscuous mode, the VF does not receive any
         * traffic unless a unique outer VLAN for the
         * VF is specified. If a unique outer VLAN
         * for the VF is specified, then the setting of
         * promiscuous mode on that VF shall result in the
         * VF receiving all host bound traffic with the
         * matching outer VLAN.
         * # The HWRM shall allow the setting of promiscuous
         * mode on a function independently from the
         * promiscuous mode settings on other functions.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS \
                UINT32_C(0x10)
        /*
         * If this flag is set, the corresponding RX
         * filters shall be set up to cover multicast/broadcast
         * filters for the outermost Layer 2 destination MAC
         * address field.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST \
                UINT32_C(0x20)
        /*
         * If this flag is set, the corresponding RX
         * filters shall be set up to cover multicast/broadcast
         * filters for the VLAN-tagged packets that match the
         * TPID and VID fields of VLAN tags in the VLAN tag
         * table specified in this command.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLANONLY \
                UINT32_C(0x40)
        /*
         * If this flag is set, the corresponding RX
         * filters shall be set up to cover multicast/broadcast
         * filters for non-VLAN tagged packets and VLAN-tagged
         * packets that match the TPID and VID fields of VLAN
         * tags in the VLAN tag table specified in this command.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLAN_NONVLAN \
                UINT32_C(0x80)
        /*
         * If this flag is set, the corresponding RX
         * filters shall be set up to cover multicast/broadcast
         * filters for non-VLAN tagged packets and VLAN-tagged
         * packets matching any VLAN tag.
         *
         * If this flag is set, then the HWRM shall ignore
         * VLAN tags specified in vlan_tag_tbl.
         *
         * If none of vlanonly, vlan_nonvlan, and anyvlan_nonvlan
         * flags is set, then the HWRM shall ignore
         * VLAN tags specified in vlan_tag_tbl.
         *
         * The HWRM client shall set at most one flag out of
         * vlanonly, vlan_nonvlan, and anyvlan_nonvlan.
         */
        #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ANYVLAN_NONVLAN \
                UINT32_C(0x100)
        /* This is the address for mcast address tbl. */
        uint64_t        mc_tbl_addr;
        /*
         * This value indicates how many entries in mc_tbl are valid.
         * Each entry is 6 bytes.
         */
        uint32_t        num_mc_entries;
        uint8_t unused_0[4];
        /*
         * This is the address for VLAN tag table.
         * Each VLAN entry in the table is 4 bytes of a VLAN tag
         * including TPID, PCP, DEI, and VID fields in network byte
         * order.
         */
        uint64_t        vlan_tag_tbl_addr;
        /*
         * This value indicates how many entries in vlan_tag_tbl are
         * valid. Each entry is 4 bytes.
         */
        uint32_t        num_vlan_tags;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_cfa_l2_set_rx_mask_output (size:128b/16B) */
struct hwrm_cfa_l2_set_rx_mask_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_cfa_l2_set_rx_mask_cmd_err (size:64b/8B) */
struct hwrm_cfa_l2_set_rx_mask_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_UNKNOWN \
                UINT32_C(0x0)
        /* Unable to complete operation due to conflict with Ntuple Filter */
        #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_NTUPLE_FILTER_CONFLICT_ERR \
                UINT32_C(0x1)
        #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_LAST \
                HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_NTUPLE_FILTER_CONFLICT_ERR
        uint8_t unused_0[7];
} __attribute__((packed));

/*******************************
 * hwrm_cfa_vlan_antispoof_cfg *
 *******************************/


/* hwrm_cfa_vlan_antispoof_cfg_input (size:256b/32B) */
struct hwrm_cfa_vlan_antispoof_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being configured.
         * Only valid for a VF FID configured by the PF.
         */
        uint16_t        fid;
        uint8_t unused_0[2];
        /* Number of VLAN entries in the vlan_tag_mask_tbl. */
        uint32_t        num_vlan_entries;
        /*
         * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN
         * antispoof table. Each table entry contains the 16-bit TPID
         * (0x8100 or 0x88a8 only), 16-bit VLAN ID, and a 16-bit mask,
         * all in network order to match hwrm_cfa_l2_set_rx_mask.
         * For an individual VLAN entry, the mask value should be 0xfff
         * for the 12-bit VLAN ID.
         */
        uint64_t        vlan_tag_mask_tbl_addr;
} __attribute__((packed));

/* hwrm_cfa_vlan_antispoof_cfg_output (size:128b/16B) */
struct hwrm_cfa_vlan_antispoof_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************************
 * hwrm_cfa_vlan_antispoof_qcfg *
 ********************************/


/* hwrm_cfa_vlan_antispoof_qcfg_input (size:256b/32B) */
struct hwrm_cfa_vlan_antispoof_qcfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Function ID of the function that is being queried.
         * Only valid for a VF FID queried by the PF.
         */
        uint16_t        fid;
        uint8_t unused_0[2];
        /*
         * Maximum number of VLAN entries the firmware is allowed to DMA
         * to vlan_tag_mask_tbl.
         */
        uint32_t        max_vlan_entries;
        /*
         * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN
         * antispoof table to which firmware will DMA to. Each table
         * entry will contain the 16-bit TPID (0x8100 or 0x88a8 only),
         * 16-bit VLAN ID, and a 16-bit mask, all in network order to
         * match hwrm_cfa_l2_set_rx_mask. For an individual VLAN entry,
         * the mask value should be 0xfff for the 12-bit VLAN ID.
         */
        uint64_t        vlan_tag_mask_tbl_addr;
} __attribute__((packed));

/* hwrm_cfa_vlan_antispoof_qcfg_output (size:128b/16B) */
struct hwrm_cfa_vlan_antispoof_qcfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Number of valid entries DMAd by firmware to vlan_tag_mask_tbl. */
        uint32_t        num_vlan_entries;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************************
 * hwrm_cfa_tunnel_filter_alloc *
 ********************************/


/* hwrm_cfa_tunnel_filter_alloc_input (size:704b/88B) */
struct hwrm_cfa_tunnel_filter_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* Setting of this flag indicates the applicability to the loopback path. */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
                UINT32_C(0x1)
        uint32_t        enables;
        /*
         * This bit must be '1' for the l2_filter_id field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the l2_addr field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the l2_ivlan field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the l3_addr field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the l3_addr_type field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR_TYPE \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the t_l3_addr_type field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR_TYPE \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the t_l3_addr field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the tunnel_type field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the vni field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_VNI \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the dst_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_DST_VNIC_ID \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
                UINT32_C(0x400)
        /*
         * This value identifies a set of CFA data structures used for an L2
         * context.
         */
        uint64_t        l2_filter_id;
        /*
         * This value sets the match value for the inner L2
         * MAC address.
         * Destination MAC address for RX path.
         * Source MAC address for TX path.
         */
        uint8_t l2_addr[6];
        /*
         * This value sets VLAN ID value for inner VLAN.
         * Only 12-bits of VLAN ID are used in setting the filter.
         */
        uint16_t        l2_ivlan;
        /*
         * The value of inner destination IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        l3_addr[4];
        /*
         * The value of tunnel destination IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        t_l3_addr[4];
        /*
         * This value indicates the type of inner IP address.
         * 4 - IPv4
         * 6 - IPv6
         * All others are invalid.
         */
        uint8_t l3_addr_type;
        /*
         * This value indicates the type of tunnel IP address.
         * 4 - IPv4
         * 6 - IPv6
         * All others are invalid.
         */
        uint8_t t_l3_addr_type;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Any tunneled traffic */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
        /*
         * tunnel_flags allows the user to indicate the tunnel tag detection
         * for the tunnel type specified in tunnel_type.
         */
        uint8_t tunnel_flags;
        /*
         * If the tunnel_type is geneve, then this bit indicates if we
         * need to match the geneve OAM packet.
         * If the tunnel_type is nvgre or gre, then this bit indicates if
         * we need to detect checksum present bit in geneve header.
         * If the tunnel_type is mpls, then this bit indicates if we need
         * to match mpls packet with explicit IPV4/IPV6 null header.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_OAM_CHECKSUM_EXPLHDR \
                UINT32_C(0x1)
        /*
         * If the tunnel_type is geneve, then this bit indicates if we
         * need to detect the critical option bit set in the oam packet.
         * If the tunnel_type is nvgre or gre, then this bit indicates
         * if we need to match nvgre packets with key present bit set in
         * gre header.
         * If the tunnel_type is mpls, then this bit indicates if we
         * need to match mpls packet with S bit from inner/second label.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_CRITICAL_OPT_S1 \
                UINT32_C(0x2)
        /*
         * If the tunnel_type is geneve, then this bit indicates if we
         * need to match geneve packet with extended header bit set in
         * geneve header.
         * If the tunnel_type is nvgre or gre, then this bit indicates
         * if we need to match nvgre packets with sequence number
         * present bit set in gre header.
         * If the tunnel_type is mpls, then this bit indicates if we
         * need to match mpls packet with S bit from out/first label.
         */
        #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_EXTHDR_SEQNUM_S0 \
                UINT32_C(0x4)
        /*
         * Virtual Network Identifier (VNI). Only valid with
         * tunnel_types VXLAN, NVGRE, and Geneve.
         * Only lower 24-bits of VNI field are used
         * in setting up the filter.
         */
        uint32_t        vni;
        /* Logical VNIC ID of the destination VNIC. */
        uint32_t        dst_vnic_id;
        /*
         * Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint32_t        mirror_vnic_id;
} __attribute__((packed));

/* hwrm_cfa_tunnel_filter_alloc_output (size:192b/24B) */
struct hwrm_cfa_tunnel_filter_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value is an opaque id into CFA data structures. */
        uint64_t        tunnel_filter_id;
        /*
         * This is the ID of the flow associated with this
         * filter.
         * This value shall be used to match and associate the
         * flow identifier returned in completion records.
         * A value of 0xFFFFFFFF shall indicate no flow id.
         */
        uint32_t        flow_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************************
 * hwrm_cfa_tunnel_filter_free *
 *******************************/


/* hwrm_cfa_tunnel_filter_free_input (size:192b/24B) */
struct hwrm_cfa_tunnel_filter_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This value is an opaque id into CFA data structures. */
        uint64_t        tunnel_filter_id;
} __attribute__((packed));

/* hwrm_cfa_tunnel_filter_free_output (size:128b/16B) */
struct hwrm_cfa_tunnel_filter_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************************
 * hwrm_cfa_redirect_tunnel_type_alloc *
 ***************************************/


/* hwrm_cfa_redirect_tunnel_type_alloc_input (size:192b/24B) */
struct hwrm_cfa_redirect_tunnel_type_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* The destination function id, to whom the traffic is redirected. */
        uint16_t        dest_fid;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
                UINT32_C(0xa)
        /* Any tunneled traffic */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
        /* Tunnel alloc flags. */
        uint8_t flags;
        /* Setting of this flag indicates modify existing redirect tunnel to new destination function ID. */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_FLAGS_MODIFY_DST \
                UINT32_C(0x1)
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_cfa_redirect_tunnel_type_alloc_output (size:128b/16B) */
struct hwrm_cfa_redirect_tunnel_type_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************************
 * hwrm_cfa_redirect_tunnel_type_free *
 **************************************/


/* hwrm_cfa_redirect_tunnel_type_free_input (size:192b/24B) */
struct hwrm_cfa_redirect_tunnel_type_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* The destination function id, to whom the traffic is redirected. */
        uint16_t        dest_fid;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE_V1 \
                UINT32_C(0xa)
        /* Any tunneled traffic */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL
        uint8_t unused_0[5];
} __attribute__((packed));

/* hwrm_cfa_redirect_tunnel_type_free_output (size:128b/16B) */
struct hwrm_cfa_redirect_tunnel_type_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************************
 * hwrm_cfa_redirect_tunnel_type_info *
 **************************************/


/* hwrm_cfa_redirect_tunnel_type_info_input (size:192b/24B) */
struct hwrm_cfa_redirect_tunnel_type_info_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* The source function id. */
        uint16_t        src_fid;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPGRE_V1 \
                UINT32_C(0xa)
        /* Any tunneled traffic */
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_ANYTUNNEL
        uint8_t unused_0[5];
} __attribute__((packed));

/* hwrm_cfa_redirect_tunnel_type_info_output (size:128b/16B) */
struct hwrm_cfa_redirect_tunnel_type_info_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The destination function id, to whom the traffic is redirected. */
        uint16_t        dest_fid;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_vxlan_ipv4_hdr (size:128b/16B) */
struct hwrm_vxlan_ipv4_hdr {
        /* IPv4 version and header length. */
        uint8_t ver_hlen;
        /* IPv4 header length */
        #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_MASK UINT32_C(0xf)
        #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_SFT 0
        /* Version */
        #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_MASK      UINT32_C(0xf0)
        #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_SFT       4
        /* IPv4 type of service. */
        uint8_t tos;
        /* IPv4 identification. */
        uint16_t        ip_id;
        /* IPv4 flags and offset. */
        uint16_t        flags_frag_offset;
        /* IPv4 TTL. */
        uint8_t ttl;
        /* IPv4 protocol. */
        uint8_t protocol;
        /* IPv4 source address. */
        uint32_t        src_ip_addr;
        /* IPv4 destination address. */
        uint32_t        dest_ip_addr;
} __attribute__((packed));

/* hwrm_vxlan_ipv6_hdr (size:320b/40B) */
struct hwrm_vxlan_ipv6_hdr {
        /* IPv6 version, traffic class and flow label. */
        uint32_t        ver_tc_flow_label;
        /* IPv6 version shift */
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_SFT \
                UINT32_C(0x1c)
        /* IPv6 version mask */
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_MASK \
                UINT32_C(0xf0000000)
        /* IPv6 TC shift */
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_SFT \
                UINT32_C(0x14)
        /* IPv6 TC mask */
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_MASK \
                UINT32_C(0xff00000)
        /* IPv6 flow label shift */
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_SFT \
                UINT32_C(0x0)
        /* IPv6 flow label mask */
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK \
                UINT32_C(0xfffff)
        #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_LAST \
                HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK
        /* IPv6 payload length. */
        uint16_t        payload_len;
        /* IPv6 next header. */
        uint8_t next_hdr;
        /* IPv6 TTL. */
        uint8_t ttl;
        /* IPv6 source address. */
        uint32_t        src_ip_addr[4];
        /* IPv6 destination address. */
        uint32_t        dest_ip_addr[4];
} __attribute__((packed));

/* hwrm_cfa_encap_data_vxlan (size:576b/72B) */
struct hwrm_cfa_encap_data_vxlan {
        /* Source MAC address. */
        uint8_t src_mac_addr[6];
        /* reserved. */
        uint16_t        unused_0;
        /* Destination MAC address. */
        uint8_t dst_mac_addr[6];
        /* Number of VLAN tags. */
        uint8_t num_vlan_tags;
        /* reserved. */
        uint8_t unused_1;
        /* Outer VLAN TPID. */
        uint16_t        ovlan_tpid;
        /* Outer VLAN TCI. */
        uint16_t        ovlan_tci;
        /* Inner VLAN TPID. */
        uint16_t        ivlan_tpid;
        /* Inner VLAN TCI. */
        uint16_t        ivlan_tci;
        /* L3 header fields. */
        uint32_t        l3[10];
        /* IP version mask. */
        #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_MASK UINT32_C(0xf)
        /* IP version 4. */
        #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV4 UINT32_C(0x4)
        /* IP version 6. */
        #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6 UINT32_C(0x6)
        #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_LAST \
                HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6
        /* UDP source port. */
        uint16_t        src_port;
        /* UDP destination port. */
        uint16_t        dst_port;
        /* VXLAN Network Identifier. */
        uint32_t        vni;
} __attribute__((packed));

/*******************************
 * hwrm_cfa_encap_record_alloc *
 *******************************/


/* hwrm_cfa_encap_record_alloc_input (size:832b/104B) */
struct hwrm_cfa_encap_record_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* Setting of this flag indicates the applicability to the loopback path. */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_FLAGS_LOOPBACK \
                UINT32_C(0x1)
        /* Encapsulation Type. */
        uint8_t encap_type;
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) after inside Ethernet payload */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_MPLS \
                UINT32_C(0x6)
        /* VLAN */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VLAN \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPGRE \
                UINT32_C(0x8)
        #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_LAST \
                HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPGRE
        uint8_t unused_0[3];
        /* This value is encap data used for the given encap type. */
        uint32_t        encap_data[20];
} __attribute__((packed));

/* hwrm_cfa_encap_record_alloc_output (size:128b/16B) */
struct hwrm_cfa_encap_record_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value is an opaque id into CFA data structures. */
        uint32_t        encap_record_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************************
 * hwrm_cfa_encap_record_free *
 ******************************/


/* hwrm_cfa_encap_record_free_input (size:192b/24B) */
struct hwrm_cfa_encap_record_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This value is an opaque id into CFA data structures. */
        uint32_t        encap_record_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_cfa_encap_record_free_output (size:128b/16B) */
struct hwrm_cfa_encap_record_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************************
 * hwrm_cfa_ntuple_filter_alloc *
 ********************************/


/* hwrm_cfa_ntuple_filter_alloc_input (size:1024b/128B) */
struct hwrm_cfa_ntuple_filter_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* Setting of this flag indicates the applicability to the loopback path. */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
                UINT32_C(0x1)
        /*
         * Setting of this flag indicates drop action. If this flag is not set,
         * then it should be considered accept action.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DROP \
                UINT32_C(0x2)
        /*
         * Setting of this flag indicates that a meter is expected to be attached
         * to this flow. This hint can be used when choosing the action record
         * format required for the flow.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_METER \
                UINT32_C(0x4)
        uint32_t        enables;
        /*
         * This bit must be '1' for the l2_filter_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the ethertype field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the tunnel_type field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the src_macaddr field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the ipaddr_type field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the src_ipaddr field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the src_ipaddr_mask field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR_MASK \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the dst_ipaddr field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the dst_ipaddr_mask field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR_MASK \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the ip_protocol field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the src_port field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the src_port_mask field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT_MASK \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the dst_port field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the dst_port_mask field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT_MASK \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the pri_hint field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_PRI_HINT \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the ntuple_filter_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_NTUPLE_FILTER_ID \
                UINT32_C(0x8000)
        /*
         * This bit must be '1' for the dst_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
                UINT32_C(0x10000)
        /*
         * This bit must be '1' for the mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
                UINT32_C(0x20000)
        /*
         * This bit must be '1' for the dst_macaddr field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR \
                UINT32_C(0x40000)
        /*
         * This value identifies a set of CFA data structures used for an L2
         * context.
         */
        uint64_t        l2_filter_id;
        /*
         * This value indicates the source MAC address in
         * the Ethernet header.
         */
        uint8_t src_macaddr[6];
        /* This value indicates the ethertype in the Ethernet header. */
        uint16_t        ethertype;
        /*
         * This value indicates the type of IP address.
         * 4 - IPv4
         * 6 - IPv6
         * All others are invalid.
         */
        uint8_t ip_addr_type;
        /* invalid */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN \
                UINT32_C(0x0)
        /* IPv4 */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 \
                UINT32_C(0x4)
        /* IPv6 */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 \
                UINT32_C(0x6)
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_LAST \
                HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6
        /*
         * The value of protocol filed in IP header.
         * Applies to UDP and TCP traffic.
         * 6 - TCP
         * 17 - UDP
         */
        uint8_t ip_protocol;
        /* invalid */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN \
                UINT32_C(0x0)
        /* TCP */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP \
                UINT32_C(0x6)
        /* UDP */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP \
                UINT32_C(0x11)
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_LAST \
                HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP
        /*
         * If set, this value shall represent the
         * Logical VNIC ID of the destination VNIC for the RX
         * path and network port id of the destination port for
         * the TX path.
         */
        uint16_t        dst_id;
        /*
         * Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint16_t        mirror_vnic_id;
        /*
         * This value indicates the tunnel type for this filter.
         * If this field is not specified, then the filter shall
         * apply to both non-tunneled and tunneled packets.
         * If this field conflicts with the tunnel_type specified
         * in the l2_filter_id, then the HWRM shall return an
         * error for this command.
         */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Any tunneled traffic */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
        /*
         * This hint is provided to help in placing
         * the filter in the filter table.
         */
        uint8_t pri_hint;
        /* No preference */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
                UINT32_C(0x0)
        /* Above the given filter */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE \
                UINT32_C(0x1)
        /* Below the given filter */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_BELOW \
                UINT32_C(0x2)
        /* As high as possible */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_HIGHEST \
                UINT32_C(0x3)
        /* As low as possible */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST \
                UINT32_C(0x4)
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LAST \
                HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST
        /*
         * The value of source IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        src_ipaddr[4];
        /*
         * The value of source IP address mask to be used in
         * filtering.
         * For IPv4, first four bytes represent the IP address mask.
         */
        uint32_t        src_ipaddr_mask[4];
        /*
         * The value of destination IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        dst_ipaddr[4];
        /*
         * The value of destination IP address mask to be used in
         * filtering.
         * For IPv4, first four bytes represent the IP address mask.
         */
        uint32_t        dst_ipaddr_mask[4];
        /*
         * The value of source port to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        src_port;
        /*
         * The value of source port mask to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        src_port_mask;
        /*
         * The value of destination port to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        dst_port;
        /*
         * The value of destination port mask to be used in
         * filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        dst_port_mask;
        /*
         * This is the ID of the filter that goes along with
         * the pri_hint.
         */
        uint64_t        ntuple_filter_id_hint;
} __attribute__((packed));

/* hwrm_cfa_ntuple_filter_alloc_output (size:192b/24B) */
struct hwrm_cfa_ntuple_filter_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value is an opaque id into CFA data structures. */
        uint64_t        ntuple_filter_id;
        /*
         * This is the ID of the flow associated with this
         * filter.
         * This value shall be used to match and associate the
         * flow identifier returned in completion records.
         * A value of 0xFFFFFFFF shall indicate no flow id.
         */
        uint32_t        flow_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_cfa_ntuple_filter_alloc_cmd_err (size:64b/8B) */
struct hwrm_cfa_ntuple_filter_alloc_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_UNKNOWN \
                UINT32_C(0x0)
        /* Unable to complete operation due to conflict with Rx Mask VLAN */
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_RX_MASK_VLAN_CONFLICT_ERR \
                UINT32_C(0x1)
        #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_LAST \
                HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_RX_MASK_VLAN_CONFLICT_ERR
        uint8_t unused_0[7];
} __attribute__((packed));

/*******************************
 * hwrm_cfa_ntuple_filter_free *
 *******************************/


/* hwrm_cfa_ntuple_filter_free_input (size:192b/24B) */
struct hwrm_cfa_ntuple_filter_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This value is an opaque id into CFA data structures. */
        uint64_t        ntuple_filter_id;
} __attribute__((packed));

/* hwrm_cfa_ntuple_filter_free_output (size:128b/16B) */
struct hwrm_cfa_ntuple_filter_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************************
 * hwrm_cfa_ntuple_filter_cfg *
 ******************************/


/* hwrm_cfa_ntuple_filter_cfg_input (size:384b/48B) */
struct hwrm_cfa_ntuple_filter_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the new_dst_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_DST_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the new_mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the new_meter_instance_id field to be
         * configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
                UINT32_C(0x4)
        uint8_t unused_0[4];
        /* This value is an opaque id into CFA data structures. */
        uint64_t        ntuple_filter_id;
        /*
         * If set, this value shall represent the new
         * Logical VNIC ID of the destination VNIC for the RX
         * path and new network port id of the destination port for
         * the TX path.
         */
        uint32_t        new_dst_id;
        /*
         * New Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint32_t        new_mirror_vnic_id;
        /*
         * New meter to attach to the flow. Specifying the
         * invalid instance ID is used to remove any existing
         * meter from the flow.
         */
        uint16_t        new_meter_instance_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * instance is not configured.
         */
        #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_LAST \
                HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID
        uint8_t unused_1[6];
} __attribute__((packed));

/* hwrm_cfa_ntuple_filter_cfg_output (size:128b/16B) */
struct hwrm_cfa_ntuple_filter_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_cfa_em_flow_alloc *
 **************************/


/* hwrm_cfa_em_flow_alloc_input (size:896b/112B) */
struct hwrm_cfa_em_flow_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH         UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_TX        UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX        UINT32_C(0x1)
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX
        /*
         * Setting of this flag indicates enabling of a byte counter for a given
         * flow.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_BYTE_CTR     UINT32_C(0x2)
        /*
         * Setting of this flag indicates enabling of a packet counter for a given
         * flow.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PKT_CTR      UINT32_C(0x4)
        /* Setting of this flag indicates de-capsulation action for the given flow. */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DECAP        UINT32_C(0x8)
        /* Setting of this flag indicates encapsulation action for the given flow. */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_ENCAP        UINT32_C(0x10)
        /*
         * Setting of this flag indicates drop action. If this flag is not set,
         * then it should be considered accept action.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DROP         UINT32_C(0x20)
        /*
         * Setting of this flag indicates that a meter is expected to be attached
         * to this flow. This hint can be used when choosing the action record
         * format required for the flow.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_METER        UINT32_C(0x40)
        uint32_t        enables;
        /*
         * This bit must be '1' for the l2_filter_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the tunnel_type field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the tunnel_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_ID \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the src_macaddr field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_MACADDR \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the dst_macaddr field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_MACADDR \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the ovlan_vid field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_OVLAN_VID \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the ivlan_vid field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IVLAN_VID \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the ethertype field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ETHERTYPE \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the src_ipaddr field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_IPADDR \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the dst_ipaddr field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_IPADDR \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the ipaddr_type field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the ip_protocol field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the src_port field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_PORT \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the dst_port field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_PORT \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the dst_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_ID \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
                UINT32_C(0x8000)
        /*
         * This bit must be '1' for the encap_record_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ENCAP_RECORD_ID \
                UINT32_C(0x10000)
        /*
         * This bit must be '1' for the meter_instance_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_METER_INSTANCE_ID \
                UINT32_C(0x20000)
        /*
         * This value identifies a set of CFA data structures used for an L2
         * context.
         */
        uint64_t        l2_filter_id;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Any tunneled traffic */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
        uint8_t unused_0[3];
        /*
         * Tunnel identifier.
         * Virtual Network Identifier (VNI). Only valid with
         * tunnel_types VXLAN, NVGRE, and Geneve.
         * Only lower 24-bits of VNI field are used
         * in setting up the filter.
         */
        uint32_t        tunnel_id;
        /*
         * This value indicates the source MAC address in
         * the Ethernet header.
         */
        uint8_t src_macaddr[6];
        /* The meter instance to attach to the flow. */
        uint16_t        meter_instance_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * instance is not configured.
         */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_LAST \
                HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID
        /*
         * This value indicates the destination MAC address in
         * the Ethernet header.
         */
        uint8_t dst_macaddr[6];
        /*
         * This value indicates the VLAN ID of the outer VLAN tag
         * in the Ethernet header.
         */
        uint16_t        ovlan_vid;
        /*
         * This value indicates the VLAN ID of the inner VLAN tag
         * in the Ethernet header.
         */
        uint16_t        ivlan_vid;
        /* This value indicates the ethertype in the Ethernet header. */
        uint16_t        ethertype;
        /*
         * This value indicates the type of IP address.
         * 4 - IPv4
         * 6 - IPv6
         * All others are invalid.
         */
        uint8_t ip_addr_type;
        /* invalid */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN UINT32_C(0x0)
        /* IPv4 */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV4    UINT32_C(0x4)
        /* IPv6 */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6    UINT32_C(0x6)
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_LAST \
                HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6
        /*
         * The value of protocol filed in IP header.
         * Applies to UDP and TCP traffic.
         * 6 - TCP
         * 17 - UDP
         */
        uint8_t ip_protocol;
        /* invalid */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN UINT32_C(0x0)
        /* TCP */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_TCP     UINT32_C(0x6)
        /* UDP */
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP     UINT32_C(0x11)
        #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_LAST \
                HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP
        uint8_t unused_1[2];
        /*
         * The value of source IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        src_ipaddr[4];
        /*
         * big_endian = True
         *     The value of destination IP address to be used in filtering.
         *     For IPv4, first four bytes represent the IP address.
         */
        uint32_t        dst_ipaddr[4];
        /*
         * The value of source port to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        src_port;
        /*
         * The value of destination port to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        dst_port;
        /*
         * If set, this value shall represent the
         * Logical VNIC ID of the destination VNIC for the RX
         * path and network port id of the destination port for
         * the TX path.
         */
        uint16_t        dst_id;
        /*
         * Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint16_t        mirror_vnic_id;
        /* Logical ID of the encapsulation record. */
        uint32_t        encap_record_id;
        uint8_t unused_2[4];
} __attribute__((packed));

/* hwrm_cfa_em_flow_alloc_output (size:192b/24B) */
struct hwrm_cfa_em_flow_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value is an opaque id into CFA data structures. */
        uint64_t        em_filter_id;
        /*
         * This is the ID of the flow associated with this
         * filter.
         * This value shall be used to match and associate the
         * flow identifier returned in completion records.
         * A value of 0xFFFFFFFF shall indicate no flow id.
         */
        uint32_t        flow_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_cfa_em_flow_free *
 *************************/


/* hwrm_cfa_em_flow_free_input (size:192b/24B) */
struct hwrm_cfa_em_flow_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This value is an opaque id into CFA data structures. */
        uint64_t        em_filter_id;
} __attribute__((packed));

/* hwrm_cfa_em_flow_free_output (size:128b/16B) */
struct hwrm_cfa_em_flow_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/************************
 * hwrm_cfa_em_flow_cfg *
 ************************/


/* hwrm_cfa_em_flow_cfg_input (size:384b/48B) */
struct hwrm_cfa_em_flow_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the new_dst_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_DST_ID \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the new_mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the new_meter_instance_id field to be
         * configured.
         */
        #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
                UINT32_C(0x4)
        uint8_t unused_0[4];
        /* This value is an opaque id into CFA data structures. */
        uint64_t        em_filter_id;
        /*
         * If set, this value shall represent the new
         * Logical VNIC ID of the destination VNIC for the RX
         * path and network port id of the destination port for
         * the TX path.
         */
        uint32_t        new_dst_id;
        /*
         * New Logical VNIC ID of the VNIC where traffic is
         * mirrored.
         */
        uint32_t        new_mirror_vnic_id;
        /*
         * New meter to attach to the flow. Specifying the
         * invalid instance ID is used to remove any existing
         * meter from the flow.
         */
        uint16_t        new_meter_instance_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * instance is not configured.
         */
        #define HWRM_CFA_EM_FLOW_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_EM_FLOW_CFG_INPUT_NEW_METER_INSTANCE_ID_LAST \
                HWRM_CFA_EM_FLOW_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID
        uint8_t unused_1[6];
} __attribute__((packed));

/* hwrm_cfa_em_flow_cfg_output (size:128b/16B) */
struct hwrm_cfa_em_flow_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************************
 * hwrm_cfa_meter_profile_alloc *
 ********************************/


/* hwrm_cfa_meter_profile_alloc_input (size:320b/40B) */
struct hwrm_cfa_meter_profile_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint8_t flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_TX \
                UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_RX \
                UINT32_C(0x1)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_RX
        /* The meter algorithm type. */
        uint8_t meter_type;
        /* RFC 2697 (srTCM) */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC2697 \
                UINT32_C(0x0)
        /* RFC 2698 (trTCM) */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC2698 \
                UINT32_C(0x1)
        /* RFC 4115 (trTCM) */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC4115 \
                UINT32_C(0x2)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC4115
        /*
         * This field is reserved for the future use.
         * It shall be set to 0.
         */
        uint16_t        reserved1;
        /*
         * This field is reserved for the future use.
         * It shall be set to 0.
         */
        uint32_t        reserved2;
        /* A meter rate specified in bytes-per-second. */
        uint32_t        commit_rate;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID
        /* A meter burst size specified in bytes. */
        uint32_t        commit_burst;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID
        /* A meter rate specified in bytes-per-second. */
        uint32_t        excess_peak_rate;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID
        /* A meter burst size specified in bytes. */
        uint32_t        excess_peak_burst;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID
} __attribute__((packed));

/* hwrm_cfa_meter_profile_alloc_output (size:128b/16B) */
struct hwrm_cfa_meter_profile_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value identifies a meter profile in CFA. */
        uint16_t        meter_profile_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * profile is not configured.
         */
        #define HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_LAST \
                HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_INVALID
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************************
 * hwrm_cfa_meter_profile_free *
 *******************************/


/* hwrm_cfa_meter_profile_free_input (size:192b/24B) */
struct hwrm_cfa_meter_profile_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint8_t flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_TX \
                UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_RX \
                UINT32_C(0x1)
        #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_RX
        uint8_t unused_0;
        /* This value identifies a meter profile in CFA. */
        uint16_t        meter_profile_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * profile is not configured.
         */
        #define HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_LAST \
                HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_INVALID
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_cfa_meter_profile_free_output (size:128b/16B) */
struct hwrm_cfa_meter_profile_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************************
 * hwrm_cfa_meter_profile_cfg *
 ******************************/


/* hwrm_cfa_meter_profile_cfg_input (size:320b/40B) */
struct hwrm_cfa_meter_profile_cfg_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint8_t flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_TX    UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_RX    UINT32_C(0x1)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_RX
        /* The meter algorithm type. */
        uint8_t meter_type;
        /* RFC 2697 (srTCM) */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC2697 \
                UINT32_C(0x0)
        /* RFC 2698 (trTCM) */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC2698 \
                UINT32_C(0x1)
        /* RFC 4115 (trTCM) */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC4115 \
                UINT32_C(0x2)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC4115
        /* This value identifies a meter profile in CFA. */
        uint16_t        meter_profile_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * profile is not configured.
         */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_INVALID
        /*
         * This field is reserved for the future use.
         * It shall be set to 0.
         */
        uint32_t        reserved;
        /* A meter rate specified in bytes-per-second. */
        uint32_t        commit_rate;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_INVALID
        /* A meter burst size specified in bytes. */
        uint32_t        commit_burst;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID
        /* A meter rate specified in bytes-per-second. */
        uint32_t        excess_peak_rate;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_INVALID
        /* A meter burst size specified in bytes. */
        uint32_t        excess_peak_burst;
        /* The bandwidth value. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_MASK \
                UINT32_C(0xfffffff)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_SFT \
                0
        /* The granularity of the value (bits or bytes). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE \
                UINT32_C(0x10000000)
        /* Value is in bits. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BITS \
                (UINT32_C(0x0) << 28)
        /* Value is in bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES \
                (UINT32_C(0x1) << 28)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES
        /* bw_value_unit is 3 b */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MASK \
                UINT32_C(0xe0000000)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_SFT \
                29
        /* Value is in Mb or MB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MEGA \
                (UINT32_C(0x0) << 29)
        /* Value is in Kb or KB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_KILO \
                (UINT32_C(0x2) << 29)
        /* Value is in bits or bytes. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_BASE \
                (UINT32_C(0x4) << 29)
        /* Value is in Gb or GB (base 10). */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_GIGA \
                (UINT32_C(0x6) << 29)
        /* Value is in 1/100th of a percentage of total bandwidth. */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_PERCENT1_100 \
                (UINT32_C(0x1) << 29)
        /* Invalid unit */
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID \
                (UINT32_C(0x7) << 29)
        #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_LAST \
                HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID
} __attribute__((packed));

/* hwrm_cfa_meter_profile_cfg_output (size:128b/16B) */
struct hwrm_cfa_meter_profile_cfg_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************************
 * hwrm_cfa_meter_instance_alloc *
 *********************************/


/* hwrm_cfa_meter_instance_alloc_input (size:192b/24B) */
struct hwrm_cfa_meter_instance_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint8_t flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH \
                UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_TX \
                UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_RX \
                UINT32_C(0x1)
        #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_RX
        uint8_t unused_0;
        /* This value identifies a meter profile in CFA. */
        uint16_t        meter_profile_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * profile is not configured.
         */
        #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_LAST \
                HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_INVALID
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_cfa_meter_instance_alloc_output (size:128b/16B) */
struct hwrm_cfa_meter_instance_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value identifies a meter instance in CFA. */
        uint16_t        meter_instance_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * instance is not configured.
         */
        #define HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_LAST \
                HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_INVALID
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************************
 * hwrm_cfa_meter_instance_free *
 ********************************/


/* hwrm_cfa_meter_instance_free_input (size:192b/24B) */
struct hwrm_cfa_meter_instance_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint8_t flags;
        /*
         * Enumeration denoting the RX, TX type of the resource.
         * This enumeration is used for resources that are similar for both
         * TX and RX paths of the chip.
         */
        #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH     UINT32_C(0x1)
        /* tx path */
        #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_TX \
                UINT32_C(0x0)
        /* rx path */
        #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_RX \
                UINT32_C(0x1)
        #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_LAST \
                HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_RX
        uint8_t unused_0;
        /* This value identifies a meter instance in CFA. */
        uint16_t        meter_instance_id;
        /*
         * A value of 0xfff is considered invalid and implies the
         * instance is not configured.
         */
        #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_INVALID \
                UINT32_C(0xffff)
        #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_LAST \
                HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_INVALID
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_cfa_meter_instance_free_output (size:128b/16B) */
struct hwrm_cfa_meter_instance_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*******************************
 * hwrm_cfa_decap_filter_alloc *
 *******************************/


/* hwrm_cfa_decap_filter_alloc_input (size:832b/104B) */
struct hwrm_cfa_decap_filter_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* ovs_tunnel is 1 b */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_FLAGS_OVS_TUNNEL \
                UINT32_C(0x1)
        uint32_t        enables;
        /*
         * This bit must be '1' for the tunnel_type field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
                UINT32_C(0x1)
        /*
         * This bit must be '1' for the tunnel_id field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_ID \
                UINT32_C(0x2)
        /*
         * This bit must be '1' for the src_macaddr field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR \
                UINT32_C(0x4)
        /*
         * This bit must be '1' for the dst_macaddr field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR \
                UINT32_C(0x8)
        /*
         * This bit must be '1' for the ovlan_vid field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_OVLAN_VID \
                UINT32_C(0x10)
        /*
         * This bit must be '1' for the ivlan_vid field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IVLAN_VID \
                UINT32_C(0x20)
        /*
         * This bit must be '1' for the t_ovlan_vid field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_T_OVLAN_VID \
                UINT32_C(0x40)
        /*
         * This bit must be '1' for the t_ivlan_vid field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_T_IVLAN_VID \
                UINT32_C(0x80)
        /*
         * This bit must be '1' for the ethertype field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE \
                UINT32_C(0x100)
        /*
         * This bit must be '1' for the src_ipaddr field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR \
                UINT32_C(0x200)
        /*
         * This bit must be '1' for the dst_ipaddr field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR \
                UINT32_C(0x400)
        /*
         * This bit must be '1' for the ipaddr_type field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
                UINT32_C(0x800)
        /*
         * This bit must be '1' for the ip_protocol field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
                UINT32_C(0x1000)
        /*
         * This bit must be '1' for the src_port field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT \
                UINT32_C(0x2000)
        /*
         * This bit must be '1' for the dst_port field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_PORT \
                UINT32_C(0x4000)
        /*
         * This bit must be '1' for the dst_id field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
                UINT32_C(0x8000)
        /*
         * This bit must be '1' for the mirror_vnic_id field to be
         * configured.
         */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
                UINT32_C(0x10000)
        /*
         * Tunnel identifier.
         * Virtual Network Identifier (VNI). Only valid with
         * tunnel_types VXLAN, NVGRE, and Geneve.
         * Only lower 24-bits of VNI field are used
         * in setting up the filter.
         */
        uint32_t        tunnel_id;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Non-tunnel */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
                UINT32_C(0x0)
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
                UINT32_C(0x2)
        /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
                UINT32_C(0x3)
        /* IP in IP */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
                UINT32_C(0x4)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* Multi-Protocol Lable Switching (MPLS) */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
                UINT32_C(0x6)
        /* Stateless Transport Tunnel (STT) */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
                UINT32_C(0x7)
        /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
                UINT32_C(0x8)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Any tunneled traffic */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
                UINT32_C(0xff)
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
        uint8_t unused_0;
        uint16_t        unused_1;
        /*
         * This value indicates the source MAC address in
         * the Ethernet header.
         */
        uint8_t src_macaddr[6];
        uint8_t unused_2[2];
        /*
         * This value indicates the destination MAC address in
         * the Ethernet header.
         */
        uint8_t dst_macaddr[6];
        /*
         * This value indicates the VLAN ID of the outer VLAN tag
         * in the Ethernet header.
         */
        uint16_t        ovlan_vid;
        /*
         * This value indicates the VLAN ID of the inner VLAN tag
         * in the Ethernet header.
         */
        uint16_t        ivlan_vid;
        /*
         * This value indicates the VLAN ID of the outer VLAN tag
         * in the tunnel Ethernet header.
         */
        uint16_t        t_ovlan_vid;
        /*
         * This value indicates the VLAN ID of the inner VLAN tag
         * in the tunnel Ethernet header.
         */
        uint16_t        t_ivlan_vid;
        /* This value indicates the ethertype in the Ethernet header. */
        uint16_t        ethertype;
        /*
         * This value indicates the type of IP address.
         * 4 - IPv4
         * 6 - IPv6
         * All others are invalid.
         */
        uint8_t ip_addr_type;
        /* invalid */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN \
                UINT32_C(0x0)
        /* IPv4 */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 \
                UINT32_C(0x4)
        /* IPv6 */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 \
                UINT32_C(0x6)
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_LAST \
                HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6
        /*
         * The value of protocol filed in IP header.
         * Applies to UDP and TCP traffic.
         * 6 - TCP
         * 17 - UDP
         */
        uint8_t ip_protocol;
        /* invalid */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN \
                UINT32_C(0x0)
        /* TCP */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP \
                UINT32_C(0x6)
        /* UDP */
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP \
                UINT32_C(0x11)
        #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_LAST \
                HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP
        uint16_t        unused_3;
        uint32_t        unused_4;
        /*
         * The value of source IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        src_ipaddr[4];
        /*
         * The value of destination IP address to be used in filtering.
         * For IPv4, first four bytes represent the IP address.
         */
        uint32_t        dst_ipaddr[4];
        /*
         * The value of source port to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        src_port;
        /*
         * The value of destination port to be used in filtering.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        dst_port;
        /*
         * If set, this value shall represent the
         * Logical VNIC ID of the destination VNIC for the RX
         * path.
         */
        uint16_t        dst_id;
        /*
         * If set, this value shall represent the L2 context that matches the L2
         * information of the decap filter.
         */
        uint16_t        l2_ctxt_ref_id;
} __attribute__((packed));

/* hwrm_cfa_decap_filter_alloc_output (size:128b/16B) */
struct hwrm_cfa_decap_filter_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This value is an opaque id into CFA data structures. */
        uint32_t        decap_filter_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************************
 * hwrm_cfa_decap_filter_free *
 ******************************/


/* hwrm_cfa_decap_filter_free_input (size:192b/24B) */
struct hwrm_cfa_decap_filter_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This value is an opaque id into CFA data structures. */
        uint32_t        decap_filter_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_cfa_decap_filter_free_output (size:128b/16B) */
struct hwrm_cfa_decap_filter_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_cfa_flow_alloc *
 ***********************/


/* hwrm_cfa_flow_alloc_input (size:1024b/128B) */
struct hwrm_cfa_flow_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint16_t        flags;
        /* tunnel is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_TUNNEL       UINT32_C(0x1)
        /* num_vlan is 2 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_MASK UINT32_C(0x6)
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_SFT 1
        /* no tags */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_NONE \
                (UINT32_C(0x0) << 1)
        /* 1 tag */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_ONE \
                (UINT32_C(0x1) << 1)
        /* 2 tags */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_TWO \
                (UINT32_C(0x2) << 1)
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_LAST \
                HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_TWO
        /* Enumeration denoting the Flow Type. */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_MASK UINT32_C(0x38)
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_SFT 3
        /* L2 flow */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_L2 \
                (UINT32_C(0x0) << 3)
        /* IPV4 flow */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV4 \
                (UINT32_C(0x1) << 3)
        /* IPV6 flow */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV6 \
                (UINT32_C(0x2) << 3)
        #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_LAST \
                HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV6
        /*
         * Tx Flow: vf fid.
         * Rx Flow: pf fid.
         */
        uint16_t        src_fid;
        /* Tunnel handle valid when tunnel flag is set. */
        uint32_t        tunnel_handle;
        uint16_t        action_flags;
        /*
         * Setting of this flag indicates drop action. If this flag is not set,
         * then it should be considered accept action.
         */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_FWD \
                UINT32_C(0x1)
        /* recycle is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_RECYCLE \
                UINT32_C(0x2)
        /*
         * Setting of this flag indicates drop action. If this flag is not set,
         * then it should be considered accept action.
         */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_DROP \
                UINT32_C(0x4)
        /* meter is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_METER \
                UINT32_C(0x8)
        /* tunnel is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TUNNEL \
                UINT32_C(0x10)
        /* nat_src is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_SRC \
                UINT32_C(0x20)
        /* nat_dest is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_DEST \
                UINT32_C(0x40)
        /* nat_ipv4_address is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_IPV4_ADDRESS \
                UINT32_C(0x80)
        /* l2_header_rewrite is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_L2_HEADER_REWRITE \
                UINT32_C(0x100)
        /* ttl_decrement is 1 b */
        #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TTL_DECREMENT \
                UINT32_C(0x200)
        /*
         * Tx Flow: pf or vf fid.
         * Rx Flow: vf fid.
         */
        uint16_t        dst_fid;
        /* VLAN tpid, valid when push_vlan flag is set. */
        uint16_t        l2_rewrite_vlan_tpid;
        /* VLAN tci, valid when push_vlan flag is set. */
        uint16_t        l2_rewrite_vlan_tci;
        /* Meter id, valid when meter flag is set. */
        uint16_t        act_meter_id;
        /* Flow with the same l2 context tcam key. */
        uint16_t        ref_flow_handle;
        /* This value sets the match value for the ethertype. */
        uint16_t        ethertype;
        /* valid when num tags is 1 or 2. */
        uint16_t        outer_vlan_tci;
        /* This value sets the match value for the Destination MAC address. */
        uint16_t        dmac[3];
        /* valid when num tags is 2. */
        uint16_t        inner_vlan_tci;
        /* This value sets the match value for the Source MAC address. */
        uint16_t        smac[3];
        /* The bit length of destination IP address mask. */
        uint8_t ip_dst_mask_len;
        /* The bit length of source IP address mask. */
        uint8_t ip_src_mask_len;
        /* The value of destination IPv4/IPv6 address. */
        uint32_t        ip_dst[4];
        /* The source IPv4/IPv6 address. */
        uint32_t        ip_src[4];
        /*
         * The value of source port.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        l4_src_port;
        /*
         * The value of source port mask.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        l4_src_port_mask;
        /*
         * The value of destination port.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        l4_dst_port;
        /*
         * The value of destination port mask.
         * Applies to UDP and TCP traffic.
         */
        uint16_t        l4_dst_port_mask;
        /*
         * NAT IPv4/6 address based on address type flag.
         * 0 values are ignored.
         */
        uint32_t        nat_ip_address[4];
        /* L2 header re-write Destination MAC address. */
        uint16_t        l2_rewrite_dmac[3];
        /*
         * The NAT source/destination port based on direction flag.
         * Applies to UDP and TCP traffic.
         * 0 values are ignored.
         */
        uint16_t        nat_port;
        /* L2 header re-write Source MAC address. */
        uint16_t        l2_rewrite_smac[3];
        /* The value of ip protocol. */
        uint8_t ip_proto;
        uint8_t unused_0;
} __attribute__((packed));

/* hwrm_cfa_flow_alloc_output (size:128b/16B) */
struct hwrm_cfa_flow_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Flow record index. */
        uint16_t        flow_handle;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_cfa_flow_free *
 **********************/


/* hwrm_cfa_flow_free_input (size:192b/24B) */
struct hwrm_cfa_flow_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Flow record index. */
        uint16_t        flow_handle;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_cfa_flow_free_output (size:256b/32B) */
struct hwrm_cfa_flow_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* packet is 64 b */
        uint64_t        packet;
        /* byte is 64 b */
        uint64_t        byte;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_cfa_flow_info *
 **********************/


/* hwrm_cfa_flow_info_input (size:192b/24B) */
struct hwrm_cfa_flow_info_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Flow record index. */
        uint16_t        flow_handle;
        /* Max flow handle */
        #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_MAX_MASK \
                UINT32_C(0xfff)
        #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_MAX_SFT     0
        /* CNP flow handle */
        #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_CNP_CNT \
                UINT32_C(0x1000)
        /* Direction rx = 1 */
        #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_DIR_RX \
                UINT32_C(0x8000)
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_cfa_flow_info_output (size:448b/56B) */
struct hwrm_cfa_flow_info_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* flags is 8 b */
        uint8_t flags;
        /* profile is 8 b */
        uint8_t profile;
        /* src_fid is 16 b */
        uint16_t        src_fid;
        /* dst_fid is 16 b */
        uint16_t        dst_fid;
        /* l2_ctxt_id is 16 b */
        uint16_t        l2_ctxt_id;
        /* em_info is 64 b */
        uint64_t        em_info;
        /* tcam_info is 64 b */
        uint64_t        tcam_info;
        /* vfp_tcam_info is 64 b */
        uint64_t        vfp_tcam_info;
        /* ar_id is 16 b */
        uint16_t        ar_id;
        /* flow_handle is 16 b */
        uint16_t        flow_handle;
        /* tunnel_handle is 32 b */
        uint32_t        tunnel_handle;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_cfa_flow_flush *
 ***********************/


/* hwrm_cfa_flow_flush_input (size:192b/24B) */
struct hwrm_cfa_flow_flush_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_cfa_flow_flush_output (size:128b/16B) */
struct hwrm_cfa_flow_flush_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_cfa_flow_stats *
 ***********************/


/* hwrm_cfa_flow_stats_input (size:320b/40B) */
struct hwrm_cfa_flow_stats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Flow handle. */
        uint16_t        num_flows;
        /* Flow handle. */
        uint16_t        flow_handle_0;
        /* Flow handle. */
        uint16_t        flow_handle_1;
        /* Flow handle. */
        uint16_t        flow_handle_2;
        /* Flow handle. */
        uint16_t        flow_handle_3;
        /* Flow handle. */
        uint16_t        flow_handle_4;
        /* Flow handle. */
        uint16_t        flow_handle_5;
        /* Flow handle. */
        uint16_t        flow_handle_6;
        /* Flow handle. */
        uint16_t        flow_handle_7;
        /* Flow handle. */
        uint16_t        flow_handle_8;
        /* Flow handle. */
        uint16_t        flow_handle_9;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_cfa_flow_stats_output (size:1408b/176B) */
struct hwrm_cfa_flow_stats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* packet_0 is 64 b */
        uint64_t        packet_0;
        /* packet_1 is 64 b */
        uint64_t        packet_1;
        /* packet_2 is 64 b */
        uint64_t        packet_2;
        /* packet_3 is 64 b */
        uint64_t        packet_3;
        /* packet_4 is 64 b */
        uint64_t        packet_4;
        /* packet_5 is 64 b */
        uint64_t        packet_5;
        /* packet_6 is 64 b */
        uint64_t        packet_6;
        /* packet_7 is 64 b */
        uint64_t        packet_7;
        /* packet_8 is 64 b */
        uint64_t        packet_8;
        /* packet_9 is 64 b */
        uint64_t        packet_9;
        /* byte_0 is 64 b */
        uint64_t        byte_0;
        /* byte_1 is 64 b */
        uint64_t        byte_1;
        /* byte_2 is 64 b */
        uint64_t        byte_2;
        /* byte_3 is 64 b */
        uint64_t        byte_3;
        /* byte_4 is 64 b */
        uint64_t        byte_4;
        /* byte_5 is 64 b */
        uint64_t        byte_5;
        /* byte_6 is 64 b */
        uint64_t        byte_6;
        /* byte_7 is 64 b */
        uint64_t        byte_7;
        /* byte_8 is 64 b */
        uint64_t        byte_8;
        /* byte_9 is 64 b */
        uint64_t        byte_9;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_cfa_vf_pair_alloc *
 **************************/


/* hwrm_cfa_vf_pair_alloc_input (size:448b/56B) */
struct hwrm_cfa_vf_pair_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Logical VF number (range: 0 -> MAX_VFS -1). */
        uint16_t        vf_a_id;
        /* Logical VF number (range: 0 -> MAX_VFS -1). */
        uint16_t        vf_b_id;
        uint8_t unused_0[4];
        /* VF Pair name (32 byte string). */
        char    pair_name[32];
} __attribute__((packed));

/* hwrm_cfa_vf_pair_alloc_output (size:128b/16B) */
struct hwrm_cfa_vf_pair_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_cfa_vf_pair_free *
 *************************/


/* hwrm_cfa_vf_pair_free_input (size:384b/48B) */
struct hwrm_cfa_vf_pair_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* VF Pair name (32 byte string). */
        char    pair_name[32];
} __attribute__((packed));

/* hwrm_cfa_vf_pair_free_output (size:128b/16B) */
struct hwrm_cfa_vf_pair_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_cfa_vf_pair_info *
 *************************/


/* hwrm_cfa_vf_pair_info_input (size:448b/56B) */
struct hwrm_cfa_vf_pair_info_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* If this flag is set, lookup by name else lookup by index. */
        #define HWRM_CFA_VF_PAIR_INFO_INPUT_FLAGS_LOOKUP_TYPE     UINT32_C(0x1)
        /* vf pair table index. */
        uint16_t        vf_pair_index;
        uint8_t unused_0[2];
        /* VF Pair name (32 byte string). */
        char    vf_pair_name[32];
} __attribute__((packed));

/* hwrm_cfa_vf_pair_info_output (size:512b/64B) */
struct hwrm_cfa_vf_pair_info_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* vf pair table index. */
        uint16_t        next_vf_pair_index;
        /* vf pair member a's vf_fid. */
        uint16_t        vf_a_fid;
        /* vf pair member a's Linux logical VF number. */
        uint16_t        vf_a_index;
        /* vf pair member b's vf_fid. */
        uint16_t        vf_b_fid;
        /* vf pair member a's Linux logical VF number. */
        uint16_t        vf_b_index;
        /* vf pair state. */
        uint8_t pair_state;
        /* Pair has been allocated */
        #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ALLOCATED UINT32_C(0x1)
        /* Both pair members are active */
        #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE    UINT32_C(0x2)
        #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_LAST \
                HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE
        uint8_t unused_0[5];
        /* VF Pair name (32 byte string). */
        char    pair_name[32];
        uint8_t unused_1[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_cfa_pair_alloc *
 ***********************/


/* hwrm_cfa_pair_alloc_input (size:576b/72B) */
struct hwrm_cfa_pair_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair, 5-rep2fn_mod). */
        uint8_t pair_mode;
        /* Pair between VF on local host with PF or VF on specified host. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_VF2FN         UINT32_C(0x0)
        /* Pair between REP on local host with PF or VF on specified host. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN        UINT32_C(0x1)
        /* Pair between REP on local host with REP on specified host. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2REP       UINT32_C(0x2)
        /* Pair for the proxy interface. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_PROXY         UINT32_C(0x3)
        /* Pair for the PF interface. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_PFPAIR        UINT32_C(0x4)
        /* Modify exiting rep2fn pair and move pair to new PF. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_MOD    UINT32_C(0x5)
        /* Modify exiting rep2fn pairs paired with same PF and move pairs to new PF. */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_MODALL UINT32_C(0x6)
        #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_LAST \
                HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_MODALL
        uint8_t unused_0;
        /* Logical VF number (range: 0 -> MAX_VFS -1). */
        uint16_t        vf_a_id;
        /* Logical Host (0xff-local host). */
        uint8_t host_b_id;
        /* Logical PF (0xff-PF for command channel). */
        uint8_t pf_b_id;
        /* Logical VF number (range: 0 -> MAX_VFS -1). */
        uint16_t        vf_b_id;
        /* Loopback port (0xff-internal loopback), valid for mode-3. */
        uint8_t port_id;
        /* Priority used for encap of loopback packets valid for mode-3. */
        uint8_t pri;
        /* New PF for rep2fn modify, valid for mode 5. */
        uint16_t        new_pf_fid;
        uint32_t        enables;
        /*
         * This bit must be '1' for the q_ab field to be
         * configured.
         */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_Q_AB_VALID      UINT32_C(0x1)
        /*
         * This bit must be '1' for the q_ba field to be
         * configured.
         */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_Q_BA_VALID      UINT32_C(0x2)
        /*
         * This bit must be '1' for the fc_ab field to be
         * configured.
         */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_FC_AB_VALID     UINT32_C(0x4)
        /*
         * This bit must be '1' for the fc_ba field to be
         * configured.
         */
        #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_FC_BA_VALID     UINT32_C(0x8)
        /* VF Pair name (32 byte string). */
        char    pair_name[32];
        /*
         * The q_ab value specifies the logical index of the TX/RX CoS
         * queue to be assigned for traffic in the A to B direction of
         * the interface pair. The default value is 0.
         */
        uint8_t q_ab;
        /*
         * The q_ba value specifies the logical index of the TX/RX CoS
         * queue to be assigned for traffic in the B to A direction of
         * the interface pair. The default value is 1.
         */
        uint8_t q_ba;
        /*
         * Specifies whether RX ring flow control is disabled (0) or enabled
         * (1) in the A to B direction. The default value is 0, meaning that
         * packets will be dropped when the B-side RX rings are full.
         */
        uint8_t fc_ab;
        /*
         * Specifies whether RX ring flow control is disabled (0) or enabled
         * (1) in the B to A direction. The default value is 1, meaning that
         * the RX CoS queue will be flow controlled when the A-side RX rings
         * are full.
         */
        uint8_t fc_ba;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_cfa_pair_alloc_output (size:192b/24B) */
struct hwrm_cfa_pair_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Only valid for modes 1 and 2. */
        uint16_t        rx_cfa_code_a;
        /* Only valid for modes 1 and 2. */
        uint16_t        tx_cfa_action_a;
        /* Only valid for mode 2. */
        uint16_t        rx_cfa_code_b;
        /* Only valid for mode 2. */
        uint16_t        tx_cfa_action_b;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_cfa_pair_free *
 **********************/


/* hwrm_cfa_pair_free_input (size:384b/48B) */
struct hwrm_cfa_pair_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* VF Pair name (32 byte string). */
        char    pair_name[32];
} __attribute__((packed));

/* hwrm_cfa_pair_free_output (size:128b/16B) */
struct hwrm_cfa_pair_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_cfa_pair_info *
 **********************/


/* hwrm_cfa_pair_info_input (size:448b/56B) */
struct hwrm_cfa_pair_info_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        flags;
        /* If this flag is set, lookup by name else lookup by index. */
        #define HWRM_CFA_PAIR_INFO_INPUT_FLAGS_LOOKUP_TYPE      UINT32_C(0x1)
        /* If this flag is set, lookup by PF id and VF id. */
        #define HWRM_CFA_PAIR_INFO_INPUT_FLAGS_LOOKUP_REPRE     UINT32_C(0x2)
        /* Pair table index. */
        uint16_t        pair_index;
        /* Pair pf index. */
        uint8_t pair_pfid;
        /* Pair vf index. */
        uint8_t pair_vfid;
        /* Pair name (32 byte string). */
        char    pair_name[32];
} __attribute__((packed));

/* hwrm_cfa_pair_info_output (size:576b/72B) */
struct hwrm_cfa_pair_info_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Pair table index. */
        uint16_t        next_pair_index;
        /* Pair member a's fid. */
        uint16_t        a_fid;
        /* Logical host number. */
        uint8_t host_a_index;
        /* Logical PF number. */
        uint8_t pf_a_index;
        /* Pair member a's Linux logical VF number. */
        uint16_t        vf_a_index;
        /* Rx CFA code. */
        uint16_t        rx_cfa_code_a;
        /* Tx CFA action. */
        uint16_t        tx_cfa_action_a;
        /* Pair member b's fid. */
        uint16_t        b_fid;
        /* Logical host number. */
        uint8_t host_b_index;
        /* Logical PF number. */
        uint8_t pf_b_index;
        /* Pair member a's Linux logical VF number. */
        uint16_t        vf_b_index;
        /* Rx CFA code. */
        uint16_t        rx_cfa_code_b;
        /* Tx CFA action. */
        uint16_t        tx_cfa_action_b;
        /* Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair). */
        uint8_t pair_mode;
        /* Pair between VF on local host with PF or VF on specified host. */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_VF2FN   UINT32_C(0x0)
        /* Pair between REP on local host with PF or VF on specified host. */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_REP2FN  UINT32_C(0x1)
        /* Pair between REP on local host with REP on specified host. */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_REP2REP UINT32_C(0x2)
        /* Pair for the proxy interface. */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PROXY   UINT32_C(0x3)
        /* Pair for the PF interface. */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PFPAIR  UINT32_C(0x4)
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_LAST \
                HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PFPAIR
        /* Pair state. */
        uint8_t pair_state;
        /* Pair has been allocated */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ALLOCATED UINT32_C(0x1)
        /* Both pair members are active */
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE    UINT32_C(0x2)
        #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_LAST \
                HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE
        /* Pair name (32 byte string). */
        char    pair_name[32];
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_cfa_vfr_alloc *
 **********************/


/* hwrm_cfa_vfr_alloc_input (size:448b/56B) */
struct hwrm_cfa_vfr_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Logical VF number (range: 0 -> MAX_VFS -1). */
        uint16_t        vf_id;
        /*
         * This field is reserved for the future use.
         * It shall be set to 0.
         */
        uint16_t        reserved;
        uint8_t unused_0[4];
        /* VF Representor name (32 byte string). */
        char    vfr_name[32];
} __attribute__((packed));

/* hwrm_cfa_vfr_alloc_output (size:128b/16B) */
struct hwrm_cfa_vfr_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Rx CFA code. */
        uint16_t        rx_cfa_code;
        /* Tx CFA action. */
        uint16_t        tx_cfa_action;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_cfa_vfr_free *
 *********************/


/* hwrm_cfa_vfr_free_input (size:384b/48B) */
struct hwrm_cfa_vfr_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* VF Representor name (32 byte string). */
        char    vfr_name[32];
} __attribute__((packed));

/* hwrm_cfa_vfr_free_output (size:128b/16B) */
struct hwrm_cfa_vfr_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************************
 * hwrm_tunnel_dst_port_query *
 ******************************/


/* hwrm_tunnel_dst_port_query_input (size:192b/24B) */
struct hwrm_tunnel_dst_port_query_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
        #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_IPGRE_V1 \
                UINT32_C(0xa)
        #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_LAST \
                HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_IPGRE_V1
        uint8_t unused_0[7];
} __attribute__((packed));

/* hwrm_tunnel_dst_port_query_output (size:128b/16B) */
struct hwrm_tunnel_dst_port_query_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * This field represents the identifier of L4 destination port
         * used for the given tunnel type. This field is valid for
         * specific tunnel types that use layer 4 (e.g. UDP)
         * transports for tunneling.
         */
        uint16_t        tunnel_dst_port_id;
        /*
         * This field represents the value of L4 destination port
         * identified by tunnel_dst_port_id. This field is valid for
         * specific tunnel types that use layer 4 (e.g. UDP)
         * transports for tunneling.
         * This field is in network byte order.
         *
         * A value of 0 means that the destination port is not
         * configured.
         */
        uint16_t        tunnel_dst_port_val;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************************
 * hwrm_tunnel_dst_port_alloc *
 ******************************/


/* hwrm_tunnel_dst_port_alloc_input (size:192b/24B) */
struct hwrm_tunnel_dst_port_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
        #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
                UINT32_C(0xa)
        #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_LAST \
                HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1
        uint8_t unused_0;
        /*
         * This field represents the value of L4 destination port used
         * for the given tunnel type. This field is valid for
         * specific tunnel types that use layer 4 (e.g. UDP)
         * transports for tunneling.
         *
         * This field is in network byte order.
         *
         * A value of 0 shall fail the command.
         */
        uint16_t        tunnel_dst_port_val;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_tunnel_dst_port_alloc_output (size:128b/16B) */
struct hwrm_tunnel_dst_port_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * Identifier of a tunnel L4 destination port value. Only applies to tunnel
         * types that has l4 destination port parameters.
         */
        uint16_t        tunnel_dst_port_id;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************************
 * hwrm_tunnel_dst_port_free *
 *****************************/


/* hwrm_tunnel_dst_port_free_input (size:192b/24B) */
struct hwrm_tunnel_dst_port_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Tunnel Type. */
        uint8_t tunnel_type;
        /* Virtual eXtensible Local Area Network (VXLAN) */
        #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN \
                UINT32_C(0x1)
        /* Generic Network Virtualization Encapsulation (Geneve) */
        #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_GENEVE \
                UINT32_C(0x5)
        /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
        #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 \
                UINT32_C(0x9)
        /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
        #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_IPGRE_V1 \
                UINT32_C(0xa)
        #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_LAST \
                HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_IPGRE_V1
        uint8_t unused_0;
        /*
         * Identifier of a tunnel L4 destination port value. Only applies to tunnel
         * types that has l4 destination port parameters.
         */
        uint16_t        tunnel_dst_port_id;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_tunnel_dst_port_free_output (size:128b/16B) */
struct hwrm_tunnel_dst_port_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_1[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* ctx_hw_stats (size:1280b/160B) */
struct ctx_hw_stats {
        /* Number of received unicast packets */
        uint64_t        rx_ucast_pkts;
        /* Number of received multicast packets */
        uint64_t        rx_mcast_pkts;
        /* Number of received broadcast packets */
        uint64_t        rx_bcast_pkts;
        /* Number of discarded packets on received path */
        uint64_t        rx_discard_pkts;
        /* Number of dropped packets on received path */
        uint64_t        rx_drop_pkts;
        /* Number of received bytes for unicast traffic */
        uint64_t        rx_ucast_bytes;
        /* Number of received bytes for multicast traffic */
        uint64_t        rx_mcast_bytes;
        /* Number of received bytes for broadcast traffic */
        uint64_t        rx_bcast_bytes;
        /* Number of transmitted unicast packets */
        uint64_t        tx_ucast_pkts;
        /* Number of transmitted multicast packets */
        uint64_t        tx_mcast_pkts;
        /* Number of transmitted broadcast packets */
        uint64_t        tx_bcast_pkts;
        /* Number of discarded packets on transmit path */
        uint64_t        tx_discard_pkts;
        /* Number of dropped packets on transmit path */
        uint64_t        tx_drop_pkts;
        /* Number of transmitted bytes for unicast traffic */
        uint64_t        tx_ucast_bytes;
        /* Number of transmitted bytes for multicast traffic */
        uint64_t        tx_mcast_bytes;
        /* Number of transmitted bytes for broadcast traffic */
        uint64_t        tx_bcast_bytes;
        /* Number of TPA packets */
        uint64_t        tpa_pkts;
        /* Number of TPA bytes */
        uint64_t        tpa_bytes;
        /* Number of TPA events */
        uint64_t        tpa_events;
        /* Number of TPA aborts */
        uint64_t        tpa_aborts;
} __attribute__((packed));

/***********************
 * hwrm_stat_ctx_alloc *
 ***********************/


/* hwrm_stat_ctx_alloc_input (size:256b/32B) */
struct hwrm_stat_ctx_alloc_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* This is the address for statistic block. */
        uint64_t        stats_dma_addr;
        /*
         * The statistic block update period in ms.
         * e.g. 250ms, 500ms, 750ms, 1000ms.
         * If update_period_ms is 0, then the stats update
         * shall be never done and the DMA address shall not be used.
         * In this case, the stat block can only be read by
         * hwrm_stat_ctx_query command.
         */
        uint32_t        update_period_ms;
        /*
         * This field is used to specify statistics context specific
         * configuration flags.
         */
        uint8_t stat_ctx_flags;
        /*
         * When this bit is set to '1', the statistics context shall be
         * allocated for RoCE traffic only. In this case, traffic other
         * than offloaded RoCE traffic shall not be included in this
         * statistic context.
         * When this bit is set to '0', the statistics context shall be
         * used for the network traffic other than offloaded RoCE traffic.
         */
        #define HWRM_STAT_CTX_ALLOC_INPUT_STAT_CTX_FLAGS_ROCE     UINT32_C(0x1)
        uint8_t unused_0[3];
} __attribute__((packed));

/* hwrm_stat_ctx_alloc_output (size:128b/16B) */
struct hwrm_stat_ctx_alloc_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This is the statistics context ID value. */
        uint32_t        stat_ctx_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**********************
 * hwrm_stat_ctx_free *
 **********************/


/* hwrm_stat_ctx_free_input (size:192b/24B) */
struct hwrm_stat_ctx_free_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* ID of the statistics context that is being queried. */
        uint32_t        stat_ctx_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_stat_ctx_free_output (size:128b/16B) */
struct hwrm_stat_ctx_free_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* This is the statistics context ID value. */
        uint32_t        stat_ctx_id;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***********************
 * hwrm_stat_ctx_query *
 ***********************/


/* hwrm_stat_ctx_query_input (size:192b/24B) */
struct hwrm_stat_ctx_query_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* ID of the statistics context that is being queried. */
        uint32_t        stat_ctx_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_stat_ctx_query_output (size:1408b/176B) */
struct hwrm_stat_ctx_query_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Number of transmitted unicast packets */
        uint64_t        tx_ucast_pkts;
        /* Number of transmitted multicast packets */
        uint64_t        tx_mcast_pkts;
        /* Number of transmitted broadcast packets */
        uint64_t        tx_bcast_pkts;
        /* Number of transmitted packets with error */
        uint64_t        tx_err_pkts;
        /* Number of dropped packets on transmit path */
        uint64_t        tx_drop_pkts;
        /* Number of transmitted bytes for unicast traffic */
        uint64_t        tx_ucast_bytes;
        /* Number of transmitted bytes for multicast traffic */
        uint64_t        tx_mcast_bytes;
        /* Number of transmitted bytes for broadcast traffic */
        uint64_t        tx_bcast_bytes;
        /* Number of received unicast packets */
        uint64_t        rx_ucast_pkts;
        /* Number of received multicast packets */
        uint64_t        rx_mcast_pkts;
        /* Number of received broadcast packets */
        uint64_t        rx_bcast_pkts;
        /* Number of received packets with error */
        uint64_t        rx_err_pkts;
        /* Number of dropped packets on received path */
        uint64_t        rx_drop_pkts;
        /* Number of received bytes for unicast traffic */
        uint64_t        rx_ucast_bytes;
        /* Number of received bytes for multicast traffic */
        uint64_t        rx_mcast_bytes;
        /* Number of received bytes for broadcast traffic */
        uint64_t        rx_bcast_bytes;
        /* Number of aggregated unicast packets */
        uint64_t        rx_agg_pkts;
        /* Number of aggregated unicast bytes */
        uint64_t        rx_agg_bytes;
        /* Number of aggregation events */
        uint64_t        rx_agg_events;
        /* Number of aborted aggregations */
        uint64_t        rx_agg_aborts;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_stat_ctx_clr_stats *
 ***************************/


/* hwrm_stat_ctx_clr_stats_input (size:192b/24B) */
struct hwrm_stat_ctx_clr_stats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* ID of the statistics context that is being queried. */
        uint32_t        stat_ctx_id;
        uint8_t unused_0[4];
} __attribute__((packed));

/* hwrm_stat_ctx_clr_stats_output (size:128b/16B) */
struct hwrm_stat_ctx_clr_stats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/********************
 * hwrm_pcie_qstats *
 ********************/


/* hwrm_pcie_qstats_input (size:256b/32B) */
struct hwrm_pcie_qstats_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * The size of PCIe statistics block in bytes.
         * Firmware will DMA the PCIe statistics to
         * the host with this field size in the response.
         */
        uint16_t        pcie_stat_size;
        uint8_t unused_0[6];
        /*
         * This is the host address where
         * PCIe statistics will be stored
         */
        uint64_t        pcie_stat_host_addr;
} __attribute__((packed));

/* hwrm_pcie_qstats_output (size:128b/16B) */
struct hwrm_pcie_qstats_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* The size of PCIe statistics block in bytes. */
        uint16_t        pcie_stat_size;
        uint8_t unused_0[5];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* Port Tx Statistics Formats */
/* tx_port_stats (size:3264b/408B) */
struct tx_port_stats {
        /* Total Number of 64 Bytes frames transmitted */
        uint64_t        tx_64b_frames;
        /* Total Number of 65-127 Bytes frames transmitted */
        uint64_t        tx_65b_127b_frames;
        /* Total Number of 128-255 Bytes frames transmitted */
        uint64_t        tx_128b_255b_frames;
        /* Total Number of 256-511 Bytes frames transmitted */
        uint64_t        tx_256b_511b_frames;
        /* Total Number of 512-1023 Bytes frames transmitted */
        uint64_t        tx_512b_1023b_frames;
        /* Total Number of 1024-1518 Bytes frames transmitted */
        uint64_t        tx_1024b_1518_frames;
        /*
         * Total Number of each good VLAN (exludes FCS errors)
         * frame transmitted which is 1519 to 1522 bytes in length
         * inclusive (excluding framing bits but including FCS bytes).
         */
        uint64_t        tx_good_vlan_frames;
        /* Total Number of 1519-2047 Bytes frames transmitted */
        uint64_t        tx_1519b_2047_frames;
        /* Total Number of 2048-4095 Bytes frames transmitted */
        uint64_t        tx_2048b_4095b_frames;
        /* Total Number of 4096-9216 Bytes frames transmitted */
        uint64_t        tx_4096b_9216b_frames;
        /* Total Number of 9217-16383 Bytes frames transmitted */
        uint64_t        tx_9217b_16383b_frames;
        /* Total Number of good frames transmitted */
        uint64_t        tx_good_frames;
        /* Total Number of frames transmitted */
        uint64_t        tx_total_frames;
        /* Total number of unicast frames transmitted */
        uint64_t        tx_ucast_frames;
        /* Total number of multicast frames transmitted */
        uint64_t        tx_mcast_frames;
        /* Total number of broadcast frames transmitted */
        uint64_t        tx_bcast_frames;
        /* Total number of PAUSE control frames transmitted */
        uint64_t        tx_pause_frames;
        /*
         * Total number of PFC/per-priority PAUSE
         * control frames transmitted
         */
        uint64_t        tx_pfc_frames;
        /* Total number of jabber frames transmitted */
        uint64_t        tx_jabber_frames;
        /* Total number of frames transmitted with FCS error */
        uint64_t        tx_fcs_err_frames;
        /* Total number of control frames transmitted */
        uint64_t        tx_control_frames;
        /* Total number of over-sized frames transmitted */
        uint64_t        tx_oversz_frames;
        /* Total number of frames with single deferral */
        uint64_t        tx_single_dfrl_frames;
        /* Total number of frames with multiple deferrals */
        uint64_t        tx_multi_dfrl_frames;
        /* Total number of frames with single collision */
        uint64_t        tx_single_coll_frames;
        /* Total number of frames with multiple collisions */
        uint64_t        tx_multi_coll_frames;
        /* Total number of frames with late collisions */
        uint64_t        tx_late_coll_frames;
        /* Total number of frames with excessive collisions */
        uint64_t        tx_excessive_coll_frames;
        /* Total number of fragmented frames transmitted */
        uint64_t        tx_frag_frames;
        /* Total number of transmit errors */
        uint64_t        tx_err;
        /* Total number of single VLAN tagged frames transmitted */
        uint64_t        tx_tagged_frames;
        /* Total number of double VLAN tagged frames transmitted */
        uint64_t        tx_dbl_tagged_frames;
        /* Total number of runt frames transmitted */
        uint64_t        tx_runt_frames;
        /* Total number of TX FIFO under runs */
        uint64_t        tx_fifo_underruns;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 0 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri0;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 1 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri1;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 2 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri2;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 3 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri3;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 4 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri4;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 5 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri5;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 6 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri6;
        /*
         * Total number of PFC frames with PFC enabled bit for
         * Pri 7 transmitted
         */
        uint64_t        tx_pfc_ena_frames_pri7;
        /* Total number of EEE LPI Events on TX */
        uint64_t        tx_eee_lpi_events;
        /* EEE LPI Duration Counter on TX */
        uint64_t        tx_eee_lpi_duration;
        /*
         * Total number of Link Level Flow Control (LLFC) messages
         * transmitted
         */
        uint64_t        tx_llfc_logical_msgs;
        /* Total number of HCFC messages transmitted */
        uint64_t        tx_hcfc_msgs;
        /* Total number of TX collisions */
        uint64_t        tx_total_collisions;
        /* Total number of transmitted bytes */
        uint64_t        tx_bytes;
        /* Total number of end-to-end HOL frames */
        uint64_t        tx_xthol_frames;
        /* Total Tx Drops per Port reported by STATS block */
        uint64_t        tx_stat_discard;
        /* Total Tx Error Drops per Port reported by STATS block */
        uint64_t        tx_stat_error;
} __attribute__((packed));

/* Port Rx Statistics Formats */
/* rx_port_stats (size:4224b/528B) */
struct rx_port_stats {
        /* Total Number of 64 Bytes frames received */
        uint64_t        rx_64b_frames;
        /* Total Number of 65-127 Bytes frames received */
        uint64_t        rx_65b_127b_frames;
        /* Total Number of 128-255 Bytes frames received */
        uint64_t        rx_128b_255b_frames;
        /* Total Number of 256-511 Bytes frames received */
        uint64_t        rx_256b_511b_frames;
        /* Total Number of 512-1023 Bytes frames received */
        uint64_t        rx_512b_1023b_frames;
        /* Total Number of 1024-1518 Bytes frames received */
        uint64_t        rx_1024b_1518_frames;
        /*
         * Total Number of each good VLAN (exludes FCS errors)
         * frame received which is 1519 to 1522 bytes in length
         * inclusive (excluding framing bits but including FCS bytes).
         */
        uint64_t        rx_good_vlan_frames;
        /* Total Number of 1519-2047 Bytes frames received */
        uint64_t        rx_1519b_2047b_frames;
        /* Total Number of 2048-4095 Bytes frames received */
        uint64_t        rx_2048b_4095b_frames;
        /* Total Number of 4096-9216 Bytes frames received */
        uint64_t        rx_4096b_9216b_frames;
        /* Total Number of 9217-16383 Bytes frames received */
        uint64_t        rx_9217b_16383b_frames;
        /* Total number of frames received */
        uint64_t        rx_total_frames;
        /* Total number of unicast frames received */
        uint64_t        rx_ucast_frames;
        /* Total number of multicast frames received */
        uint64_t        rx_mcast_frames;
        /* Total number of broadcast frames received */
        uint64_t        rx_bcast_frames;
        /* Total number of received frames with FCS error */
        uint64_t        rx_fcs_err_frames;
        /* Total number of control frames received */
        uint64_t        rx_ctrl_frames;
        /* Total number of PAUSE frames received */
        uint64_t        rx_pause_frames;
        /* Total number of PFC frames received */
        uint64_t        rx_pfc_frames;
        /*
         * Total number of frames received with an unsupported
         * opcode
         */
        uint64_t        rx_unsupported_opcode_frames;
        /*
         * Total number of frames received with an unsupported
         * DA for pause and PFC
         */
        uint64_t        rx_unsupported_da_pausepfc_frames;
        /* Total number of frames received with an unsupported SA */
        uint64_t        rx_wrong_sa_frames;
        /* Total number of received packets with alignment error */
        uint64_t        rx_align_err_frames;
        /* Total number of received frames with out-of-range length */
        uint64_t        rx_oor_len_frames;
        /* Total number of received frames with error termination */
        uint64_t        rx_code_err_frames;
        /*
         * Total number of received frames with a false carrier is
         * detected during idle, as defined by RX_ER samples active
         * and RXD is 0xE. The event is reported along with the
         * statistics generated on the next received frame. Only
         * one false carrier condition can be detected and logged
         * between frames.
         *
         * Carrier event, valid for 10M/100M speed modes only.
         */
        uint64_t        rx_false_carrier_frames;
        /* Total number of over-sized frames received */
        uint64_t        rx_ovrsz_frames;
        /* Total number of jabber packets received */
        uint64_t        rx_jbr_frames;
        /* Total number of received frames with MTU error */
        uint64_t        rx_mtu_err_frames;
        /* Total number of received frames with CRC match */
        uint64_t        rx_match_crc_frames;
        /* Total number of frames received promiscuously */
        uint64_t        rx_promiscuous_frames;
        /*
         * Total number of received frames with one or two VLAN
         * tags
         */
        uint64_t        rx_tagged_frames;
        /* Total number of received frames with two VLAN tags */
        uint64_t        rx_double_tagged_frames;
        /* Total number of truncated frames received */
        uint64_t        rx_trunc_frames;
        /* Total number of good frames (without errors) received */
        uint64_t        rx_good_frames;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 0
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri0;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 1
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri1;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 2
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri2;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 3
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri3;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 4
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri4;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 5
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri5;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 6
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri6;
        /*
         * Total number of received PFC frames with transition from
         * XON to XOFF on Pri 7
         */
        uint64_t        rx_pfc_xon2xoff_frames_pri7;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 0
         */
        uint64_t        rx_pfc_ena_frames_pri0;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 1
         */
        uint64_t        rx_pfc_ena_frames_pri1;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 2
         */
        uint64_t        rx_pfc_ena_frames_pri2;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 3
         */
        uint64_t        rx_pfc_ena_frames_pri3;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 4
         */
        uint64_t        rx_pfc_ena_frames_pri4;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 5
         */
        uint64_t        rx_pfc_ena_frames_pri5;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 6
         */
        uint64_t        rx_pfc_ena_frames_pri6;
        /*
         * Total number of received PFC frames with PFC enabled
         * bit for Pri 7
         */
        uint64_t        rx_pfc_ena_frames_pri7;
        /* Total Number of frames received with SCH CRC error */
        uint64_t        rx_sch_crc_err_frames;
        /* Total Number of under-sized frames received */
        uint64_t        rx_undrsz_frames;
        /* Total Number of fragmented frames received */
        uint64_t        rx_frag_frames;
        /* Total number of RX EEE LPI Events */
        uint64_t        rx_eee_lpi_events;
        /* EEE LPI Duration Counter on RX */
        uint64_t        rx_eee_lpi_duration;
        /*
         * Total number of physical type Link Level Flow Control
         * (LLFC) messages received
         */
        uint64_t        rx_llfc_physical_msgs;
        /*
         * Total number of logical type Link Level Flow Control
         * (LLFC) messages received
         */
        uint64_t        rx_llfc_logical_msgs;
        /*
         * Total number of logical type Link Level Flow Control
         * (LLFC) messages received with CRC error
         */
        uint64_t        rx_llfc_msgs_with_crc_err;
        /* Total number of HCFC messages received */
        uint64_t        rx_hcfc_msgs;
        /* Total number of HCFC messages received with CRC error */
        uint64_t        rx_hcfc_msgs_with_crc_err;
        /* Total number of received bytes */
        uint64_t        rx_bytes;
        /* Total number of bytes received in runt frames */
        uint64_t        rx_runt_bytes;
        /* Total number of runt frames received */
        uint64_t        rx_runt_frames;
        /* Total Rx Discards per Port reported by STATS block */
        uint64_t        rx_stat_discard;
        uint64_t        rx_stat_err;
} __attribute__((packed));

/* Port Rx Statistics extended Formats */
/* rx_port_stats_ext (size:320b/40B) */
struct rx_port_stats_ext {
        /* Number of times link state changed to down */
        uint64_t        link_down_events;
        /* Number of times the idle rings with pause bit are found */
        uint64_t        continuous_pause_events;
        /* Number of times the active rings pause bit resumed back */
        uint64_t        resume_pause_events;
        /* Number of times, the ROCE cos queue PFC is disabled to avoid pause flood/burst */
        uint64_t        continuous_roce_pause_events;
        /* Number of times, the ROCE cos queue PFC is enabled back */
        uint64_t        resume_roce_pause_events;
} __attribute__((packed));

/* PCIe Statistics Formats */
/* pcie_ctx_hw_stats (size:768b/96B) */
struct pcie_ctx_hw_stats {
        /* Number of physical layer receiver errors */
        uint64_t        pcie_pl_signal_integrity;
        /* Number of DLLP CRC errors detected by Data Link Layer */
        uint64_t        pcie_dl_signal_integrity;
        /*
         * Number of TLP LCRC and sequence number errors detected
         * by Data Link Layer
         */
        uint64_t        pcie_tl_signal_integrity;
        /* Number of times LTSSM entered Recovery state */
        uint64_t        pcie_link_integrity;
        /* Number of TLP bytes that have been trasmitted */
        uint64_t        pcie_tx_traffic_rate;
        /* Number of TLP bytes that have been received */
        uint64_t        pcie_rx_traffic_rate;
        /* Number of DLLP bytes that have been trasmitted */
        uint64_t        pcie_tx_dllp_statistics;
        /* Number of DLLP bytes that have been received */
        uint64_t        pcie_rx_dllp_statistics;
        /*
         * Number of times spent in each phase of gen3
         * equalization
         */
        uint64_t        pcie_equalization_time;
        /* Records the last 16 transitions of the LTSSM */
        uint32_t        pcie_ltssm_histogram[4];
        /*
         * Record the last 8 reasons on why LTSSM transitioned
         * to Recovery
         */
        uint64_t        pcie_recovery_histogram;
} __attribute__((packed));

/**********************
 * hwrm_exec_fwd_resp *
 **********************/


/* hwrm_exec_fwd_resp_input (size:1024b/128B) */
struct hwrm_exec_fwd_resp_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is an encapsulated request. This request should
         * be executed by the HWRM and the response should be
         * provided in the response buffer inside the encapsulated
         * request.
         */
        uint32_t        encap_request[26];
        /*
         * This value indicates the target id of the response to
         * the encapsulated request.
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - HWRM
         */
        uint16_t        encap_resp_target_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_exec_fwd_resp_output (size:128b/16B) */
struct hwrm_exec_fwd_resp_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/************************
 * hwrm_reject_fwd_resp *
 ************************/


/* hwrm_reject_fwd_resp_input (size:1024b/128B) */
struct hwrm_reject_fwd_resp_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is an encapsulated request. This request should
         * be rejected by the HWRM and the error response should be
         * provided in the response buffer inside the encapsulated
         * request.
         */
        uint32_t        encap_request[26];
        /*
         * This value indicates the target id of the response to
         * the encapsulated request.
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - HWRM
         */
        uint16_t        encap_resp_target_id;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_reject_fwd_resp_output (size:128b/16B) */
struct hwrm_reject_fwd_resp_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************
 * hwrm_fwd_resp *
 *****************/


/* hwrm_fwd_resp_input (size:1024b/128B) */
struct hwrm_fwd_resp_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This value indicates the target id of the encapsulated
         * response.
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - HWRM
         */
        uint16_t        encap_resp_target_id;
        /*
         * This value indicates the completion ring the encapsulated
         * response will be optionally completed on.  If the value is
         * -1, then no CR completion shall be generated for the
         * encapsulated response. Any other value must be a
         * valid CR ring_id value. If a valid encap_resp_cmpl_ring
         * is provided, then a CR completion shall be generated for
         * the encapsulated response.
         */
        uint16_t        encap_resp_cmpl_ring;
        /* This field indicates the length of encapsulated response. */
        uint16_t        encap_resp_len;
        uint8_t unused_0;
        uint8_t unused_1;
        /*
         * This is the host address where the encapsulated response
         * will be written.
         * This area must be 16B aligned and must be cleared to zero
         * before the original request is made.
         */
        uint64_t        encap_resp_addr;
        /* This is an encapsulated response. */
        uint32_t        encap_resp[24];
} __attribute__((packed));

/* hwrm_fwd_resp_output (size:128b/16B) */
struct hwrm_fwd_resp_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************************
 * hwrm_fwd_async_event_cmpl *
 *****************************/


/* hwrm_fwd_async_event_cmpl_input (size:320b/40B) */
struct hwrm_fwd_async_event_cmpl_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This value indicates the target id of the encapsulated
         * asynchronous event.
         * 0x0 - 0xFFF8 - Used for function ids
         * 0xFFF8 - 0xFFFE - Reserved for internal processors
         * 0xFFFF - Broadcast to all children VFs (only applicable when
         * a PF is the requester)
         */
        uint16_t        encap_async_event_target_id;
        uint8_t unused_0[6];
        /* This is an encapsulated asynchronous event completion. */
        uint32_t        encap_async_event_cmpl[4];
} __attribute__((packed));

/* hwrm_fwd_async_event_cmpl_output (size:128b/16B) */
struct hwrm_fwd_async_event_cmpl_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_nvm_raw_write_blk *
 **************************/


/* hwrm_nvm_raw_write_blk_input (size:256b/32B) */
struct hwrm_nvm_raw_write_blk_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * 64-bit Host Source Address.
         * This is the loation of the source data to be written.
         */
        uint64_t        host_src_addr;
        /*
         * 32-bit Destination Address.
         * This is the NVRAM byte-offset where the source data will be written to.
         */
        uint32_t        dest_addr;
        /* Length of data to be written, in bytes. */
        uint32_t        len;
} __attribute__((packed));

/* hwrm_nvm_raw_write_blk_output (size:128b/16B) */
struct hwrm_nvm_raw_write_blk_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*****************
 * hwrm_nvm_read *
 *****************/


/* hwrm_nvm_read_input (size:320b/40B) */
struct hwrm_nvm_read_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * 64-bit Host Destination Address.
         * This is the host address where the data will be written to.
         */
        uint64_t        host_dest_addr;
        /* The 0-based index of the directory entry. */
        uint16_t        dir_idx;
        uint8_t unused_0[2];
        /* The NVRAM byte-offset to read from. */
        uint32_t        offset;
        /* The length of the data to be read, in bytes. */
        uint32_t        len;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_nvm_read_output (size:128b/16B) */
struct hwrm_nvm_read_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*********************
 * hwrm_nvm_raw_dump *
 *********************/


/* hwrm_nvm_raw_dump_input (size:256b/32B) */
struct hwrm_nvm_raw_dump_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * 64-bit Host Destination Address.
         * This is the host address where the data will be written to.
         */
        uint64_t        host_dest_addr;
        /* 32-bit NVRAM byte-offset to read from. */
        uint32_t        offset;
        /* Total length of NVRAM contents to be read, in bytes. */
        uint32_t        len;
} __attribute__((packed));

/* hwrm_nvm_raw_dump_output (size:128b/16B) */
struct hwrm_nvm_raw_dump_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/****************************
 * hwrm_nvm_get_dir_entries *
 ****************************/


/* hwrm_nvm_get_dir_entries_input (size:192b/24B) */
struct hwrm_nvm_get_dir_entries_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * 64-bit Host Destination Address.
         * This is the host address where the directory will be written.
         */
        uint64_t        host_dest_addr;
} __attribute__((packed));

/* hwrm_nvm_get_dir_entries_output (size:128b/16B) */
struct hwrm_nvm_get_dir_entries_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_nvm_get_dir_info *
 *************************/


/* hwrm_nvm_get_dir_info_input (size:128b/16B) */
struct hwrm_nvm_get_dir_info_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_nvm_get_dir_info_output (size:192b/24B) */
struct hwrm_nvm_get_dir_info_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Number of directory entries in the directory. */
        uint32_t        entries;
        /* Size of each directory entry, in bytes. */
        uint32_t        entry_length;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/******************
 * hwrm_nvm_write *
 ******************/


/* hwrm_nvm_write_input (size:384b/48B) */
struct hwrm_nvm_write_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * 64-bit Host Source Address.
         * This is where the source data is.
         */
        uint64_t        host_src_addr;
        /* The Directory Entry Type (valid values are defined in the bnxnvm_directory_type enum defined in the file bnxnvm_defs.h). */
        uint16_t        dir_type;
        /*
         * Directory ordinal.
         * The 0-based instance of the combined Directory Entry Type and Extension.
         */
        uint16_t        dir_ordinal;
        /* The Directory Entry Extension flags (see BNX_DIR_EXT_* in the file bnxnvm_defs.h). */
        uint16_t        dir_ext;
        /* Directory Entry Attribute flags (see BNX_DIR_ATTR_* in the file bnxnvm_defs.h). */
        uint16_t        dir_attr;
        /*
         * Length of data to write, in bytes. May be less than or equal to the allocated size for the directory entry.
         * The data length stored in the directory entry will be updated to reflect this value once the write is complete.
         */
        uint32_t        dir_data_length;
        /* Option. */
        uint16_t        option;
        uint16_t        flags;
        /*
         * When this bit is '1', the original active image
         * will not be removed. TBD: what purpose is this?
         */
        #define HWRM_NVM_WRITE_INPUT_FLAGS_KEEP_ORIG_ACTIVE_IMG \
                UINT32_C(0x1)
        /*
         * The requested length of the allocated NVM for the item, in bytes. This value may be greater than or equal to the specified data length (dir_data_length).
         * If this value is less than the specified data length, it will be ignored.
         * The response will contain the actual allocated item length, which may be greater than the requested item length.
         * The purpose for allocating more than the required number of bytes for an item's data is to pre-allocate extra storage (padding) to accomodate
         * the potential future growth of an item (e.g. upgraded firmware with a size increase, log growth, expanded configuration data).
         */
        uint32_t        dir_item_length;
        uint32_t        unused_0;
} __attribute__((packed));

/* hwrm_nvm_write_output (size:128b/16B) */
struct hwrm_nvm_write_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * Length of the allocated NVM for the item, in bytes. The value may be greater than or equal to the specified data length or the requested item length.
         * The actual item length used when creating a new directory entry will be a multiple of an NVM block size.
         */
        uint32_t        dir_item_length;
        /* The directory index of the created or modified item. */
        uint16_t        dir_idx;
        uint8_t unused_0;
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_write_cmd_err (size:64b/8B) */
struct hwrm_nvm_write_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_WRITE_CMD_ERR_CODE_UNKNOWN  UINT32_C(0x0)
        /* Unable to complete operation due to fragmentation */
        #define HWRM_NVM_WRITE_CMD_ERR_CODE_FRAG_ERR UINT32_C(0x1)
        /* nvm is completely full. */
        #define HWRM_NVM_WRITE_CMD_ERR_CODE_NO_SPACE UINT32_C(0x2)
        #define HWRM_NVM_WRITE_CMD_ERR_CODE_LAST \
                HWRM_NVM_WRITE_CMD_ERR_CODE_NO_SPACE
        uint8_t unused_0[7];
} __attribute__((packed));

/*******************
 * hwrm_nvm_modify *
 *******************/


/* hwrm_nvm_modify_input (size:320b/40B) */
struct hwrm_nvm_modify_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * 64-bit Host Source Address.
         * This is where the modified data is.
         */
        uint64_t        host_src_addr;
        /* 16-bit directory entry index. */
        uint16_t        dir_idx;
        uint8_t unused_0[2];
        /* 32-bit NVRAM byte-offset to modify content from. */
        uint32_t        offset;
        /*
         * Length of data to be modified, in bytes. The length shall
         * be non-zero.
         */
        uint32_t        len;
        uint8_t unused_1[4];
} __attribute__((packed));

/* hwrm_nvm_modify_output (size:128b/16B) */
struct hwrm_nvm_modify_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_nvm_find_dir_entry *
 ***************************/


/* hwrm_nvm_find_dir_entry_input (size:256b/32B) */
struct hwrm_nvm_find_dir_entry_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the dir_idx_valid field to be
         * configured.
         */
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_ENABLES_DIR_IDX_VALID \
                UINT32_C(0x1)
        /* Directory Entry Index */
        uint16_t        dir_idx;
        /* Directory Entry (Image) Type */
        uint16_t        dir_type;
        /*
         * Directory ordinal.
         * The instance of this Directory Type
         */
        uint16_t        dir_ordinal;
        /* The Directory Entry Extension flags. */
        uint16_t        dir_ext;
        /* This value indicates the search option using dir_ordinal. */
        uint8_t opt_ordinal;
        /* This value indicates the search option using dir_ordinal. */
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_MASK UINT32_C(0x3)
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_SFT 0
        /* Equal to specified ordinal value. */
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_EQ    UINT32_C(0x0)
        /* Greater than or equal to specified ordinal value */
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_GE    UINT32_C(0x1)
        /* Greater than specified ordinal value */
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_GT    UINT32_C(0x2)
        #define HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_LAST \
                HWRM_NVM_FIND_DIR_ENTRY_INPUT_OPT_ORDINAL_GT
        uint8_t unused_0[3];
} __attribute__((packed));

/* hwrm_nvm_find_dir_entry_output (size:256b/32B) */
struct hwrm_nvm_find_dir_entry_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Allocated NVRAM for this directory entry, in bytes. */
        uint32_t        dir_item_length;
        /* Size of the stored data for this directory entry, in bytes. */
        uint32_t        dir_data_length;
        /*
         * Firmware version.
         * Only valid if the directory entry is for embedded firmware stored in APE_BIN Format.
         */
        uint32_t        fw_ver;
        /* Directory ordinal. */
        uint16_t        dir_ordinal;
        /* Directory Entry Index */
        uint16_t        dir_idx;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/****************************
 * hwrm_nvm_erase_dir_entry *
 ****************************/


/* hwrm_nvm_erase_dir_entry_input (size:192b/24B) */
struct hwrm_nvm_erase_dir_entry_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Directory Entry Index */
        uint16_t        dir_idx;
        uint8_t unused_0[6];
} __attribute__((packed));

/* hwrm_nvm_erase_dir_entry_output (size:128b/16B) */
struct hwrm_nvm_erase_dir_entry_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/*************************
 * hwrm_nvm_get_dev_info *
 *************************/


/* hwrm_nvm_get_dev_info_input (size:128b/16B) */
struct hwrm_nvm_get_dev_info_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_nvm_get_dev_info_output (size:256b/32B) */
struct hwrm_nvm_get_dev_info_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* Manufacturer ID. */
        uint16_t        manufacturer_id;
        /* Device ID. */
        uint16_t        device_id;
        /* Sector size of the NVRAM device. */
        uint32_t        sector_size;
        /* Total size, in bytes of the NVRAM device. */
        uint32_t        nvram_size;
        uint32_t        reserved_size;
        /* Available size that can be used, in bytes.  Available size is the NVRAM size take away the used size and reserved size. */
        uint32_t        available_size;
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_nvm_mod_dir_entry *
 **************************/


/* hwrm_nvm_mod_dir_entry_input (size:256b/32B) */
struct hwrm_nvm_mod_dir_entry_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        uint32_t        enables;
        /*
         * This bit must be '1' for the checksum field to be
         * configured.
         */
        #define HWRM_NVM_MOD_DIR_ENTRY_INPUT_ENABLES_CHECKSUM     UINT32_C(0x1)
        /* Directory Entry Index */
        uint16_t        dir_idx;
        /*
         * Directory ordinal.
         * The (0-based) instance of this Directory Type.
         */
        uint16_t        dir_ordinal;
        /* The Directory Entry Extension flags (see BNX_DIR_EXT_* for extension flag definitions). */
        uint16_t        dir_ext;
        /* Directory Entry Attribute flags (see BNX_DIR_ATTR_* for attribute flag definitions). */
        uint16_t        dir_attr;
        /*
         * If valid, then this field updates the checksum
         * value of the content in the directory entry.
         */
        uint32_t        checksum;
} __attribute__((packed));

/* hwrm_nvm_mod_dir_entry_output (size:128b/16B) */
struct hwrm_nvm_mod_dir_entry_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/**************************
 * hwrm_nvm_verify_update *
 **************************/


/* hwrm_nvm_verify_update_input (size:192b/24B) */
struct hwrm_nvm_verify_update_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* Directory Entry Type, to be verified. */
        uint16_t        dir_type;
        /*
         * Directory ordinal.
         * The instance of the Directory Type to be verified.
         */
        uint16_t        dir_ordinal;
        /*
         * The Directory Entry Extension flags.
         * The "UPDATE" extension flag must be set in this value.
         * A corresponding directory entry with the same type and ordinal values but *without*
         * the "UPDATE" extension flag must also exist. The other flags of the extension must
         * be identical between the active and update entries.
         */
        uint16_t        dir_ext;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_nvm_verify_update_output (size:128b/16B) */
struct hwrm_nvm_verify_update_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/***************************
 * hwrm_nvm_install_update *
 ***************************/


/* hwrm_nvm_install_update_input (size:192b/24B) */
struct hwrm_nvm_install_update_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * Installation type. If the value 3 through 0xffff is used,
         * only packaged items with that type value will be installed and
         * conditional installation directives for those packaged items
         * will be over-ridden (i.e. 'create' or 'replace' will be treated
         * as 'install').
         */
        uint32_t        install_type;
        /*
         * Perform a normal package installation. Conditional installation
         * directives (e.g. 'create' and 'replace') of packaged items
         * will be followed.
         */
        #define HWRM_NVM_INSTALL_UPDATE_INPUT_INSTALL_TYPE_NORMAL UINT32_C(0x0)
        /*
         * Install all packaged items regardless of installation directive
         * (i.e. treat all packaged items as though they have an installation
         * directive of 'install').
         */
        #define HWRM_NVM_INSTALL_UPDATE_INPUT_INSTALL_TYPE_ALL \
                UINT32_C(0xffffffff)
        #define HWRM_NVM_INSTALL_UPDATE_INPUT_INSTALL_TYPE_LAST \
                HWRM_NVM_INSTALL_UPDATE_INPUT_INSTALL_TYPE_ALL
        uint16_t        flags;
        /* If set to 1, then securely erase all unused locations in persistent storage. */
        #define HWRM_NVM_INSTALL_UPDATE_INPUT_FLAGS_ERASE_UNUSED_SPACE \
                UINT32_C(0x1)
        /*
         * If set to 1, then unspecifed images, images not in the package file, will be safely deleted.
         * When combined with erase_unused_space then unspecified images will be securely erased.
         */
        #define HWRM_NVM_INSTALL_UPDATE_INPUT_FLAGS_REMOVE_UNUSED_PKG \
                UINT32_C(0x2)
        /*
         * If set to 1, FW will defragment the NVM if defragmentation is required for the update.
         * Allow additional time for this command to complete if this bit is set to 1.
         */
        #define HWRM_NVM_INSTALL_UPDATE_INPUT_FLAGS_ALLOWED_TO_DEFRAG \
                UINT32_C(0x4)
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_nvm_install_update_output (size:192b/24B) */
struct hwrm_nvm_install_update_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /*
         * Bit-mask of successfully installed items.
         * Bit-0 corresponding to the first packaged item, Bit-1 for the second item, etc.
         * A value of 0 indicates that no items were successfully installed.
         */
        uint64_t        installed_items;
        /* result is 8 b */
        uint8_t result;
        /* There was no problem with the package installation. */
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESULT_SUCCESS UINT32_C(0x0)
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESULT_LAST \
                HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESULT_SUCCESS
        /* problem_item is 8 b */
        uint8_t problem_item;
        /* There was no problem with any packaged items. */
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_PROBLEM_ITEM_NONE \
                UINT32_C(0x0)
        /* There was a problem with the NVM package itself. */
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_PROBLEM_ITEM_PACKAGE \
                UINT32_C(0xff)
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_PROBLEM_ITEM_LAST \
                HWRM_NVM_INSTALL_UPDATE_OUTPUT_PROBLEM_ITEM_PACKAGE
        /* reset_required is 8 b */
        uint8_t reset_required;
        /*
         * No reset is required for installed/updated firmware or
         * microcode to take effect.
         */
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_REQUIRED_NONE \
                UINT32_C(0x0)
        /*
         * A PCIe reset (e.g. system reboot) is
         * required for newly installed/updated firmware or
         * microcode to take effect.
         */
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_REQUIRED_PCI \
                UINT32_C(0x1)
        /*
         * A controller power reset (e.g. system power-cycle) is
         * required for newly installed/updated firmware or
         * microcode to take effect. Some newly installed/updated
         * firmware or microcode may still take effect upon the
         * next PCIe reset.
         */
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_REQUIRED_POWER \
                UINT32_C(0x2)
        #define HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_REQUIRED_LAST \
                HWRM_NVM_INSTALL_UPDATE_OUTPUT_RESET_REQUIRED_POWER
        uint8_t unused_0[4];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_install_update_cmd_err (size:64b/8B) */
struct hwrm_nvm_install_update_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_UNKNOWN  UINT32_C(0x0)
        /* Unable to complete operation due to fragmentation */
        #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR UINT32_C(0x1)
        /* nvm is completely full. */
        #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_NO_SPACE UINT32_C(0x2)
        #define HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_LAST \
                HWRM_NVM_INSTALL_UPDATE_CMD_ERR_CODE_NO_SPACE
        uint8_t unused_0[7];
} __attribute__((packed));

/******************
 * hwrm_nvm_flush *
 ******************/


/* hwrm_nvm_flush_input (size:128b/16B) */
struct hwrm_nvm_flush_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
} __attribute__((packed));

/* hwrm_nvm_flush_output (size:128b/16B) */
struct hwrm_nvm_flush_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_flush_cmd_err (size:64b/8B) */
struct hwrm_nvm_flush_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_FLUSH_CMD_ERR_CODE_UNKNOWN UINT32_C(0x0)
        /* flush could not be performed */
        #define HWRM_NVM_FLUSH_CMD_ERR_CODE_FAIL    UINT32_C(0x1)
        #define HWRM_NVM_FLUSH_CMD_ERR_CODE_LAST \
                HWRM_NVM_FLUSH_CMD_ERR_CODE_FAIL
        uint8_t unused_0[7];
} __attribute__((packed));

/*************************
 * hwrm_nvm_get_variable *
 *************************/


/* hwrm_nvm_get_variable_input (size:320b/40B) */
struct hwrm_nvm_get_variable_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is the host address where
         * nvm variable will be stored
         */
        uint64_t        dest_data_addr;
        /* size of data in bits */
        uint16_t        data_len;
        /* nvm cfg option number */
        uint16_t        option_num;
        /* reserved. */
        #define HWRM_NVM_GET_VARIABLE_INPUT_OPTION_NUM_RSVD_0    UINT32_C(0x0)
        /* reserved. */
        #define HWRM_NVM_GET_VARIABLE_INPUT_OPTION_NUM_RSVD_FFFF \
                UINT32_C(0xffff)
        #define HWRM_NVM_GET_VARIABLE_INPUT_OPTION_NUM_LAST \
                HWRM_NVM_GET_VARIABLE_INPUT_OPTION_NUM_RSVD_FFFF
        /*
         * Number of dimensions for this nvm configuration variable.
         * This value indicates how many of the indexN values to use.
         * A value of 0 means that none of the indexN values are valid.
         * A value of 1 requires at index0 is valued, a value of 2
         * requires that index0 and index1 are valid, and so forth
         */
        uint16_t        dimensions;
        /* index for the 1st dimensions */
        uint16_t        index_0;
        /* index for the 2nd dimensions */
        uint16_t        index_1;
        /* index for the 3rd dimensions */
        uint16_t        index_2;
        /* index for the 4th dimensions */
        uint16_t        index_3;
        uint8_t flags;
        /*
         * When this bit is set to 1, the factory default value will be returned,
         * 0 returns the operational value.
         */
        #define HWRM_NVM_GET_VARIABLE_INPUT_FLAGS_FACTORY_DFLT \
                UINT32_C(0x1)
        uint8_t unused_0;
} __attribute__((packed));

/* hwrm_nvm_get_variable_output (size:128b/16B) */
struct hwrm_nvm_get_variable_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        /* size of data of the actual variable retrieved in bits */
        uint16_t        data_len;
        /*
         * option_num is the option number for the data retrieved.  It is possible in the
         * future that the option number returned would be different than requested.  This
         * condition could occur if an option is deprecated and a new option id is defined
         * with similar characteristics, but has a slightly different definition.  This
         * also makes it convenient for the caller to identify the variable result with
         * the option id from the response.
         */
        uint16_t        option_num;
        /* reserved. */
        #define HWRM_NVM_GET_VARIABLE_OUTPUT_OPTION_NUM_RSVD_0    UINT32_C(0x0)
        /* reserved. */
        #define HWRM_NVM_GET_VARIABLE_OUTPUT_OPTION_NUM_RSVD_FFFF \
                UINT32_C(0xffff)
        #define HWRM_NVM_GET_VARIABLE_OUTPUT_OPTION_NUM_LAST \
                HWRM_NVM_GET_VARIABLE_OUTPUT_OPTION_NUM_RSVD_FFFF
        uint8_t unused_0[3];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_get_variable_cmd_err (size:64b/8B) */
struct hwrm_nvm_get_variable_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_UNKNOWN       UINT32_C(0x0)
        /* variable does not exist */
        #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_VAR_NOT_EXIST UINT32_C(0x1)
        /* configuration is corrupted and the variable cannot be saved */
        #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_CORRUPT_VAR   UINT32_C(0x2)
        /* length specified is too small */
        #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_LEN_TOO_SHORT UINT32_C(0x3)
        #define HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_LAST \
                HWRM_NVM_GET_VARIABLE_CMD_ERR_CODE_LEN_TOO_SHORT
        uint8_t unused_0[7];
} __attribute__((packed));

/*************************
 * hwrm_nvm_set_variable *
 *************************/


/* hwrm_nvm_set_variable_input (size:320b/40B) */
struct hwrm_nvm_set_variable_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is the host address where
         * nvm variable will be copied from
         */
        uint64_t        src_data_addr;
        /* size of data in bits */
        uint16_t        data_len;
        /* nvm cfg option number */
        uint16_t        option_num;
        /* reserved. */
        #define HWRM_NVM_SET_VARIABLE_INPUT_OPTION_NUM_RSVD_0    UINT32_C(0x0)
        /* reserved. */
        #define HWRM_NVM_SET_VARIABLE_INPUT_OPTION_NUM_RSVD_FFFF \
                UINT32_C(0xffff)
        #define HWRM_NVM_SET_VARIABLE_INPUT_OPTION_NUM_LAST \
                HWRM_NVM_SET_VARIABLE_INPUT_OPTION_NUM_RSVD_FFFF
        /*
         * Number of dimensions for this nvm configuration variable.
         * This value indicates how many of the indexN values to use.
         * A value of 0 means that none of the indexN values are valid.
         * A value of 1 requires at index0 is valued, a value of 2
         * requires that index0 and index1 are valid, and so forth
         */
        uint16_t        dimensions;
        /* index for the 1st dimensions */
        uint16_t        index_0;
        /* index for the 2nd dimensions */
        uint16_t        index_1;
        /* index for the 3rd dimensions */
        uint16_t        index_2;
        /* index for the 4th dimensions */
        uint16_t        index_3;
        uint8_t flags;
        /* When this bit is 1, flush internal cache after this write operation (see hwrm_nvm_flush command.) */
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_FORCE_FLUSH \
                UINT32_C(0x1)
        /* encryption method */
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_MASK \
                UINT32_C(0xe)
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_SFT           1
        /* No encryption. */
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_NONE \
                (UINT32_C(0x0) << 1)
        /* one-way encryption. */
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_HMAC_SHA1 \
                (UINT32_C(0x1) << 1)
        /* symmetric AES256 encryption. */
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_AES256 \
                (UINT32_C(0x2) << 1)
        /* SHA1 digest appended to plaintext contents, for authentication */
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_HMAC_SHA1_AUTH \
                (UINT32_C(0x3) << 1)
        #define HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_LAST \
                HWRM_NVM_SET_VARIABLE_INPUT_FLAGS_ENCRYPT_MODE_HMAC_SHA1_AUTH
        uint8_t unused_0;
} __attribute__((packed));

/* hwrm_nvm_set_variable_output (size:128b/16B) */
struct hwrm_nvm_set_variable_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t unused_0[7];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_set_variable_cmd_err (size:64b/8B) */
struct hwrm_nvm_set_variable_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_UNKNOWN       UINT32_C(0x0)
        /* variable does not exist */
        #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_VAR_NOT_EXIST UINT32_C(0x1)
        /* configuration is corrupted and the variable cannot be saved */
        #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_CORRUPT_VAR   UINT32_C(0x2)
        #define HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_LAST \
                HWRM_NVM_SET_VARIABLE_CMD_ERR_CODE_CORRUPT_VAR
        uint8_t unused_0[7];
} __attribute__((packed));

/****************************
 * hwrm_nvm_validate_option *
 ****************************/


/* hwrm_nvm_validate_option_input (size:320b/40B) */
struct hwrm_nvm_validate_option_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /*
         * This is the host address where
         * nvm variable will be copied from
         */
        uint64_t        src_data_addr;
        /* size of data in bits */
        uint16_t        data_len;
        /* nvm cfg option number */
        uint16_t        option_num;
        /* reserved. */
        #define HWRM_NVM_VALIDATE_OPTION_INPUT_OPTION_NUM_RSVD_0 \
                UINT32_C(0x0)
        /* reserved. */
        #define HWRM_NVM_VALIDATE_OPTION_INPUT_OPTION_NUM_RSVD_FFFF \
                UINT32_C(0xffff)
        #define HWRM_NVM_VALIDATE_OPTION_INPUT_OPTION_NUM_LAST \
                HWRM_NVM_VALIDATE_OPTION_INPUT_OPTION_NUM_RSVD_FFFF
        /*
         * Number of dimensions for this nvm configuration variable.
         * This value indicates how many of the indexN values to use.
         * A value of 0 means that none of the indexN values are valid.
         * A value of 1 requires at index0 is valued, a value of 2
         * requires that index0 and index1 are valid, and so forth
         */
        uint16_t        dimensions;
        /* index for the 1st dimensions */
        uint16_t        index_0;
        /* index for the 2nd dimensions */
        uint16_t        index_1;
        /* index for the 3rd dimensions */
        uint16_t        index_2;
        /* index for the 4th dimensions */
        uint16_t        index_3;
        uint8_t unused_0[2];
} __attribute__((packed));

/* hwrm_nvm_validate_option_output (size:128b/16B) */
struct hwrm_nvm_validate_option_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t result;
        /* indicates that the value provided for the option is not matching with the saved data. */
        #define HWRM_NVM_VALIDATE_OPTION_OUTPUT_RESULT_NOT_MATCH UINT32_C(0x0)
        /* indicates that the value provided for the option is matching the saved data. */
        #define HWRM_NVM_VALIDATE_OPTION_OUTPUT_RESULT_MATCH     UINT32_C(0x1)
        #define HWRM_NVM_VALIDATE_OPTION_OUTPUT_RESULT_LAST \
                HWRM_NVM_VALIDATE_OPTION_OUTPUT_RESULT_MATCH
        uint8_t unused_0[6];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_validate_option_cmd_err (size:64b/8B) */
struct hwrm_nvm_validate_option_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_VALIDATE_OPTION_CMD_ERR_CODE_UNKNOWN UINT32_C(0x0)
        #define HWRM_NVM_VALIDATE_OPTION_CMD_ERR_CODE_LAST \
                HWRM_NVM_VALIDATE_OPTION_CMD_ERR_CODE_UNKNOWN
        uint8_t unused_0[7];
} __attribute__((packed));

/*****************************
 * hwrm_nvm_factory_defaults *
 *****************************/


/* hwrm_nvm_factory_defaults_input (size:192b/24B) */
struct hwrm_nvm_factory_defaults_input {
        /* The HWRM command request type. */
        uint16_t        req_type;
        /*
         * The completion ring to send the completion event on. This should
         * be the NQ ID returned from the `nq_alloc` HWRM command.
         */
        uint16_t        cmpl_ring;
        /*
         * The sequence ID is used by the driver for tracking multiple
         * commands. This ID is treated as opaque data by the firmware and
         * the value is returned in the `hwrm_resp_hdr` upon completion.
         */
        uint16_t        seq_id;
        /*
         * The target ID of the command:
         * * 0x0-0xFFF8 - The function ID
         * * 0xFFF8-0xFFFE - Reserved for internal processors
         * * 0xFFFF - HWRM
         */
        uint16_t        target_id;
        /*
         * A physical address pointer pointing to a host buffer that the
         * command's response data will be written. This can be either a host
         * physical address (HPA) or a guest physical address (GPA) and must
         * point to a physically contiguous block of memory.
         */
        uint64_t        resp_addr;
        /* mode is 8 b */
        uint8_t mode;
        /* If set to 1, it will trigger restoration of factory default settings */
        #define HWRM_NVM_FACTORY_DEFAULTS_INPUT_MODE_RESTORE UINT32_C(0x0)
        /* If set to 1, it will trigger creation of factory default settings */
        #define HWRM_NVM_FACTORY_DEFAULTS_INPUT_MODE_CREATE  UINT32_C(0x1)
        #define HWRM_NVM_FACTORY_DEFAULTS_INPUT_MODE_LAST \
                HWRM_NVM_FACTORY_DEFAULTS_INPUT_MODE_CREATE
        uint8_t unused_0[7];
} __attribute__((packed));

/* hwrm_nvm_factory_defaults_output (size:128b/16B) */
struct hwrm_nvm_factory_defaults_output {
        /* The specific error status for the command. */
        uint16_t        error_code;
        /* The HWRM command request type. */
        uint16_t        req_type;
        /* The sequence ID from the original command. */
        uint16_t        seq_id;
        /* The length of the response data in number of bytes. */
        uint16_t        resp_len;
        uint8_t result;
        /* factory defaults created successfully. */
        #define HWRM_NVM_FACTORY_DEFAULTS_OUTPUT_RESULT_CREATE_OK \
                UINT32_C(0x0)
        /* factory defaults restored successfully. */
        #define HWRM_NVM_FACTORY_DEFAULTS_OUTPUT_RESULT_RESTORE_OK \
                UINT32_C(0x1)
        /* factory defaults already created. */
        #define HWRM_NVM_FACTORY_DEFAULTS_OUTPUT_RESULT_CREATE_ALREADY \
                UINT32_C(0x2)
        #define HWRM_NVM_FACTORY_DEFAULTS_OUTPUT_RESULT_LAST \
                HWRM_NVM_FACTORY_DEFAULTS_OUTPUT_RESULT_CREATE_ALREADY
        uint8_t unused_0[6];
        /*
         * This field is used in Output records to indicate that the output
         * is completely written to RAM.  This field should be read as '1'
         * to indicate that the output has been completely written.
         * When writing a command completion or response to an internal processor,
         * the order of writes has to be such that this field is written last.
         */
        uint8_t valid;
} __attribute__((packed));

/* hwrm_nvm_factory_defaults_cmd_err (size:64b/8B) */
struct hwrm_nvm_factory_defaults_cmd_err {
        /*
         * command specific error codes that goes to
         * the cmd_err field in Common HWRM Error Response.
         */
        uint8_t code;
        /* Unknown error */
        #define HWRM_NVM_FACTORY_DEFAULTS_CMD_ERR_CODE_UNKNOWN \
                UINT32_C(0x0)
        /* valid configuration not present to create defaults */
        #define HWRM_NVM_FACTORY_DEFAULTS_CMD_ERR_CODE_NO_VALID_CFG \
                UINT32_C(0x1)
        /* No saved configuration present to restore, restore failed */
        #define HWRM_NVM_FACTORY_DEFAULTS_CMD_ERR_CODE_NO_SAVED_CFG \
                UINT32_C(0x2)
        #define HWRM_NVM_FACTORY_DEFAULTS_CMD_ERR_CODE_LAST \
                HWRM_NVM_FACTORY_DEFAULTS_CMD_ERR_CODE_NO_SAVED_CFG
        uint8_t unused_0[7];
} __attribute__((packed));

#endif /* _HSI_STRUCT_DEF_DPDK_H_ */